Search NASA⌕ Search

SEARCH · Search NASA

Results for “interferometric techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Interferometric Characterization of the Earth's Atmosphere from Lagrange Point 2

Part of the NASA plans for future Earth-Science missions calls for observations using novel vantage points that can produce science products otherwise unobtainable. Observations of the Earth from the Lagrange-2 point, L-2, (1.5 million kilometers behind the Earth on the Earth-Sun line) affords a unique vantage point for atmospheric science. Special observation of the Earth's atmosphere using solar occultation techniques in the near infrared (1 to 4 microns) provides one of the most accurate method of passively sensing altitude profiles of the major species (CO2, O3, O2, CH4, H2O, N2O). In addition to observation of the Earth's atmosphere, it will be possible to observe a portion of the solar disk at moderate spatial resolution without interference from the Earth.

Herman, J. R.↗
NASA NTRS1975

A statistical technique for processing radio interferometer data

The output of a radio interferometer is the Fourier transform of the object under investigation. Due to the limited coverage of the Fourier plane, the reconstruction of the image of the source is blurred by the beam of the synthesized array. A maximum-likelihood processing technique is described which uses the statistical properties of the received noise-like signals. This technique has been used extensively in the processing of large-aperture seismic arrays. This inversion method results in a synthesized beam that is more uniform, has lower sidelobes, and higher resolution than the normal Fourier transform methods. The maximum-likelihood method algorithm was applied successfully to very long baseline and short baseline interferometric data.

Papadopoulos, G. D.↗
NASA NTRS2000

Topographic Map Generation from the Shuttle Radar Topography Mission C-band SCANSAR Interferometry

A highly accurate global topographic map of the Earth's surface has been an elusive goal for at least three decades that may soon be achieved with the newly acquired Shuttle Radar Topographic Mission (SRTM) data. SRTM collected data for 99.97% of the Earth's landmass between -57 degrees and 60 degrees latitude during a 11 day mission in February, 2000. A modified version of the SIR-C radar that previously flew on the shuttle in 1994 augmented with a radar mounted on a 62 m boom was used to collect radar interferometric data at C (5.6 cm wavelength) and X (3 cm wavelength) bands. The C-band radar was operated in the SCANSAR mode in order to extend the swath width to 225 km the minimal amount required to achieve contiguous coverage at the equator. This paper presents an overview of the new algorithms and techniques used to process the SCANSAR data to digital elevation maps. First results of topographic maps generated from the SRTM data are used to illustrate the techniques described in this paper.

Hensley, Scott↗
NASA NTRS2016

Ground-Level Digital Terrain Model (DTM) Construction from Tandem-X InSAR Data and Worldview Stereo-Photogrammetric Images

The ground-level digital elevation model (DEM) or digital terrain model (DTM) information are invaluable for environmental modeling, such as water dynamics in forests, canopy height, forest biomass, carbon estimation, etc. We propose to extract the DTM over forested areas from the combination of interferometric complex coherence from single-pass TanDEM-X (TDX) data at HH polarization and Digital Surface Model (DSM) derived from high-resolution WorldView (WV) image pair by means of random volume over ground (RVoG) model. The RVoG model is a widely and successfully used model for polarimetric SAR interferometry (Pol-InSAR) technique for vertical forest structure parameter retrieval [1][2][3][4]. The ground-level DEM have been obtained by complex volume decorrelation in the RVoG model with the DSM using stereo-photogrammetric technique. Finally, the airborne lidar data were used to validate the ground-level DEM and forest canopy height results.

Lee, Seung-Kuk↗
NASA NTRS1993

Two microstrip arrays for interferometric SAR applications

Two types of C-band aircraft interferometric Synthetic Aperture Radar (SAR) are being developed at JPL to measure the ocean wave characteristics. Each type requires two identical antennas with each having a long rectangular aperture to radiate fan-shaped beam(s). One type of these radars requires each of its antennas to radiate a broadside beam that will measure the target's cross-track velocity. The other type, having each of its antennas to radiate two off-broadside pointed beams, will allow the measurement of both the cross-track and the along-track velocities of the target. Because flush mounting of the antenna on the aircraft fuselage is desirable, microstrip patch array is selected for these interferometric SAR antennas. To meet the radar system requirement, each array needs a total of 76 microstrip patches which are arranged in a 38 x 2 rectangular aperture with a physical size of 1.6m x 16.5cm. To minimize the insertion loss and physical real estate of this relatively long array, a combined series/parallel feed technique is used. Techniques to suppress cross-pol radiation and to effectively utilize the RF power are also implemented. Cross-pol level of lower than -30 dB from the co-pol peak and low insertion loss of 0.36 dB have been achieved for both types of arrays. For the type of radar that requires two off-braodside pointed beams, a simple phasing technique is used to achieve this dual-beam capability with adequate antenna gain (20 dBi) and sidelobe level (-14 dB). Both radar arrays have been flight tested on aircraft with excellent antenna performance demonstrated.

Huang, J.↗
NASA NTRS1987

Microgravity research applications of interferometry to heat and mass transfer

Major space flight experiments which have used interferometric measurement as a major support system are described together with similar ground-based research. Space experiments include those flown on Spacelab 3 ad on the D-1 mission. Included in the ground-based experiments are aircraft studies, Spacelab 3 data reduction and evaluation, and supportive laboratory hardware development. It is shown that optical measurement techniques are crucial to microgravity research.

Owen, Robert B.↗
NASA NTRS1973

Radio interferometry for international study of the earthquake mechanism

Consideration of the possibility of developing an improved technique for measuring crustal deformations over distances of hundreds to thousands of kilometers to even intercontinental distances. Attention is focused on the uses of very long baseline interferometry in the structuring of a transportable radio interferometer system capable of high-accuracy three-dimensional earth surveying. In particular, the essential elements of a system called astronomical radio interferometric earth surveying are described. This system involves the use of a pair of antennas, one fixed and one portable, which simultaneously receive random radio signals emitted from an extragalactic radio source. A combination of a readily transportable small-diameter dish for use during a limited period at a remote site with a larger-diameter antenna with a better receiver is recommended.

Macdoran, P. F.↗
NASA NTRS1993

Interferometric tracking system for the tracking and data relay satellite

This report documents construction and testing of the Interferometric Tracking System project developed under the NASA SBIR contract NAS5-30313. Manuals describing the software and hardware, respectively entitled: 'Field Station Guide to Operations' and 'Field Station Hardware Manual' are included as part of this final report. The objective of this contract was to design, build, and operate a system of three ground stations using Very Long Baseline Interferometry techniques to measure the TDRS orbit. The ground stations receive signals from normal satellite traffic, store these signals in co-located computers, and transmit the information via phone lines to a central processing site which correlates the signals to determine relative time delays. Measurements from another satellite besides TDRS are used to determine clock offsets. A series of such measurements will ultimately be employed to derive the orbital parameters, yielding positions accurate to within 50 meters or possibly better.

Effland, John E.↗
NASA NTRS1989

Laser holographic interferometric measurements of the flow in a scramjet inlet at Mach 4

The need for quantitative data is addressed by laser holographic interferometry (LHI) by efficiently recording and reducing high resolution density data. This paper investigates the potential to get quantitative data from an interferogram created from two separate holographic plates. THe LHI measurements were made on a scramjet inlet at Mach 4. LHI successfully generated results for both internal and external flows, and demonstrated its ability to map entire flow fields. Of the three data reduction techniques used, the four-bucket method gave better results than the three-bucket or three-by-three methods. This technique requires high quality holograms as well as a good resolution in the digital images to produce good data.

Mcarthur, J. Craig↗
NASA NTRS1999

Calibration of the Geosar Dual Frequency Interferometric SAR

GeoSAR is an airborne, interferometric Synthetic Aperture Radar (INSAR) system for terrain mapping, currently under development by a consortium including NASA's Jet Propulsion Laboratory (JPL), Calgis, Inc., and the California Department of Conservation (CalDOC) with funding provided by the Topographic Engineering Center (TEC) of the U.S. Army Corps of Engineers and the Defense Advanced Research Projects Agency (DARPA). The radar simultaneously maps swaths on both sides of the aircraft at two frequencies, X-Band and P-Band. For the P-Band system, data is collected for two across track interferometric baselines and at the crossed polarization. The aircraft position and attitude are measured using two Honeywell Embedded GPS Inertial Navigation Units (EGI) and an Ashtech Z12 GPS receiver. The mechanical orientation and position of the antennas are actively measured using a Laser Baseline Metrology System (LBMS). In the GeoSAR motion measurement software, these data are optimally combined with data from a nearby ground station using Ashtech PNAV software to produce the position, orientation, and baseline information are used to process the dual frequency radar data. Proper calibration of the GeoSAR system is essential to obtaining digital elevation models (DEMS) with the required sub-meter level planimetric and vertical accuracies. Calibration begins with the determination of the yaw and pitch biases for the two EGI units. Common range delays are determined for each mode, along with differential time and phase delays between channels. Because the antennas are measured by the LBMS, baseline calibration consists primarily of measuring a constant offset between mechanical center and the electrical phase center of the antennas. A phase screen, an offset to the interferometric phase difference which is a function of absolute phase, is applied to the interferometric data to compensate for multipath and leakage. Calibration parameters are calculated for each of the ten processing modes, each of the operational bandwidths (80 and 160 MHZ), and each aircraft altitude. In this talk we will discuss the layout calibration sites, the synthesis of data from multiple flights to improve the calibration, methods for determining time and phase delays, and techniques for determining radiometric and polarimetric quantities. We will describe how calibration quantities are incorporated into the processor and pre-processor. We will demonstrate our techniques applied to GeoSar data and assess the stability and accuracy of the calibration. This will be compared to the modeled performance determined from calibrating the output of a point target simulator. The details of baseline determination and phase screen calculation are covered in related talks.

Chapine, Elaine↗
NASA NTRS2011

Grazing Incidence Wavefront Sensing and Verification of X-Ray Optics Performance

Evaluation of interferometrically measured mirror metrology data and characterization of a telescope wavefront can be powerful tools in understanding of image characteristics of an x-ray optical system. In the development of soft x-ray telescope for the International X-Ray Observatory (IXO), we have developed new approaches to support the telescope development process. Interferometrically measuring the optical components over all relevant spatial frequencies can be used to evaluate and predict the performance of an x-ray telescope. Typically, the mirrors are measured using a mount that minimizes the mount and gravity induced errors. In the assembly and mounting process the shape of the mirror segments can dramatically change. We have developed wavefront sensing techniques suitable for the x-ray optical components to aid us in the characterization and evaluation of these changes. Hartmann sensing of a telescope and its components is a simple method that can be used to evaluate low order mirror surface errors and alignment errors. Phase retrieval techniques can also be used to assess and estimate the low order axial errors of the primary and secondary mirror segments. In this paper we describe the mathematical foundation of our Hartmann and phase retrieval sensing techniques. We show how these techniques can be used in the evaluation and performance prediction process of x-ray telescopes.

Saha, Timo T.↗
NASA NTRS1991

An electrically scanned thinned array radiometer for Earth remote sensing

Interferometric aperture synthesis is being investigated as an alternative to real aperture measurements of the brightness temperature of the earth from low earth orbit. Aperture synthesis allows for the realization of space borne microwave systems with attractive spatial resolution characteristics. Radio astronomers have performed aperture synthesis by cross-correlating spatially separated antenna element pairs for some time. The application of this technique to the observation of a distributed source, as opposed to a point source in radio astronomy, presents a novel and challenging application of aperture synthesis. The demonstration of this geophysical application of aperture synthesis was carried out by constructing and flight testing a phototype instrument, the Electrically Scanned Thinned Array Radiometer (ESTAR). The subsequent data analysis and image reconstruction yielded an image of the eastern shore of Virginia. In the past year, more data of the same region were taken and analyzed, as well as for other regions of Virginia, Pennsylvania, and Maine. Improvements were made in the image reconstruction technique and in the system electronics for the current and upcoming instruments (ESTAR00 and ESTAR0, respectively), particularly in terms of calibration instrumentation and techniques.

Griffis, Andrew J.↗
NASA NTRS1978

Structure and evolution of solar radio bursts at 26.4 MHz

Results are reported for multiple-baseline interferometric measurements of type II, III, IV, and V solar radio bursts at 26.4 MHz. Thirty-two burst events in a two-month period are analyzed by fitting a double-Gaussian two-dimensional source-brightness distribution model to the observed interferometer visibility function. The multibaseline time-sharing interferometer system employed is described in detail, the model-fitting technique is outlined, and values of the model-fit parameters are given for all 32 cases, which include two type II bursts, three type IV bursts, 17 type III bursts, seven type V bursts, and three bursts of type III, V pairs. The temporal evolution of source structure, size, and motion is examined for the different burst types. The core-halo source structure for the type III bursts is interpreted in comparison to two models, one of which assumes scattering and refraction of a point source while the other postulates primarily refraction from an ensemble of sources distributed over a wide sector in solar longitude.

Chen, H. S.-L.↗
NASA NTRS2018

Digital Beamforming Based RFI Mitigation for Synthetic Aperture Radar

An increasing challenge for P-band Synthetic Aperture Radar (SAR) is Radio Frequency Interference (RFI). RFI results in image distortions and degrades the derived science products. This makes it critical to apply RFI removal techniques to restore the image quality. New advanced techniques can be achieved with Digital Beamforming (DBF) radars such as EcoSAR. In this paper, we present a Range-Dependent Time Minimum Variance Distortionless Response (RDTMVDR) Beamformer and apply it to EcoSAR flight data during post-processing. The antenna pattern (AP) is adaptively changed for each range line which increases the RFI suppression compared to a fixed AP for each pulse. The interferometric image quality is assessed before and after RFI suppression.

Bollian, Tobias↗
NASA NTRSDate not supplied

Estimating Forest Stand Height in Savannakhet, Lao PDR Using InSAR and Backscatter Methods with L-Band SAR Data

Forest stand height (FSH), or average canopy height, serves as an important indicator for forest monitoring. The information provided about above ground biomass for greenhouse gas emissions reporting, and estimating carbon storage is relevant for reporting for Reducing Emissions from Deforestation and Forest Degradation (REDD+). A novel forest height estimation method utilizing a fusion of backscatter and Interferometric Synthetic Aperture Radar (InSAR) data from JAXA’s Advanced Land Observing Satellite Phased Array type L-band Synthetic Aperture Radar (ALOS PALSAR) are applied to a use case in Savannakhet, Lao. Compared with LiDAR, the estimated height from the fusion method had an RMSE of 4.90 m and an R2 of 0.26. These results are comparable to previous studies using SAR estimation techniques. Despite limitations of data quality and quantity, the Savannakhet, Lao use case demonstrates the applicability of these techniques utilizing L-band SAR data for estimating FSH in tropical forests and can be used as a springboard for use of L-band data from the future NASA-ISRO SAR (NISAR) mission.

remote sensing↗
NASA NTRS1978

Two-scale-factor universality near the critical point of fluids

Thermodynamic data from interferometric density profile studies and light-scattering experiments near the critical isochore of Xe, CO2 and SF6 provide a basis for examining the hypothesized two-scale-factor universality for the correlation function of fluids near the gas-liquid critical point. For the investigation, three-scale-factor universality is assumed, with Ising-like critical exponent values obtained through the renormalization group technique. The two thermodynamic scale factors are found from the density profiles, while the scale factor for the correlation length is obtained from the light-scattering data.

Sengers, J. V.↗
NASA NTRS2020

Residual Motion Estimation for Multi-Squint Airborne SAR

Airborne SAR data are often challenging to analyze due tothe limited accuracy of the platform motion measurements.In interferometric scenarios, even small residual motion er-rors cause undesirable artifacts in the interferometric phaseand geometric registration of image pairs. Various calibrationtechniques have been developed, often exploiting spectral di-versity in some way. The UAVSAR L-band system has imple-mented a new operating mode where multiple images are ac-quired simultaneously at different azimuth squint angles, pro-viding enhanced opportunities for motion calibration. Thispaper describes this imaging mode and the residual motioncalibration technique developed for these special data sets.

Hawkins, Brian↗
NASA NTRS1984

Nonintrusive optical single-particle counter for measuring the size and velocity of droplets in a spray

A technique for measuring nonintrusively, and in real time, the size and velocity of droplets in a spray is presented. A small beam identifies the center of a larger beam, thus defining a region of almost uniform intensity, and only droplets crossing through such a center are measured. The size is obtained from the absolute scattered light and the velocity from the modulated signal produced by the interferometric pattern. A self-calibrating algorithm is also discussed. Results are presented for a spray of predictable chracteristics.

Hess, C. F.↗