Search NASA⌕ Search

SEARCH · Search NASA

Results for “dendritic cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Preliminary investigation of a sealed, remotely activated silver-zinc battery

Methods necessary to provide a remotely activated, silver zinc battery capable of an extended activated stand while in a sealed condition were investigated. These requirements were to be accomplished in a battery package demonstrating an energy density of at least 35 watt hours per pound. Several methods of gas suppression were considered in view of the primary nature of this unit and utilized the electroplated dendritic zinc electrode. Amalgamation of the electrode provided the greatest suppression of gas at the zinc electrode. The approach to extending the activated stand capability of the remotely activated battery was through evaluation of three basic methods of remote, multi-cell activation; 1) the electrolyte manifold, 2) the gas manifold and 3) the individual cell. All three methods of activation can be incorporated into units which will meet the minimum energy density requirement.

Wheat, C. G.↗
DOE OSTI2021

High Depth‐of‐Discharge Zinc Rechargeability Enabled by a Self‐Assembled Polymeric Coating

Abstract Zinc has the potential for widespread use as an environmentally friendly and cost‐effective anode material pending the resolution of rechargeability issues caused by active material loss and shape change. Here, a self‐assembled Nafion‐coated Celgard 3501 (NC‐Celgard) separator is shown to enable unprecedented cycle life of a Zn anode in alkaline electrolyte at high depth‐of‐discharge (DOD Zn ). Using commercially relevant energy‐dense electrodes with high areal capacities of 60 mAh cm –2 , Zn–Ni cells tested at 20% DOD Zn cells achieve over 200 cycles while 50% DOD Zn cells achieve over 100 cycles before failure. The 20% and 50% DOD cells deliver an average of 132 and 180 Wh L –1 per cycle over their lifetime respectively. Rechargeability is attributed to the highly selective diffusion properties of the 300 nm thick negatively charged Nafion coating on the separator which prevents shorting by dendrites and inhibits redistribution of the active material. Crossover experiments show that the NC‐Celgard separator is practically impermeable to zincate ([Zn(OH) 4 ] 2– ), outperforming commercial Celgard, cellophane, Nafion 211 and 212 separators while still allowing hydroxide transport. This work demonstrates the efficacy of selective separators for increasing the cycle life of energy‐dense Zn electrodes without adding significant volume or complexity to the system.

Arnot, David J.↗
DOE OSTI2025

Industrializable interlayer with catalytic conversion of dead lithium for Ah–level Nickel–rich lithium metal batteries

The growth of lithium (Li) dendrites and the accumulation of dead Li (i.e., Li metal regions which are electronically disconnected from the current collector) significantly undermine the safety and performance of Li metal batteries. This study employs kilogram-scale atomic layer deposition technology to construct zinc oxide with a preferential (002) crystal orientation, which homogeneously forms on commercial carbon nanotube papers. Our approach emphasizes the importance of achieving a moderate Li adsorption energy and low Li migration energy barriers to suppress Li dendrite growth. In this work, we introduce the concept of "catalytic" effect for dead Li reconversion, as validated through time-of-flight secondary ion mass spectrometry, leading to a Li plating/stripping efficiency of 99.89%. The Ah-level Li metal pouch cells with high-nickel positive electrodes achieve a specific energy of 380 Wh kg -1 (based on the mass of the whole pouch cell) and demonstrate stable cycling under demanding conditions. Analysis of the cycled pouch cells confirms the structural integrity and provides insights into the mechanism of the dead Li "catalytic" conversion.

Shen, Huasen [Jianghan University, Wuhan (China)]↗
DOE OSTI2024

Magnetically oriented nanosheet interlayer for dynamic regeneration in lithium metal batteries

Lithium (Li) metal has been recognized as a promising anode to advance the energy density of current Li-based batteries. However, the growth of the solid–electrolyte interphase (SEI) layer and dendritic Li microstructure pose significant challenges for the long-term operation of Li metal batteries (LMBs). Herein, we propose the utilization of a suspension electrolyte with dispersed magnetically responsive nanosheets whose orientation can be manipulated by an external magnetic field during cell operation for realizing in situ regeneration in LMBs. The regeneration mechanism arises from the redistribution of the ion flux and the formation of an inorganic-rich SEI for uniform and compact Li deposition. With the magnetic-field-induced regeneration process, we show that a Li||Li symmetric cell stably operates for 350 h at 2 mA cm −2 and 2 mA h cm −2 , ~5 times that of the cell with the pristine electrolyte. Furthermore, the cycling stability can be significantly extended in the Li||NMC full cell of 3 mA h cm −2 , showing a capacity retention of 67% after 500 cycles at 1C. The dynamic Li metal regeneration demonstrated here could bring useful design considerations for reviving the operating cells for achieving high-energy, long-duration battery systems.

Ju, Zhengyu↗
DOE OSTI2021

Molecular Layer Deposition of Crosslinked Polymeric Lithicone for Superior Lithium Metal Anodes

In this work, we for the first time developed a novel lithium-containing crosslinked polymeric material, a lithicone that enables excellent protection effects over lithium (Li) metal anodes. This new lithicone was synthesized via an accurately controllable molecular layer deposition (MLD) process, in which lithium tert -butoxide (LTB) and glycerol (GL) were used as precursors. The resultant LiGL lithicone was analyzed using a suite of characterizations. Furthermore, we found that the LiGL thichicone could serve as an exceptional polymeric protection film over Li metal anodes. Our experimental data revealed that the Li electrodes coated by this LiGL lithicone can achieve a superior cycling stability, accounting for an extremely long cyclability of >13,600 Li-stripping/plating cycles and having no failures so far in Li/Li symmetric cells at a current density of 5 mA/cm 2 and an areal capacity of 1 mAh/cm 2 . We found that, with a sufficient protection by this LiGL coating, Li electrodes could realize long-term stable cyclability with little formation of Li dendrites and solid electrolyte interphase. This novel LiGL represents a facile and effective solution to the existing issues of Li anodes and potentially paves a technically feasible route for lithium metal batteries.

Meng, Xiangbo↗
DOE OSTI2020

Ultrahigh coulombic efficiency electrolyte enables Li||SPAN batteries with superior cycling performance

Raising the coulombic efficiency of lithium metal anode cycling is the deciding step in realizing long-life rechargeable lithium batteries. Here, we designed a highly concentrated salt/ether electrolyte diluted in a fluorinated ether: 1.8 M LiFSI in DEE/BTFE (diethyl ether/bis(2,2,2-trifluoroethyl)ether), which realized an average coulombic efficiency of 99.37% at 0.5 mA cm -2 and 1 mAh cm -2 for more than 900 cycles. This electrolyte also maintained a record coulombic efficiency of 98.7% at 10 mA cm -2 , indicative of its ability to provide fast-charging with high cathode loadings. Morphological studies reveal dense, dendrite free Li depositions after prolonged cycling, while surface analyses confirmed the formation of a robust LiF-rich SEI layer on the cycled Li surface. Moreover, we discovered that this ether-based electrolyte is highly compatible with the low-cost, high-capacity SPAN (Sulfurized polyacrylonitrile) cathode, where the constructed Li||SPAN cell exhibited reversible cathode capacity of 579 mAh g -1 and no capacity decay after 1200 cycles. A cell where a high areal loading SPAN electrode (>3.5 mAh cm -2 ) is paired with only onefold excess Li was constructed and cycled at 1.75 mA cm -2 , maintaining a coulombic efficiency of 99.30% for the lithium metal. Computational simulations revealed that at saturation, the Li-FSI complex forms contact ion pairs, with a first solvation shell comprising DEE molecules, and a second solvation shell with a mix of DEE/BTFE. This study provides a path to enable high energy density Li||SPAN batteries with stable cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Beyond the Polysulfide Shuttle and Lithium Dendrite Formation: Addressing the Sluggish Sulfur Redox Kinetics for Practical High-Energy Li-S Batteries

Electrolyte modulation simultaneously suppresses polysulfide the shuttle effect and lithium dendrite formation of lithium-sulfur (Li-S) batteries. However, the sluggish S redox kinetics, especially under high S loading and lean electrolyte operation, has been ignored, which dramatically limits the cycle life and energy density of practical Li-S pouch cells. In this work, we demonstrate that a rational combination of selenium doping, core-shell hollow host structure, and fluorinated ether electrolytes enables ultrastable Li stripping/plating and essentially no polysulfide shuttle as well as fast redox kinetics. Thus, high areal capacity (>4 mAh cm -2 ) with excellent cycle stability and Coulombic efficiency were both demonstrated in Li metal anode and thick S cathode (4.5 mg cm -2 ) with a low electrolyte/sulfur ratio (10 mu L mg(-1)). Overall, this research further demonstrates a durable Li-Se/S pouch cell with high specific capacity, validating the potential practical applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Digital light processing of porous LLZTO scaffolds for Li-garnet solid-state batteries

Li 7 La 3 Zr 2 O 12 (LLZO)-based solid-state electrolytes (SEs) are promising materials for next-generation solid-state batteries. In this work, digital light processing (DLP), an emerging additive manufacturing technology, is employed to produce porous Ta-doped LLZO (LLZTO) scaffolds. The self-standing scaffolds are 100 μm thick and have 40% porosity. The scaffolds demonstrate symmetric cell cycling stability exceeding 1,500 h at 0.1 mA/cm2 current density, with a capacity of 0.1 mAh/cm 2 (1 h for each half cycle). At higher current densities, reversible soft shorts frequently happen, while immediate hard shorts are prevented due to Li dendrite growth being hindered by the tortuous pore network. In addition to the cycling stability, the phase stability of LLZTO is investigated during the post-printing thermal process for printing resin removal. We discovered that the LLZTO partially decomposes into Li 2 Zr 2 O 7 and other impurity phases from 400°C to 800°C, but the pure LLZTO phase is restored upon the completion of resin removal beyond 800°C.

Li-metal anode↗
DOE OSTI2020

Thin Film Characterization on Cu/SnAg Solder Interface for 3D Packaging Technologies

Copper is a commonly used interconnect metal in microelectronic interconnects due to its exceptional electrical and thermal properties. Particularly in applications of the 2.5 and 3D integration, Cu is utilized in through-silicon-vias (TSVs) and flip chip interconnects between microelectronic chips for providing miniaturization, lower power and higher performance than current 2D packaging approaches. Furthermore, SnAg capped Cu pillars are a common high-density interconnect technology for flip chip bonding. For these interconnects, specific properties of the Cu surface, such as roughness and cleanliness, are an important factor in the process to ensure quality solder bumps. During electroplating, tight processing parameters must be met so that defects are avoided, and high bump uniformity is achieved. An understanding of the interactions at the solder and Cu pillar interface is needed, based on the electroplating parameters, to determine the best method for populating solder on the wafer surface. In this study, surface treatment techniques such as oxygen plasma cleaning were performed on the Cu surfaces and the SnAg plating chemistry for depositing the solder were evaluated through hull cell testing to qualitatively determine the range of current densities to investigate. It was observed that current density while plating played a large role in solder bump deposition morphology. At the higher current densities greater than 60 mA/cm 2 , bump height non-uniformity and dendritic growth are observed and at lower current densities, less than or equal to 60 mA/cm 2 , uniform, continuous bump height occurred.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Interface Pattern Selection in Directional Solidification

The central focus of this research is to establish key scientific concepts that govern the selection of cellular and dendritic patterns during the directional solidification of alloys. Ground-based studies have established that the conditions under which cellular and dendritic microstructures form are precisely where convection effects are dominant in bulk samples. Thus, experimental data can not be obtained terrestrially under pure diffusive regime. Furthermore, reliable theoretical models are not yet possible which can quantitatively incorporate fluid flow in the pattern selection criterion. Consequently, microgravity experiments on cellular and dendritic growth are designed to obtain benchmark data under diffusive growth conditions that can be quantitatively analyzed and compared with the rigorous theoretical model to establish the fundamental principles that govern the selection of specific microstructure and its length scales. In the cellular structure, different cells in an array are strongly coupled so that the cellular pattern evolution is controlled by complex interactions between thermal diffusion, solute diffusion and interface effects. These interactions give infinity of solutions, and the system selects only a narrow band of solutions. The aim of this investigation is to obtain benchmark data and develop a rigorous theoretical model that will allow us to quantitatively establish the physics of this selection process.

Trivedi, Rohit↗
DOE OSTI2025

A Universal Design of Lithium Anode via Dynamic Stability Strategy for Practical All‐Solid‐State Batteries

Abstract All‐solid‐state Li‐metal battery (ASSLB) chemistry with thin solid‐state electrolyte (SSE) membranes features high energy density and intrinsic safety but suffers from severe dendrite formation and poor interface contact during cycling, which hampers the practical application of rechargeable ASSLB. Here, we propose a universal design of thin Li‐metal anode (LMA) via a dynamic stability strategy to address these issues. The ultra‐thin LMA (20 μm) is in situ constructed with uniform highly Li‐ion conductive solid‐electrolyte interphase and composite‐polymer interphase (CPI) via electroplating process. As a result, the passivation layer with poor Li‐ion conduction on Li anode can be dissolved and small surface resistance can be achieved due to the good compatibility of CPI to SSEs. The cycling of Li symmetric cell with Li 6 PS 5 Cl thin film electrolyte (<100 μm) shows a high critical current density of >2.0 mA cm −2 with excellent cycling stability at 1.0 mA cm −2 . The ASSLBs paring with Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode demonstrated the feasibility of engineered LMA design by presenting good rate capability from 0.1 C to 1.0 C at room temperature, as well as long‐term cycling stability (81 % retention after 100 cycles). This work represents a general pathway to make thin dendrite‐free LMA available for high‐energy‐density ASSLBs.

Deng, Tao [Department of Chemical and Biomolecular↗
DOE OSTI2025

A Universal Design of Lithium Anode via Dynamic Stability Strategy for Practical All‐Solid‐State Batteries

Abstract All‐solid‐state Li‐metal battery (ASSLB) chemistry with thin solid‐state electrolyte (SSE) membranes features high energy density and intrinsic safety but suffers from severe dendrite formation and poor interface contact during cycling, which hampers the practical application of rechargeable ASSLB. Here, we propose a universal design of thin Li‐metal anode (LMA) via a dynamic stability strategy to address these issues. The ultra‐thin LMA (20 μm) is in situ constructed with uniform highly Li‐ion conductive solid‐electrolyte interphase and composite‐polymer interphase (CPI) via electroplating process. As a result, the passivation layer with poor Li‐ion conduction on Li anode can be dissolved and small surface resistance can be achieved due to the good compatibility of CPI to SSEs. The cycling of Li symmetric cell with Li 6 PS 5 Cl thin film electrolyte (<100 μm) shows a high critical current density of >2.0 mA cm −2 with excellent cycling stability at 1.0 mA cm −2 . The ASSLBs paring with Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode demonstrated the feasibility of engineered LMA design by presenting good rate capability from 0.1 C to 1.0 C at room temperature, as well as long‐term cycling stability (81 % retention after 100 cycles). This work represents a general pathway to make thin dendrite‐free LMA available for high‐energy‐density ASSLBs.

Deng, Tao [Department of Chemical and Biomolecular↗
DOE OSTI2022

Highly Reversible Sodium Metal Battery Anodes via Alloying Heterointerfaces

As a promising pathway toward low-cost, long-duration energy storage, rechargeable sodium batteries are of increasing interest. Batteries that incorporate metallic sodium as anode promise a high theoretical specific capacity of 1166 mAh g –1 , and low reduction potential of –2.71 V. The high reactivity and poor electrochemical reversibility of sodium anodes render sodium metal anode (SMA) cells among the most challenging for practical implementation. Here, the failure mechanisms of Na anodes are investigated and the authors report that loss of morphological control is not the fundamental cause of failure. Rather, it is the inherently poor anchoring/root structure of electrodeposited Na to the electrode substrate that leads to poor reversibility and cell failure. Poorly anchored Na deposits are prone to break away from the current collector, producing orphaning and poor anode utilization. Thin metallic coatings in a range of chemistries are proposed and evaluated as SMA substrates. Based on thermodynamic and ion transport considerations, such substrates undergo reversible alloying reactions with Na and are hypothesized to promote good root growth—regardless of the morphology. Among the various options, Au stands out for its ability to support long Na anode lifetime and high reversibility (Coulombic Efficiency > 98%), for coating thicknesses in the range of 10–1000 nm. Finally, as a first step toward evaluating practical utility of the anodes, their performance in Na||SPAN cells with N:P ratio close to 1:1 is evaluated.

25 ENERGY STORAGE↗
DOE OSTI2020

Electrochemical Healing of Dendrites in Garnet-Based Solid Electrolytes

Garnet oxides are a promising material family for solid-state batteries (SSBs). Dendrite formation in solid electrolytes critically limits the applicability of SSBs because of limiting Coulombic efficiency and power capability. In this study, the authors report operando electrochemical healing of dendrites in a garnet-based solid electrolyte (SE). Dendrites were deliberately formed at high operational current density (2 mA cm –2 ) beyond the critical current density (0.55 mA cm –2 ) of the used garnet SE. Electrochemical impedance spectroscopy and scanning electron microscopy were used to confirm dendrite growth in the SE. Dendrites were subsequently healed electrochemically via plating and stripping at 20 and 1 μA cm –2 current densities. Removal of dendrites was shown by an increase in bulk and interfacial resistance and a progressive increase in polarization during galvanostatic plating and stripping. High local current density at the dendrite tips was identified as the mechanism for preferentially removing dendrites electrochemically. The dendrite detection and healing methods discussed here are crucial for extending the life of SSBs.

25 ENERGY STORAGE↗
DOE OSTI2024

A Self-Healing, Flowable, Yet Solid Electrolyte Suppresses Li-Metal Morphological Instabilities

In this article, lithium metal (Li 0 ) solid-state batteries encounter implementation challenges due to dendrite formation, side reactions, and movement of the electrode–electrolyte interface in cycling. Notably, voids and cracks formed during battery fabrication/operation are hot spots for failure. Here, a self-healing, flowable yet solid electrolyte composed of mobile ceramic crystals embedded in a reconfigurable polymer network is reported. This electrolyte can auto-repair voids and cracks through a two-step self-healing process that occurs at a fast rate of 5.6 µm h -1 . A dynamical phase diagram is generated, showing the material can switch between liquid and solid forms in response to external strain rates. The flowability of the electrolyte allows it to accommodate the electrode volume change during Li 0 stripping. Simultaneously, the electrolyte maintains a solid form with high tensile strength (0.28 MPa), facilitating the regulation of mossy Li 0 deposition. The chemistries and kinetics are studied by operando synchrotron X-ray and in situ transmission electron microscopy (TEM). Solid-state NMR reveals a dual-phase ion conduction pathway and rapid Li + diffusion through the stable polymer-ceramic interphase. This designed electrolyte exhibits extended cycling life in Li 0 –Li 0 cells, reaching 12 000 h at 0.2 mA cm -2 and 5000 h at 0.5 mA cm -2 . Furthermore, owing to its high critical current density of 9 mA cm -2 , the Li 0 –LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) full cell demonstrates stable cycling at 5 mA cm -2 for 1100 cycles, retaining 88% of its capacity, even under near-zero stack pressure conditions.

25 ENERGY STORAGE↗
DOE OSTI2020

The electrolyte comprising more robust water and superhalides transforms Zn-metal anode reversibly and dendrite-free

A great challenge for all aqueous batteries, including Zn-metal batteries, is the parasitic hydrogen evolution reaction on the low-potential anode. Herein, we report the formula of a highly concentrated aqueous electrolyte that mitigates hydrogen evolution by transforming water molecules more inert. The electrolyte comprises primarily ZnCl 2 and LiCl as an additive, both of which are inexpensive salts. The O–H covalent bonds in water get strengthened in a chemical environment that has fewer hydrogen bonding interactions and a greater number of Zn–Cl superhalides, as suggested by integrated characterization and simulation. As a result, the average Coulombic efficiency of zinc-metal anode is raised to an unprecedented >99.7% at 1 mA cm –2 . In the new electrolyte, the plating/stripping processes leave the zinc-metal anode dendrite-free, and the zinc-metal anode delivers stable plating/stripping cycles for 4000 hours with an areal capacity of 4 mAh cm –2 at 2 mA cm –2 . Furthermore, the high Coulombic efficiency of zinc-metal anode in the ZnCl 2 -LiCl mixture electrolyte is demonstrated in full cells with a limited anode. The V 2 O 5 ·H 2 O| |Zn full cell with an N/P mass ratio of 1.2 delivers a stable life of more than 2500 cycles, and the LiMn 2 O 4 | |Zn hybrid cell with an N/P mass ratio of 0.6 exhibits 1500 cycles in its stable life.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

An Inorganic‐Rich Solid Electrolyte Interphase for Advanced Lithium‐Metal Batteries in Carbonate Electrolytes

Abstract In carbonate electrolytes, the organic–inorganic solid electrolyte interphase (SEI) formed on the Li‐metal anode surface is strongly bonded to Li and experiences the same volume change as Li, thus it undergoes continuous cracking/reformation during plating/stripping cycles. Here, an inorganic‐rich SEI is designed on a Li‐metal surface to reduce its bonding energy with Li metal by dissolving 4 m concentrated LiNO 3 in dimethyl sulfoxide (DMSO) as an additive for a fluoroethylene‐carbonate (FEC)‐based electrolyte. Due to the aggregate structure of NO 3 − ions and their participation in the primary Li + solvation sheath, abundant Li 2 O, Li 3 N, and LiN x O y grains are formed in the resulting SEI, in addition to the uniform LiF distribution from the reduction of PF 6 − ions. The weak bonding of the SEI (high interface energy) to Li can effectively promote Li diffusion along the SEI/Li interface and prevent Li dendrite penetration into the SEI. As a result, our designed carbonate electrolyte enables a Li anode to achieve a high Li plating/stripping Coulombic efficiency of 99.55 % (1 mA cm −2 , 1.0 mAh cm −2 ) and the electrolyte also enables a Li||LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC811) full cell (2.5 mAh cm −2 ) to retain 75 % of its initial capacity after 200 cycles with an outstanding CE of 99.83 %.

Liu, Sufu↗