Search NASA⌕ Search

SEARCH · Search NASA

Results for “high performance and distributed computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

High performance architecture for robot control

Practical aspects of the design and implementation of a modular, high performance, parallel computer control system for telerobots are discussed. Topics of consideration include system architecture, operator interface, and control execution. In a laboratory environment, a telerobotics test control configuration is used to obtain measurements on communications and control loop timing for use in an effective full scale operational system design. The feasibility of the selected architectural approach has been successfully demonstrated. The modularity of the software and hardware enables ease of transport for use in the operational system. The distributed partioning of the control algorithms and the performance measurements acquired during control system implementation are discussed.

Byler, E.↗

Heat Transfer and Flow on the First Stage Blade Tip of a Power Generation Gas Turbine: Experimental Results - Part 1

A combined computational and experimental study has been performed to investigate the detailed distribution of convective heat transfer coefficients on the first stage blade tip surface for a geometry typical of large power generation turbines(>100MW). This paper is concerned with the design and execution of the experimental portion of the study. A stationary blade cascade experiment has been run consisting of three airfoils, the center airfoil having a variable tip gap clearance. The airfoil models the aerodynamic tip section of a high pressure turbine blade with inlet Mach number of 0.30, exit Mach number of 0.75, pressure ratio of 1.45, exit Reynolds number based on axial chord of 2.57 x 10(exp 6), and total turning of about 110 degrees. A hue detection based liquid crystal method is used to obtain the detailed heat transfer coefficient distribution on the blade tip surface for flat, smooth tip surfaces with both sharp and rounded edges. The cascade inlet turbulence intensity level took on values of either 5% or 9%. The cascade also models the casing recess in the shroud surface ahead of the blade. Experimental results are shown for the pressure distribution measurements on the airfoil near the tip gap, on the blade tip surface, and on the opposite shroud surface. Tip surface heat transfer coefficient distributions are shown for sharp-edge and rounded-edge tip geometries at each of the inlet turbulence intensity levels.

Bunker, Ronald S.↗

Machine characterization based on an abstract high-level language machine

Measurements are presented for a large number of machines ranging from small workstations to supercomputers. The authors combine these measurements into groups of parameters which relate to specific aspects of the machine implementation, and use these groups to provide overall machine characterizations. The authors also define the concept of pershapes, which represent the level of performance of a machine for different types of computation. A metric based on pershapes is introduced that provides a quantitative way of measuring how similar two machines are in terms of their performance distributions. The metric is related to the extent to which pairs of machines have varying relative performance levels depending on which benchmark is used.

Saavedra-Barrera, Rafael H.↗

New Rover Conops with High-Performance Onboard Computing: Give Up Raw Data to Reduce Ops Cost and Do More Science

A major portion of time during the tactical operation of Mars rovers is spent for selecting, prioritizing, and coordinating sciences and engineering activities such that they fit within resource constraints, including the downlink data volume, energy, and time. In particular, the downlink data volume constraint is getting particularly tighter in recent missions because modern instruments produce increasingly high data volume while the communication bandwidth is essentially bounded by the law of physics. Tactical operation would be substantially simplified, hence the operation cost could be reduced, if the data volume constraint is relaxed or even removed. In this abstract, we propose a new operation paradigm for achieving this goal. The key observation is that, both in science and engineering applications, the bit size of raw data is typically much greater than the volume of processed information that is needed for scientific or engineering analysis. For example, a full-resolution image from Mastcam-Z, the main science camera on Perseverance, is about 700 kB in volume and we downlinked 29,685 images up to Sol 243, totaling ~20 GB of data. But of course, scientists do not use every pixel of these images; what they really look for in the images are geological features, typically represented by specific geometric configurations or textures. An end product after processing hundreds of Mascam-Z images could be a single geological map summarizing the spatial distribution of the features. For another example, a 100-meter drive of Perseverance produces 7-12 MB of drive telemetry, which records every detail of the rover's motion at 8 Hz, including position, attitude, steering angles, encoder readings, motor currents and many other information. But what the ground engineers eventually pay attention to is the signs of anomaly, such as excessive motor currents or high slip; if a drive is nominal, the vast majority of this data is unused. What if, then, we process the raw data onboard and only downlink the processed data that is relevant to scientific or engineering analyses, such as a list of detected science features (with cropped images) or a list of potential signs of anomaly while driving? A major roadblock for such onboard, high-level information processing has been the onboard computational resource. RAD750, the main onboard computer of Perseverance, is obviously not sufficient for performing complex image or signal processing such as object detection, semantic segmentation, or anomaly detection. Interestingly, RAD750 is not the best processor that Perseverance has; Qualcomm's Snapdragon 801, a modern mobile processor, is on her Heli Base Station, a device for communicating with Mars Helicopter Ingenuity; also, Intel's Atom E3845 processors are on engineering cameras. In the reminder of this paper, we will introduce two particular uses cases of these high-performance co-processors (meaning auxiliary CPU, GPU, or other types of processors that are separate from the main processor that runs the main flight software) for lowering operation cost and accommodating more science activities for a given communication constraint.

Didier, A.↗

The Effect of Vane-Blade Spacing on Transonic Turbine Stage Performance

This paper presents the results of a computational study on the effect of axial spacing between the vane and blade rows of a transonic turbine stage. The study was performed on the mid-span section of a high-pressure turbine stage using a quasi-3D, unsteady Navier-Stokes solver that provides a fully interactive vane-blade unsteady flow solution. Three different cases were considered, corresponding to axial spacings of 20%, 40%, and 60% of the vane axial chord. The calculated vane and blade pressure distributions for the 40 percent case were found to compare favorably with experimental measurements acquired in a short-duration shock tunnel. In addition, the analysis shows a marked increase in the amplitude of the unsteady pressure fluctuations on the vane and blade surfaces as the spacing decreases. Time-averaged stage adiabatic efficiency predictions for each case are presented to show the effect of spacing on aerodynamic performance.

F J Kelecy↗

A Better ARED Squat

The 0-G ARED squat under loads the legs relative to the 1g ARED squat. In 1g the knee extensor/flexor muscles are primarily engaged due to the body's center of gravity is behind the knees during the motion of the squat. As body weight does not play a sufficient role 0 G, a crewmember's load exposure is limited by the load delivered by ARED through the exercise bar. Prescription loads for lowerbody resistance exercise in microgravity aim to include 1-G exercise bar load in addition to the crewmember's Earth body weight (BW); however, pressure points from the bar and the 1BW increased load at the shoulders translating to higher loads on the back have been a historical limitation for shoulders, requiring a decrease in exercise load at the start of the mission. Analogous to crewmembers, bed rest subjects report limitations of exercising with high loads on the back while performing squats on the horizontal exercise fixture (HEF), a custom exercise device that serves as an analog to 0-G ARED. Improvements for increasing loads on the HEF squat were suggested by distributing total exercise load between the hips and the bar1. The same is recommended for the 0-G ARED squat, with using current equipment on the ISS, which include the T2 running harness and T2 bungees. Quantification of this improvement has been accessed through computational modeling. The purpose of this study is to characterize joint torque during a squat with a distribution in exercise load on the ARED in 0 G. The analysis used existing models from NASA's Digital Astronaut Project. The biomechanics squat model was integrated with the ARED model and T2 bungees. The spring constant for the bungees were derived from ground testing. Forward dynamic simulation was performed for various conditions including anchor point attachments on the footplate of the ARED, bar load, hip load, and gravitational environment. The model confirms joint torques at knees is lower relative to 1G conditions primarily because the load delivery system is just with the exercise bar in 0 G. By distributing partial loads through use of the bungees to the hips joint-torque profiles were altered during a squat and provided options to enhance targeting lower-body loading in aims as for an improved countermeasure.

Caldwell, E. E.↗

Analysis of Saturn's Thermal Emission at 2.2-cm Wavelength: Spatial Distribution of Ammonia Vapor

This work focuses on determining the latitudinal structure of ammonia vapor in Saturn's cloud layer near 1.5 bars using the brightness temperature maps derived from the Cassini RADAR (Elachi et al., 2004) instrument, which works in a passive mode to measure thermal emission from Saturn at 2.2-cm wavelength. We perform an analysis of five brightness temperature maps that span epochs from 2005 to 2011, which are presented in a companion paper by Janssen et al. (2013a, this issue). The brightness temperature maps are representative of the spatial distribution of ammonia vapor, since ammonia gas is the only effective opacity source in Saturn's atmosphere at 2.2-cm wavelength. Relatively high brightness temperatures indicate relatively low ammonia relative humidity (RH), and vice versa. We compare the observed brightness temperatures to brightness temperatures computed using the Juno atmospheric microwave radiative transfer (JAMRT) program which includes both the means to calculate a tropospheric atmosphere model for Saturn and the means to carry out radiative transfer calculations at microwave frequencies. The reference atmosphere to which we compare has a 3x solar deep mixing ratio of ammonia (we use 1.352x10(exp -4) for the solar mixing ratio of ammonia vapor relative to H2; see Atreya, 2010) and is fully saturated above its cloud base. The maps are comprised of residual brightness temperatures-observed brightness temperature minus the model brightness temperature of the saturated atmosphere.

Atmospheres↗

Cooperative Data Sharing: Simple Support for Clusters of SMP Nodes

Libraries like PVM and MPI send typed messages to allow for heterogeneous cluster computing. Lower-level libraries, such as GAM, provide more efficient access to communication by removing the need to copy messages between the interface and user space in some cases. still lower-level interfaces, such as UNET, get right down to the hardware level to provide maximum performance. However, these are all still interfaces for passing messages from one process to another, and have limited utility in a shared-memory environment, due primarily to the fact that message passing is just another term for copying. This drawback is made more pertinent by today's hybrid architectures (e.g. clusters of SMPs), where it is difficult to know beforehand whether two communicating processes will share memory. As a result, even portable language tools (like HPF compilers) must either map all interprocess communication, into message passing with the accompanying performance degradation in shared memory environments, or they must check each communication at run-time and implement the shared-memory case separately for efficiency. Cooperative Data Sharing (CDS) is a single user-level API which abstracts all communication between processes into the sharing and access coordination of memory regions, in a model which might be described as "distributed shared messages" or "large-grain distributed shared memory". As a result, the user programs to a simple latency-tolerant abstract communication specification which can be mapped efficiently to either a shared-memory or message-passing based run-time system, depending upon the available architecture. Unlike some distributed shared memory interfaces, the user still has complete control over the assignment of data to processors, the forwarding of data to its next likely destination, and the queuing of data until it is needed, so even the relatively high latency present in clusters can be accomodated. CDS does not require special use of an MMU, which can add overhead to some DSM systems, and does not require an SPMD programming model. unlike some message-passing interfaces, CDS allows the user to implement efficient demand-driven applications where processes must "fight" over data, and does not perform copying if processes share memory and do not attempt concurrent writes. CDS also supports heterogeneous computing, dynamic process creation, handlers, and a very simple thread-arbitration mechanism. Additional support for array subsections is currently being considered. The CDS1 API, which forms the kernel of CDS, is built primarily upon only 2 communication primitives, one process initiation primitive, and some data translation (and marshalling) routines, memory allocation routines, and priority control routines. The entire current collection of 28 routines provides enough functionality to implement most (or all) of MPI 1 and 2, which has a much larger interface consisting of hundreds of routines. still, the API is small enough to consider integrating into standard os interfaces for handling inter-process communication in a network-independent way. This approach would also help to solve many of the problems plaguing other higher-level standards such as MPI and PVM which must, in some cases, "play OS" to adequately address progress and process control issues. The CDS2 API, a higher level of interface roughly equivalent in functionality to MPI and to be built entirely upon CDS1, is still being designed. It is intended to add support for the equivalent of communicators, reduction and other collective operations, process topologies, additional support for process creation, and some automatic memory management. CDS2 will not exactly match MPI, because the copy-free semantics of communication from CDS1 will be supported. CDS2 application programs will be free to carefully also use CDS1. CDS1 has been implemented on networks of workstations running unmodified Unix-based operating systems, using UDP/IP and vendor-supplied high- performance locks. Although its inter-node performance is currently unimpressive due to rudimentary implementation technique, it even now outperforms highly-optimized MPI implementation on intra-node communication due to its support for non-copy communication. The similarity of the CDS1 architecture to that of other projects such as UNET and TRAP suggests that the inter-node performance can be increased significantly to surpass MPI or PVM, and it may be possible to migrate some of its functionality to communication controllers.

DiNucci, David C.↗

Experimental verification of a computational procedure for the design of TWT-refocuser-MDC systems

A comparison of analytical and experimental results is presented for a high performance dual-mode helix TWT, equipped with multistage depressed collectors (MDC), and operated over conditions ranging from saturation to the linear regime. The computations are carried out with advanced multidimensional computer programs which model the electron beam as a series of disks or rings of charge and follow their trajectories from the RF input of the TWT, through the slow-wave structure, through the refocusing system, to their points of impact in the depressed collector. TWT performance, collector efficiency, and collector current distribution are computed and compared with measurements. Very good agreement is obtained between computed and measured TWT performance and collector efficiencies. The analytical techniques were subsequently applied to the design of a smaller MDC of nearly equal efficiency.

Dayton, J. A., Jr.↗

RAMP - A fault tolerant distributed microcomputer structure for aircraft navigation and control

Design methodologies for realizing future high authority autoflight control systems are being investigated, taking into account also the study of distributed microcomputer architectures. Attention is given to the redundant asynchronous microprocessor (RAMP) structure. RAMP comprises a connected network of microcomputers which has as input command and sensor information, and which generates servo information to drive actuators, and thrust linkages. Tolerance to hardware failures is achieved by static redundancy. Results of a failed microcomputer are simply rejected. This is done in lieu of dynamic redundancy wherein the distributed computer system performs real time fault detection and reconfiguration of the system. Attention is given to the RAMP network structure and operation, flight control with parallel asynchronous computers, and intermittent fault tolerance.

Dunn, W. R.↗

Load-Following Power Timeline Analyses for the International Space Station

Spacecraft are typically complex assemblies of interconnected systems and components that have highly time-varying thermal communications, and power requirements. It is essential that systems designers be able to assess the capability of the spacecraft to meet these requirements which should represent a realistic projection of demand for these resources once the vehicle is on-orbit. To accomplish the assessment from the power standpoint, a computer code called ECAPS has been developed at NASA Lewis Research Center that performs a load-driven analysis of a spacecraft power system given time-varying distributed loading and other mission data. This program is uniquely capable of synthesizing all of the changing spacecraft conditions into a single, seamless analysis for a complete mission. This paper presents example power load timelines with which numerous data are integrated to provide a realistic assessment of the load-following capabilities of the power system. Results of analyses show how well the power system can meet the time-varying power resource demand.

Fincannon, James↗

Refined Zigzag Theory for Homogeneous, Laminated Composite, and Sandwich Plates: A Homogeneous Limit Methodology for Zigzag Function Selection

The Refined Zigzag Theory (RZT) for homogeneous, laminated composite, and sandwich plates is presented from a multi-scale formalism starting with the inplane displacement field expressed as a superposition of coarse and fine contributions. The coarse kinematic field is that of first-order shear-deformation theory, whereas the fine kinematic field has a piecewise-linear zigzag distribution through the thickness. The condition of limiting homogeneity of transverse-shear properties is proposed and yields four distinct sets of zigzag functions. By examining elastostatic solutions for highly heterogeneous sandwich plates, the best-performing zigzag functions are identified. The RZT predictive capabilities to model homogeneous and highly heterogeneous sandwich plates are critically assessed, demonstrating its superior efficiency, accuracy ; and a wide range of applicability. The present theory, which is derived from the virtual work principle, is well-suited for developing computationally efficient CO-continuous finite elements, and is thus appropriate for the analysis and design of high-performance load-bearing aerospace structures.

Tessler, Alexander↗

Modeling the Effective Elasticity of Anisotropic Porous Materials

The development and optimization of composite materials designed for thermal protection of NASA’s spacecraft require understanding their physical response to high-enthalpy environments. To predict their macro-scale properties and behavior, high-fidelity 3D simulations are performed at the microscale on realistic representations of these composites. The digital microstructures are generated either synthetically or through X-ray micro-computed tomography reconstructions. One of the main challenges in the prediction of the structural response of heatshield materials is the computation of the effective elasticity of the fibrous composite, as well as the understanding of the deformation and stresses generated at the microscale. These are driven by the fiber layout within the microstructure and the distribution of the infused matrix. In this effort, the micro-mechanical linear elastic behavior of fibrous ablators is modeled using a numerical method based on the Multi-Point Stress Approximation (MPSA) finite volume scheme, a generalization of the more commonly used Multi-Point Flux Approximation (MPFA) that was presented at the 10th Ablation Workshop. To predict the behavior of fibrous and woven architectures, algorithms that compute the local fiber orientation are used. The implementation of the MPSA was verified using analytical solutions, engineering test cases, and compared against legacy Finite Element Analysis (FEA) software. The stress analysis models were then applied to real geometries used by NASA in thermal protection systems such as fibrous preforms and woven materials and the results were compared to experimental data.

Elasticity↗

Design and implementation of scalable tape archiver

In order to reduce costs, computer manufacturers try to use commodity parts as much as possible. Mainframes using proprietary processors are being replaced by high performance RISC microprocessor-based workstations, which are further being replaced by the commodity microprocessor used in personal computers. Highly reliable disks for mainframes are also being replaced by disk arrays, which are complexes of disk drives. In this paper we try to clarify the feasibility of a large scale tertiary storage system composed of 8-mm tape archivers utilizing robotics. In the near future, the 8-mm tape archiver will be widely used and become a commodity part, since recent rapid growth of multimedia applications requires much larger storage than disk drives can provide. We designed a scalable tape archiver which connects as many 8-mm tape archivers (element archivers) as possible. In the scalable archiver, robotics can exchange a cassette tape between two adjacent element archivers mechanically. Thus, we can build a large scalable archiver inexpensively. In addition, a sophisticated migration mechanism distributes frequently accessed tapes (hot tapes) evenly among all of the element archivers, which improves the throughput considerably. Even with the failures of some tape drives, the system dynamically redistributes hot tapes to the other element archivers which have live tape drives. Several kinds of specially tailored huge archivers are on the market, however, the 8-mm tape scalable archiver could replace them. To maintain high performance in spite of high access locality when a large number of archivers are attached to the scalable archiver, it is necessary to scatter frequently accessed cassettes among the element archivers and to use the tape drives efficiently. For this purpose, we introduce two cassette migration algorithms, foreground migration and background migration. Background migration transfers cassettes between element archivers to redistribute frequently accessed cassettes, thus balancing the load of each archiver. Background migration occurs the robotics are idle. Both migration algorithms are based on access frequency and space utility of each element archiver. To normalize these parameters according to the number of drives in each element archiver, it is possible to maintain high performance even if some tape drives fail. We found that the foreground migration is efficient at reducing access response time. Beside the foreground migration, the background migration makes it possible to track the transition of spatial access locality quickly.

Nemoto, Toshihiro↗

Aviation Safety Modeling and Simulation (ASMM) Propulsion Fleet Modeling: A Tool for Semi-Automatic Construction of CORBA-based Applications from Legacy Fortran Programs

Within NASA's Aviation Safety Program, NASA GRC participates in the Modeling and Simulation Project called ASMM. NASA GRC s focus is to characterize the propulsion systems performance from a fleet management and maintenance perspective by modeling and through simulation predict the characteristics of two classes of commercial engines (CFM56 and GE90). In prior years, the High Performance Computing and Communication (HPCC) program funded, NASA Glenn in developing a large scale, detailed simulations for the analysis and design of aircraft engines called the Numerical Propulsion System Simulation (NPSS). Three major aspects of this modeling included the integration of different engine components, coupling of multiple disciplines, and engine component zooming at appropriate level fidelity, require relatively tight coupling of different analysis codes. Most of these codes in aerodynamics and solid mechanics are written in Fortran. Refitting these legacy Fortran codes with distributed objects can increase these codes reusability. Aviation Safety s modeling and simulation use in characterizing fleet management has similar needs. The modeling and simulation of these propulsion systems use existing Fortran and C codes that are instrumental in determining the performance of the fleet. The research centers on building a CORBA-based development environment for programmers to easily wrap and couple legacy Fortran codes. This environment consists of a C++ wrapper library to hide the details of CORBA and an efficient remote variable scheme to facilitate data exchange between the client and the server model. Additionally, a Web Service model should also be constructed for evaluation of this technology s use over the next two- three years.

Sang, Janche↗

Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Technology Development Overview

The successful flight of the Inflatable Reentry Vehicle Experiment (IRVE)-3 has further demonstrated the potential value of Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. This technology development effort is funded by NASA's Space Technology Mission Directorate (STMD) Game Changing Development Program (GCDP). This paper provides an overview of a multi-year HIAD technology development effort, detailing the projects completed to date and the additional testing planned for the future. The effort was divided into three areas: Flexible Systems Development (FSD), Mission Advanced Entry Concepts (AEC), and Flight Validation. FSD consists of a Flexible Thermal Protection Systems (FTPS) element, which is investigating high temperature materials, coatings, and additives for use in the bladder, insulator, and heat shield layers; and an Inflatable Structures (IS) element which includes manufacture and testing (laboratory and wind tunnel) of inflatable structures and their associated structural elements. AEC consists of the Mission Applications element developing concepts (including payload interfaces) for missions at multiple destinations for the purpose of demonstrating the benefits and need for the HIAD technology as well as the Next Generation Subsystems element. Ground test development has been pursued in parallel with the Flight Validation IRVE-3 flight test. A larger scale (6m diameter) HIAD inflatable structure was constructed and aerodynamically tested in the National Full-scale Aerodynamics Complex (NFAC) 40ft by 80ft test section along with a duplicate of the IRVE-3 3m article. Both the 6m and 3m articles were tested with instrumented aerodynamic covers which incorporated an array of pressure taps to capture surface pressure distribution to validate Computational Fluid Dynamics (CFD) model predictions of surface pressure distribution. The 3m article also had a duplicate IRVE-3 Thermal Protection System (TPS) to test in addition to testing with the Aerocover configuration. Both the Aerocovers and the TPS were populated with high contrast targets so that photogrammetric solutions of the loaded surface could be created. These solutions both refined the aerodynamic shape for CFD modeling and provided a deformed shape to validate structural Finite Element Analysis (FEA) models. Extensive aerothermal testing has been performed on the TPS candidates. This testing has been conducted in several facilities across the country. The majority of the testing has been conducted in the Boeing Large Core Arc Tunnel (LCAT). HIAD is continuing to mature testing methodology in this facility and is developing new test sample fixtures and control methodologies to improve understanding and quality of the environments to which the samples are subjected. Additional testing has been and continues to be performed in the NASA LaRC 8ft High Temperature Tunnel, where samples up to 2ft by 2ft are being tested over representative underlying structures incorporating construction features such as sewn seams and through-thickness quilting. With the successful completion to the IRVE-3 flight demonstration, mission planning efforts are ramping up on the development of the HIAD Earth Atmospheric Reenty Test (HEART) which will demonstrate a relevant scale vehicle in relevant environments via a large-scale aeroshell (approximately 8.5m) entering at orbital velocity (approximately 7km/sec) with an entry mass on the order of 4MT. Also, the Build to Print (BTP) hardware built as a risk mitigation for the IRVE-3 project to have a "spare" ready to go in the event of a launch vehicle delivery failure is now available for an additional sub-orbital flight experiment. Mission planning is underway to define a mission that can utilize this existing hardware and help the HIAD project further mature this technology.

Hughes, Stephen J.↗

Programming methodology for a general purpose automation controller

The General Purpose Automation Controller is a multi-processor architecture for automation programming. A methodology has been developed whose aim is to simplify the task of programming distributed real-time systems for users in research or manufacturing. Programs are built by configuring function blocks (low-level computations) into processes using data flow principles. These processes are activated through the verb mechanism. Verbs are divided into two classes: those which support devices, such as robot joint servos, and those which perform actions on devices, such as motion control. This programming methodology was developed in order to achieve the following goals: (1) specifications for real-time programs which are to a high degree independent of hardware considerations such as processor, bus, and interconnect technology; (2) a component approach to software, so that software required to support new devices and technologies can be integrated by reconfiguring existing building blocks; (3) resistance to error and ease of debugging; and (4) a powerful command language interface.

Sturzenbecker, M. C.↗

Interfacial Structure and Capacitance of Li-doped Ionic Liquid Electrolytes from Molecular Simulations

Ionic liquids have been proposed as candidate electrolytes for high-energy density, rechargeable batteries, supercapacitors, and hybrid energy storage devices. Though Li-salt is often present in these systems, its influence on interfacial properties is largely uncharacterized. We, thereby, present an extensive computational analysis, supported by experimental comparisons, of the properties of a representative set of these electrolytesat an ideal carbon interface as a function of Li-salt doping and voltage. We have performed polarizable molecular (MD) dynamics simulations, using the APPLEP force field, to evaluate electric double layer (EDL) capacitance and distribution of Li+ in the EDL. Differential capacitance exhibits the characteristic camel profile and is insensitive to Li-doping. Li+ localizes in the second molecular layer of the EDL, which is a result of confinement from free energy barriers associated with ion layering. Joint MDelectronic structure computations show the electrochemical window of the electrolytes to be a weak function of Li-doping. Estimates of supercapacitor specific energy are made using the computed window and capacitance. The magnitude and trends in specific energy are in good agreement with experiment.

batteries↗