SEARCH · Search NASA

Results for “feedback based control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Decentralized control of large flexible structures by joint decoupling

A decentralized control design method is presented for large complex flexible structures by using the idea of joint decoupling. The derivation is based on a coupled substructure state-space model, which is obtained from enforcing conditions of interface compatibility and equilibrium to the substructure state-space models. It is shown that by restricting the control law to be localized state feedback and by setting the joint actuator input commands to decouple joint 'degrees of freedom' (dof) from interior dof, the global structure control design problem can be decomposed into several substructure control design problems. The substructure control gains and substructure observers are designed based on modified substructure state-space models. The controllers produced by the proposed method can operate successfully at the individual substructure level as well as at the global structure level. Therefore, not only control design but also control implementation is decentralized. Stability and performance requirement of the closed-loop system can be achieved by using any existing state feedback control design method. A two-component mass-spring damper system and a three-truss structure are used as examples to demonstrate the proposed method.

Su, Tzu-Jeng↗

NASA NTRS1997

Choosing Sensor Configuration for a Flexible Structure Using Full Control Synthesis

Optimal locations and types for feedback sensors which meet design constraints and control requirements are difficult to determine. This paper introduces an approach to choosing a sensor configuration based on Full Control synthesis. A globally optimal Full Control compensator is computed for each member of a set of sensor configurations which are feasible for the plant. The sensor configuration associated with the Full Control system achieving the best closed-loop performance is chosen for feedback measurements to an output feedback controller. A flexible structure is used as an example to demonstrate this procedure. Experimental results show sensor configurations chosen to optimize the Full Control performance are effective for output feedback controllers.

Lind, Rick↗

NASA NTRS1979

Filtering technique based on high-frequency plant modeling for high-gain control

This invention was an improvement in aircraft control systems that utilized feedback motion sensors to generate a signal to control the aircraft. The improvement consisted essentially of a complementary filter comprising a simplified model of the aircraft, a high pass filter, a low pass filter and a summing amplifier. The control signal was applied to the simplified model of the aircraft which attempted to compute the vehicle response to the signal. This computed response was then fed into the high pass filter to eliminate long term errors in the calculated response, with the result that a good estimate of the high frequency content of the aircraft motion was obtained. In order to obtain a good estimate of the low frequency content of the motion, a rate gyro signal was fed through the low pass filter that eliminates all of the offending noise.

Niessen, F. R.↗

DOE OSTI2024

Feedback-based quantum algorithms for ground state preparation

The ground state properties of quantum many-body systems are a subject of interest across chemistry, materials science, and physics. Thus, algorithms for finding ground states can have broad impacts. Variational quantum algorithms are one class of ground state algorithms that has received significant attention in recent years. These algorithms utilize a hybrid quantum-classical computing framework to prepare ground states on quantum computers. However, this requires solving a classical optimization problem that can become prohibitively expensive in high dimensions. Here, we develop formulations of feedback-based quantum algorithms for ground state preparation that can be used to address this challenge for two broad classes of Hamiltonians: Fermi-Hubbard Hamiltonians, and molecular Hamiltonians represented in second quantization. Feedback-based quantum algorithms are optimization-free; in place of classical optimization, quantum circuit parameters are set according to a deterministic feedback law derived from quantum Lyapunov control principles. This feedback law guarantees a monotonic improvement in solution quality with respect to the depth of the quantum circuit. A variety of numerical illustrations are provided that analyze the convergence and robustness of feedback-based quantum algorithms for these problem classes. Published by the American Physical Society 2024

Larsen, James B. (ORCID:000000020777440X)↗

DOE OSTI2024

Instant Startup and Grid Synchronization of Inverter Based Resources

This paper introduces an innovative approach for instant startup of inverter-based resources (IBRs), which attains synchronization with the grid via the already embedded direct current feedback control. The startup process utilizes direct current control throughout each switching cycle, enabling a process that is free from inrush current. Uniquely, this method determines the grid phase angle by evaluating the current differences across switching cycles, a significant difference from traditional methods that often rely on grid or points of common coupling (PCC) voltage. An analytical model has been constructed, highlighting that the grid phase angle can be obtained in just two switching cycles. The paper details the principle of instant grid synchronization and presents both simulation and experimental results to substantiate the proposed method.

He, Yuchen↗

NASA NTRS1973

Evaluation of glide paths for landing a VTOL airplane using linear regulator theory.

A method of evaluating certain characteristics of approach paths for VTOL airplanes is presented which is based on the solution of the matrix Riccati equation to obtain an optimal state variable feedback controller. The longitudinal equations of motion of the airplane are linearized about a preselected path and the resulting system of equations is treated as a linear, time-varying regulator. The controller which minimizes a quadratic cost function is applied to the linearized system to determine the airplane's ability to return to the prescribed path given a specified initial error in altitude. The procedure is applied to the XC-142A, tilt-wing, V/STOL airplane, under decelerating approach conditions with a glide path consisting of two segments, the first having a smaller angle of descent than the second.

Reid, G. F.↗

NASA NTRS1976

Locally stabilizable large-scale systems

A class of large scale linear systems, stabilizable by local feedback control applied around each decoupled subsystem, is established. The control scheme, outlined in the paper, is based upon the decomposition-aggregation method, and involves only operations on the subsystem level. The systems, stabilized by the proposed method, have a tolerance to a wide class of non-linearities, and are reliable with respect to the structural perturbations.

Vukcevic, M. B.↗

NASA NTRS1983

Orbiting chains and rings

Two very different, highly flexible, space structures proposed during the last decade which involve analytical solution of certain partial differential equations are discussed. The first structure is an array, or hanging chain of aluminum beads which would serve as a convenient communicator if, under the influence of the Earth's gravity gradient, it assumes a local vertical orientation as it circles the Earth. Two passive schemes have been proposed for damping the rigid modes: twist the wire at the ends to provide non-zero moment of inertia about the vertical, thereby inducing relative motion of the two tips during rigid pitch or roll, and thus exercising a damper; and introduce weak lossy springs between the end sections and the main section; thereby providing linear coupling between the springs and all the in-plane (pitch) modes. The second structure is a complete ring of satellites cabled together at synchronous altitude. By a slight increase in altitude, the cable is in tension. This configuration is, however, unstable, and an active feedback control scheme is required to stabilize it. A possible scheme involves local cable length adjustment based on measurement of local altitude and shape variations and their rates.

Breakwell, J. V.↗

NASA NTRS1985

An automatic redesign approach for restructurable control systems

This paper presents an approach to the automatic redesign of flight control systems for aircraft that have suffered one or more control element failures. The procedure is based on Linear Quadratic design techniques, and produces a control system that maximizes a measure of feedback system performance subject to a bandwidth constraint.

Looze, D. P.↗

NASA NTRS1991

The NASA Lewis integrated propulsion and flight control simulator

A new flight simulation facility was developed at NASA-Lewis. The purpose of this flight simulator is to allow integrated propulsion control and flight control algorithm development and evaluation in real time. As a preliminary check of the simulator facility capabilities and correct integration of its components, the control design and physics models for a short take-off and vertical landing fighter aircraft model were shown, with their associated system integration and architecture, pilot vehicle interfaces, and display symbology. The initial testing and evaluation results show that this fixed based flight simulator can provide real time feedback and display of both airframe and propulsion variables for validation of integrated flight and propulsion control systems. Additionally, through the use of this flight simulator, various control design methodologies and cockpit mechanizations can be tested and evaluated in a real time environment.

Bright, Michelle M.↗

NASA NTRS1983

Partial and robust linearization by feedback

It is argued that if the nonlinearities in a system are mild, and the controller is sufficiently stabilizing, the inaccuracies of a linear model, which is often taken to be sufficient for a controller design, can be safely neglected. For systems with severe nonlinearity a linearizing technique is described, based on the change of state coordinates and nonlinear feedback; in the total context of a stable feedback design the linearization technique is considered robust. Furthermore, attention is paid to partial linearization using the same transformations. It is found that there always exist maximally linearizing transformations which are not necessarily unique.

Krener, A. J.↗

NASA NTRS1991

The NASA Lewis integrated propulsion and flight control simulator

A new flight simulation facility has been developed at NASA Lewis to allow integrated propulsion-control and flight-control algorithm development and evaluation in real time. As a preliminary check of the simulator facility and the correct integration of its components, the control design and physics models for an STOVL fighter aircraft model have been demonstrated, with their associated system integration and architecture, pilot vehicle interfaces, and display symbology. The results show that this fixed-based flight simulator can provide real-time feedback and display of both airframe and propulsion variables for validation of integrated systems and testing of control design methodologies and cockpit mechanizations.

Bright, Michelle M.↗

NASA NTRS1981

Design and evaluation of a state-feedback vibration controller

The effectiveness and practicality of the state-feedback vibration controller is demonstrated by computer simulations. It is shown that: (1) the required measurements can be reduced to fuselage accelerations; (2) the system is stable over a wide range of flight conditions; (3) a discrete design for the controller provides effective digital implementation at 80-Hz sampling; (4) attenuation produced by the actuators does not create a problem, and a simple lead compensator provides vibration reduction; and (5) a design based on a hover model worked well at five knots. At 40 and 120 knots, vibrations in all but the vertical acceleration were effectively suppressed. The state-feedback vibration controller has a rapid convergence time and implementation is easier than with multicyclic control since no on-line harmonic analysis or identification algorithms are required.

Du Val, R. W.↗

NASA NTRS2006

A High-Authority/Low-Authority Control Strategy for Coupled Aircraft-Style Bays

This paper presents a numerical investigation of an active structural acoustic control strategy for coupled aircraft-style bays. While structural coupling can destabilize or limit the performance of some model-based decentralized control systems, fullycoupled centralized control strategies are impractical for typical aircraft containing several hundred bays. An alternative is to use classical rate feedback with matched, collocated transducer pairs to achieve active damping. Unfortunately, due to the conservative nature of this strategy, stability is guaranteed at the expense of achievable noise reduction. Therefore, this paper describes the development of a combined control strategy using robust active damping in addition to a high-authority controller based on linear quadratic Gaussian (LQG) theory. The combined control system is evaluated on a tensioned, two-bay model using piezoceramic actuators and ideal point velocity sensors. Transducer placement on the two-bay structure is discussed, and the advantages of a combined control strategy are presented.

Schiller, N. H.↗

NASA NTRS1988

A parallel row-based algorithm with error control for standard-cell replacement on a hypercube multiprocessor

A new row-based parallel algorithm for standard-cell placement targeted for execution on a hypercube multiprocessor is presented. Key features of this implementation include a dynamic simulated-annealing schedule, row-partitioning of the VLSI chip image, and two novel new approaches to controlling error in parallel cell-placement algorithms; Heuristic Cell-Coloring and Adaptive (Parallel Move) Sequence Control. Heuristic Cell-Coloring identifies sets of noninteracting cells that can be moved repeatedly, and in parallel, with no buildup of error in the placement cost. Adaptive Sequence Control allows multiple parallel cell moves to take place between global cell-position updates. This feedback mechanism is based on an error bound derived analytically from the traditional annealing move-acceptance profile. Placement results are presented for real industry circuits and the performance is summarized of an implementation on the Intel iPSC/2 Hypercube. The runtime of this algorithm is 5 to 16 times faster than a previous program developed for the Hypercube, while producing equivalent quality placement. An integrated place and route program for the Intel iPSC/2 Hypercube is currently being developed.

Sargent, Jeff Scott↗

NASA NTRS2018

Feedback Control of Flight Speed to Reduce Unmanned Aerial System Noise

The aim of this initial study is to incorporate an acoustic metric into the flight control system of an unmanned aerial vehicle. This could be used to mitigate the noise impact of unmanned aerial systems operating near residential communities. To incorporate an acoustic metric into a pre-existing flight control system, two things are required: a source noise model, and an acoustic controller. An acoustic model was developed based on Gutin's work to estimate propeller noise. The flight control system was augmented with a controller to reduce propeller noise using feedback control of the commanded flight speed until an acoustic target was met. This control approach focuses on modifying flight speed only, with no perturbation to the trajectory. Multiple flight simulations were performed and the results showed that integrating an acoustic metric into the flight control system of an unmanned aerial system is possible.

Matthew B Galles↗

NASA NTRS2013

Advanced Shock Position Control for Mode Transition in a Turbine Based Combined Cycle Engine Inlet Model

A dual flow-path inlet system is being tested to evaluate methodologies for a Turbine Based Combined Cycle (TBCC) propulsion system to perform a controlled inlet mode transition. Prior to experimental testing, simulation models are used to test, debug, and validate potential control algorithms. One simulation package being used for testing is the High Mach Transient Engine Cycle Code simulation, known as HiTECC. This paper discusses the closed loop control system, which utilizes a shock location sensor to improve inlet performance and operability. Even though the shock location feedback has a coarse resolution, the feedback allows for a reduction in steady state error and, in some cases, better performance than with previous proposed pressure ratio based methods. This paper demonstrates the design and benefit with the implementation of a proportional-integral controller, an H-Infinity based controller, and a disturbance observer based controller.

Csank, Jeffrey T.↗

NASA NTRS1988

Active spacecraft potential control: An ion emitter experiment

The cluster spacecraft are instrumented with ion emitters for charge neutralization. The emitters produce indium ions at 6 keV. The ion current is adjusted in a feedback loop with instruments measuring the spacecraft potential. The system is based on the evaporation of indium in the apex field of a needle. The design of the active spacecraft potential control instruments, and the ion emitters is presented.

Riedler, W.↗