Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffractive production”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Early age hydration behavior of portland cement-based binders incorporating fly ash contaminated with flue gas desulfurization products

Fly ash co-mingled with flue gas desulfurization (FGD) products are currently discarded as off-specification materials based on their high SO3 content. However, previous studies have shown that performance of these fly ashes varies significantly based on FGD product type and as such they may be viable for use in low-CO2 concrete as supplementary cementitious materials (SCMs). In this study, fly ashes with three different types of FGD products including calcium sulfite hemihydrate, calcium sulfate (with some unreacted lime), and sodium sulfate (with some unreacted sodium carbonate) were evaluated. The early age hydration behavior in blended cementitious systems at 20% cement replacement level was studied using Vicat setting time tests, isothermal calorimetry, in-situ quantitative X-ray diffraction, and pore solution analysis. The cause of the setting time retardation and flash setting observed in fly ashes with calcium sulfite hemihydrate and sodium carbonate, respectively, were identified and suitable beneficiation options were suggested for the valorized use of these materials in low-CO 2 concrete.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Actinide arene-metalates: ion pairing effects on the electronic structure of unsupported uranium–arenide sandwich complexes

Addition of [UI 2 (THF) 3 (μ-OMe)] 2 ·THF (2·THF) to THF solutions containing 6 equiv. of K[C 14 H 10 ] generates the heteroleptic dimeric complexes [K(18-crown-6)(THF) 2 ] 2 [U(η 6 -C 14 H 10 )(η 4 -C 14 H 10 )(μ-OMe)] 2 ·4THF (1 18C6 ·4THF) and {[K(THF) 3 ][U(η 6 -C 14 H 10 )(η 4 -C 14 H 10 )(μ-OMe)]} 2 (1 THF ) upon crystallization of the products in THF in the presence or absence of 18-crown-6, respectively. Both 1 18C6 ·4THF and 1 THF are thermally stable in the solid-state at room temperature; however, after crystallization, they become insoluble in THF or DME solutions and instead gradually decompose upon standing. X-ray diffraction analysis reveals 1 18C6 ·4THF and 1 THF to be structurally similar, possessing uranium centres sandwiched between bent anthracenide ligands of mixed tetrahapto and hexahapto ligation modes. Yet, the two complexes are distinguished by the close contact potassium-arenide ion pairing that is seen in 1 THF but absent in 1 18C6 ·4THF, which is observed to have a significant effect on the electronic characteristics of the two complexes. Structural analysis, SQUID magnetometry data, XANES spectral characterization, and computational analyses are generally consistent with U(IV) formal assignments for the metal centres in both 1 18C6 ·4THF and 1 THF , though noticeable differences are detected between the two species. For instance, the effective magnetic moment of 1 THF (3.74 μ B ) is significantly lower than that of 1 18C6 ·4THF (4.40 μ B ) at 300 K. Furthermore, the XANES data shows the U L III -edge absorption energy for 1 THF to be 0.9 eV higher than that of 1 18C6 ·4THF, suggestive of more oxidized metal centres in the former. Of note, CASSCF calculations on the model complex {[U(η 6 -C 14 H 10 )(η 4 -C 14 H 10 )(μ-OMe)] 2 } 2– (1*) shows highly polarized uranium–arenide interactions defined by π-type bonds where the metal contributions are primarily comprised by the 6d-orbitals (7.3 ± 0.6%) with minor participation from the 5f-orbitals (1.5 ± 0.5%). These unique complexes provide new insights into actinide–arenide bonding interactions and show the sensitivity of the electronic structures of the uranium atoms to coordination sphere effects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Combined effect of NaAlO2 and NaOH on the early age hydration of Portland cement with a high concentration of borate solution

The early age hydration of ordinary Portland cement in 5 M borate solution, with or without the addition of NaAlO{sub 2} and/or NaOH, was investigated. Hydration was measured using calorimetry, X-ray diffraction, thermogravimetric analysis, {sup 11}B and {sup 27}Al magic angle spinning NMR analysis, and scanning transmission electron microscopy. The purpose of this study was to reveal the mechanisms behind the retardation caused by a high concentration borate solution and the restoration of hydration through the combined addition of NaOH and NaAlO{sub 2}. Amorphous ulexite, which formed on the surface of the cement particles and prevented the further dissolution of anhydrous phases, was identified as the retardation product. The mechanism of the combined addition of NaAlO{sub 2} and NaOH in overcoming retardation was to transform amorphous ulexite into B-AFt and gowerite (CaB{sub 6}O{sub 10}·5H{sub 2}O). Formation of gowerite is favorable because of the much higher boron immobilization capacity in weight percentage, comparing to usual boron-containing phases reported previously.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Chemical compatibility of hollow ceramic cenospheres as thermal insulation for high-temperature thermal energy storage applications with molten nitrate salt

An effective insulation material that is both thermally and chemically stable in molten salts could transform the design of molten-salt-based thermal energy storage (TES) tanks. Most current molten salt TES tanks hold the metallic tank structure in direct contact with hot salt inventory, a design which leads to thermal expansion of the tank and triggers stresses that can lead to thermomechanical failures. With an internal insulation to lower the temperature at the tank structure, the extent of thermal expansion can be reduced, thereby reducing expansion-induced stresses and allowing for consideration of lower-cost tank structure materials. Conventional insulation materials are either 1) too porous and allow molten salts to permeate into the matrix, which significantly increases the thermal conductivity or 2) too dense and have a thermal conductivity that cannot provide sufficient thermal insulation. This paper presents an alternative thermal insulation concept using cenospheres which have an alumino-silicate structure. The cost analysis suggests that the low-density cenospheres can be one of the cheapest materials to provide cost-effective thermal insulation. The chemical compatibility of cenospheres is investigated in molten 60 wt% NaNO3/40 wt% KNO3 salt which is close to industrial-grade Solar Salt. This paper shows that diffusion of the sodium and potassium cations from the salt into the cenospheres occurs based on weight analysis, energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy. The cation diffusion breaks the bridging oxygen bonds and causes volume expansion of the microstructure which is responsible for the failure of the cenosphere particles. The chemical composition of the cenospheres is found to affect their compatibility with molten nitrate salt. A cenosphere product with low iron content showed the best compatibility with an average survival rate of 77.9% +/- 9.8% after 7 days of immersion in the molten nitrate salt. While even the low-iron cenospheres appear to require protection from direct molten salt contact, their slow degradation rate, closed-cell porosity, and low cost hold potential for effective use as internal tank insulation.

14 SOLAR ENERGY↗
DOE OSTI2025

Intermolecular Interactions in Direct Air Capture Materials: Insights from Charge Density Analysis

Direct air capture (DAC) materials enable the removal of CO 2 from the atmosphere, but improving their efficiency requires a detailed understanding of the intermolecular interactions that govern CO 2 sorption and release. Here, we present an experimental electron density study of methylglyoxal-bis(iminoguanidine) (MGBIG), a promising DAC material, using high-resolution X-ray and neutron diffraction data combined with quantum crystallographic analysis. This approach bridges theoretical and experimental data by quantifying electron density distributions and revealing how hydrogen bonds stabilize CO 2 -derived carbonate phases and may influence the desorption behavior. We identify distinct hydrogen-bonding environments in two crystalline carbonate phases: P1, a transient kinetic product, and P3, a thermodynamically stable phase. Multipolar refinement and electrostatic potential and multipole moment calculations precisely map electron density distributions, revealing key hydrogen bonds involved in CO 2 capture. Topological analysis of electron density highlights a cooperative hydrogen-bonding network in the thermodynamically favored P3 phase, where enhanced electron density delocalization and water-mediated interactions contribute to a more stable lattice. Energetic analyses confirm that stronger hydrogen bonding networks enhance the stability of P3 with a binding energy of −607.0 kJ/mol and greater lattice stability (−847.3 kJ/mol) compared to P1 (−302.5 and −571.0 kJ/mol, respectively). Electrostatic potential maps further illustrate polarization patterns that may influence the stability of the binding of CO 2 and release conditions. These findings establish a direct experimental framework for linking electron density distributions to intermolecular interactions in DAC materials, providing a rational design strategy for optimizing sorbents with improved CO 2 capture efficiency and reduced energy demands.

Electron density↗
DOE OSTI2022

Models to Incorporate Reaction Mechanisms into DG-OSPREY: Fixed-Bed Simulations for Organic Iodides Capture Using Ag 0 Z

As one of the most potent radioisotopes released during spent nuclear fuel reprocessing, 129 I is strictly regulated and must be removed before discharge. Organic iodides (primarily alkyl iodides with different chain lengths, i.e., CH 3 I, C 4 H 9 I, and C 12 H 25 I) comprise ~2% of the total iodine in the reprocessing off-gases and are primarily present in vessel off-gas (VOG). Reduced silver mordenite (Ag 0 Z) is predominantly considered for the removal of radioiodine; however, its capture performance and underlying interaction processes with long-chain organic iodides are not fully understood. Two major tasks were accomplished in this study. First, to improve upon the previous experimental studies where Ag 0 Z was used to capture CH 3 I, C 4 H 9 I, and C 12 H 25 I at different concentrations, we comprehensively investigated the corresponding capture mechanisms by characterizing fully loaded Ag 0 Z samples. Second, computational codes were implemented to perform fixed-bed simulations that account for transport and reaction mechanisms. Scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), powder X-ray diffraction (PXRD), UV-visible diffuse reflectance spectroscopy (UV-vis DRS), and thermogravimetric analysis (TGA) were conducted on Ag 0 Z samples that are saturated with I 2 , CH 3 I, C 4 H 9 I, and C 12 H 25 I), respectively. Results indicate that AgI is the predominant adsorption product regardless of the adsorbed iodine species, yet alkyl iodides with different carbon chain lengths may have different compositions of α- and γ-AgI. Synchrotron pair distribution function (PDF) measurements and TGA coupled with a Fourier transformed infrared detector (TGA FTIR) have been performed, and experimental data are currently analyzed. Results are expected to provide further insights into the adsorption mechanisms. The fixed-bed capture performance for CH 3 I was successfully simulated by solving mathematical equations that describe the underlying transport processes and adsorption reactions. The computational framework, Catalytic After Treatment System (CATS), that was originated in our research group, was used to solve the governing equations. Kinetic parameters, including the pore diffusivity and reaction rate constant were obtained by optimization techniques using data from thin-bed experiments performed at Oak Ridge National Laboratory. The performance of a deep bed predicted using the optimized parameters showed promising agreement with the experimental data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Influence of oxygen on the optical and electrical properties of magnetron-sputtered indium tin oxide thin films at ambient temperature

Indium Tin Oxide (ITO) thin films are commonly used as transparent conductive layers in the production of solar cells. ITO films are typically heat-treated at temperatures exceeding 200 °C after magnetron sputtering to optimize the physical, optical, and electrical characteristics for photovoltaic devices. Here, this high temperature heating procedure greatly limits the use of potential substrates, particularly those comprised of low-temperature-rated polymers. Herein, we examine the physical, optical, and electrical transport effects of oxygen:argon plasmas during radio frequency magnetron sputtering of ITO on glass and flexible polymer surfaces without subsequent heat treatment. ITO thin films were characterized via sheet resistance testing, UV-Vis spectroscopy, X-ray diffraction, and scanning electron microscopy imaging. Sheet resistance measurements revealed an increase in surface resistance with increasing oxygen concentration during sputtering. UV-Vis optical transmittance measurements demonstrated an improvement in optical transmittance with an increase in oxygen concentration reaching a maximum transmittance at an oxygen concentration of 1-2 %. Most importantly, it was discovered that producing bilayers of ITO with pure argon sputtered plasmas followed by oxygen:argon plasmas produced ITO thin films with suitable resistance and transmittance without the need for high temperature post annealing. These results highlight a methodology for the deposition of ITO thin films on temperature sensitive substrates for flexible photovoltaics and low-cost module production.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of tension during sulfonation stabilization for UHMWPE-derived carbon fibers

Polyethylene is a promising low-cost alternative precursor material for carbon fiber production, but it has yet to show mechanical properties near or surpassing polyacrylonitrile-derived carbon fibers. The high molecular weight and order of ultra-high molecular weight polyethylene (UHMWPE) may offer a pathway to realizing this promise by enabling long-range graphitic structure formation and superior mechanical properties. The tension applied during the precursor stabilization process is crucial to maintaining the shape of the fibers during the conversion process, but no published study has yet probed the relationship between sulfonation tension and carbon fiber microstructure and mechanical properties. In this work, a logarithmic sweep of tensile stress was applied to UHMWPE fibers during the stabilization process followed by carbonization. Increasing tension significantly reduced fiber shrinkage, resulted in straighter fibers with less severe kink bands, and greatly improved the mechanical properties of the fibers. Raman spectroscopy and X-ray diffraction revealed that in all cases the carbon fibers were largely amorphous, but increasing tension resulted in increased size and alignment of the turbostratic crystallites with the fiber axis. Large voids were present in the sample fibers, so the Griffith-Irwin relation was employed to predict the potential ultimate tensile strength of the fibers with voids reduced to sizes comparable to commercially produced fibers. Furthermore, this work demonstrates the importance of tension applied during the stabilization of polyethylene fibers for carbon fiber production and establishes a framework for achieving high mechanical properties from these precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Progress in Near-Equilibrium Ammonothermal (NEAT) Growth of GaN Substrates for GaN-on-GaN Semiconductor Devices

This paper reviews the near-equilibrium ammonothermal (NEAT) growth of bulk gallium nitride (GaN) crystals and reports the evaluation of 2″ GaN substrates and 100 mmbulk GaN crystal grown in our pilot production reactor. Recent progress in oxygen reduction enabled growing NEAT GaN substrates with lower residual oxygen, coloration, and optical absorption. The oxygen concentration was approximately 2 × 1018 cm−2, and the optical absorption coefficient was 1.3 cm−1 at 450 nm. Maps of full-width half maximum (FWHM) of X-ray diffraction rocking curveswere generated for grown crystals and finished wafers. The X-ray rocking curve maps confirmed high-quality and uniform microstructure across the entire surface of the bulk crystals and substrates. The average FWHM of the 50 best bulk crystals from the recent batch was 28 ± 4 arcsec for the 002 diffraction and 34 ± 5 arcsec for the 201 diffraction, with an average radius of curvature of 20 m. X-ray topography measured on both sides of the bulk crystals implied that the density of dislocations wasreduced by one order of magnitude during the NEAT growth. A typical NEAT GaN substrate shows dislocation density of about 2 × 105 cm−2.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Direct Conversion of Methane to Ethylene and Acetylene over an Iron-Based Metal–Organic Framework

Conversion of methane (CH 4 ) to ethylene (C 2 H 4 ) and/or acetylene (C 2 H 2 ) enables routes to a wide range of products directly from natural gas. However, high reaction temperatures and pressures are often required to activate and convert CH 4 controllably, and separating C 2+ products from unreacted CH 4 can be challenging. Here, we report the direct conversion of CH 4 to C 2 H 4 and C 2 H 2 driven by non-thermal plasma under ambient (25 °C and 1 atm) and flow conditions over a metal–organic framework material, MFM-300(Fe). The selectivity for the formation of C 2 H 4 and C 2 H 2 reaches 96% with a high time yield of 334 μmol g cat –1 h –1 . At a conversion of 10%, the selectivity to C 2+ hydrocarbons and time yield exceed 98% and 2056 μmol g cat –1 h –1 , respectively, representing a new benchmark for conversion of CH 4 . In situ neutron powder diffraction, inelastic neutron scattering and solid-state nuclear magnetic resonance, electron paramagnetic resonance (EPR), and diffuse reflectance infrared Fourier transform spectroscopies, coupled with modeling studies, reveal the crucial role of Fe–O(H)–Fe sites in activating CH 4 and stabilizing reaction intermediates via the formation of an Fe–O(CH 3 )–Fe adduct. In addition, a cascade fixed-bed system has been developed to achieve online separation of C 2 H 4 and C 2 H 2 from unreacted CH 4 for direct use. Integrating the processes of CH 4 activation, conversion, and product separation within one system opens a new avenue for natural gas utility, bridging the gap between fundamental studies and practical applications in this area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Activated carbon supported Ni, Fe, and bimetallic NiFe catalysts for CO x -free H 2 production by microwave methane pyrolysis

The goal of this study was to test the effect of metal-impregnated carbon-based catalysts on the conversion of methane to hydrogen gas and solid carbon using microwave reactor technology. Monometallic and bimetallic catalysts on activated carbon supports (Ni/AC, Fe/AC, Ni-Fe/AC) are compared during methane pyrolysis testing. Catalytic methane pyrolysis was carried out in a microwave reactor at reaction temperatures of 600 °C and 800 °C. For comparison, one of the catalysts (Ni-Fe/AC) was tested in a conventionally heated reactor at 800 °C. The prepared catalysts were characterized by X-ray diffraction (XRD), while post-reaction catalysts were characterized by XRD and SEM. During reaction testing, the monometallic Ni/AC catalyst exhibited the best catalytic activity (CH 4 conversion: 46.0 and H 2 yield: 46.9%) when reacted in the microwave reactor, however, it suffered from rapid deactivation from carbon deposition (carbon yield: 0.39 gC/g catalyst). The bimetallic Ni-Fe/AC catalyst was slightly less active (CH 4 conversion: 36.9 and H 2 yield: 40.5%) but it was more resistant to carbon formation (carbon yield: 0.27 gC/g catalyst) suggesting it may have greater long-term stability. The Ni-Fe/AC catalyst was also the most energy efficient as it required the least microwave power to maintain the 800 °C reaction temperature compared to the other catalysts tested. Methane conversion of the bimetallic Ni-Fe/AC at 800 °C under microwave irradiation was three times the conversion under conventional heating at the same reaction temperature. Finally, this work demonstrates the use of microwave-specific catalysts for catalytic methane pyrolysis in a microwave reactor, and can be used as a foundation for further methane pyrolysis process and catalyst optimization for CO x -free H 2 production.

08 HYDROGEN↗
DOE OSTI2021

Structure of the pellet-cladding interaction layer of a high-burnup Zr-Nb-O nuclear fuel cladding

Here, structure of the pellet/cladding-interaction (PCI) layer of a high-burnup nuclear fuel with niobium-bearing cladding was investigated using modern transmission electron microscopy (TEM) techniques. Morphology of the PCI consisted of uniform zirconia layer on the cladding side and finger-like features towards to the ceramic fuel. The PCI layer showed a complex microstructure that constitutes three distinct zirconia layers formed by two zirconia phases. From cladding to fuel, monoclinic, tetragonal, and another tetragonal phase were determined via TEM diffraction patterns and precession electron diffraction (PED) using ASTAR microscopy platform (AMP). Characterizations showed that monoclinic and tetragonal phases close to the cladding were crack-free, but the tetragonal layer adjacent to the fuel contained cracks and pores. Presence of the monoclinic layer suggested that its formation involved the gaseous diffusion of oxygen below threshold dose of fission product damage before the fuel/cladding contact occurred. Furthermore, high-resolution TEM revealed compound phase of (U,Zr)O 2 at fringes of zirconia fingers on the fuel side.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Simultaneous ambient pressure x-ray photoelectron spectroscopy and grazing incidence x-ray scattering in gas environments

We have developed an experimental system to simultaneously measure surface structure, morphology, composition, chemical state, and chemical activity for samples in gas phase environments. This is accomplished by simultaneously measuring x-ray photoelectron spectroscopy (XPS) and grazing incidence x-ray scattering in gas pressures as high as the multi-Torr regime while also recording mass spectrometry. Scattering patterns reflect near-surface sample structures from the nano-scale to the meso-scale, and the grazing incidence geometry provides tunable depth sensitivity of structural measurements. Scattered x rays are detected across a broad range of angles using a newly designed pivoting-UHV-manipulator for detector positioning. At the same time, XPS and mass spectrometry can be measured, all from the same sample spot and under ambient conditions. To demonstrate the capabilities of this system, we measured the chemical state, composition, and structure of Ag-behenate on a Si(001) wafer in vacuum and in O 2 atmosphere at various temperatures. These simultaneous structural, chemical, and gas phase product probes enable detailed insights into the interplay between the structure and chemical state for samples in gas phase environments. The compact size of our pivoting-UHV-manipulator makes it possible to retrofit this technique into existing spectroscopic instruments installed at synchrotron beamlines. Because many synchrotron facilities are planning or undergoing upgrades to diffraction limited storage rings with transversely coherent beams, a newly emerging set of coherent x-ray scattering experiments can greatly benefit from the concepts we present here.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Enhanced alcohol production over binary Mo/Co carbide catalysts in syngas conversion

Recently metal carbide catalysts have attracted attention as alternatives to pure metals for the conversion of syngas to higher oxygenates, a process which could enable the sustainable production of fuels, polymers, and chemicals. Although Mo and Co carbides have both shown promise for higher oxygenate production, they have not achieved the requisite activity and selectivity for practical implementation. In this work we synthesize and characterize a binary Mo and Co carbide catalyst that exhibits improved activity and oxygenate selectivity relative to either pure metal carbide. In this work, we apply a combination of advanced electron microscopy and X-ray diffraction to show that the binary Mo/Co carbide catalyst forms uniformly mixed amorphous nanoparticles. Through in situ X-ray absorption spectroscopy studies, we determine that the structure of the mixed metal carbide catalyst under reaction conditions consists of both carbidic and bimetallic components. By testing the catalytic properties of a series of Mo/Co carbide catalysts prepared by different synthesis methods, we find that the Mo and Co sites must be in close contact to achieve improved syngas conversion to higher alcohols. Through in situ DRIFTS measurements, both Mo and Co atoms at the surface of the catalyst are identified as adsorption sites for reactive species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Ultrafast disruptive probing: Simultaneously keeping track of tens of reaction pathways

Ultrafast science depends on different implementations of the well-known pump–probe method. Here, we provide a formal description of ultrafast disruptive probing, a method in which the probe pulse disrupts a transient species that may be a metastable ion or a transient state of matter. Disruptive probing has the advantage of allowing for simultaneous tracking of the yield of tens of different processes. Our presentation includes a numerical model and experimental data on multiple products resulting from the strong-field ionization of two different molecules, partially deuterated methanol and norbornene. The correlated enhancement and depletion signals between all the different fragmentation channels offer comprehensive information on photochemical reaction pathways. In combination with ion imaging and/or coincidence momentum imaging or as complementary to atom-specific probing or ultrafast diffraction methods, disruptive probing is a particularly powerful tool for the study of strong-field laser–matter interactions.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Stress-sensitivity of fracture conductivity of Tuscaloosa Marine Shale cores

Production decline from wells producing from shale rocks is typically quite rapid. One possible factor responsible for such decline is loss in fracture conductivity. This is true in the case of the Tuscaloosa Marine shale reservoir. In this work, the stress-dependent fracture conductivity of TMS core samples is investigated using five propped cores under varying stress conditions. In addition, the effects of static rock mechanical properties and rock mineralogy on conductivity decline are investigated. The mineralogy of each core sample was determined by X-ray Diffraction analysis. Fracture conductivity was measured using a Hassler-type pressure core holder with a pressure rating of 15,000 psi (103.42 MPa). Estimated rock mechanical properties showed that shale anisotropy could affect fracture conductivity. The time decline in conductivity revealed two possible decline trends, a) decline from the reduction in induced fracture width, and b) decline from the healing of developed micro-cracks. An exponential decline in fracture conductivity with increasing confinement pressure was observed with an average decline rate constant of 3.15 x 10 -10 mPa -1 . While rock mineralogy did not have any clear relationship with conductivity decline, the effects of rock mechanical properties were only important at 10.34 MPa confinement pressure and above. The observation showed that a high Young's modulus correlate to high conductivity, whereas a high Poisson's ratio correlate to low conductivity. This study provides useful observations for optimizing fracture design to enhance well productivity in the TMS.

02 PETROLEUM↗
DOE OSTI2025

Reducing waste of the hydride-dehydride process for U-6 wt% Nb spherical powders through lower impact and targeted milling

The breakdown of solid metal into powder during the hydride-dehydride process is commercially important for the formation of titanium and other metal powders. Typically, the milling of the brittle hydride powder occurs in a ball mill, where milling media impacts powder particles to break them down. The milling media can impact particles that are larger than desired, as desired, or smaller than desired, indiscriminately making all particles smaller. In this work, we investigate how to minimize waste powder production during milling using two different milling methods, planetary ball milling and milling in a sieve shaker (sieve-milling). Both processes yielded similar amounts of 20–75 μm diameter powder (the target size range); however, sieve-milling generated a significantly smaller amount of undersized waste powder. The powders were characterized by X-ray diffraction, SEM/STEM, and magnetic susceptibility. Several differences between ball milling and sieve-milling processes are discussed. We then conclude that the decreased yield of undersized powder in sieve-milling was due to a combination of lower impact energy in sieve-milling, unreacted metallic cores in the hydride flakes, and the ability to mill target particle sizes during sieve-milling. While these results are from the milling of brittle hydride powder, similar methods may be applicable to other brittle powders, including ceramics or salts.

Chemistry↗
DOE OSTI2021

Tandem Catalytic Antioxidant Nanoparticles Comprising Cerium Carbonate and Photoactive Metal Oxides

While photoactive metal oxides such as TiO 2 find widespread use in paints and coatings as well as cosmetics and suncare products, they also generate reactive oxygen species (ROS), which degrade materials and are associated with human-health pathologies. Here, we demonstrate a robust and potent catalytic antioxidant consisting of earth-abundant cerium carbonate nanoparticles and micron-size Ce 2 (CO 3 ) 3 . 8H 2 O, which are characterized by powder X-ray diffraction and scanning nanobeam electron diffraction. When dispersed with photoactive metal oxides, these cerium carbonate catalysts decrease the photodecomposition rate of organic dyes and commercial pigment colorants in aqueous media by up to 820-fold, as well as in acrylic coatings. X-ray photoelectron spectroscopy and kinetic experiments support the same tandem catalysis mechanism of photoprotection when using both micron-size Ce 2 (CO 3 ) 3 . 8H 2 O and cerium carbonate nanoparticles. This mechanism involves ROS disproportionation (catalyzed by cerium carbonate) and H 2 O 2 decomposition (partially catalyzed by TiO 2 ) pathways, both of which cerium carbonate also catalyzes on its own, crudely mimicking the function of the cascade system of superoxide dismutase and catalase enzymes. When cerium carbonate nanoparticles were dispersed at 2 wt % in polymethylmethacrylate, the transparency of the polymer film was preserved and the photo-oxidative degradation of the polymer was prevented following UV irradiation at 254 nm, which otherwise resulted in the loss of optical properties and hydroxylation as characterized by ATR-FTIR spectroscopy, in the control polymer lacking cerium carbonate. Similar observations were made regarding color preservation in paint films comprising dye and insoluble commercial colorant pigments. The material chemistry associated with this photoprotection catalysis is subtle and emphasizes the importance of both Ce(III) and carbonate together, as both CePO 4 and Na 2 CO 3 are inactive. In conclusion, this emphasis is also apparent in comparisons of photoprotection catalysis with previously reported cerium oxide nanoparticles, which are significantly less active compared with Ce 2 (CO 3 ) 3 . 8H 2 O under the same conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗