Search NASA⌕ Search

SEARCH · Search NASA

Results for “control layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

The JPL Phase B interferometer testbed

Future NASA missions with large optical systems will require alignment stability at the nanometer level. However, design studies indicate that vibration resulting from on-board disturbances can cause jitter at levels three to four orders of magnitude greater than this. Feasibility studies have shown that a combination of three distinct control layers will be required for these missions, including disturbance isolation, active and passive structural vibration suppression, and active optical pathlength compensation. The CSI technology challenge is to develop these design and control approaches that can reduce vibrations in the optical train by a factor of 1000 to 10,000. The focus of the paper is on describing the Phase B Testbed structure and facility, as the experimental results are included in other papers presented at this same conference.

Eldred, Daniel B.↗

Membrane‐electrode assembly design parameters for optimal CO 2 reduction

Commercial-scale generation of carbon-containing chemicals and fuels by means of electrochemical CO 2 reduction (CO 2 R) requires electrolyzers operating at high current densities and product selectivities. Membrane-electrode assemblies (MEAs) have been shown to be suitable for this purpose. In such devices, the cathode catalyst layer controls both the rate of CO 2 R and the distribution of products. In this study, we investigate how the ionomer-to-catalyst ratio (I:Cat), catalyst loading, and catalyst-layer thickness influence the performance of a cathode catalyst layer containing Ag nanoparticles supported on carbon. In this paper, we explore how these parameters affect the cell performance and establish the role of the exchange solution (water vs. CsHCO 3 ) behind the anode catalyst layer in cell performance. We show that a high total current density is best achieved using an I:Cat ratio of 3 at a Ag loading of 0.01–0.1 mg Ag /cm 2 and with a 1.0 M solution of CsHCO 3 circulated behind the anode catalyst layer. For these conditions, the optimal CO partial current density depends on the voltage applied to the MEA. The work also reveals that the performance of the cathode catalyst layer is limited by a combination of the electrochemically active surface area and the degree to which mass transfer of CO 2 to the surface of the Ag nanoparticles and the transport of OH – anions away from it limit the overall catalyst activity. Hydration of the ionomer in the cathode catalyst layer is found not to be an issue when using an exchange solution. The insights gained allowed for a Ag CO 2 R MEA that operates between 200 mA/cm 2 and 1 A/cm 2 with CO faradaic efficiencies of 78–91%, and the findings and understanding gained herein should be applicable to a broad range of CO 2 R MEA-based devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The NASA/OAST telerobot testbed architecture

Through a phased development such as a laboratory-based research testbed, the NASA/OAST Telerobot Testbed provides an environment for system test and demonstration of the technology which will usefully complement, significantly enhance, or even replace manned space activities. By integrating advanced sensing, robotic manipulation and intelligent control under human-interactive supervision, the Testbed will ultimately demonstrate execution of a variety of generic tasks suggestive of space assembly, maintenance, repair, and telescience. The Testbed system features a hierarchical layered control structure compatible with the incorporation of evolving technologies as they become available. The Testbed system is physically implemented in a computing architecture which allows for ease of integration of these technologies while preserving the flexibility for test of a variety of man-machine modes. The development currently in progress on the functional and implementation architectures of the NASA/OAST Testbed and capabilities planned for the coming years are presented.

Matijevic, J. R.↗

Ni/Li Disordering in Layered Transition Metal Oxide: Electrochemical Impact, Origin, and Control

Lithium-ion batteries (LIBs) not only power most of today’s hybrid electric vehicles (HEV) and electric vehicles (EV) but also are considered as a very promising system for grid-level storage. Large-scale applications for LIBs require substantial improvement in energy density, cost, and lifetime. Layered Li(NixMnyCoz)O2 (NMC, x+y+z=1) materials from solid-solution approaches to LiMO2 (M = Ni, Mn, Co, etc) are the most promising candidates for their high reversible capacity, better environmental compatibility, and lower cost compared with the traditional LiCoO2. In order to further boost Li storage capacity, a great deal of attention has been directed toward developing Ni-rich NMCs. However, structural disorder as a result of Ni/Li exchange in octahedral sites becomes a critical issue when Ni content increases to high values, as it leads to a detrimental effect on Li diffusivity, cycling stability, first-cycle efficiency, and overall electrode performance. Increasing efforts have been dedicated to improving the electrochemical performance of NMC materials via reduction of cationic mixing. Therefore, it is important to summarize this research field and provide in-depth insight into impact of Ni/Li disorder on electrochemical characteristics in layered NMC materials and its origin to accelerate the future development of NMC materials with high performance. In this Account, we start by analyzing the impact of Ni/Li disorder on electrochemical characteristics in layered NMC materials. The antisite Ni in the Li layer can limit the rate performance by impeding the Li-ion transport. It will also degrade the cycling stability by inducing the anisotropic stress in the bulk structure. Nevertheless, the antisite Ni-ions don’t always bring drawbacks to the electrochemical performance, some studies including our works found that it can improve the thermal stability and the cycling structure stability of Ni-rich NMC materials. We next discussed the driving forces and the kinetic advantages accounting for the Ni/Li exchange and summarized that the steric effect of cation size and the magnetic interactions between TM cations are the two main driving forces to promote the Ni/Li exchange during synthesis procedure and the electrochemical cycling, and the low energy barrier of Ni2+ migration from the 3a site in TM layer to 3b site in Li layer further provides the kinetic advantage. Based on above understandings, we reviewed the progress made to control the Ni/Li disorder and summarized three main ways: (i) suppressing the driving force from the steric effect by ion exchange; (ii) tuning the magnetic interaction by cationic substitution; (iii) kinetic controlling of Ni migration. Finally, our brief outlooks on the future development of controlling the Ni/Li disorder in NMC materials are provided. It is believed that this Account will provide significant understanding and inspirations toward developing high-performance NMC materials with controlled Ni/Li disorder.

Zheng, Jiaxin↗

XMCD experimental station optimized for ultrathin magnetic films at HiSOR-BL14

We have constructed a system for in situ X-ray magnetic circular dichroism (XMCD) measurements of ultrathin magnetic films at the soft X-ray beamline HiSOR-BL14 at Hiroshima Synchrotron Radiation Center. The XMCD experimental station is directly connected to the beamline, and equipped with a sample fabrication chamber where various types of ultrathin magnetic films can be grown with monatomic layer control. XMCD spectra of the as-grown samples can be measured with adequate precision for the analysis of magnetic moments, under proper control of the light polarization in the beamline optics. This system has enabled the investigation of natural magnetic states in the ultrathin magnetic films without the influence of surface oxidation or any cap-layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advanced air transport concepts

The concepts of laminar flow control, very large all-wing aircraft, an aerial relay transportation system and alternative fuels, which would enable large improvements in fuel conservation in air transportation in the 1990's are discussed. Laminar boundary layer control through suction would greatly reduce skin friction and has been reported to reduce fuel consumption by up to 29%. Distributed load aircraft, in which all fuel and payload are carried in the wing and the fuselage is absent, permit the use of lighter construction materials and the elimination of fuselage and tail drag. Spanloader aircraft with laminar flow control could be used in an aerial relay transportation system which would employ a network of continuously flying liners supplied with fuel, cargo and crews by smaller feeder aircraft. Liquid hydrogen and methane fuels derived from coal are shown to be more weight efficient and less costly than coal-derived synthetic jet fuels.

Molloy, J. K.↗

Two experimental supercritical laminar-flow-control swept-wing airfoils

Two supercritical laminar-flow-control airfoils were designed for a large-chord swept-wing experiment in the Langley 8-Foot Transonic Pressure Tunnel where suction was provided through most of the model surface for boundary-layer control. The first airfoil was derived from an existing full-chord laminar airfoil by extending the trailing edge and making changes in the two lower-surface concave regions. The second airfoil differed from the first one in that it was designed for testing without suction in the forward concave region of the lower surface. Differences between the first airfoil and the one from which it was derived as well as between the first and second airfoils are discussed. Airfoil coordinates and predicted pressure distributions for the design normal Mach number of 0.755 and section lift coefficient of 0.55 are given for the three airfoils.

Allison, Dennis O.↗

Design and Performance Evaluation of a UWB Communication and Tracking System for Mini-AERCam

NASA Johnson Space Center (JSC) is developing a low-volume, low-mass, robotic free-flying camera known as Mini-AERCam (Autonomous Extra-vehicular Robotic Camera) to assist the International Space Station (ISS) operations. Mini-AERCam is designed to provide astronauts and ground control real-time video for camera views of ISS. The system will assist ISS crewmembers and ground personnel to monitor ongoing operations and perform visual inspections of exterior ISS components without requiring extravehicular activity (EAV). Mini-AERCam consists of a great number of subsystems. Many institutions and companies have been involved in the R&D for this project. A Mini-AERCam ground control system has been studied at Texas A&M University [3]. The path planning and control algorithms that direct the motions of Mini-AERCam have been developed through the joint effort of Carnegie Mellon University and the Texas Robotics and Automation Center [5]. NASA JSC has designed a layered control architecture that integrates all functions of Mini-AERCam [8]. The research described in this report is part of a larger effort focused on the communication and tracking subsystem that is designed to perform three major tasks: 1. To transmit commands from ISS to Mini-AERCam for control of robotic camera motions (downlink); 2. To transmit real-time video from Mini-AERCam to ISS for inspections (uplink); 3. To track the position of Mini-AERCam for precise motion control. The ISS propagation environment is unique due to the nature of the ISS structure and multiple RF interference sources [9]. The ISS is composed of various truss segments, solar panels, thermal radiator panels, and modules for laboratories and crew accommodations. A tracking system supplemental to GPS is desirable both to improve accuracy and to eliminate the structural blockage due to the close proximity of the ISS which could at times limit the number of GPS satellites accessible to the Mini-AERCam. Ideally, the tracking system will be a passive component of the communication system which will need to operate in a time-varying multipath environment created as the robot camera moves over the ISS structure. In addition, due to many interference sources located on the ISS, SSO, LEO satellites and ground-based transmitters, selecting a frequency for the ISS and Mini-AERCam link which will coexist with all interferers poses a major design challenge. To meet all of these challenges, ultrawideband (UWB) radio technology is being studied for use in the Mini-AERCam communication and tracking subsystem. The research described in this report is focused on design and evaluation of passive tracking system algorithms based on UWB radio transmissions from mini-AERCam.

Barton, Richard J.↗

A Multiport DC Transformer to Enable Flexible Scalable DC as a Service

The rapid adoption of new DC loads and sources, including photovoltaic arrays, DC fast charging of electric vehicle, battery energy storage and data centers, requires a large amount of DC power conversion. A majority of new deployments also necessitate the integration of multiple DC loads and sources at one site. The traditional approach to serve these new applications relies on multiple standard power converters, each dedicated to a source or load, and results in highly customized systems, with challenging control coordination, complex protection strategies, and poor scalability. Instead, this paper proposes the concept of a multiport DC transformer (MDCT) as a modular building block for realizing a flexible, scalable DC as a Service system and address this rapidly growing need. The MDCT uses the S4T to achieve very tight control of cycle-by-cycle energy exchange between multiple ports, with high efficiency. A single multiport converter replaces 4-6 distinct converters, integrates all energy flows and manages protection. As a result, a new layered control architecture is introduced to ensure stability and scalability of the MDCT, with multiple S4T power converter building blocks connected in parallel to realize a fully modular system and reach the target power levels.

30 DIRECT ENERGY CONVERSION↗

Optical pathlength control in the nanometer regime on the JPL phase B interferometer testbed

This paper describes experimental research being performed at the Jet Propulsion Laboratory to develop and validate control concepts arising out of NASA's Control Structure Interaction program. The facility is meant to be a ground testbed with relevance to a broad class of future precision optical space systems. The objective of the experimental program is to investigate a multi-layer control approach to the maintenance of nanometer level optical pathlength control in the presence of external disturbances and multiple structural resonances. A brief overview of the experimental facility is presented. The control design methodology is discussed, and several experimental results are presented.

O'Neal, Michael C.↗

Three-dimensional flow in a microgravity diffusion flame

The objective is to understand the fluid dynamics in the interaction of large scale, three-dimensional vortex structures and transitional diffusion flames in a microgravity environment. The vortex structures are used to provide a known perturbation of the type used in passive and active shear layer control techniques. 'Passive techniques' refers to manipulation of the system geometry to influence the three dimensional dynamics of vortex structures, and 'active' refers to any technique which adds energy (acoustic or kinetic) to the flow to influence the shear layer vortex dynamics. The passive forcing is provided by an elliptic jet cross section, and the active forcing is incorporated by perturbing the jet velocity.

Hertzberg, Jean↗

Splitting of Forced Elliptic Jets and Flames

The objective of this work is to understand the fluid dynamics in the interaction of large scale, three-dimensional vortex structures and transitional diffusion flames in a microgravity environment. The vortex structures are used to provide a known perturbation of the type used in passive and active shear layer control techniques. 'Passive techniques' refers to manipulation of the system geometry to influence the three dimensional dynamics of vortex structures, and 'active' refers to any technique which adds energy (acoustic or kinetic) to the flow to influence the shear layer vortex dynamics. In this work the passive forcing is provided by an elliptic jet cross-section, and the active forcing is incorporated by perturbing the jet velocity using a loudspeaker in the plenum section.

Hertzberg, J.↗

Development of Semi-Span Model Test Techniques

A computational investigation was performed to support the development of a semispan model test capability in the NASA Langley Research Center's National Transonic Facility. This capability is desirable for the testing of advanced subsonic transport aircraft at full-scale Reynolds numbers. A state-of-the-art three-dimensional Navier-Stokes solver was used to examine methods to improve the flow over a semi-span configuration. First, a parametric study is conducted to examine the influence of the stand-off height on the flow over the semispan model. It is found that decreasing the stand-off height, below the maximum fuselage radius, improves the aerodynamic characteristics of the semi-span model. Next, active sidewall boundary layer control techniques are examined. Juncture region blowing jets, upstream tangential blowing, and sidewall suction are found to improve the flow over the aft portion of the semispan model. Both upstream blowing and suction are found to reduce the sidewall boundary layer separation. The resulting near surface streamline patterns are improved, and found to be quite similar to the full-span results. Both techniques however adversely affect the pitching moment coefficient.

Milholen, William E., II↗

Results of LFC experiment on slotted swept supercritical airfoil in Langley's 8-foot transonic pressure tunnel

A large chord swept supercritical laminar-flow control (LFC) airfoil was designed, constructed, and tested in the Langley 8-foot Transonic Pressure Tunnel (TPT). The LFC airfoil experiment was established to provide basic information concerning the design and compatibility of high performance supercritical airfoils with suction boundary-layer control achieved through fine slots or porous surface concepts. Shockless pressure distribution was achieved. Full chord laminar flow was achieved on upper and lower surfaces. Full chord laminar flow was maintained at subcritical speeds and over large supercritical zones. Feasibility of combined suction laminarization and supercritical airfoil technology was demonstrated.

Brooks, Cuyler W., Jr.↗

Design and experimental evaluation of a swept supercritical Laminar Flow Control (LFC) airfoil

A large chord swept supercritical laminar flow control (LFC) airfoil was designed, constructed, and tested in the NASA Langley 8-ft Transonic Pressure Tunnel (TPT). The LFC airfoil experiment was established to provide basic information concerning the design and compatibility of high-performance supercritical airfoils with suction boundary layer control achieved through discrete fine slots or porous surface concepts. It was aimed at validating prediction techniques and establishing a technology base for future transport designs and drag reduction. Good agreement was obtained between measured and theoretically designed shockless pressure distributions. Suction laminarization was maintained over an extensive supercritical zone up to high Reynolds numbers before transition gradually moved forward. Full-chord laminar flow was maintained on the upper and lower surfaces at M sub infinity = 0.82 up to R sub c is less than or equal to 12 x 10 to the 6th power. When accounting for both the suction and wake drag, the total drag could be reducted by at least one-half of that for an equivalent turbulent airfoil. Specific objectives for the LFC experiment are given.

Harvey, W. D.↗

Development of Semi-Span Model Test Techniques

A computational investigation was performed to support the development of a semi-span model test capability in the NASA Langley Research Center's National Transonic Facility. This capability is desirable for the testing of advanced subsonic transport aircraft at full-scale Reynolds numbers. A state-of-the-art three-dimensional Navier-Stokes solver was used to examine methods to improve the flow over a semi-span configuration. First, a parametric study is conducted to examine the influence of the stand-off height on the flow over the semi-span model. It is found that decreasing the stand-off height, below the maximum fuselage radius, improves the aerodynamic characteristics of the semi-span model. Next, active sidewall boundary layer control techniques are examined. Juncture region blowing jets, upstream tangential blowing, and sidewall suction are found to improve the flow over the aft portion of the semi-span model. Both upstream blowing and suction are found to reduce the sidewall boundary layer separation. The resulting near surface streamline patterns are improved, and found to be quite similar to the full-span results. Both techniques however adversely affect the pitching moment coefficient.

Pulnam, L. Elwood↗

Control of boundary layer transition location and plate vibration in the presence of an external acoustic field

The experiment is aimed at controlling the boundary layer transition location and the plate vibration when excited by a flow and an upstream sound source. Sound has been found to affect the flow at the leading edge and the response of a flexible plate in a boundary layer. Because the sound induces early transition, the panel vibration is acoustically coupled to the turbulent boundary layer by the upstream radiation. Localized surface heating at the leading edge delays the transition location downstream of the flexible plate. The response of the plate excited by a turbulent boundary layer (without sound) shows that the plate is forced to vibrate at different frequencies and with different amplitudes as the flow velocity changes indicating that the plate is driven by the convective waves of the boundary layer. The acoustic disturbances induced by the upstream sound dominate the response of the plate when the boundary layer is either turbulent or laminar. Active vibration control was used to reduce the sound induced displacement amplitude of the plate.

Maestrello, L.↗

Recent modifications and calibration of the Langley low-turbulence pressure tunnel

Modifications to the Langley Low-Turbulence Pressure Tunnel are presented and a calibration of the mean flow parameters in the test section is provided. Also included are the operational capability of the tunnel and typical test results for both single-element and multi-element airfoils. Modifications to the facility consisted of the following: replacement of the original cooling coils and antiturbulence screens and addition of a tunnel-shell heating system, a two dimensional model-support and force-balance system, a sidewall boundary layer control system, a remote-controlled survey apparatus, and a new data acquisition system. A calibration of the mean flow parameters in the test section was conducted over the complete operational range of the tunnel. The calibration included dynamic-pressure measurements, Mach number distributions, flow-angularity measurements, boundary-layer characteristics, and total-pressure profiles. In addition, test-section turbulence measurements made after the tunnel modifications have been included with these calibration data to show a comparison of existing turbulence levels with data obtained for the facility in 1941 with the original screen installation.

Mcghee, R. J.↗