SEARCH · Search NASA

Results for “lidar error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Simultaneous Laser Ranging and Communication from an Earth-Based Satellite Laser Ranging Station to the Lunar Reconnaissance Orbiter in Lunar Orbit

We report a free space laser communication experiment from the satellite laser ranging (SLR) station at NASA Goddard Space Flight Center (GSFC) to the Lunar Reconnaissance Orbiter (LRO) in lunar orbit through the on board one-way Laser Ranging (LR) receiver. Pseudo random data and sample image files were transmitted to LRO using a 4096-ary pulse position modulation (PPM) signal format. Reed-Solomon forward error correction codes were used to achieve error free data transmission at a moderate coding overhead rate. The signal fading due to the atmosphere effect was measured and the coding gain could be estimated.

fee-space optical communication↗

NASA NTRS1989

Estimations of ABL fluxes and other turbulence parameters from Doppler lidar data

Techniques for extraction boundary layer parameters from measurements of a short-pulse CO2 Doppler lidar are described. The measurements are those collected during the First International Satellites Land Surface Climatology Project (ISLSCP) Field Experiment (FIFE). By continuously operating the lidar for about an hour, stable statistics of the radial velocities can be extracted. Assuming that the turbulence is horizontally homogeneous, the mean wind, its standard deviations, and the momentum fluxes were estimated. Spectral analysis of the radial velocities is also performed from which, by examining the amplitude of the power spectrum at the inertial range, the kinetic energy dissipation was deduced. Finally, using the statistical form of the Navier-Stokes equations, the surface heat flux is derived as the residual balance between the vertical gradient of the third moment of the vertical velocity and the kinetic energy dissipation. Combining many measurements would normally reduce the error provided that, it is unbiased and uncorrelated. The nature of some of the algorithms however, is such that, biased and correlated errors may be generated even though the raw measurements are not. Data processing procedures were developed that eliminate bias and minimize error correlation. Once bias and error correlations are accounted for, the large sample size is shown to reduce the errors substantially. The principal features of the derived turbulence statistics for two case studied are presented.

Gal-Chen, Tzvi↗

NASA NTRS2012

Height and Biomass of Mangroves in Africa from ICEsat/GLAS and SRTM

The accurate quantification of forest 3-D structure is of great importance for studies of the global carbon cycle and biodiversity. These studies are especially relevant in Africa, where deforestation rates are high and the lack of background data is great. Mangrove forests are ecologically significant and it is important to measure mangrove canopy heights and biomass. The objectives of this study are to estimate: 1. The total area, 2. Canopy height distributions and 3. Aboveground biomass of mangrove forests in Africa. To derive mangrove 3-D structure and biomass maps, we used a combination of mangrove maps derived from Landsat ETM+, LiDAR canopy height estimates from ICEsat/GLAS (Ice, Cloud, and land Elevation Satellite/Geoscience Laser Altimeter System) and elevation data from SRTM (Shuttle Radar Topography Mission) for the African continent. More specifically, we extracted mangrove forest areas on the SRTM DEM using Landsat based landcover maps. The LiDAR (Light Detection and Ranging) measurements from the large footprint GLAS sensor were used to derive local estimates of canopy height and calibrate the Interferometric Synthetic Aperture Radar (InSAR) data from SRTM. We then applied allometric equations relating canopy height to biomass in order to estimate above ground biomass (AGB) from the canopy height product. The total mangrove area of Africa was estimated to be 25 960 square kilometers with 83% accuracy. The largest mangrove areas and greatest total biomass was 29 found in Nigeria covering 8 573 km2 with 132 x10(exp 6) Mg AGB. Canopy height across Africa was estimated with an overall root mean square error of 3.55 m. This error also includes the impact of using sensors with different resolutions and geolocation error which make comparison between measurements sensitive to canopy heterogeneities. This study provides the first systematic estimates of mangrove area, height and biomass in Africa. Our results showed that the combination of ICEsat/GLAS and SRTM data is well suited for vegetation 3-D mapping on a continental scale.

Fatoyinbo, Temilola E.↗

NASA NTRS1992

A considerable effect of stratospheric aerosol on lidar-detected ozone profile and a three-wavelength inversion technique for both ozone and aerosol

As far as the Differential Absorption Lidar (DIAL) technique is concerned, it is important that the off-line wavelength is close to the on-line wavelength in order to avoid a messy computation of the atmospheric aerosol scattering. However, the two wavelengths of ozone-DIAL are usually considerably different. Usually, an excimer laser of 308nm (on-line) and Raman shifting of 353nm or the third harmonic of a Nd-YAG laser with 355nm (off-line) are selected for measurements of the stratospheric ozone, and there is a difference of 45nm or 47nm between them. Because of the difference there is a difference in the atmospheric scatterings of the two wavelengths. This can cause some error in the retrieved ozone profile if the aerosol scattering is neglected. This paper is devoted to a study of the effect of the stratospheric aerosol on the ozone solution, and a three-wavelength detection technique is proposed for obtaining the more exact ozone profile and the aerosol profile in the stratosphere.

Qiu, Jinhuan↗

NASA NTRS2010

Remote Characterization of Biomass Measurements: Case Study of Mangrove Forests

Accurately quantifying forest biomass is of crucial importance for climate change studies. By quantifying the amount of above and below ground biomass and consequently carbon stored in forest ecosystems, we are able to derive estimates of carbon sequestration, emission and storage and help close the carbon budget. Mangrove forests, in addition to providing habitat and nursery grounds for over 1300 animal species, are also an important sink of biomass. Although they only constitute about 3% of the total forested area globally, their carbon storage capacity -- in forested biomass and soil carbon -- is greater than that of tropical forests (Lucas et al, 2007). In addition, the amount of mangrove carbon -- in the form of litter and leaves exported into offshore areas is immense, resulting in over 10% of the ocean's dissolved organic carbon originating from mangroves (Dittmar et al, 2006) The measurement of forest above ground biomass is carried out on two major scales: on the plot scale, biomass can be measured using field measurements through allometric equation derivation and measurements of forest plots. On the larger scale, the field data are used to calibrate remotely sensed data to obtain stand-wide or even regional estimates of biomass. Currently, biomass can be calculated using average stand biomass values and optical data, such as aerial photography or satellite images (Landsat, Modis, Ikonos, SPOT, etc.). More recent studies have concentrated on deriving forest biomass values using radar (JERS, SIR-C, SRTM, Airsar) and/or lidar (ICEsat/GLAS, LVIS) active remote sensing to retrieve more accurate and detailed measurements of forest biomass. The implementation of a generation of new active sensors (UAVSar, DesdynI, Alos/Palsar, TerraX) has prompted the development of new tecm'liques of biomass estimation that use the combination of multiple sensors and datasets, to quantify past, current and future biomass stocks. Focusing on mangrove forest biomass estimation, this book chapter has 3 main objectives: a) To describe in detail the field methodologies used to derive accurate estimates of biomass in mangrove forests b) To explain how mangrove forest biomass can be measured using several remote sensing techniques and datasets c) To give a detailed explanation of the measurement challenges and errors that arise in each estimate of forest biomass

Fatoyinbo, Temilola E.↗

NASA NTRS2012

Tele-Operated Lunar Rover Navigation Using Lidar

Near real-time tele-operated driving on the lunar surface remains constrained by bandwidth and signal latency despite the Moon s relative proximity. As part of our work within NASA s Human-Robotic Systems Project (HRS), we have developed a stand-alone modular LIDAR based safeguarded tele-operation system of hardware, middleware, navigation software and user interface. The system has been installed and tested on two distinct NASA rovers-JSC s Centaur2 lunar rover prototype and ARC s KRex research rover- and tested over several kilometers of tele-operated driving at average sustained speeds of 0.15 - 0.25 m/s around rocks, slopes and simulated lunar craters using a deliberately constrained telemetry link. The navigation system builds onboard terrain and hazard maps, returning highest priority sections to the off-board operator as permitted by bandwidth availability. It also analyzes hazard maps onboard and can stop the vehicle prior to contacting hazards. It is robust to severe pose errors and uses a novel scan alignment algorithm to compensate for attitude and elevation errors.

Pedersen, Liam↗

NASA NTRS2002

Airborne Sunphotometer Measurements of Aerosol Optical Depth and Water Vapor in ACE-Asia and Their Comparisons to Correlative Measurements

In the Spring 2001 phase of the Asian Pacific Regional Aerosol Characterization Experiment (ACE-Asia), the 6-channel NASA Ames Airborne Tracking Sunphotometer (AATS-6) operated on 15 of the 19 research flights of the NCAR C-130, while its 14-channel counterpart (AATS-14) flew successfully on all 19 research flights of the CIRPAS Twin Otter. ACE-Asia studied aerosol outflow from the Asian continent to the Pacific basin. It was designed to integrate suborbital and satellite measurements and models to reduce the uncertainty in calculations of the climate forcing due to aerosols. AATS-6 and AATS-14 measured solar beam transmission at six and 14 wavelengths (380-1021 and 354-1558 nm, respectively), yielding aerosol optical depth (AOD) spectra and columnar water vapor (CWV). Vertical differentiation in profiles yielded aerosol extinction spectra and water vapor concentration. In this paper, we plan to present examples of the following, preliminary findings that are based in part on our airborne sunphotometer measurements: (1) The wavelength dependence of sunphotometer-derived AOD and extinction indicates that supermicron dust was often a major component of the aerosol, frequently extending to high altitudes. The percentage of full-column AOD (525 nm) that Jay above 3 km was typically 34+/-13%. In contrast, the analogous percentage of columnar water vapor was only 10+/-4%; (2) Initial comparison studies between AOD data obtained by AATS-6 and AATS-14 during coordinated low-level flight legs show agreement well within the instruments' error bars; (3) Aerosol extinction has been derived from airborne in situ measurements of scattering (nephelometers) and absorption (particle soot/ absorption photometer, PSAP) or calculated from particle size distribution measurements (mobility analyzers and aerodynamic particle sizers). Comparison with corresponding extinction values derived from the Ames airborne sunphotometer measurements shows good agreement for the vertical distribution of aerosol layers. However, the level of agreement in absolute magnitude of the derived aerosol extinction/optical depth varied among the aerosol layers sampled; (4) Initial comparisons of sunphotometer and satellite-derived AOD using SeaWiFS, MISR and AVHRR show promising results. We also plan to include comparisons with MODIS and TOMS: (5) Initial comparisons of sunphotometer-derived AOD and aerosol extinction profiles with lidars in Tokyo and on a ship show reasonable agreement.

Schmid, B.↗

NASA NTRS1986

The accuracy of Nimbus 7 LIMS temperatures in the mesosphere

Zonal-mean temperatures from the Nimbus 7 Limb Infrared Monitor of the Stratosphere (LIMS) experiment are compared with a temperature 'climatology' derived from 4 years of Rayleigh backscatter lidar measurements at 44 N and for the months of March, April, and May, when wave activity and thus atmospheric variability is very weak. The mean difference between the two data sets is less than 3.5 K between 37 and 64 km and is consistent with the theoretical estimates of accuracy reported for the LIMS data. The effects of longitudinal and year-to-year variaiations in this comparison were considered, but they do not change the conclusions significantly. These validation results extend the altitude range of accurate LIMS temperatures in the mesosphere some 10 km higher than previously reported. It also means the LIMS ozone and NO2 retrievals in the lower mesosphere should be free of any major temperature bias error effects.

Remsberg, E. E.↗

NASA NTRS2008

Linear FMCW Laser Radar for Precision Range and Vector Velocity Measurements

An all fiber linear frequency modulated continuous wave (FMCW) coherent laser radar system is under development with a goal to aide NASA s new Space Exploration initiative for manned and robotic missions to the Moon and Mars. By employing a combination of optical heterodyne and linear frequency modulation techniques and utilizing state-of-the-art fiber optic technologies, highly efficient, compact and reliable laser radar suitable for operation in a space environment is being developed. Linear FMCW lidar has the capability of high-resolution range measurements, and when configured into a multi-channel receiver system it has the capability of obtaining high precision horizontal and vertical velocity measurements. Precision range and vector velocity data are beneficial to navigating planetary landing pods to the preselected site and achieving autonomous, safe soft-landing. The all-fiber coherent laser radar has several important advantages over more conventional pulsed laser altimeters or range finders. One of the advantages of the coherent laser radar is its ability to measure directly the platform velocity by extracting the Doppler shift generated from the motion, as opposed to time of flight range finders where terrain features such as hills, cliffs, or slopes add error to the velocity measurement. Doppler measurements are about two orders of magnitude more accurate than the velocity estimates obtained by pulsed laser altimeters. In addition, most of the components of the device are efficient and reliable commercial off-the-shelf fiber optic telecommunication components. This paper discusses the design and performance of a second-generation brassboard system under development at NASA Langley Research Center as part of the Autonomous Landing and Hazard Avoidance (ALHAT) project.

Pierrottet, Diego↗

NASA NTRS1973

Use of Polarization Lidar for Investigation of Meteorological Formations

This paper presents the results of theoretical and experimental, investigations of depolarization characteristics of different meteorological formations. Experimental investigations are carried out with a monostatic lidar. The ruby laser radiation is polarized in a vertical plane. The radiation reflected is accepted by a lens system of 150 rom in diameter and a viewing angle of 12' and further it is divided by Wollaston prism into the components polarized orthogonally. In this case the principal plane of the prism is exposed parallel with the laser polarization plane. Investigations show the degree of radiation polarization, reflected from water clouds, to be changed within 1/0.7 (seldom up to 0.6) depending on their density. In most cases a signal reflected from the cloud leading edge is polarized completely. The time shift is observed between polarized and crosspolarized components of a Fignal, reflected from a cloud, depending on the density of a meteorological object. While penetrating into the cloud depth a degree of polarization decreases up to 0.8-0.7, and the character of this decrease is different for various types of clouds. For crystal clouds the shift between the components of the reflected signal is not observed and the magnitude of polarization degree amounts to 0.1/0.3 in comparison with water clouds. The polarization degree of radiation reflected by fog is not less than 0.6, and that in the rains of average intensity (about 5 mm/h) is always about 1. The authors have suggested an algorithm of numerical solution of nonstationary transfer equation in the vector form to forecast the influence of multiple scattering effects on polarization characteristics of the lidar light signal. The method of statistical simulation (Monte-Carlo technique) forms the basis of the algorithm. Numerical estimates obtained for a model of stratocumulus at lambda = 0.6943 microns under boundary conditions close to the conditions of natural experiment being discussed proved to be in a good agreement with the results of observation. Specifically, Fig. 1 shows the profiles of polarization (p) versus depth (L) of the following drop formations: fog (curve 1) with horizontal meteorological visibility of 4 km two stratocumulus at a height of 1100 m with the attenuation factors delta = 0.01m(exp -1) (curve 2) and delta = 0.05m(exp -1) (curve 3). Curve 3 shows the results of numerical estimates and the value of their statistical error.

Balin, Yu. S.↗

NASA NTRS2001

The impact of Doppler lidar wind observations on a single-level meteorological analysis

Through the use of observation operators, modern data assimilation systems have the capability to ingest observations of quantities that are not themselves model variables, but are mathematically related to those variables. An example of this are the so-called LOS (line of sight) winds that a Doppler wind Lidar can provide. The model - or data assimilation system - needs information about both components of the horizontal wind vectors, whereas the observations in this case only provide the projection of the wind vector onto a given direction. The analyzed value is then calculated essentially based on a comparison between the observation itself and the model-simulated value of the observed quantity. However, in order to assess the expected impact of such an observing system, it is important to examine the extent to which a meteorological analysis can be constrained by the LOS winds. The answer to this question depends on the fundamental character of the atmospheric flow fields that are analyzed, but more importantly it also depends on the real and assumed error covariance characteristics of these fields. A single-level wind analysis system designed to explore these issues has been built at the NASA Data Assimilation Office. In this system, simulated wind observations can be evaluated in terms of their impact on the analysis quality under various assumptions about their spatial distribution and error characteristics and about the error covariance of the background fields. The basic design of the system will be presented along with experimental results obtained with it. In particular, the value of simultaneously measuring LOS winds along two different directions for a given location will be discussed.

Riishojgaard, L. P.↗

NASA NTRS2015

Swarm Flyby Gravimetry

This study describes a new technology for discerning the gravity fields and mass distribution of a solar system small body, without requiring dedicated orbiters or landers. Instead of a lander, a spacecraft releases a collection of small, simple probes during a flyby past an asteroid or comet. By tracking those probes from the host spacecraft, one can estimate the asteroid's gravity field and infer its underlying composition and structure. This approach offers a diverse measurement set,equivalent to planning and executing many independent and unique flyby encounters of a single spacecraft. This report assesses a feasible hardware implementation, derives the underlying models,and analyzes the performance of this concept via simulation.In terms of hardware, a small, low mass, low cost implementation is presented, which consists of a dispenser and probes. The dispenser contains roughly 12 probes in a tube and has a total size commensurate with a 6U P-Pod. The probes are housed in disc shaped sabots. When commanded,the dispenser ejects the top-most probe using a linear motor. The ejected probe separates from its sabots and unfolds using internal springs. There are two types of probes, each designed for a particular tracking modality. The reflective probe type, tracked by a telescope, unfolds to forma diffusely reflective sphere. The retroreflector probe type, tracked by a lidar, unfolds to form a corner-cube retroreflector assembly. Both types are designed to spherical so that their attitude doesn't affect the spacecraft's tracking performance.This analysis indicates that the point-mass term of small bodies larger than roughly 500 m in diameter can be observed from a host spacecraft that tracks locally deployed probes throughout a flyby to an uncertainty of better than 5%. The conditions by which this measurement is possible depends on the characteristics of the asteroid (size, type), the flyby velocity, and the type of tracking available (angles-only or angles+ranging). For most encounters, a few (1-3) well placed probes can be very effective, with marginal improvement for additional probes. Given realistic deployment errors, an encounter may require roughly 10-12 probes to ensure that 1-3 achieve their target. Long duration tracking of probes flying by large asteroids (>5 km diameter) can sometimes provide observability of the gravity field's first spherical harmonic, J( sub 2). In summary, this method offers a feasible, affordable approach to enabling or augmenting flyby science.

Atchison, Justin↗

NASA NTRS2020

Biomass Estimation from Simulated GEDI, ICESat-2 and NISAR Across Environmental Gradients in Sonoma County, California

Estimates of the magnitude and distribution of aboveground carbon in Earth’s forests remain uncertain, yet knowledge of forest carbon content at a global scale is critical for forest management in support of climate mitigation. In light of this knowledge gap, several upcoming spaceborne missions aim to map forest aboveground biomass, and many new biomass products are expected from these datasets. As these new missions host different technologies, each with relative strengths and weaknesses for biomass retrieval, as well as different spatial resolutions, consistently comparing or combining biomass estimates from these new datasets will be challenging. This paper presents a demonstration of an inter-comparison of biomass estimates from simulations of three NASA missions (GEDI, ICESat-2 and NISAR) over Sonoma county in California, USA. We use a high resolution, locally calibrated airborne lidar map as our reference dataset, and emphasize the importance of considering uncertainties in both reference maps and spaceborne estimates when conducting biomass product validation. GEDI and ICESat-2 were simulated from airborne lidar point clouds, while UAVSAR’s L-band backscatter was used as a proxy for NISAR. To estimate biomass for the lidar missions we used GEDI’s footprint-level biomass algorithms, and also adapted these for application to ICESat-2. For UAVSAR, we developed a locally trained biomass model, calibrated against the ALS reference map. Each mission simulation was evaluated in comparison to the local reference map at its native product resolution (25 m, 100m transect, and 1 ha) yielding RMSEs of 57%, 75%, and 89% for GEDI, NISAR, and ICESat-2 respectively. RMSE values increased for GEDI’s power beam during simulated daytime conditions (64%), coverage beam during nighttime conditions (72%), and coverage beam daytime conditions (87%). We also test the application of GEDI’s biomass modeling framework for estimation of biomass from ICESat-2, and fine that ICESat-2 yields reasonable biomass estimates, particularly in relatively short, open canopies. Results suggest that while all three missions will produce datasets useful for biomass mapping, tall, dense canopies such as those found in Sonoma County present the greatest challenges for all three missions, while steep slopes also prove challenging for single-date SAR based biomass retrieval. Our methods provide guidance for the inter-comparison and validation of spaceborne biomass estimates through the use of airborne lidar reference maps, and could be repeated with on-orbit estimates in any area with high quality field plot and ALS data. These methods allow for regional interpretations and filtering of multi-mission biomass estimates toward improved wall-to-wall biomass maps through data fusion.

GEDI↗

NASA NTRS1992

Efficiencies of Rotational Raman, and Rayleigh Techniques for Laser Remote Sensing of the Atmospheric Temperature

Various lidar methods have been developed for measuring the atmospheric temperature, making use of the temperature dependant characteristics of rotational Raman scattering (RRS) from nitrogen and oxygen, and Rayleigh or Rayleigh-Brillowin scattering (RS or RBS). These methods have various advantages and disadvantages as compared to each other but their potential accuracies are principal characteristics of their efficiency. No systematic attempt has been undertaken so far to compare the efficiences, in the above meaning, of different temperature lidar methods. Two RRS techniques have been compared. Here, we do such a comparison using two methods based on the detection and analysis of RS (RBS) spectra. Four methods are considered here for measuring the atmospheric temperature. One of them (Schwiesow and Lading, 1981) is based on an analysis of the RS linewidth with two Michelson interferometers (MI) in parallel. The second method (Shimisu et al., 1986) employs a high-resolution analysis of the RBS line shape. The third method (Cooney, 1972) employs the temperature dependance of the RRS spectrum envelope. The fourth method (Armstrong, 1974) makes use of a scanning Fabry-Perot interferometer (FPI) as a comb filter for processing the periodic RRS spectrum of the nitrogen. Let us denote the corresponding errors in measuring the temperature by sigma(sub MI), sigma(sub HR), sigma(sub ENV), and sigma(sub FPI). Let us also define the ratios chi(sub 1) = sigma(sub MI)/sigma(sub ENV), chi(sub 2) = sigma(sub HR)/sigma(sub ENV), and chi(sub 3) = sigma(sub FPI)/sigma(sub ENV) interpreted as relative errors with respect to sigma(sub ENV).

Ivanova, I. D.↗

NASA NTRS2012

Integrated Path Differential Absorption Lidar Optimizations Based on Pre-Analyzed Atmospheric Data for ASCENDS Mission Applications

In this paper a modeling method based on data reductions is investigated which includes pre analyzed MERRA atmospheric fields for quantitative estimates of uncertainties introduced in the integrated path differential absorption methods for the sensing of various molecules including CO2. This approach represents the extension of our existing lidar modeling framework previously developed and allows effective on- and offline wavelength optimizations and weighting function analysis to minimize the interference effects such as those due to temperature sensitivity and water vapor absorption. The new simulation methodology is different from the previous implementation in that it allows analysis of atmospheric effects over annual spans and the entire Earth coverage which was achieved due to the data reduction methods employed. The effectiveness of the proposed simulation approach is demonstrated with application to the mixing ratio retrievals for the future ASCENDS mission. Independent analysis of multiple accuracy limiting factors including the temperature, water vapor interferences, and selected system parameters is further used to identify favorable spectral regions as well as wavelength combinations facilitating the reduction in total errors in the retrieved XCO2 values.

Pliutau, Denis↗

NASA NTRS1998

Ice Surface Elevation Changes in East Antarctica from Satellite Altimetry

Estimates of the overall mass balance and seasonal and inter-annual variations in the surface mass balance are obtainable from time-series of ice surface elevations measured by satellite altimetry. Beginning in 2001, NASA's ICESat laser altimeter and lidar mission will significantly improve the range accuracy, the orbit accuracy, and the spatial coverage for measurement of ice sheet elevations (to 86 S) , as compared to previous radar altimeters designed for ocean measurements The radar altimeters on Seasat and Geosat provided ice sheet measurements to 72 S, and on ERS-1 and ERS-2 to 81 S. Although radar altimetry has significant limitations in coverage (due to loss of tracking) and accuracy over sloping surfaces, information on ice-sheet surface-elevation changes has been derived for parts of Antarctica. Recently, the accuracy of the ice measurements by Seasat (3 months of 1978) and Geosat (1985 to 1989) have been improved by new calculations of the satellite orbit heights and other altimeter corrections. Residual orbit errors and inter-satellite biases are evaluated by crossover analysis and by global adjustments to an ocean surface derived from altimeter data. The standard deviation of the orbit error is less than 9 cm, and the long-term trend in the error appears to be less than 1 cm/yr. Orbit errors can be further reduced by adjustment to the ocean surface, but false signals of several cm/yr may be also introduced by the adjustments. These false signals are caused mainly by residual errors in the altimeter corrections over the ocean, and secondary by real changes in the ocean surface elevation. Maps of ice sheet elevation changes north of 72 S are derived from Seasat-Geosat crossovers and from 4.5 years of Geosat crossovers. A notable ice thinning rate of about 50 cm/yr is found at elevations below 2200 meters between 70 and 72 S to the East of the Amery ice shelf, in both the Seasat-Geosat and Geosat-Geosat time intervals Above 2200 meters, to the ridge around 95 E, the thinning is about 10 to 20 cm/yr. For the Seasat/Geosat interval, a thickening is noted on the area East of the ridge between about 95 E and 115 E. Preliminary results from analysis of ERS-1 and ERS-2 radar altimeter data are also described.

Zwally, H. Jay↗

NASA NTRS2016

Wavelength Locking to CO2 Absorption Line-Center for 2-Micron Pulsed IPDA Lidar Application

An airborne 2-micron triple-pulse integrated path differential absorption (IPDA) lidar is currently under development at NASA Langley Research Center (LaRC). This IPDA lidar system targets both atmospheric carbon dioxide (CO2) and water vapor (H2O) column measurements. Independent wavelength control of each of the transmitted laser pulses is a key feature for the success of this instrument. The wavelength control unit provides switching, tuning and locking for each pulse in reference to a 2-micron CW (Continuous Wave) laser source locked to CO2 line-center. Targeting the CO2 R30 line center, at 2050.967 nanometers, a wavelength locking unit has been integrated using semiconductor laser diode. The CO2 center-line locking unit includes a laser diode current driver, temperature controller, center-line locking controller and CO2 absorption cell. This paper presents the CO2 center-line locking unit architecture, characterization procedure and results. Assessment of wavelength jitter on the IPDA measurement error will also be addressed by comparison to the system design.

Refaat, Tamer F.↗

NASA NTRS2018

NASA SPLICE Project: Development and Testing of Precision Landing GN&C Technologies

NASA's technology advancement needs for entry, descent and landing call for high-precision, high-rate sensors that can improve navigation accuracy and vehicle control performance. Higher landing accuracy is required for any future human lander missions, and likely, for most robotic missions 1,2. Sensors and algorithms that significantly reduce navigation errors and can image the local terrain will enable landing at locations of high scientific interest that would otherwise pose significant risk to the vehicle. The Safe and Precise Landing-Integrated Capabilities Evolution project, or SPLICE, is developing precision landing and hazard avoidance (PL&HA) technologies for NASA and for potential commercial space flight missions. SPLICE technologies include sensors, algorithms, advanced space flight computing capabilities, and simulation tools used to integrate and study guidance, navigation, and control (GN&C) system performance. SPLICE efforts include hardware-in-the-loop (HWIL) simulation testing, ground testing, and flight testing, including reuse of hardware from the CoOperative Blending of Autonomous Landing Technologies (COBALT) suborbital flight-test payload3,4. Two of the precise navigation sensors that are being developed and matured within SPLICE are LiDARs. Since 2006, NASA Langley has been developing a Navigation Doppler LiDAR (NDL) for precise velocity measurements, and SPLICE is building an NDL engineering test unit (ETU) that will be brought up to TRL 6 following environmental and high-speed1,2 testing. NASA Goddard is developing a Hazard Detection LiDAR (HD LiDAR) engineering development unit (EDU) for SPLICE that has relevance to future human and robotic lander missions. The HD LiDAR will be flight test and matured to TRL 5.

Restrepo, Carolina I.↗