Results for “demand technology” — Page 19

NASA NTRS2017

Personal Rotorcraft Design and Performance with Electric Hybridization

Recent and projected improvements for more or all-electric aviation propulsion systems can enable greater personal mobility, while also reducing environmental impact (noise and emissions). However, all-electric energy storage capability is significantly less than present, hydrocarbon-fueled systems. A system study was performed exploring design and performance assuming hybrid propulsion ranging from traditional hydrocarbon-fueled cycles (gasoline Otto and diesel) to all-electric systems using electric motors generators, with batteries for energy storage and load leveling. Study vehicles were a conventional, single-main rotor (SMR) helicopter and an advanced vertical takeoff and landing (VTOL) aircraft. Vehicle capability was limited to two or three people (including pilot or crew); the design range for the VTOL aircraft was set to 150 miles (about one hour total flight). Search and rescue (SAR), loiter, and cruise-dominated missions were chosen to illustrate each vehicle and degree of hybrid propulsion strengths and weaknesses. The traditional, SMR helicopter is a hover-optimized design; electric hybridization was performed assuming a parallel hybrid approach by varying degree of hybridization. Many of the helicopter hybrid propulsion combinations have some mission capabilities that might be effective for short range or on-demand mobility missions. However, even for 30 year technology electrical components, all hybrid propulsion systems studied result in less available fuel, lower maximum range, and reduced hover and loiter duration than the baseline vehicle. Results for the VTOL aircraft were more encouraging. Series hybrid combinations reflective of near-term systems could improve range and loiter duration by 30. Advanced, higher performing series hybrid combinations could double or almost triple the VTOL aircrafts range and loiter duration. Additional details on the study assumptions and work performed are given, as well as suggestions for future study effort.

electric motors↗

NASA NTRSDate not supplied

A Predictive GNSS Performance Monitor for Autonomous Air Vehicles in Urban Environments

The emergence and development of advanced technologies and vehicle types has created a growing demand for the introduction of new forms of flight operations. These new and increasingly complex operational paradigms such as Advanced and Urban Air Mobility (AAM/UAM) present regulatory authorities and the aviation community with several design and implementation challenges – particularly for highly autonomous vehicles. An overarching and daunting task is finding methods to integrate these emerging operations without compromising safety or disrupting traditional airspace operations. A shift toward a more predictive risk mitigation capability becomes critical to meet this challenge. This paper focus on the development and testing of a prognostic service aimed at estimating the quality of Global Navigation Satellite System (GNSS) performance for an autonomous aircraft in complex environments. The intent of this function is to proactively reduce a flight operations risk of exposure to states that may induce poor or unacceptable navigation system performance by factoring in estimates of GNSS quality into pre-flight and/or in-flight route planning. Methodologies for producing quality estimates are specified and results are provided for selected simulation and flight test cases.

GNSS↗

NASA NTRSDate not supplied

A High-Performance Computing GNSS-aware Path Planning Algorithm for Safe Urban Flight Operations

The emergence and development of advanced technologies and vehicle types have created a growing demand for new forms of flight operations. These new and increasingly complex operational paradigms, such as Advanced and Urban Air Mobility (AAM/UAM), present regulatory authorities and the aviation community with several design-and-implementation challenges – particularly for highly autonomous vehicles. An overarching and daunting task is to develop protocols that can integrate these operations without compromising safety or disrupting traditional airspace operations. A shift toward a more predictive, autonomous, risk mitigation capability becomes critical to meet this challenge. This paper proposes and evaluates a computationally-efficient path planning approach to perform pre-flight planning and autonomous in-flight re-routing to minimize exposures to selected hazards. In our evaluation, hazards associated with degraded and missing critical GPS navigation data are considered. In this paper, we first present a high-performance computing path planning approach based on an adapted Bellman-Ford algorithm, developed in the CUDA programming language. Using the adapted path planning algorithm, we test this algorithm when encountering issues with GPS quality, and deliver an implementation that can produce flight paths that minimize exposure to risks, while maintaining a low computational burden. In our evaluation, the computation of periodic and aperiodic path updates are evaluated, prioritizing specific events as triggers for updates, based on changes to satellite availability. These critical events can lead to significant exposure to navigational hazards if not dealt with correctly.

GNSS↗

NASA NTRSDate not supplied

A High-Performance Computing GNSS-aware Path Planning Algorithm for Safe Urban Flight Operations

The emergence and development of advanced technologies and vehicle types have created a growing demand for new forms of flight operations. These new and increasingly complex operational paradigms, such as Advanced and Urban Air Mobility (AAM/UAM), present regulatory authorities and the aviation community with several design-and-implementation challenges – particularly for highly autonomous vehicles. An overarching and daunting task is to develop protocols that can integrate these operations without compromising safety or disrupting traditional airspace operations. A shift toward a more predictive, autonomous, risk mitigation capability becomes critical to meet this challenge. This paper proposes and evaluates a computationally-efficient path planning approach to perform pre-flight planning and autonomous in-flight re-routing to minimize exposures to selected hazards. In our evaluation, hazards associated with degraded and missing critical GPS navigation data are considered. In this paper, we first present a high-performance computing path planning approach based on an adapted Bellman-Ford algorithm, developed in the CUDA programming language. Using the adapted path planning algorithm, we test this algorithm when encountering issues with GPS quality, and deliver an implementation that can produce flight paths that minimize exposure to risks, while maintaining a low computational burden. In our evaluation, the computation of periodic and aperiodic path updates are evaluated, prioritizing specific events as triggers for updates, based on changes to satellite availability. These critical events can lead to significant exposure to navigational hazards if not dealt with correctly.

GNSS↗

NASA NTRS2023

Joint Augmented Reality Visual Informatics System: Concept of Operations

NASA proposed requirements for a digital display for an EVA spacesuit to provide relevant information to the crew member. The Joint Augmented Reality Visual Informatics System (Joint AR) project pursued four years of research and development towards a suit-display system in a near-eye, AR form factor. The project was responsible for developing software (custom graphics engine and core flight software), physical hardware prototyping (controls, projection display optics, suited display platform), virtual prototyping platform (a virtual reality testbed), and human-in-the-loop (HITL) operational testing informed by EVA flight controllers, crew members, and human factors engineers for con-ops definition. This document contains substantial updates to CTSD-ADV-1788 Rev. Basic. This revision was produced by the project to summarize the use-cases and and user experiences developed throughout the project, and refine the Basic revision originally drafted at the beginning of the project life cycle. The primary purpose of this document is to summarize and make available the scenario development efforts that have been pursued and explored within the Joint AR project. This includes descriptions of the scenarios themselves as well as corresponding potential of advanced informatics displays to support those specified scenarios. In doing so, this document provides a variety of approaches to deconstruct and hypothesize how future technological capabilities so that with future EVA work demands can be satisfied within future human planetary spaceflight missions.

Matthew Miller↗

NASA NTRSDate not supplied

Plasma Processing of Water and Inedible Biomass Ash Leaching

Researchers at Kennedy Space Center have developed a technology that generates plasma activated water in pH ranges that allow for the addition of nitrates and other nutrients to the water while maintaining a healthy pH for plants. A plasma torch is used to treat inedible biomass, generating ash containing nutrients useful for plant growth. The same plasma torch is also used to treat water, which results in the formation of nitric acid that lowers the pH of the water. Adding the plasma generated ash to the plasma treated water can balance the pH of the water to make it suitable for plant growth while simultaneously adding nutrients recycled from the inedible biomass to further enhance plant development. Plasma treatment of water to high and low pH extremes can also be used for sanitation purposes, causing pH shock to undesired organisms. The uniqueness of this process is the adjustability of the pH with one system. The same plasma system can be used to treat both the water and the biomass. Additionally, the technology can be used as an on-demand, point-of-use method for producing nitric acid.

Space Crop Production↗

NASA NTRSDate not supplied

Qualification of a Pulsed, Millinewton Class Metal Plasma Thruster for Broad Mission Applications

In the field of low power (<100W) electric propulsion, all thruster options demand significant trade-offs between operating parameters, reliability and scalable cost. With many systems on the market there are concerns with reliability, the need for extra considerations such as electron neutralizers for pure ion plumes, and the cost or craft compatibility of propellants. The Metal Plasma Thruster (MPT) is a new type of electric propulsion technology intended for low power applications. The system imparts momentum using inert, solid metal pucks as a propellant by using pulsed power to convert the metal into high velocity (~17km/s for Mo) jets of quasi-neutral plasma. The MPT technology does not require gas or liquid propellants, neutralizers, standby heaters, high voltage electronics, high electric or magnetic fields to operate. This comparatively simple pulsed operation is amenable to closed loop control, which provides for fine thrust control and S/C directed impulse on demand. Furthermore, the technology can use any metal as propellant, opening up unique opportunities for In-Situ Resource Utilization (ISRU) as well as customizability of performance for meeting specific mission needs. This paper describes implementation and direct measurement of this closed loop control mode as well as impulse measurement of multiple metals consistent with the aim of ISRU at NASA Glenn Research Center (GRC).

Electric Propulsion↗

NASA NTRSDate not supplied

Qualification of a Pulsed, Millinewton Class Metal Plasma Thruster for Broad Mission Applications

In the field of low power (<100W) electric propulsion, all thruster options demand significant trade-offs between operating parameters, reliability and scalable cost. With many systems on the market there are concerns with reliability, the need for extra considerations such as electron neutralizers for pure ion plumes, and the cost or craft compatibility of propellants. The Metal Plasma Thruster (MPT) is a new type of electric propulsion technology intended for low power applications. The system imparts momentum using inert, solid metal pucks as a propellant by using pulsed power to convert the metal into high velocity (~17km/s for Mo) jets of quasi-neutral plasma. The MPT technology does not require gas or liquid propellants, neutralizers, standby heaters, high voltage electronics, high electric or magnetic fields to operate. This comparatively simple pulsed operation is amenable to closed loop control, which provides for fine thrust control and S/C directed impulse on demand. Furthermore, the technology can use any metal as propellant, opening up unique opportunities for In-Situ Resource Utilization (ISRU) as well as customizability of performance for meeting specific mission needs. This paper describes implementation and direct measurement of this closed loop control mode as well as impulse measurement of multiple metals consistent with the aim of ISRU at NASA Glenn Research Center (GRC).

Electric Propulsion↗

NASA NTRSDate not supplied

Uncrewed Aerial System Traffic Management Beyond Visual Line of Sight Multi Operator Technology Assessment Simulation

UAS Traffic Management (UTM) is a rapidly evolving space with increasing demand for regulation surrounding more complex operations. Beyond visual line of sight (BVLOS) operations are among these complex operations. The NASA UTM BVLOS sub-project is focusing on enabling more routine BVLOS operations through data collection for support of standards formulation. The Multi Operator Technology Assessment (MOTA) simulation is one of these activities that collects data on BVLOS operations within the same geographical area while sharing operational intents through a USS. Data collected includes workload, situation awareness, and usability on nominal and off-nominal operations. Results of this study are intended to provide recommendations for standards as well as provide insight on improvements to the systems under test. NASA intends to incorporate those improvements into their operations to support and updated BVLOS waiver from the FAA’s Near-Term Approval Process (NTAP).

Bryan J Petty↗

NASA NTRSDate not supplied

Uncrewed Aerial System Traffic Management Beyond Visual Line of Sight Multi Operator Technology Assessment Simulation

UAS Traffic Management (UTM) is a rapidly evolving space with increasing demand for regulation surrounding more complex operations. Beyond visual line of sight (BVLOS) operations are among these complex operations. The NASA UTM BVLOS sub-project is focusing on enabling more routine BVLOS operations through data collection for support of standards formulation. The Multi Operator Technology Assessment (MOTA) simulation is one of these activities that collects data on BVLOS operations within the same geographical area while sharing operational intents through a USS. Data collected includes workload, situation awareness, and usability on nominal and off-nominal operations. Results of this study are intended to provide recommendations for standards as well as provide insight on improvements to the systems under test. NASA intends to incorporate those improvements into their operations to support and updated BVLOS waiver from the FAA’s Near-Term Approval Process (NTAP).

Bryan J Petty↗

NASA NTRS2016

Hybrid Electric Propulsion Technologies for Commercial Transports

NASA Aeronautics Research Mission Directorate has set strategic research thrusts to address the major drivers of aviation such as growth in demand for high-speed mobility, addressing global climate and capitalizing in the convergence of technological advances. Transitioning aviation to low carbon propulsion is one of the key strategic research thrust and drives the search for alternative and greener propulsion system for advanced aircraft configurations. This work requires multidisciplinary skills coming from multiple entities. The Hybrid Gas-Electric Subproject in the Advanced Air Transportation Project is energizing the transport class landscape by accepting the technical challenge of identifying and validating a transport class aircraft with net benefit from hybrid propulsion. This highly integrated aircraft of the future will only happen if airframe expertise from NASA Langley, modeling and simulation expertise from NASA Ames, propulsion expertise from NASA Glenn, and the flight research capabilities from NASA Armstrong are brought together to leverage the rich capabilities of U.S. Industry and Academia.

electric motor vehicles↗

NASA NTRS1998

Midcourse Space Experiment Data Certification and Technology Transfer

The University of Alabama in Huntsville contributes to the Technical Management of the Midcourse Space Experiment Program, to the Certification of the Level 2 data produced by the Midcourse Space Experiment's suite of in-orbit imaging radiometers, imaging spectro-radiometers and an interferometer and to the Transfer of the Midcourse Space Experiment Technology to other Government Programs. The Technical Management of the Midcourse Space Experiment Program is expected to continue through out the spacecraft's useful life time. The Transfer of Midcourse Space Experiment Technology to other government elements is expected to be on a demand basis by the United States Government and other organizations. The University, of Alabama Huntsville' contribution specifically supports the Principal Investigator's Executive Committee, the Deputy Principal Investigator for Data Certification and Technology Transfer team, the nine Ultraviolet Visible Imagers and Spectrographic Imagers (UVISI) and the Pointing and Alignment of all eleven of the science instruments. The science instruments effectively cover the 0.1 to 28 micron spectral region. The Midcourse Space Experiment spacecraft, launched April 24, 1996, is expected to have a 5 year useful lifetime. The cryogenically cooled IR sensor, SPIRIT III, performed through February, 1997 when its cryogen expired. A pre-launch, ground based calibration of the instruments provided a basis for the pre-launch certification of the Level 2 data base these instruments produce. With the spacecraft in-orbit the certification of the instrument's Level 2 data base was extended to the in-orbit environment.

Pollock, David B.↗

NASA NTRS1980

Regional price targets appropriate for advanced coal extraction

A methodology is presented for predicting coal prices in regional markets for the target time frames 1985 and 2000 that could subsequently be used to guide the development of an advanced coal extraction system. The model constructed is a supply and demand model that focuses on underground mining since the advanced technology is expected to be developed for these reserves by the target years. Coal reserve data and the cost of operating a mine are used to obtain the minimum acceptable selling price that would induce the producer to bring the mine into production. Based on this information, market supply curves can be generated. Demand by region is calculated based on an EEA methodology that emphasizes demand by electric utilities and demand by industry. The demand and supply curves are then used to obtain the price targets. The results show a growth in the size of the markets for compliance and low sulphur coal regions. A significant rise in the real price of coal is not expected even by the year 2000. The model predicts heavy reliance on mines with thick seams, larger block size and deep overburden.

Terasawa, K. L.↗

NASA NTRS2002

Advanced Engine Cycles Analyzed for Turbofans With Variable-Area Fan Nozzles Actuated by a Shape Memory Alloy

Advanced, large commercial turbofan engines using low-fan-pressure-ratio, very high bypass ratio thermodynamic cycles can offer significant fuel savings over engines currently in operation. Several technological challenges must be addressed, however, before these engines can be designed. To name a few, the high-diameter fans associated with these engines pose a significant packaging and aircraft installation challenge, and a large, heavy gearbox is often necessary to address the differences in ideal operating speeds between the fan and the low-pressure turbine. Also, the large nacelles contribute aerodynamic drag penalties and require long, heavy landing gear when mounted on conventional, low wing aircraft. Nevertheless, the reduced fuel consumption rates of these engines are a compelling economic incentive, and fans designed with low pressure ratios and low tip speeds offer attractive noise-reduction benefits. Another complication associated with low-pressure-ratio fans is their need for variable flow-path geometry. As the design fan pressure ratio is reduced below about 1.4, an operational disparity is set up in the fan between high and low flight speeds. In other words, between takeoff and cruise there is too large a swing in several key fan parameters-- such as speed, flow, and pressure--for a fan to accommodate. One solution to this problem is to make use of a variable-area fan nozzle (VAFN). However, conventional, hydraulically actuated variable nozzles have weight, cost, maintenance, and reliability issues that discourage their use with low-fan-pressure-ratio engine cycles. United Technologies Research, in cooperation with NASA, is developing a revolutionary, lightweight, and reliable shape memory alloy actuator system that can change the on-demand nozzle exit area by up to 20 percent. This "smart material" actuation technology, being studied under NASA's Ultra-Efficient Engine Technology (UEET) Program and Revolutionary Concepts in Aeronautics (RevCon) Program, has the potential to enable the next generation of efficient, quiet, very high bypass ratio turbofans. NASA Glenn Research Center's Propulsion Systems Analysis Office, along with NASA Langley Research Center's Systems Analysis Branch, conducted an independent analytical assessment of this new technology to provide strategic guidance to UEET and RevCon. A 2010-technology-level high-spool engine core was designed for this evaluation. Two families of low-spool components, one with and one without VAFN's, were designed to operate with the core. This "constant core" approach was used to hold most design parameters constant so that any performance differences between the VAFN and fixed nozzle cycles could be attributed to the VAFN technology alone. In this manner, the cycle design regimes that offer a performance payoff when VAFN's are used could be identified. The NASA analytical model of a performance-optimized VAFN turbofan with a fan pressure ratio of 1.28 is shown. Mission analyses of the engines were conducted using the notional, long-haul, advanced commercial twinjet shown. A high wing design was used to accommodate the large high-bypassratio engines. The mission fuel reduction benefit of very high bypass shape-memory-alloy VAFN aircraft was calculated to be 8.3 percent lower than a moderate bypass cycle using a conventional fixed nozzle. Shape-memory-alloy VAFN technology is currently under development in NASA's UEET and RevCon Programs.

Berton, Jeffrey J.↗

NASA NTRS2004

Thermal Control Technologies for Complex Spacecraft

Thermal control is a generic need for all spacecraft. In response to ever more demanding science and exploration requirements, spacecraft are becoming ever more complex, and hence their thermal control systems must evolve. This paper briefly discusses the process of technology development, the state-of-the-art in thermal control, recent experiences with on-orbit two-phase systems, and the emerging thermal control technologies to meet these evolving needs. Some "lessons learned" based on experience with on-orbit systems are also presented.

Swanson, Theodore D.↗

NASA NTRS1998

Affordable, Robust Ceramic Joining Technology (ARCJoinT)

Joining is recognized as one of the enabling technologies for the application of silicon carbide-based ceramic and composite components in a number of demanding and high temperature applications in aerospace and ground-based systems. An affordable, robust ceramic joining technology (ARCJoinT) for joining of silicon carbide-based ceramics and fiber reinforced composites has been developed. This technique is capable of producing joints with tailorable thickness and composition. A wide variety of silicon carbide-based ceramics and composites, in different shapes and sizes, have been joined using this technique. These joints maintain their mechanical strength up to 1350 C in air. This technology is suitable for the joining of large and complex shaped ceramic and composite components and with certain modifications, can be applied to repair ceramic components damaged in service.

Singh, M.↗

NASA NTRS1989

Cryogenic fluid management technology requirements for the Space Transfer Vehicle

An in-house study was performed to design a cryogenic Space Transfer Vehicle (STV) for the late 1990s that can evolve with the demanding mission requirements of the manned exploration initiatives. An assessment of cryogenic fluid management technology issues associated with the STV was performed to identify technology gaps and propose advanced development activities.

Cramer, John M.↗

NASA NTRS1990

Applying CLIPS to control of molecular beam epitaxy processing

A key element of U.S. industrial competitiveness in the 1990's will be the exploitation of advanced technologies which involve low-volume, high-profit manufacturing. The demands of such manufacture limit participation to a few major entities in the U.S. and elsewhere, and offset the lower manufacturing costs of other countries which have, for example, captured much of the consumer electronics market. One such technology is thin-film epitaxy, a technology which encompasses several techniques such as Molecular Beam Epitaxy (MBE), Chemical Beam Epitaxy (CBE), and Vapor-Phase Epitaxy (VPE). Molecular Beam Epitaxy (MBE) is a technology for creating a variety of electronic and electro-optical materials. Compared to standard microelectronic production techniques (including gaseous diffusion, ion implantation, and chemical vapor deposition), MBE is much more exact, though much slower. Although newer than the standard technologies, MBE is the technology of choice for fabrication of ultraprecise materials for cutting-edge microelectronic devices and for research into the properties of new materials.

Rabeau, Arthur A.↗