Search NASA⌕ Search

SEARCH · Search NASA

Results for “high loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Toward Understanding Tip Leakage Flows in Small Compressor Cores Including Stator Leakage Flow

The focus of this work was to provide additional data to supplement the work reported in NASA/CR-2015-218868 (Berdanier and Key, 2015b). The aim of that project was to characterize the fundamental flow physics and the overall performance effects due to increased rotor tip clearance heights in axial compressors. Data have been collected in the three-stage axial research compressor at Purdue University with a specific focus on analyzing the multistage effects resulting from the tip leakage flow. Three separate rotor tip clearances were studied with nominal tip clearance gaps of 1.5 percent, 3.0 percent, and 4.0 percent based on a constant annulus height. Overall compressor performance was previously investigated at four corrected speedlines (100 percent, 90 percent, 80 percent, and 68 percent) for each of the three tip clearance configurations. This study extends the previously published results to include detailed steady and time-resolved pressure data at two loading conditions, nominal loading (NL) and high loading (HL), on the 100 percent corrected speedline for the intermediate clearance level (3.0 percent). Steady detailed radial traverses of total pressure at the exit of each stator row are supported by flow visualization techniques to identify regions of flow recirculation and separation. Furthermore, detailed radial traverses of time-resolved total pressures at the exit of each rotor row have been measured with a fast-response pressure probe. These data were combined with existing three-component velocity measurements to identify a novel technique for calculating blockage in a multistage compressor. Time-resolved static pressure measurements have been collected over the rotor tips for all rotors with each of the three tip clearance configurations for up to five loading conditions along the 100 percent corrected speedline using fast-response piezoresistive pressure sensors. These time-resolved static pressure measurements reveal new knowledge about the trajectory of the tip leakage flow through the rotor passage. Further, these data extend previous measurements identifying a modulation of the tip leakage flow due to upstream stator wake propagation. Finally, a novel instrumentation technique has been implemented to measure pressures in the shrouded stator cavities. These data provide boundary conditions relating to the flow across the shrouded stator knife seal teeth. Moreover, the utilization of fast-response pressure sensors provides a new look at the time-resolved pressure field, leading to instantaneous differential pressures across the seal teeth. Ultimately, the data collected for this project represent a unique data set which contributes to build a better understanding of the tip leakage flow field and its associated loss mechanisms. These data will facilitate future engine design goals leading to small blade heights in the rear stages of high pressure compressors and aid in the development of new blade designs which are desensitized to the performance penalties attributed to rotor tip leakage flows.

Berdanier, Reid A.↗

General synthesis of single-atom catalysts with high metal loading using graphene quantum dots

Transition-metal single-atom catalysts present extraordinary activity per metal atomic site, but suffer from low metal-atom densities (typically less than 5 wt% or 1 at.%), which limits their overall catalytic performance. Here we report a general method for the synthesis of single-atom catalysts with high transition-metal-atom loadings of up to 40 wt% or 3.8 at.%, representing several-fold improvements compared to benchmarks in the literature. Graphene quantum dots, later interweaved into a carbon matrix, were used as a support, providing numerous anchoring sites and thus facilitating the generation of high densities of transition-metal atoms with sufficient spacing between the metal atoms to avoid aggregation. A significant increase in activity in electrochemical CO 2 reduction (used as a representative reaction) was demonstrated on a Ni single-atom catalyst with increased Ni loading.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nonlinear static TPS analysis

A nonlinear analysis which includes the effect of mismatch and filler bar was developed to predict the strain isolator pad reuseable surface insulation through-the-thickness interface stresses. Parametric studies were conducted for simulated shock loading on square tiles. Expected loads on an actual tile were also studied. The results indicate that when no mismatch is present, linear solutions tend to give nonconservative maximum stresses relative to the nonlinear solutions. When mismatch is present, the linear maximum stresses are only conservative at low load levels and highly nonconservative at high load levels. Although the presence of filler bar reduces maximum tensile stresses in some cases, it does not appear that the nominal dimension filler bar can reduce the nonlinear stress to a level at which the linear solution becomes conservative relative to the nonlinear solution. Moreover, on an outboard trailing edge elevon tile at descent with +20 deg flap, the linear analysis is 49% nonconservative relative to the nonlinear analysis with filler bar.

Housner, J. M.↗

Spin tests of a single-engine, high-wing light airplane

The airplane has a relatively steep spin mode (low angle of attack) with a high load factor and high velocity. The airplane recovers almost immediately after any deviation from the prospin control positions, except for one maneuver with reduced flexibility in the elevator control system.

Stewart, E. C.↗

Life considerations of the shuttle orbiter densified-tile thermal protection system

The Shuttle orbiter themal protection system (TPS) incorporates ceramic reusable surface insulation tiles bonded to the orbiter substructure through a strain isolation pad. Densification of the bonding surface of the tiles increases the static strength of the tiles. The densification proces does not, however, necessarily lead to an equivalent increase in fatigue strength. Investigation of the expected lifetime of densified tile TPS under both sinusoidal loading and random loading simulating flight conditions indicates that the strain isolation pads are the weakest components of the TPS under fatigue loading. The felt pads loosen under repetitive loading and, in highly loaded regions, could possibly cause excessive step heights between tiles causing burning of the protective insulation between tiles. A method of improving the operational lifetime of the TPS by using a strain isolation pad with increased stiffness is presented as is the consequence of the effect of increased stiffness on the tile inplane strains and transverse stresses.

Cooper, P. A.↗

Dynamic Torque Calibration Unit

Proposed dynamic torque calibration unit (DTCU) measures torque in rotary actuator components such as motors, bearings, gear trains, and flex couplings. Unique because designed specifically for testing components under low rates. Measures torque in device under test during controlled steady rotation or oscillation. Rotor oriented vertically, supported by upper angular-contact bearing and lower radial-contact bearing that floats axially to prevent thermal expansion from loading bearings. High-load capacity air bearing available to replace ball bearings when higher load capacity or reduction in rate noise required.

Agronin, Michael L.↗

Nanomaterial-Treated Filters for the Uptake of Heavy Metals from Water Sources

We describe the synthesis and properties of ligand-modified gold nanoparticles (AuNPs) grown on stainless steel wool filters. Their selectivity and efficiency with regards to heavy metal uptake from groundwater and other sources of drinking water found at or near DOE facilities were also investigated. The nanomaterial-treated filters are advantageous because they serve as inactive supports that allow for efficient flow of the contaminated water, and can be easily replaced after heavy metal uptake. They are also comparable to nanomaterials free in solution with regards to the effectiveness of remediation of drinking water. Environmental stewardship is at the forefront of core competencies at SRNS. This includes treatment and remediation of contaminated groundwater. Among contaminants present in water resources, hazardous heavy metals and radioactive contaminants are the main concerns in the DOE complex. With the advent of nanotechnology, new remediation technologies have emerged. AuNPs have unique optical properties and enormous surface areas, making them good candidates for water remediation. They can be functionalized with ligands, e.g. citrate and L-cysteine, allowing them to serve as an excellent platform for environmental stewardship applications. Objectives: 1. Nanomaterial development and characterization Ligand-modified AuNPs: (a) in solution and (b) on stainless steel wool filters 2. Nanomaterial evaluation for efficiency and selectivity of heavy metal uptake, including Cu{sup 2+} and Zn{sup 2+}. Materials and Methods: Chloroauric acid (HAuCl{sub 4}), sodium citrate (reducing and capping agent); Stainless steel wool (SSW) was used as a support and filter; L-cysteine- ligand for surface functionalization; Zinc acetate and copper nitrate: heavy metal ions contaminants. Au NPs were prepared by wet chemistry methods. They were characterized by UV-Vis, Zeta sizer and potential, SEM, EDS and EDS mapping to understand their physico-chemical properties. Results and Discussions: Surface modification of AuNPs with surfactants changes their optical properties. Citrate capped AuNPs demonstrate high loading capacity for both heavy metals. L-cysteine capped AuNPs demonstrate high loading capacity for Zn{sup 2+}. Citrate capped AuNPs have excellent sensitivity towards heavy metal ions (0.05 mM can be detected). L-cysteine capped AuNPs can detect heavy metal ions at low concentrations, making them useful for sensing. Conclusions: AuNPs in solution and on SSW were successfully synthesized and characterized. Two functional sensing and remediation technologies - colorimetric sensor and AuNP-treated filters - were developed through wet chemistry methods. AuNP SSW filters exhibit different characteristics (size, shape, etc.) than AuNPs in solution and are efficient at the uptake of heavy metal ions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Envera Variable Compression Ratio Engine

Aggressive engine downsizing, variable compression ratio and use of the Atkinson cycle are being combined to improve fuel economy by up to 40 percent relative to port fuel injected gasoline engines, while maintaining full engine power. Approach Engine downsizing is viewed by US and foreign automobile manufacturers as one of the best options for improving fuel economy. While this strategy has already demonstrated a degree of success, downsizing and fuel economy gains are currently limited. With new variable compression ratio technology however, the degree of engine downsizing and fuel economy improvement can be greatly increased. A small variable compression ratio (VCR) engine has the potential to return significantly higher vehicle fuel economy while also providing high power. Affordability and potential for near term commercialization are key attributes of the Envera VCR engine. VCR Technology To meet torque and power requirements, a smaller engine needs to do more work per stroke. This is typically accomplished by boosting the incoming charge with either a turbo or supercharger so that more energy is present in the cylinder per stroke to do the work. With current production engines the degree of engine boosting (which correlates to downsizing) is limited by detonation (combustion knock) at high boost levels. Additionally, the turbo or supercharger needs to be responsive and efficient while providing the needed boost. VCR technology eliminates the limitation of engine knock at high load levels by reducing compression ratio to {approx}9:1 (or whatever level is appropriate) when high boost pressures are needed. By reducing the compression ratio during high load demand periods there is increased volume in the cylinder at top dead center (TDC) which allows more charge (or energy) to be present in the cylinder without increasing the peak pressure. Cylinder pressure is thus kept below the level at which the engine would begin to knock. When loads on the engine are low the compression ratio can be raised (to as much as 18:1) providing high engine efficiency. It is important to recognize that for a well designed VCR engine cylinder pressure does not need to be higher than found in current production turbocharged engines. As such, there is no need for a stronger crankcase, bearings and other load bearing parts within the VCR engine. The Envera VCR mechanism uses an eccentric carrier approach to adjust engine compression ratio. The crankshaft main bearings are mounted in this eccentric carrier or 'crankshaft cradle' and pivoting the eccentric carrier 30 degrees adjusts compression ratio from 9:1 to 18:1. The eccentric carrier is made up of a casting that provides rigid support for the main bearings, and removable upper bearing caps. Oil feed to the main bearings transits through the bearing cap fastener sockets. The eccentric carrier design was chosen for its low cost and rigid support of the main bearings. A control shaft and connecting links are used to pivot the eccentric carrier. The control shaft mechanism features compression ratio lock-up at minimum and maximum compression ratio settings. The control shaft method of pivoting the eccentric carrier was selected due to its lock-up capability. The control shaft can be rotated by a hydraulic actuator or an electric motor. The engine shown in Figures 3 and 4 has a hydraulic actuator that was developed under the current program. In-line 4-cylinder engines are significantly less expensive than V engines because an entire cylinder head can be eliminated. The cost savings from eliminating cylinders and an entire cylinder head will notably offset the added cost of the VCR and supercharging. Replacing V6 and V8 engines with in-line VCR 4-cylinder engines will provide high fuel economy at low cost. Numerous enabling technologies exist which have the potential to increase engine efficiency. The greatest efficiency gains are realized when the right combination of advanced and new technologies are packaged together to provide the greatest gains at the least cost. Aggressive engine downsizing with variable compression ratio and use of the extended Atkinson cycle can provide large fuel economy gains that are exceptionally cost effective. Analysis indicates that a 2.2L supercharged Envera VCR engine can match the torque of a larger V8 engine at 2000 rpm. The VCR engine's high torque value at low engine speed is beneficial for maintaining the driving feel and responsiveness of the larger V8 engine. The Envera VCR engine will attain high efficiency at {approx}100 Nm primarily due to the combination of engine down-sizing and use of the Atkinson cycle. Qualitatively the fuel economy gain realized from down-sizing from a V8 to an Atkinson-cycle I-4 is about twice as large as the benefits from down-sizing from a V8 to a Turbo V6 when evaluated at 100 Nm 2000 rpm.

33 ADVANCED PROPULSION SYSTEMS↗

Mask Projection Stereolithography for Manufacturing Ceramic Parts for CO 2 Capture and Sequestration

With increased CO 2 in the atmosphere and climate change becoming central in today’s political climate, it is important to make attempts to alleviate climate change. CO 2 capture is possible at the source of some of the larges CO 2 producers – industrial firms – where it can be collected via separation membranes. While current state-of-the-art technology is amine gas treatment or polymer membranes, ceramic membranes infilled with hydroxide offer a more energetically efficient solution. Stereolithography offers a unique manufacturing technique to create uniquely-shaped ceramic parts that will maximize carbon capture while maintaining low energy needs and low cost. High-loading ceramic slurries can be more difficult to manufacture using stereolithography due to high viscosity and opacity, but produce stronger pieces when sintered. The current challenge is optimizing high-load ceramic slurries for stereolithography to print pieces with large surface areas and parts on the micrometer-scale.

36 MATERIALS SCIENCE↗

Aerodynamic Loss Generation in a Low-Pressure Turbine Stage with High Lift Blading

Background - A joint program (FAA): Honeywell-U.S. Air Force- NASA to develop highly-loaded LPT stages Objective of current work - Application and evaluation of a High-Fidelity numerical simulation for flow field in a highly loaded LPT stage. 1. loss generation mechanism. 2. Reynolds number effects on stage performance

low pressure turbine↗

Atomically Dispersed Pentacoordinated‐Zirconium Catalyst with Axial Oxygen Ligand for Oxygen Reduction Reaction

Single-atom catalysts (SACs), as promising alternatives to Pt-based catalysts, suffer from the limited choice of center metals and low single-atom loading. Here, we report a pentacoordinated Zr-based SAC with nontrivial axial O ligands (denoted O-Zr-N-C) for oxygen reduction reaction (ORR). The O ligand downshifts the d-band center of Zr and confers Zr sites with stable local structure and proper adsorption capability for intermediates. Consequently, the ORR performance of O-Zr-N-C prominently surpasses that of commercial Pt/C, achieving a half-wave potential of 0.91 V vs. reversible hydrogen electrode and outstanding durability (92% current retention after 130-hour operation). Moreover, the Zr site shows good resistance towards aggregation, enabling the synthesis of Zr-based SAC with high loading (9.1 wt%). With the high-loading catalyst, the zinc-air battery (ZAB) delivers a record-high power density of 324 mW cm -2 among those of SAC-based ZABs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Switching Modes for Reduction of Peak Voltage Transients in GaN-Based Three Level ANPC Inverter

The switching pole voltage can transition between P,0, and N states in a three-level active neutral point clamped (ANPC) inverter. State transitions between 0-P and 0-N can be realized with different switching modes. Three switching modes- Short 1 , Short 2 , and Full are studied considering the effect of capacitive current paths. The role of clamping and inner switch on/off conditions is determined using simplified equivalent circuit models. Short 2 with clamping switch off is beneficial for turn-on overvoltage suppression but results in high turn-off overvoltage. Full mode with a parallel current sharing path is effective for turn-off overvoltage suppression but leads to high turn-on overvoltage. Hence, a Modified Full mode is proposed to achieve the simultaneous objective of overvoltage suppression at both turn-on and turn-off transient during high load currents. This benefits 3L ANPC operation at a low power factor with a high load current at fundamental voltage zero crossing points. Here, a 650V GaN-based three-level ANPC inverter prototype is designed and used to evaluate the switching modes and overvoltage suppression strategies through double pulse tests and continuous operation.

42 ENGINEERING↗

Gel based sulfur cathodes with a high sulfur content and large mass loading for high-performance lithium–sulfur batteries

A significantly improved conductive matrix design for the sulfur electrode is essential to solve several problems related to sulfur electrochemistry toward the development of practical lithium–sulfur batteries (LSBs). Great progress has been made by using a variety of carbon-based nanostructures for physically and chemically confining soluble polysulfides as well as providing conductive paths. However, most of these electrode designs have a low sulfur content or a low sulfur loading, leading to a low specific capacity or low areal capacity at the electrode level. Herein, intrinsically N- and O-doped carbon nanoribbon (CNR) aerogels, obtained by pyrolysis of bacterial cellulose (BC) aerogels, were employed to form gel-based sulfur cathodes, simultaneously achieving both a high sulfur content and a high sulfur loading. With a sulfur loading of 6.4 mg cm−2 and a sulfur content of 90% at the whole electrode (including the current collector) level, a capacity as high as 943 mA h g−1 was achieved, which corresponds to an areal capacity of 5.9 mA h cm−2. The outstanding cell performance is attributed to the gel based cathode structure, which can strongly hold a large amount of the catholyte and relieve the shuttle effect of lithium polysulfides.

Li, Shiqi↗

Fuel Property Effects on Stochastic Preignition Events During Engine Load Transitions

Stochastic preignition (SPI) is an abnormal combustion phenomenon that can cause catastrophic engine damage. There have been several proposed mechanisms of SPI, where a uniform source is still not certain, however, SPI tendencies have been shown to be influenced by engine operating conditions, oil composition, engine age, and fuel chemical and physical properties. Laboratory research and testing for SPI propensity is challenging given the stochastic nature of events, as well as the potential for significant degradation of the engine platform and measuring equipment over time. Thus, SPI specific experiments are generally conducted under either sustained or cyclic patterning of steady-state operating conditions to avoid the influence of transient engine boundary conditions on test parameters of interest (e.g. oil additive package, fuel properties, engine speed/load, etc.). In this work a cyclically varying SPI test sequence involves a 5 min engine warmup period at a low engine load of around 4 bar gross indicated mean effective pressure (IMEPg), followed by a transition to high load (~20 bar IMEPg) at a constant 2000 rev/min engine speed for a total of 25 min. This individual test sequence load schedule is then sequentially repeated 10 times to generate significant statistical data for analysis. This work examines the influence of fuel chemical and physical properties on SPI tendency during the unsteady portion of the 10-cycle sequence (the first 5 min of the high load operation in each sequence of the loading cycle) which has been discarded from previous analyses due to the uncertainty in engine operating and thermal boundary conditions. Results from this analysis suggest an increasing trend in the ratio of SPI events during the unsteady test period relative to the steady test period with increasing fuel Reid Vapor Pressure (RVP), implying differences in uncontrolled ignition source terms, possibly from, fuel wall interactions and retention during the load transition phase of the test.

Splitter, Derek [ORNL] (ORCID:0000000174044047)↗

Wireless power charging using point of load controlled high frequency power converters

An apparatus for wirelessly charging a battery of an electric vehicle is provided with a point of load control. The apparatus includes a base unit for generating a direct current (DC) voltage. The base unit is regulated by a power level controller. One or more point of load converters can be connected to the base unit by a conductor, with each point of load converter comprising a control signal generator that transmits a signal to the power level controller. The output power level of the DC voltage provided by the base unit is controlled by power level controller such that the power level is sufficient to power all active load converters when commanded to do so by any of the active controllers, without generating excessive power that may be otherwise wasted.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Effects of Radiation and a High Iron Load on Bone Mineral Density

Astronauts on long duration space flight missions to the moon or mars are exposed to radiation and have increase iron (Fe) stores, both of which can independently induce oxidative stress and may exacerbate bone mass loss and strength. We hypothesize a high Fe diet and a fractionated gamma radiation exposure would increase oxidative stress and lower bone mass. Three mo-old, SD rats (n=32) were randomized to receive an adequate Fe diet (45 mg Fe/kg diet) or a high Fe diet (650 mg Fe/kg diet) for 4 wks and either a cumulative 3 Gy dose (fractionated 8 x 0.375 Gy) of gamma radiation (Cs-137) or sham exposure starting on day 14. Elisa kit assessed serum catalase, clinical analyzer assessed serum Fe status and ex vivo pQCT scans measured bone parameters in the proximal/midshaft tibia and femoral neck. Mechanical strength was assessed by 3-pt bending and femoral neck test. There is a significant decrease in trabecular bone mineral density (BMD) from radiation (p less than 0.05) and a trend in diet (p=0.05) at the proximal tibia. There is a significant interaction in cortical BMD from the combined treatments at the midshaft tibia (p less than 0.05). There is a trending decrease in total BMD from diet (p=0.07) at the femoral neck. In addition, high serum Fe was correlated to low trabecular BMD (p less than 0.05) and high serum catalase was correlated to low BMD at all 3 bone sites (p less than 0.05). There was no difference in the max load of the tibia or femoral neck. Radiation and a high iron diet increases iron status and catalase in the serum and decreases BMD.

Yuen, E.↗

Charge transport model in nanodielectric composites based on quantum tunneling mechanism and dual-level traps

Charge transport properties in nanodielectrics present different tendencies for different loading concentrations. The exact mechanisms that are responsible for charge transport in nanodielectrics are not detailed, especially for high loading concentration. A charge transport model in nanodielectrics has been proposed based on quantum tunneling mechanism and dual-level traps. In the model, the thermally assisted hopping (TAH) process for the shallow traps and the tunnelling process for the deep traps are considered. For different loading concentrations, the dominant charge transport mechanisms are different. The quantum tunneling mechanism plays a major role in determining the charge conduction in nanodielectrics with high loading concentrations. While for low loading concentrations, the thermal hopping mechanism will dominate the charge conduction process. The model can explain the observed conductivity property in nanodielectrics with different loading concentrations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-performance silicon anodes enabled by nonflammable localized high-concentration electrolytes

Silicon (Si) anode is regarded as one of the most promising alternatives to graphite for high energy density lithium ion batteries (LIBs), but their practical applications have been hindered by high volume change, limited cycle life and safety concerns. In this work we developed nonflammable localized high concentration electrolytes (LHCEs) for Si-based anodes. The LHCEs enabled the Si anodes with significantly enhanced electrochemical performances comparing to the conventional carbonate electrolytes with high content of fluoroethylene carbonate (FEC). The LHCE with only 1.2 wt% FEC can further improve the long-term cycling stability of Si-based anodes. When coupled with a LiNi0.3Mn0.3Co0.3O2 cathode, the full cells using this nonflammable LHCE could maintain >90% capacity after 600 cycles at C/2 rate, demonstrate excellent rate capability and cycling stability at elevated temperatures and high loadings. This work casts new insights in electrolyte development from the perspective of in-situ Si/electrolyte interphase protection for high energy density LIBs with Si anodes.

Silicon anode, electrolyte, nonflammable, localize↗