Search NASA⌕ Search

SEARCH · Search NASA

Results for “correlation length”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Turbulent Statistics From Time-Resolved PIV Measurements of a Jet Using Empirical Mode Decomposition

Empirical mode decomposition is an adaptive signal processing method that when applied to a broadband signal, such as that generated by turbulence, acts as a set of band-pass filters. This process was applied to data from time-resolved, particle image velocimetry measurements of subsonic jets prior to computing the second-order, two-point, space-time correlations from which turbulent phase velocities and length and time scales could be determined. The application of this method to large sets of simultaneous time histories is new. In this initial study, the results are relevant to acoustic analogy source models for jet noise prediction. The high frequency portion of the results could provide the turbulent values for subgrid scale models for noise that is missed in large-eddy simulations. The results are also used to infer that the cross-correlations between different components of the decomposed signals at two points in space, neglected in this initial study, are important.

Dahl, Milo D.↗
NASA NTRS1984

An experimental investigation of two-dimensional thrust augmenting ejectors, part 2

The flow-field within a two-dimensional thrust augmenting ejector has been documented experimentally. Results are presented on the mean velocity field and the turbulent correlations by Laser Doppler Velocimeter, surface pressure distribution, surface temperature distribution, and thrust performance for two shroud geometries. The maximum primary nozzle pressure ratio tested was 3.0. The tests were conducted at primary nozzle temperature ratios of 1.0, 1.8 and 2.7. Two ejector characteristic lengths have been identified based on the dynamics of the ejector flow field, i.e., a minimum length L sub m below which no significant mixing occurs, and a critical length L sub c associated with the development of U'V' correlation in the ejector. These characteristic lengths divide the ejector flow field into three distinctive regions: the entrance region where there is no direct interaction between the primary flow and the ejector shroud; the interaction region where there is an increased momentum of induced flow near the shroud surface; and a pipe flow region characterized by an increased skin friction where x is the distance downstream from the ejector inlet. The effect of the coflowing induced flow has been shown to produce inside the ejector a centerline velocity that has increased over the free-jet data.

Bernal, L.↗
NASA NTRS1984

Effusion rate, length, and area relationships for some lava flows on Hawaii and Mount Etna with planetary implications

A model for the radiative cooling of thermally well mixed lava flows is presented and the relationship between effusion rate and length and area is analyzed. If radiative cooling is the prime mode of heat loss for a lava flow, one should expect to see a stronger correlation between the effusion rate and the plan area of the flow, than between effusion rate and just flow length. Different flows on a single volcano with differing initial temperatures, volatile content, and gross compositions should yield different areas for a given effusion rate. Likewise, a range of slopes for the relationship between effusion rate and flow area should result from comparisons between different volcanoes. As a test of these ideas, available data on the effusion rates, lengths, and areas of Hawaiian and Etnean flow is studied. It was found that: (1) the effusion rate/area correlation was statistically more significant than the correlation between effusion rate and length for four out of the five eruption episodes which met the necessary criteria of more than three individual flows with area, length, and effusion rate independently measured; (2) that there exists a minimum length and area for a given effusion rate, reflecting competition between overall characteristic proportionality between effusion rate and flow length, width, and area.

Pieri, D.↗
NASA NTRS2006

Aeolian Shear Stress Ratio Measurements within Mesquite-Dominated Landscapes of the Chihuahuan Desert, New Mexico, USA

A field study was conducted to ascertain the amount of protection that mesquite-dominated communities provide to the surface from wind erosion. The dynamics of the locally accelerated evolution of a mesquite/coppice dune landscape and the undetermined spatial dependence of potential erosion by wind from a shear stress partition model were investigated. Sediment transport and dust emission processes are governed by the amount of protection that can be provided by roughness elements. Although shear stress partition models exist that can describe this, their accuracy has only been tested against a limited dataset because instrumentation has previously been unable to provide the necessary measurements. This study combines the use of meteorological towers and surface shear stress measurements with Irwin sensors to measure the partition of shear stress in situ. The surface shear stress within preferentially aligned vegetation (within coppice dune development) exhibited highly skewed distributions, while a more homogenous surface stress was recorded at a site with less developed coppice dunes. Above the vegetation, the logarithmic velocity profile deduced roughness length (based on 10-min averages) exhibited a distinct correlation with compass direction for the site with vegetation preferentially aligned, while the site with more homogenously distributed vegetation showed very little variation in the roughness length. This distribution in roughness length within an area, defines a distribution of a resolved shear stress partitioning model based on these measurements, ultimately providing potential closure to a previously uncorrelated model parameter.

King, James↗
NASA NTRS1981

The deflection of a jet by confining surfaces

Thrust vectoring can be provided by the turning of a jet exhaust by the presence of confining surfaces. This approach is analogous to the upper surface blowing (USB) concept. Mean velocities, velocity autocorrelations, and pressure-velocity correlations are measured. From the autocorrelation curves, the Taylor microscales and the integral length scales are calculated. Convection velocities are calculated from the velocity space-time correlations. Two different confining surfaces (one flat, one with large curvature) are placed adjacent to the lip of a circular nozzle, and the resultant effects on the flow field are determined. In addition, two velocity ratios (exit plane velocity to ambient stream velocity) are examined. The velocity measurements were made with a laser Doppler velocimeter in conjunction with a phase locked-loop processor. Pressure measurements were made using a 1/8th inch condensor type microphone.

Catalano, G. D.↗
NASA NTRS1978

Correlations of catalytic combustor performance parameters

Correlations for combustion efficiency percentage drop and the minimum required adiabatic reaction temperature necessary to meet emissions goals of 13.6 g CO/kg fuel and 1.64 g HC/kg fuel are presented. Combustion efficiency was found to be a function of the cell density, cell circumference, reactor length, reference velocity, and adiabatic reaction temperature. The percentage pressure drop at an adiabatic reaction temperature of 1450 K was found to be proportional to the reference velocity to the 1.5 power and to the reactor length. It is inversely proportional to the pressure, cell hydraulic diameter, and fractional open area. The minimum required adiabatic reaction temperature was found to increase with reference velocity and decrease with cell circumference, cell density and reactor length. A catalyst factor was introduced into the correlations to account for differences between catalysts. Combustion efficiency, the percentage pressure drop, and the minimum required adiabatic reaction temperature were found to be a function of the catalyst factor. The data was from a 12 cm-diameter test rig with noble metal reactors using propane fuel at an inlet temperature of 800 K.

Bulzan, D. L.↗
NASA NTRS1987

On local approximations of the pressure-strain term in turbulence models

The results of numerical simulations of turbulent channel flows were used to examine the validity of the local approximation of the pressure-strain term in the Reynolds stress transport equation. Outside of the viscous sublayer the local approximation compares very well with the exact pressure strain. This agreement is due, at least in part, to the high correlation between the rapid pressure and its Laplacian, which suggests that only the near parts of the flow contribute to the rapid pressure at a point. In the viscous sublayer the distance over which the mean shear can be considered constant is comparable to the length scale in the normal direction of the correlations of velocity gradients, leading to failure of the local approximation.

Bradshaw, P.↗
NASA NTRS2001

Soybean cell enlargement oscillates with a temperature-compensated period length of ca. 24 min

Rate of enlargement of epidermal cells from soybean, when measured at intervals of 1 min using a light microscope equipped with a video measurement system, oscillated with a period length of about 24 min. This oscillation parallels the 24-min periodicity observed for the oxidation of NADH by the external plasma membrane NADH oxidase. The increase in length was not only non-linear, but intervals of rapid increase in area alternated with intervals of rapid decrease in area. The length of the period was temperature compensated, and was approximately the same when measured at 14, 24 and 34 degrees C even though the rate of cell enlargement varied over this same range of temperatures. These observations represent the first demonstration of an oscillatory growth behavior correlated with a biochemical activity where the period length of both is independent of temperature (temperature compensated) as is the hallmark of clock-related biological phenomena.

NASA Discipline Cell Biology↗
NASA NTRS1987

Thermal stability effects on the structure of the velocity field above an air-water interface

Mean velocity and turbulence measurements are described for turbulent flows above laboratory water waves, under various wind and thermal stratification conditions. Experimental results, when presented in the framework of Monin-Obukhov (1954) similarity theory, support local scaling based on evaluation of stratification effects at the same nondimensional distance from the mean water surface. Such scaling allows an extension of application of the above theory to the outer region of the boundary layer. Throughout the fully turbulent region, ratios of mean velocity gradients, eddy viscosities, and turbulence intensities under nonneutral and neutral conditions correlate well with the parameter z/Lambda (Lambda being a local Obukhov length and z the vertical coordinate of the mean air flow) and show good agreement with established field correlations. The influence of stratification on the wind-stress coefficient can be estimated from an empirical relationship in terms of its value under neutral conditions and a bulk Richardson number.

Papadimitrakis, Y. A.↗
NASA NTRS1992

Near-wall reconstruction of higher order moments and length scales using the POD

An analysis of the near-wall behavior of the proper orthogonal decomposition (POD) eigenfunctions derived from direct numerical simulation (DNS) of channel flow is performed. Consistent with previous studies, a low order multi-mode reconstruction of the kinetic energy and Reynolds shear stress suffices. A similar reconstruction of the isotropic dissipation rate is shown to be insufficient, however. An analysis is performed of the multi-mode composition of the dissipation rate in the near-wall region, and it is shown that a significant number of higher-order modes are required to achieve the correct asymptotic consistency in the near-wall region. In an attempt to avoid this problem, a length scale definition is proposed in terms of an integration of the correlation tensor which factors in the presence of the wall. The wall is accounted for by only integrating out to 2y(+) and not over the entire domain. Viscous and inviscid estimates for the dissipation were used in the near-wall and core regions respectively, in conjunction with this length scale representation to obtain an estimate of the dissipation throughout the domain. The resulting dissipation exhibits the proper behavior near the wall and in the inertial layer. A 1 POD mode estimate of the length scale is computed and found to agree quite well with the length scale obtained when the entire correlation tensor is used.

Glauser, Mark N.↗
NASA NTRS2014

Simulated Time Lags of Hinode/XRT and SDO/AIA Lightcurves as an Indication of Loop Heating Scenario

The precise nature of the heating mechanism (location, duration) in coronal loops is still a matter of enormous research. We present results from a 1D hydrodynamic loop simulation of a coronal loop which was run using different parameters such as loops length (50, 200, and 500 Mm), maximum temperature reached (3MK and 10MK), and abundances. For each scenario the model outputs were used to calculate the corresponding lightcurves as seen by XRT/Be-thin and various EUV AIA channels. The lag time between the peak of these lightcurves was computed using cross-correlation and plotted as a function of loop length. Additional results were computed using the 0D EBTEL code in order to test the compatibility of the two codes and to investigate additional loop lengths. Initial results indicate that the long (greater than 5000s) lags observed in the approx. 100Mm loops of active regions can only be reproduced using photospheric abundances and much longer loop lengths.

Alexander, Caroline↗
NASA NTRS2014

Simulated Time Lags of Hinode/XRT and SDO/AIA Lightcurves as an Indication of Loop Heating Scenario

The precise nature of the heating mechanism in coronal loops is still a matter of enormous research. We present the results from a 1D hydrodynamic loop simulation of a coronal loop which was run using different parameters such as loops length (50, 200 and 500 Mm), maximum temperature reached (3MK and 10 MK0, and abundances. For each scenario the model outputs were used to calculate the corresponding lightcurves as seen by XRT/Be-thin and various EUV AIA channels. The lag time between the peak of these lightcurves was computed and tested using cross-correlation and plotted as a function of loop length.

Loop heating↗
NASA NTRS2000

Identified motor terminals in Drosophila larvae show distinct differences in morphology and physiology

In Drosophila, the type I motor terminals innervating the larval ventral longitudinal muscle fibers 6 and 7 have been the most popular preparation for combining synaptic studies with genetics. We have further characterized the normal morphological and physiological properties of these motor terminals and the influence of muscle size on terminal morphology. Using dye-injection and physiological techniques, we show that the two axons supplying these terminals have different innervation patterns: axon 1 innervates only muscle fibers 6 and 7, whereas axon 2 innervates all of the ventral longitudinal muscle fibers. This difference in innervation pattern allows the two axons to be reliably identified. The terminals formed by axons 1 and 2 on muscle fibers 6 and 7 have the same number of branches; however, axon 2 terminals are approximately 30% longer than axon 1 terminals, resulting in a corresponding greater number of boutons for axon 2. The axon 1 boutons are approximately 30% wider than the axon 2 boutons. The excitatory postsynaptic potential (EPSP) produced by axon 1 is generally smaller than that produced by axon 2, although the size distributions show considerable overlap. Consistent with vertebrate studies, there is a correlation between muscle fiber size and terminal size. For a single axon, terminal area and length, the number of terminal branches, and the number of boutons are all correlated with muscle fiber size, but bouton size is not. During prolonged repetitive stimulation, axon 2 motor terminals show synaptic depression, whereas axon 1 EPSPs facilitate. The response to repetitive stimulation appears to be similar at all motor terminals of an axon. Copyright 2000 John Wiley & Sons, Inc.

NASA Discipline Neuroscience↗
NASA NTRS1972

Evaluation of the hazard from exposure to electron irradiation simulating that in the synchronous orbit

The electron spectrum predicted for the synchronous orbit was simulated to determine the effects that might occur to astroscientists exposed to such irradiation while on a prolonged space station mission in that region. Miniature pigs were exposed to monoenergetic and spectral-fractionated irradiations with 0.5 to 2.1 MeV electrons. Clinical and pathological alterations observed in biopsies were correlated with depth-dose pattern and length of post irradiation period up to one year. With monoenergetic electrons, the lowest dose causing a recognizable lesion was 1450 rad and with increasing dose lesions appeared earlier and were more severe. At the highest dose given, 2650 rad, ulceration extending into the dermis was present by twenty one days and required about four months for complete healing. Spectral-fractionated irradiations, in which the total dose range was essentially comparable to that of the monoenergetic series, resulted in very minimal outer dermis edema at 1790 rad and at no dose employed did necrosis of epidermis or ulceration into dermis occur.

Lippincott, S. W.↗
NASA NTRS1972

Effects of eccentricities and lateral pressure on the design of stiffened compression panels

An analysis for determining the effects of eccentricities and lateral pressure on the design of stiffened compression panels is presented. The four types of panel stiffeners considered are integral, zee, integral zee, and integral tee. Mass-strength curves, which give the mass of the panel necessary to carry a specified load, are given along with related design equations needed to calculate the cross-sectional dimensions of the minimum-mass-stiffened panel. The results of the study indicate that the proportions of the panels are geometrically similar to the proportions of panels designed for no eccentricity or lateral pressure, but no cross-sectional dimensions are greater, resulting in significantly increased mass. The analytical minimum-mass designs of zee-stiffened panels are compared with designs from experimentally derived charts. An assumed eccentricity of 0.001 times the length of the panel is used to correlate the analytical and experimental data. Good correlation between the experimentally derived and the analytical curves is obtained for the range of loading where materials yield governs the design. At lower loads the mass given by the analytical curve using this assumed eccentricity is greater than that given by the experimental results.

Giles, G. L.↗
NASA NTRS1981

Mixing of a passive scalar in isotropic and sheared homogeneous turbulence

In order to calculate the velocity and scalar fields, the three dimensional, time-dependent equations of motion and the diffusion equation were solved numerically. The following cases were treated: isotropic, homogeneous turbulence with decay of a passive scalar; and homogeneous turbulent shear flow with a passive scalar whose mean varies linearly in the spanwise direction. The solutions were obtained at relatively low Reynolds numbers so that all of the turbulent scales could be resolved without modeling. Turbulent statistics such as integral length scales, Taylor microscales, Kolmogorov length scale, one- and two-point correlations of velocity-velocity and velocity-scalar, turbulent Prandtl/Schmidt number, r.m.s. values of velocities, the scalar quantity and pressure, skewness, decay rates, and decay exponents were calculated. The results are compared with the available expermental results, and good agreement is obtained.

Shirani, E.↗
NASA NTRS1984

Analysis of the NASA/MSFC Airborne Doppler Lidar results from San Gorgonio Pass, California

Two days during July of 1981 the NASA/MSFC Airborne Doppler Lidar System (ADLS) was flown aboard the NASA/AMES Convair 990 on the east side of San Gorgonio Pass California, near Palm Springs, to measure and investigate the accelerated atmospheric wind field discharging from the pass. The vertical and horizontal extent of the fast moving atmospheric flow discharging from the San Gorgonio Pass were examined. Conventional ground measurements were also taken during the tests to assist in validating the ADLS results. This particular region is recognized as a high wind resource region and, as such, a knowledge of the horizontal and vertical extent of this flow was of interest for wind energy applications. The statistics of the atmospheric flow field itself as it discharges from the pass and then spreads out over the desert were also of scientific interests. This data provided the first spatial data for ensemble averaging of spatial correlations to compute longitudinal and lateral integral length scales in the longitudinal and lateral directions for both components.

Cliff, W. C.↗