Search NASA⌕ Search

SEARCH · Search NASA

Results for “directional element”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Influence of Shear Stiffness Degradation on Crack Paths in Uni-Directional Composite Laminates

Influence of shear stiffness degradation in an element, due to damage, on crack paths in uni-directional laminates has been demonstrated. A new shear stiffness degradation approach to improve crack path prediction has been developed and implemented in an ABAQUS/Explicit frame work using VUMAT. Three progressive failure analysis models, built-in ABAQUS (TradeMark), original COmplete STress Reduction (COSTR) and the modified COSTR damage models have been utilized in this study to simulate crack paths in five unidirectional notched laminates, 15deg, 30deg, 45deg, 60deg and 75deg under uniaxial tension load. Results such as crack paths and load vs. edge displacement curves are documented in this report. Modified COSTR damage model shows better accuracy in predicting crack paths in all the uni-directional laminates compared to the ABAQUS (TradeMark) and the original COSTR damage models.

Satyanarayana, Arunkumar↗
NASA NTRS1997

Heat Transfer Measurements on Surfaces with Natural Ice Castings and Modeled Roughness

An experimental method is described to measure and compare the convective heat transfer coefficient of natural and simulated ice accretion roughness and to provide a rational means for determining accretion-related enhanced heat transfer coefficients. The natural ice accretion roughness was a sample casting made from accretions at the NASA Lewis Icing Research Tunnel (IRT). One of these castings was modeled using a Spectral Estimation Technique (SET) to produce three roughness elements patterns that simulate the actual accretion. All four samples were tested in a flat-plate boundary layer at angle of attack in a "dry" wind tunnel test. The convective heat transfer coefficient was measured using infrared thermography. It is shown that, dispite some problems in the current data set, the method does show considerable promise in determining roughness-induced heat transfer coefficients, and that, in addition to the roughness height and spacing in the flow direction, the concentration and spacing of elements in the spanwise direction are important parameters.

Breuer, Kenneth S.↗
NASA NTRS1993

Moving-Temperature-Gradient Heat-Pipe Furnace Element

In improved apparatus, ampoule of material directionally solidified mounted in central hole of annular heat pipe, at suitable axial position between heated and cooled ends. Heated end held in fixed position in single-element furnace; other end left in ambient air or else actively cooled. Gradient of temperature made to move along heat pipe by changing pressure of noncondensable gas. In comparison with prior crystal-growing apparatuses, this one simpler, smaller, and more efficient.

Gillies, Donald C.↗
DOE OSTI2026

Feasibility Study on Implementing a Staggered-Grid Finite Volume Method for System Analysis Code Development Under the MOOSE Framework

Here, this work summarizes a feasibility study on testing numerical algorithms that are suitable and efficient for advanced system analysis code development under the mutli-physics framework, MOOSE. The key to the test bed is the implementation of high-order one-dimensional staggered-grid finite volume method (SG-FVM), and its direct interaction with the linear/nonlinear solver, PETSc. The test bed utilized a more flexible code structure to enable the finite volume method implementation and direct interacting with the solver package, instead of using the natively supported finite element method by the framework. Using a suite of selected test problems with different problem sizes and levels of complexity, the implemented SG-FVM demonstrated superior performance improvement against a direct finite element method implementation through MOOSE. On two computer systems, the speedup was observed to be significant, with at least one order of magnitude of solving time reduction. For a complex reactor model, transient simulation was performed using the newly developed finite volume method code, the results of which agree very well with the reference results from the finite element method code. Overall, this study demonstrates a successful feasibility study on the proposed numerical algorithms and software structure to support advanced system analysis tool development.

MOOSE↗
NASA NTRS1983

Wrinkling phenomenon in structures. II - Wrinkling criteria

The wrinkling phenomenon in elasticity is mathematically defined and described as a special type of instability associated with the loss of hyperbolicity of the governing equations when some of the characteristic speeds of elastic wave propagation become imaginary. The developed criteria of wrinkling are applied to such structural elements as membranes, strings, soft shells, soft rods, and laminated material. The cause of wrinkling in these elements is due to compression in longitudinal directions that exceeds the through-the-thickness shear modulus. For elements with internal fluid flow the critical compression is reduced due to the destabilizing effect of the flow. The most effective mathematical analysis technique is a combination of tensor analysis and index notations.

Zak, M.↗
NASA NTRSDate not supplied

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗
NASA NTRSDate not supplied

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗
NASA NTRS1989

Langley rotorcraft structural dynamics program: Background, status, accomplishments, plans

Excessive vibration is the most common technical problem to arise as a show stopper in the development of a new rotorcraft. Vibration predictions have not been relied on by the industry during design because of deficiencies in finite element dynamic analyses. A rotorcraft structural dynamics program aimed at meeting the industry's long-term needs in this key technical area was implemented at Langley in 1984. The subject program is a cooperative effort involving NASA, the Army, academia, and the helicopter industry in a series of generic research activities directed at establishing the critical elements of the technology base needed for development of a superior finite element dynamics design analysis capability in the U.S. helicopter industry. An executive overview of the background, status, accomplishments, and future direction of this program is presented.

Kvaternik, Raymond G.↗
NASA NTRSDate not supplied

Simulation of etch pit formation through active sites in carbon fiber micro-structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation as a result of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gasses such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗
NASA NTRS1989

The tapered slot antenna - A new integrated element for millimeter-wave applications

Tapered slot antennas (TSAs) with a number of potential applications as single elements and focal-plane arrays are discussed. TSAs are fabricated with photolithographic techniques and integrated in either hybrid or MMIC circuits with receiver or transmitter components. They offer considerably narrower beams than other integrated antenna elements and have high aperture efficiency and packing density as array elements. Both the circuit and radiation properties of TSAs are reviewed. Topics covered include: antenna beamwidth, directivity, and gain of single-element TSAs; their beam shape and the effect of different taper shapes; and the input impedance and the effects of using thick dielectrics. These characteristics are also given for TSA arrays, as are the circuit properties of the array elements. Different array structures and their applications are also described.

Yngvesson, K. Sigfrid↗
NASA NTRS1973

Electromagnetic wave energy converter

Electromagnetic wave energy is converted into electric power with an array of mutually insulated electromagnetic wave absorber elements each responsive to an electric field component of the wave as it impinges thereon. Each element includes a portion tapered in the direction of wave propagation to provide a relatively wideband response spectrum. Each element includes an output for deriving a voltage replica of the electric field variations intercepted by it. Adjacent elements are positioned relative to each other so that an electric field subsists between adjacent elements in response to the impinging wave. The electric field results in a voltage difference between adjacent elements that is fed to a rectifier to derive dc output power.

Bailey, R. L.↗
NASA NTRS1994

Static aeroelastic analysis of wings using Euler/Navier-Stokes equations coupled with improved wing-box finite element structures

Strong interactions between flow about an aircraft wing and the wing structure can result in aeroelastic phenomena which significantly impact aircraft performance. Time-accurate methods for solving the unsteady Navier-Stokes equations have matured to the point where reliable results can be obtained with reasonable computational costs for complex non-linear flows with shock waves, vortices and separations. The ability to combine such a flow solver with a general finite element structural model is key to an aeroelastic analysis in these flows. Earlier work involved time-accurate integration of modal structural models based on plate elements. A finite element model was developed to handle three-dimensional wing boxes, and incorporated into the flow solver without the need for modal analysis. Static condensation is performed on the structural model to reduce the structural degrees of freedom for the aeroelastic analysis. Direct incorporation of the finite element wing-box structural model with the flow solver requires finding adequate methods for transferring aerodynamic pressures to the structural grid and returning deflections to the aerodynamic grid. Several schemes were explored for handling the grid-to-grid transfer of information. The complex, built-up nature of the wing-box complicated this transfer. Aeroelastic calculations for a sample wing in transonic flow comparing various simple transfer schemes are presented and discussed.

Guruswamy, Guru P.↗
NASA NTRS2002

The Fractional Step Method Applied to Simulations of Natural Convective Flows

This paper describes research done to apply the Fractional Step Method to finite-element simulations of natural convective flows in pure liquids, permeable media, and in a directionally solidified metal alloy casting. The Fractional Step Method has been applied commonly to high Reynold's number flow simulations, but is less common for low Reynold's number flows, such as natural convection in liquids and in permeable media. The Fractional Step Method offers increased speed and reduced memory requirements by allowing non-coupled solution of the pressure and the velocity components. The Fractional Step Method has particular benefits for predicting flows in a directionally solidified alloy, since other methods presently employed are not very efficient. Previously, the most suitable method for predicting flows in a directionally solidified binary alloy was the penalty method. The penalty method requires direct matrix solvers, due to the penalty term. The Fractional Step Method allows iterative solution of the finite element stiffness matrices, thereby allowing more efficient solution of the matrices. The Fractional Step Method also lends itself to parallel processing, since the velocity component stiffness matrices can be built and solved independently of each other. The finite-element simulations of a directionally solidified casting are used to predict macrosegregation in directionally solidified castings. In particular, the finite-element simulations predict the existence of 'channels' within the processing mushy zone and subsequently 'freckles' within the fully processed solid, which are known to result from macrosegregation, or what is often referred to as thermo-solutal convection. These freckles cause material property non-uniformities in directionally solidified castings; therefore many of these castings are scrapped. The phenomenon of natural convection in an alloy under-going directional solidification, or thermo-solutal convection, will be explained. The development of the momentum and continuity equations for natural convection in a fluid, a permeable medium, and in a binary alloy undergoing directional solidification will be presented. Finally, results for natural convection in a pure liquid, natural convection in a medium with a constant permeability, and for directional solidification will be presented.

Westra, Douglas G.↗
NASA NTRS1973

Transient analysis using conical shell elements

The use of the NASTRAN conical shell element in static, eigenvalue, and direct transient analyses is demonstrated. The results of a NASTRAN static solution of an externally pressurized ring-stiffened cylinder agree well with a theoretical discontinuity analysis. Good agreement is also obtained between the NASTRAN direct transient response of a uniform cylinder to a dynamic end load and one-dimensional solutions obtained using a method of characteristics stress wave code and a standing wave solution. Finally, a NASTRAN eigenvalue analysis is performed on a hydroballistic model idealized with conical shell elements.

Yang, J. C. S.↗
DOE OSTI2025

Direct genome-scale screening of Gluconobacter oxydans B58 for rare earth element bioleaching

Abstract The transition to a sustainable energy economy will require an enormous increase in the supply of rare earth elements (REEs). Bioleaching offers a promising alternative to conventional hydrometallurgical methods for REE extraction from low-grade ores. However, exploiting this potential remains challenging due to large gaps in our understanding of the genetics involved, and inadequate biological tools to address them. We generated a highly non-redundant whole-genome knockout collection for the bioleaching microbe Gluconobacter oxydans B58, reducing redundancy by 85% compared to the previous best collection. This new collection was directly screened for bioleaching neodymium from a synthetic monazite powder, identifying 89 genes important for bioleaching, 68 of which have not previously been associated with this mechanism. We conducted bench-scale experiments to validate the extraction efficiency of promising strains: 8 demonstrated significant increases in extraction by up to 111% (δ GO_1598 , disruption of the gene encoding the orotate phosphoribosyltransferase enzyme PyrE), and one strain significantly reduced it by 97% (δ GO_1096 , disruption of the gene encoding the GTP-binding protein TypA). Notable changes in pH were only observed for 3 strains, suggesting an important role for non-acid mechanisms in bioleaching. These findings provide valuable insights into further enhancing REE-bioleaching by G. oxydans through genetic engineering.

Marecos, Sabrina (ORCID:0000000158529933)↗
NASA NTRS1991

Perceiving the coherent movements of spatially-separated features

When a partially-occluded object is represented in an image, it is defined by a set of spatially-separated features that may be registered at different spatial scales. To understand the image, human vision must organize these fragmented optical features into common and distinct object surfaces. Although the common fate of moving features often is considered a primary source of reliable information for image segmentation, little is known of the visual system's capacity to discriminate the coherent relative movements of spatially-separated features. In a series of experiments, observers viewed elements whose movements were correlated (direction and magnitude) or were uncorrelated. Our results indicate that observers can discriminate the two types of movement about as well as they can detect any movement at all. Moreover, the ability to perceive coherent movements is maintained under a variety of conditions including differences in the elements' spatial frequency content, spatial position and contrast, and temporal phase shifts between the spatially-correlated displacements. These results suggest that coherent relative motion may be a fundamental source of information exploited by vision, despite considerable variability in the spatial and temporal characteristics of the individual features.

Mowafy, Lyn↗