Search NASA⌕ Search

SEARCH · Search NASA

Results for “curing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Photopolymerization of Dual-Cure System in 3D Printing

Two posters for two different symposiums are included here. The poster information is the same; it is just for two different events hosted by different summer cohorts. The START HBCU MSIPP Symposium on July 30th, 2025 and the SIP Intern Symposium on August 7th, 2025.

Mason, Samaiyah K.A. [Sandia National Laboratories↗
NASA NTRS1974

Method for compression molding of thermosetting plastics utilizing a temperature gradient across the plastic to cure the article

A method is described for compression molding of thermosetting plastics composition. Heat is applied to the compressed load in a mold cavity and adjusted to hold molding temperature at the interface of the cavity surface and the compressed compound to produce a thermal front. This thermal front advances into the evacuated compound at mean right angles to the compression load and toward a thermal fence formed at the opposite surface of the compressed compound.

Heier, W. C.↗
NASA NTRS1974

Seeing - Its cause and cure

Following Fried, the statistics of images formed by an annular telescope aperture looking through the turbulent atmosphere are calculated; the deleterious effect of a central obscuration is much larger in the presence of seeing that for the telescope alone. A method of optimizing resolution through the atmosphere is explained in detail, with particular attention to the requirements for image-motion compensation; under ideal conditions, about a factor-of-four increase in effective resolution over conventional photography can be obtained. The effective resolution can be large or smaller than the 'seeing disk', depending on the recorded signal-to-noise ratio. Some common misconceptions about image structure and motion, and various unsound proposals for beating the seeing, are criticized.

Young, A. T.↗
NASA NTRS1979

Low-temperature elastomer production and curing

Thermally and chemically stable polymers are needed for materials applications, particularly highly-stable elastomers for solid propellant binders where initial high temperature required for dissolving anhydride in polymer is deerimental. Solvent reactant system allows polymerization without condensation of products under low heat. Solvents utilized were dimethylacetamide, dimethyflormamide, etc.

Ingham, J. D.↗
NASA NTRS1978

Ambient cure polyimide foams

Flame and temperature resistant polyimide foams are prepared by the reaction of an aromatic dianhydride, (pyromellitic dianhydride) with an aromatic polyisocyanate, (polymethylene polyphenylisocyanate), in the presence of an inorganic acid and furfuryl alcohol. Usable acids include dilute sulfuric acid, dilute nitric acid, hydrochloric acid, polyphosphoric acid, and phosphoric acid, with the latter being preferred. The dianhydride and the isocyanate in about equimolar proportions constitute about 50% of the reaction mixture, the rest being made up with the acid and the alcohol in a ratio of about 1:10. An exothermic reaction between the acid and the alcohol provides the heat necessary for the other components to polymerize without recourse to external heat sources. The mixture can be sprayed on any surface to form polymeric foam in locations where the application of heat is not practical or possible, for instance, between walls or on mine tunnel surfaces.

Sawko, P. M.↗
NASA NTRS1979

Environmental effects on space shuttle reusable surface insulation coated with reaction cured glass

Sample titles of the space shuttle reusable surface insulation was subjected alternately to simulated mission heating and either real or simulated environmental exposure for up to 34 cycles. The coating cracked as a result of exposure to high temperature and moisture conditions, and insulation with cracked coatings absorbed significant quantities of water in the launch-pad environment. Cracking was a complex function of time, temperature, and moisture exposure. Cracked coatings remained adherent to the insulation for up to 24 cycles past initial cracking.

Ransone, P. O.↗
NASA NTRS1979

Thermal Expansion and Swelling of Cured Epoxy Resin Used in Graphite/Epoxy Composite

The thermal expansion and swelling of resin material as influenced by variations in temperature during moisture absorption is discussed. Comparison measurements using composites constructed of graphite fibers and each of two epoxy resin matrices are included. Polymer theory relative to these findings is discussed and modifications are proposed.

Adamson, M. J.↗
NASA NTRS1980

Effects of moisture, residual thermal curing stresses and mechanical load on the damage development in quasi-isotropic laminates

Classical laminate theory and a finite element model were used to predict stress states prior to the first formation of damage in laminates fabricated from T/300/5208. Crack patterns characteristic of the laminate in a wet or dry condition were also predicted using a shear lag model. Development of edge damage was recorded and observed during the test by transferring an image of the damage from the edge surface on to a thin acetate sheet such that the damage imprinted could be immediately viewed on a microfiche card reader. Moisture was shown to significantly alter the interior and edge dry stress states due to swelling and a reduction of elastic properties and to reduce the transverse strength in 90 deg plies. A model was developed in order to predict changes in first ply failure laminate loads due to differences in stacking sequence together with a wet or dry environmental condition.

Kriz, R. D.↗
NASA NTRS1982

Neutralizing Amine-Cured Epoxy Surfaces

New surface treatment is a rapid, convenient, and effective method for converting unused amines and amine functional groups into neutral, noncorrosive substituted urea. Reaction proceeds at room temperature, takes only a few minutes, and leaves no corrosive residue. Surface should first be washed with alcohol to remove as much as possible of unreacted amine. Then it should be dried, since residual moisture or alcohol may consume some of treatment reagent and neutralization may then be incomplete.

Lee, S. Y.↗
NASA NTRS1983

More-Uniform Heat Curing for Structural Repairs

Copper lining helps to distribute heat under heating blanket. Bond during setup employs heating blanket over copper sheet within vacuum bag. Copper sheet smoothes out temperature distribution under hotspots in heater. Method applicable to uniformly heating such low-thermal-conductivity metals as titanium or stainless steel.

Bauer, P. E.↗
NASA NTRS1982

Effects of moisture, residual thermal curing stresses, and mechanical load on the damage development in quasi-isotropic laminates

This investigation demonstrates how moisture absorbed in (0/+ or - 45/90)s and (0/90/+ or - 45)s graphite epoxy laminates significantly alters the stress state and chronology of damage development along the laminate edge during static tension and tension-tension cyclic loading. Emphasis is placed on using reasonable approximations for wet and dry elastic properties, including out-of-plane properties (nu sub 23 and G sub 23), since these properties are required by finite element and shear lag models to predict the stress state at the laminate edge. Moisture was observed to alter the dry edge stress state in the 90-deg plies of the (0/+ or - 45/90)s laminate such that delaminations occurred at a lower load and transverse cracks occurred at a higher load. A model was developed which predicted the differences in loads required to initiate damage in the 90-deg plies of the two laminates in the wet and dry conditions. Although moisture can alter the chronology of damage development, the damage state in each laminate observed prior to fracture appeared to be independent of moisture content.

Kriz, R. D.↗