The Lunar Orbiter attitude control simulator.
Air-bearing facility for Lunar Orbiter attitude control system testing minimizing external disturbances in platform, platform mass deflection and room thermal currents
ATTITUDE CONTROL↗
SEARCH · Search NASA
Results for “control simulation testing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solar Sail Torque Model Characterization for the Near Earth Asteroid Scout Mission
Near Earth Asteroid Scout (NEA Scout) was a mission to test solar sail propulsion for orbital transfer from cislunar space to flyby and image an asteroid. One of the goals of the mission was to characterize the solar torque on the sail to ensure successful attitude control for the orbit transfer and imaging the asteroid. The simulation used to develop the flight attitude control software uses the generalized model for solar sails, a tensor equation of the forces and torques on sails of arbitrary shape. Rios-Reyes and Scheeres developed a general process to update the torque tensor coefficients using estimates of sail torque over a range of directions to the sun. Their process was adapted and implemented for the specific case of NEA Scout using spacecraft telemetry collected during sail characterization maneuvers in combination with simulation models and parameters. The NEA Scout maneuvers were limited to the operating range of the mission and constraints of the control hardware and allowed safe testing of each attitude before proceeding to the next. The NEA Scout reaction wheel speeds are used to measure accumulated momentum, while the Active Mass Translator (AMT) position is used to subtract out the torque from the center of mass crossed with the sail force and isolate the torque from only the sail shape. The process was tested by running attitude control simulations of the characterization maneuvers, generating simulated telemetry, estimating the solar torques, then using a least squares estimating the solar torque coefficients using least-squares and then performing a least-squares fit to the solar torque tensor coefficients. These estimated coefficients were tested by evaluating the solar torques under the same conditions as the simulated telemetry and comparing to the true simulated torques. Solar force model updates can be performed separately by observing the effect of the sail on the trajectory, and the torque model can be refined using those solar force updates. This process met the needs of the NEA Scout mission and can be adapted to characterize the solar torque for other missions with different sails.
solar sail↗
Solar Sail Torque Model Characterization for the Near Earth Asteroid Scout Mission
Near Earth Asteroid Scout (NEA Scout) was a mission to test solar sail propulsion for orbital transfer from cislunar space to flyby and image an asteroid. Had it succeeded, one of the mission goals was to characterize the solar torque on the sail to ensure successful attitude control for the orbit transfer and imaging the asteroid. The simulation used to develop the flight attitude control software uses the generalized model for solar sails, a tensor equation of the forces and torques on sails of arbitrary shape. Rios-Reyes and Scheeres developed a general process to update the torque tensor coefficients using estimates of sail torque over a range of directions to the sun. Their process was adapted and implemented for the specific case of NEA Scout using spacecraft telemetry collected during sail characterization maneuvers in combination with simulation models and parameters. The NEA Scout maneuvers were limited to the operating range of the mission and constraints of the control hardware and allowed safe testing of each attitude before proceeding to the next. The NEA Scout reaction wheel speeds are used to measure accumulated momentum, while the Active Mass Translator (AMT) position is used to subtract out the torque from the center of mass crossed with the sail force and isolate the torque from only the sail shape. The process was tested by running attitude control simulations of the characterization maneuvers, generating simulated telemetry, estimating the solar torques, then using a least squares estimating the solar torque coefficients using least-squares and then performing a least-squares fit to the solar torque tensor coefficients. These estimated coefficients were tested by evaluating the solar torques under the same conditions as the simulated telemetry and comparing to the true simulated torques. Solar force model updates can be performed separately by observing the effect of the sail on the trajectory, and the torque model can be refined using those solar force updates. This process met the needs of the NEA Scout mission and can be adapted to characterize the solar torque for other missions with different sails.
solar sail↗
Adaptive Force Control For Compliant Motion Of A Robot
Two adaptive control schemes offer robust solutions to problem of stable control of forces of contact between robotic manipulator and objects in its environment. They are called "adaptive admittance control" and "adaptive compliance control." Both schemes involve use of force-and torque sensors that indicate contact forces. These schemes performed well when tested in computational simulations in which they were used to control seven-degree-of-freedom robot arm in executing contact tasks. Choice between admittance or compliance control is dictated by requirements of the application at hand.
Seraji, Homayoun↗
Decentralized control experiments on the JPL flexible spacecraft
Decentralized control experiments were successfully demonstrated for the JPL/AFAL Flexible Structure. A simulation package using MATRIXx showed strong correlation between the simulations and experimental result, while providing a means for test and debug of the various control strategies. Implementation was simplified by a modular software design that was easily transported from the simulation environment to the experimental environment. Control designs worked well for suppression of the dominant modes of the structure. Static decentralized output feedback dampened the excited modes of the structure, but sometimes excited higher order modes upon startup of the controller. A second-order frequency shaping controller helped to eliminate excitation of the higher order modes by attenuating high frequencies in the control effort. However, it also resulted in slightly longer settling times.
Ozguner, U.↗
System Design Techniques for Reducing the Power Requirements of Advanced life Support Systems
The high power requirement associated with overall operation of regenerative life support systems is a critical Z:p technological challenge. Optimization of individual processors alone will not be sufficient to produce an optimized system. System studies must be used in order to improve the overall efficiency of life support systems. Current research efforts at NASA Ames Research Center are aimed at developing approaches for reducing system power and energy usage in advanced life support systems. System energy integration and energy reuse techniques are being applied to advanced life support, in addition to advanced control methods for efficient distribution of power and thermal resources. An overview of current results of this work will be presented. The development of integrated system designs that reuse waste heat from sources such as crop lighting and solid waste processing systems will reduce overall power and cooling requirements. Using an energy integration technique known as Pinch analysis, system heat exchange designs are being developed that match hot and cold streams according to specific design principles. For various designs, the potential savings for power, heating and cooling are being identified and quantified. The use of state-of-the-art control methods for distribution of resources, such as system cooling water or electrical power, will also reduce overall power and cooling requirements. Control algorithms are being developed which dynamically adjust the use of system resources by the various subsystems and components in order to achieve an overall goal, such as smoothing of power usage and/or heat rejection profiles, while maintaining adequate reserves of food, water, oxygen, and other consumables, and preventing excessive build-up of waste materials. Reductions in the peak loading of the power and thermal systems will lead to lower overall requirements. Computer simulation models are being used to test various control system designs.
Finn, Cory↗
Pre-Flight Testing of Spaceborne GPS Receivers using a GPS Constellation Simulator
The NASA Goddard Space Flight Center (GSFC) Global Positioning System (GPS) applications test facility has been established within the GSFC Guidance Navigation and Control Center. The GPS test facility is currently housing the Global Simulation Systems Inc. (GSSI) STR2760 GPS satellite 40-channel attitude simulator and a STR4760 12-channel navigation simulator. The facility also contains a few other resources such as an atomic time standard test bed, a rooftop antenna platform and a radome. It provides a new capability for high dynamics GPS simulations of space flight that is unique within the aerospace community. The GPS facility provides a critical element for the development and testing of GPS based technologies i.e. position, attitude and precise time determination used on-board a spacecraft, suborbital rocket balloon. The GPS simulation system is configured in a transportable rack and is available for GPS component development as well as for component, spacecraft subsystem and system level testing at spacecraft integration and tests sites. The GPS facility has been operational since early 1996 and has utilized by space flight projects carrying GPS experiments, such as the OrbView-2 and the Argentine SAC-A spacecrafts. The SAC-A pre-flight test data obtained by using the STR2760 simulator and the comparison with preliminary analysis of the GPS data from SAC-A telemetry are summarized. This paper describes pre-flight tests and simulations used to support a unique spaceborne GPS experiment. The GPS experiment mission objectives and the test program are described, as well as the GPS test facility configuration needed to verify experiment feasibility. Some operational and critical issues inherent in GPS receiver pre-flight tests and simulations using this GPS simulation, and test methodology are described. Simulation and flight data are presented. A complete program of pre-flight testing of spaceborne GPS receivers using a GPS constellation simulator is detailed.
Kizhner, Semion↗
Pre-Flight Testing of Spaceborne GPS Receivers Using a GPS Constellation Simulator
The NASA Goddard Space Flight Center (GSFC) Global Positioning System (GPS) applications test facility has been established within the GSFC Guidance Navigation and Control Center. The GPS test facility is currently housing the Global Simulation Systems Inc. (GSSI) STR2760 GPS satellite 40-channel attitude simulator and a STR4760 12-channel navigation simulator. The facility also contains a few other resources such as an atomic time standard test bed, a rooftop antenna platform and a radome. It provides a new capability for high dynamics GPS simulations of space flight that is unique within the aerospace community. The GPS facility provides a critical element for the development and testing of GPS based technologies i.e. position, attitude and precise time determination used on-board a spacecraft, suborbital rocket or balloon. The GPS simulator system is configured in a transportable rack and is available for GPS component development as well as for component, spacecraft subsystem and system level testing at spacecraft integration and test sites. The GPS facility has been operational since early 1996 and has been utilized by space flight projects carrying GPS experiments, such as the OrbView-2 and the Argentine SAC-A spacecrafts. The SAC-A pre-flight test data obtained by using the STR2760 simulator and the comparison with preliminary analysis of the GPS data from SAC-A telemetry are summarized. This paper describes pre-flight tests and simulations used to support a unique spaceborne GPS experiment. The GPS experiment mission objectives and the test program are described, as well as the GPS test facility configuration needed to verify experiment feasibility. Some operational and critical issues inherent in GPS receiver pre-flight tests and simulations using this GPS simulator, and test methodology are described. Simulation and flight data are presented. A complete program of pre-flight testing of spaceborne GPS receivers using a GPS constellation simulator is detailed.
Kizhner, Semion↗
A testbed for research on manipulator-coupled active spacecraft
This paper describes a testbed developed to study control of manipulator-coupled spacecraft with active attitude control systems. Pre-design simulation studies are described that were used to size and design the experimental facility and plan testing programs. Results on the dynamics and control of this testbed are presented that were obtained from both simulations and experiments. Initial experimental results have been used to refine the simulators using output matching system identification. Results from this system identification are included in the form of comparisons between simulation and experiment time histories for various model parameter values. These show that the testbed is inherently nonlinear and that parameters, harmonic gear effectiveness, in particular, have appreciable effects on the dynamics.
Montgomery, Raymond C.↗
Ground-based time-guidance algorithm for control of airplanes in a time-metered air traffic control environment: A piloted simulation study
The rapidly increasing costs of flight operations and the requirement for increased fuel conservation have made it necessary to develop more efficient ways to operate airplanes and to control air traffic for arrivals and departures to the terminal area. One concept of controlling arrival traffic through time metering has been jointly studied and evaluated by NASA and ONERA/CERT in piloted simulation tests. From time errors attained at checkpoints, airspeed and heading commands issued by air traffic control were computed by a time-guidance algorithm for the pilot to follow that would cause the airplane to cross a metering fix at a preassigned time. These tests resulted in the simulated airplane crossing a metering fix with a mean time error of 1.0 sec and a standard deviation of 16.7 sec when the time-metering algorithm was used. With mismodeled winds representing the unknown in wind-aloft forecasts and modeling form, the mean time error attained when crossing the metering fix was increased and the standard deviation remained approximately the same. The subject pilots reported that the airspeed and heading commands computed in the guidance concept were easy to follow and did not increase their work load above normal levels.
Knox, C. E.↗
Experiments in advanced control concepts for space robotics - An overview of the Stanford Aerospace Robotics Laboratory
The Stanford University Aerospace Robotics Laboratory is actively developing and experimentally testing advanced robot control strategies for space robotic applications. Early experiments focused on control of very lightweight one-link manipulators and other flexible structures. The results are being extended to position and force control of mini-manipulators attached to flexible manipulators and multilink manipulators with flexible drive trains. Experimental results show that end-point sensing and careful dynamic modeling or adaptive control are key to the success of these control strategies. Free-flying space robot simulators that operate on an air cushion table have been built to test control strategies in which the dynamics of the base of the robot and the payload are important.
Hollars, M. G.↗
Adaptive-wall wind-tunnel research at Ames Research Center
Adaptive-wall wind-tunnel research is summarized. This research includes small-scale two- and three-dimensional wind-tunnel experiments and numerical experiments with a three-dimensional adaptive-wall simulator. Airflow through the test-section walls is controlled by adjusting the pressures in segmented plenums. Interference free conditions are successfully attained in subsonic and transonic flows. An adaptive wall test section is constructed for the transonic wind tunnel. Wall interference was reduced in the three dimensional experiment at several angles of attack at Mach 0.60. A wing on wall configuration was modeled in the numerical experiments. These flow simulations showed that free air conditions can be approximated by adjusting boundary conditions at only the floor and ceiling of the test section. No sidewall control was necessary.
Schairer, E. T.↗
Hybrid-Electric Aero-Propulsion Controls Testbed Results with Energy Storage
Electrified aircraft propulsion (EAP) research is a priority of the National Aeronautics and Space Administration (NASA) for its potential to increase propulsion system efficiency, performance, and operability at the subsystem and vehicle levels while decreasing emissions. These EAP systems demand more advanced control algorithms due to increased complexity. NASA has developed a reconfigurable, hardware-in-the-loop rig to verify control algorithm performance using a sub-scale electro-mechanical system. A novel capability of this rig is the ability to test full scale EAP control algorithms on a sub-scale representation of the electro-mechanical system without turbomachinery/rotors. A novel feature is the use of a physical energy storage device within the electro-mechanical system. A dual spool, parallel hybrid-electric turbofan architecture and energy management control system is tested with the goal of verifying the ability to obtain turbomachinery model operability benefits while controlling sub-scale electro-mechanical hardware. Pre-test predictions of the turbofan model, control, and rig performance were obtained through simulation using a software model of the rig. Theoretical results showing the true performance of the turbofan model were obtained through a software simulation using full-scale mechanical shaft models. The paper compares theoretical, predicted, and actual test results from the turbofan model, energy management control and rig perspectives. The results show that the presence of sub-scale electro-mechanical hardware did not inhibit the energy management algorithm from achieving turbomachinery operability benefits.
hybrid↗
Hybrid-Electric Aero-Propulsion Controls Testbed Results with Energy Storage
Electrified aircraft propulsion (EAP) research is a priority of the National Aeronautics and Space Administration (NASA) for its potential to increase propulsion system efficiency, performance, and operability at the subsystem and vehicle levels while decreasing emissions. These EAP systems demand more advanced control algorithms due to increased complexity. NASA has developed a reconfigurable, hardware-in-the-loop rig to verify control algorithm performance using a sub-scale electro-mechanical system. A novel capability of this rig is the ability to test full scale EAP control algorithms on a sub-scale representation of the electro-mechanical system without turbomachinery/rotors. A novel feature is the use of a physical energy storage device within the electro-mechanical system. A dual spool, parallel hybrid-electric turbofan architecture and energy management control system is tested with the goal of verifying the ability to obtain turbomachinery model operability benefits while controlling sub-scale electro-mechanical hardware. Pre-test predictions of the turbofan model, control, and rig performance were obtained through simulation using a software model of the rig. Theoretical results showing the true performance of the turbofan model were obtained through a software simulation using full-scale mechanical shaft models. The paper compares theoretical, predicted, and actual test results from the turbofan model, energy management control and rig perspectives. The results show that the presence of sub-scale electro-mechanical hardware did not inhibit the energy management algorithm from achieving turbomachinery operability benefits.
hybrid↗
Ground Simulator Studies of a Nonlinear Linkage in a Power Control System
An investigation was made to determine the characteristics of a nonlinear linkage installed in a power control system incorporated in a ground simulator. The nonlinear linkage provided for increased control-stick motion for relatively small simulator response at control motions near neutral. The quality of the control system was rated on the ease and precision with which various tracking tasks were performed by the pilots who operated the simulator. The results obtained with the nonlinear linkage installed in the control system were compared with those obtained by using the normal linear control system. Several combinations of nonlinearity of the linkage were tested for various dynamic characteristics of the simulator. It was found that the pilots were able to track almost as well with the nonlinear linkage installed as with the normal system. All of the pilots were of the opinion, however, that the nonlinearity was an undesirable feature in the control system because of the apparent lack of simulator response through the neutral range of the linkage where relatively large stick deflections could be made with very little simulator motion. The results showed that increased lag between the target and chair position, higher stick-force levels, and uneven stick forces due to the dynamics of the linkage were general characteristics of all the nonlinear linkage conditions tested. It was also found that for cases of low simulator damping, rapid control motions caused considerably higher overshoots when the nonlinear linkage was installed than were obtained for the normal linear control system. These characteristics were considered to be sufficiently undesirable to out-weigh the advantages to be gained from the use of a nonlinear linkage in the control system of an airplane.
Assadourian, Arthur↗
Piloted Evaluation of Modernized Limited Authority Control Laws in the NASA-Ames Vertical Motion Simulator (VMS)
The UH-60 BLACK HAWK was designed in the 1970s, when the US Army primarily operated during the day in good visual conditions. Subsequently, the introduction of night-vision goggles increased the BLACK HAWK'S mission effectiveness, but the accident rate also increased. The increased accident rate is strongly tied to increased pilot workload as a result of a degradation in visual cues. Over twenty years of research in helicopter flight control and handling qualities has shown that these degraded handling qualities can be recovered by modifying the response type of the helicopter in low speed flight. Sikorsky Aircraft Corporation initiated a project under the National Rotorcraft Technology Center (NRTC) to develop modern flight control laws while utilizing the existing partial authority Stability Augmentation System (SAS) of the BLACK HAWK. This effort resulted in a set of Modernized Control Laws (MCLAWS) that incorporate rate command and attitude command response types. Sikorsky and the US Army Aeroflightdynamics Directorate (AFDD) conducted a piloted simulation on the NASA-Ames Vertical h4otion Simulator, to assess potential handling qualities and to reduce the risk of subsequent implementation and flight test of these modern control laws on AFDD's EH-60L helicopter. The simulation showed that Attitude Command Attitude Hold control laws in pitch and roll improve handling qualities in the low speed flight regime. These improvements are consistent across a range of mission task elements and for both good and degraded visual environments. The MCLAWS perform better than the baseline UH-60A control laws in the presence of wind and turbulence. Finally, while the improved handling qualities in the pitch and roll axis allow the pilot to pay more attention to the vertical axis and hence altitude performance also improves, it is clear from pilot comments and altitude excursions that the addition of an Altitude Hold function would further reduce workload and improve overall handling qualities of the aircraft.
Sahasrabudhe, Vineet↗
Verification of the Generalized Aerospace Simulation in Simulink
NASA uses six-degrees-of-freedom (6-DOF) simulations tools to design, test, develop Guidance Navigation and Control (GN&C) software, and certify vehicle performance prior to flight. Therefore, it is critical that the 6-DOF tools used for vehicle design and certification are validated. The focus of this work is the validation of the NASA Marshall Space Flight Center 6-DOF “GeneraLized Aerospace Simulation in Simulink” (GLASS) framework tool. The GLASS tool framework is currently used to support NASA GN&C insight for the Human Landing System (HLS) project, simulating vehicle dynamics during lunar descent and ascent. The GLASS framework utilizes the off-the-shelf Mathworks (R) Simscape (TM) Multibody (TM) toolbox to model vehicle multi-body dynamics. NASA’s Engineering and Safety Center (NESC) provides a set of 6-DOF simulation verification “check cases” that are available to any user needing to verify 6-DOF tools. The check cases contain seventeen atmospheric and twenty-six orbital test scenarios are provided to validate equations of motion, environmental models (e.g., atmosphere, gravitation, and geodesy) and tool propagators. This paper compares GLASS 6-DOF simulation results against the NESC check cases’ results via simulation-to-simulation comparisons. The comparison demonstrates that GLASS simulation results are “in family” with the outputs of the applicable NASA NESC check-cases and verify the GLASS core framework dynamics and the implementation of the check case scenario models.
6-Dof↗
Simulation and Flight Evaluation of a Parameter Estimation Input Design Method for Hybrid-Wing-Body Aircraft
As part of an effort to improve emissions, noise, and performance of next generation aircraft, it is expected that future aircraft will make use of distributed, multi-objective control effectors in a closed-loop flight control system. Correlation challenges associated with parameter estimation will arise with this expected aircraft configuration. Research presented in this paper focuses on addressing the correlation problem with an appropriate input design technique and validating this technique through simulation and flight test of the X-48B aircraft. The X-48B aircraft is an 8.5 percent-scale hybrid wing body aircraft demonstrator designed by The Boeing Company (Chicago, Illinois, USA), built by Cranfield Aerospace Limited (Cranfield, Bedford, United Kingdom) and flight tested at the National Aeronautics and Space Administration Dryden Flight Research Center (Edwards, California, USA). Based on data from flight test maneuvers performed at Dryden Flight Research Center, aerodynamic parameter estimation was performed using linear regression and output error techniques. An input design technique that uses temporal separation for de-correlation of control surfaces is proposed, and simulation and flight test results are compared with the aerodynamic database. This paper will present a method to determine individual control surface aerodynamic derivatives.
Taylor, Brian R.↗