SEARCH · Search NASA

Results for “material parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1990

The effect of suspended particles on Jean's criterion for gravitational instability

The effect that the proper inclusion of suspended particles has on Jeans' criterion for the self-gravitational instability of an unbounded nonrotating adiabatic gas cloud is examined by formulating the appropriate model system, introducing particular physically plausible equations of state and constitutive relations, performing a linear stability analysis of a uniformly expanding exact solution to these governing equations, and exploiting the fact that there exists a natural small material parameter for this problem given by N sub 1/n sub 1, the ratio of the initial number density for the particles to that for the gas. The main result of this investigation is the derivation of an altered criterion which can substantially reduce Jeans' original critical wavelength for instability. It is then shown that the existing discrepancy between Jeans' theoretical prediction using and actual observational data relevant to the Andromeda nebula M31 can be accounted for by this new criterion of assuming suspended particles of a reasonable grain size and distribution to be present.

Wollkind, David J.↗

NASA NTRS1991

A theoretical comparison of the near-optimum design and predicted performance of n/p and p/n indium phosphide homojunction solar cells

Using a detailed simulation model of p(+)nn(+) and n(+)pp(+) indium phosphide (InP) homojunction solar cells, extensive parametric variation computer simulation runs were performed to aid in making near-optimum designs for these two solar cell configurations. The values of all the geometrical and material parameters corresponding to the near-optimal designs of both these configurations are presented. The results of parametric variation runs are presented for each configuration showing how the performance parameters J(sub sc), V(sub oc), and eta vary with each of the cell design parameters for the near-optimally designed cell. Finally, the theoretically obtained results are discussed, and the relative merits and drawbacks of the two configurations are compared.

Goradia, Chandra↗

NASA NTRS1990

The effect of an electric field on the morphological stability of the crystal-melt interface of a binary alloy. III - Weakly nonlinear theory

The effect of a constant electric current on the crystal-melt interface morphology during directional solidification at constant velocity of a binary alloy is considered. A linear temperature field is assumed, and thermoelectric effects and Joule heating are neglected; electromigration and differing electrical conductivities of crystal and melt are taken into account. A two-dimensional weakly nonlinear analysis is carried out to third order in the interface amplitude, resulting in a cubic amplitude equation that describes whether the bifurcation from the planar state is supercritical or subcritical. For wavelengths corresponding to the most dangerous mode of linear theory, the demarcation between supercritical and subcritical behavior is calculated as a function of processing conditions and material parameters. The bifurcation behavior is a sensitive function of the magnitude and direction of the electric current and of the electrical conductivity ratio.

Wheeler, A. A.↗

NASA NTRS1991

Tunnel transit-time (TUNNETT) devices for terahertz sources

The potential and capabilities of tunnel transit-time (TUNNETT) devices for power generation in the 100-1000 GHz range are presented. The basic properties of these devices and the important material parameters which determine their properties are discussed and criteria for designing such devices are presented. It is shown from a first-order model that significant amounts of power can be obtained from these devices in the terahertz frequency range.

Haddad, G. I.↗

NASA NTRS1990

Regolith-structure modeling of lunar facilities

The mechanical properties of lunar regolith are significantly different from terrestrial soils; at low stress levels, the ultimate strength envelope is highly nonlinear, and the material is essentially dilatant. The effects of platen friction, membrane confinement, and material self weight in triaxial tests have been shown to be of great significance in low stress level tests. An inverse identification technique has been devised to account for these effects where the load-displacement response of the entire specimen, including the boundary conditions and the self-weight, was analyzed by nonlinear finite element techniques so as to obtain true material parameters.

Perkins, Steven W.↗

NASA NTRS1991

Concurrent material-fabrication optimization of metal-matrix laminates under thermo-mechanical loading

A methodology is developed to tailor fabrication and material parameters of metal-matrix laminates for maximum loading capacity under thermomechanical loads. The stresses during the thermomechanical response are minimized subject to failure constrains and bounds on the laminate properties. The thermomechanical response of the laminate is simulated using nonlinear composite mechanics. Evaluations of the method on a graphite/copper symmetric cross-ply laminate were performed. The cross-ply laminate required different optimum fabrication procedures than a unidirectional composite. Also, the consideration of the thermomechanical cycle had a significant effect on the predicted optimal process.

Saravanos, D. A.↗

NASA NTRS1990

Structural and optical properties for typical solid mirror shapes

A method is developed to determine the weight, center of gravity, areal properties, and mass inertial properties for typical mirrors. A number of support conditions were considered to examine optical surface deflections, surface quality, and fundamental natural frequency for single- and double-arch mirror shapes. Structural performance estimates were made with the NASTRAN program, and optical performances were evaluated with the FRINGE program, using an SXA 40-in mirror. To show the behavior of element types from the NASTRAN program, finite element validity and sensitivity studies were performed in optical model applications. Material parameters, contoured back shapes, and support locations are shown to have significant effects on structural and optical performances. Optimal support locations and support points are given. Fundamental natural frequencies for some shapes are found with the closed-form solution. The plate models results may not be acceptable for determining real mirror optical performances.

Cho, Myung K.↗

NASA NTRS1990

Photovoltaic characteristics of n(+)pp(+) InP solar cells grown by OMVPE

The photovoltaic characteristics of n(+)/p/p(+) homojunction InP solar cells fabricated by organometallic vapor-phase epitaxy (OMVPE) are described. The cells are characterized by I-V, C-V and quantum efficiency measurements, and simulations are used to obtain various device and material parameters. The I-V characteristics show a high recombination rate in the depletion region; this is shown to be independent of the impurity used. It is shown that cadmium is easier to use as an acceptor for the p base and p(+) buffer and is therefore beneficial. The high quantum efficiency of 98 percent at long wavelengths measured in these cells indicates a very good collection efficiency in the base. The short-wavelength quantum efficiency is poor, indicating a high surface recombination.

Tyagi, S.↗

NASA NTRS1991

Reflective overcoats for radiation control surfaces

Theoretical models are developed to predict the surface properties of a coating layer composed of particles of a known size distribution, applied to an opaque substrate, such as a metal or reaction cured glass (RCG). The surface temperature attained at radiative equilibrium by an overcoated surface subject to a given heat flux is calculated. The incident radiation was assumed to exhibit the spectral distribution characteristic of a black body at different temperatures or equivalently, having different peak wavelengths, with the energy level scaled to give a range of desired surface radiative heat fluxes. This approach allows a straightforward comparison of the thernal response of a surface to incident radiation having the energy predominantly in a characteristic wavelength band and a well-defined spectral distribution. The ratio of the radiative heat flux to the total heat flux was varied, and the different geometric and material parameters of such overcoat layers were explored. The model was applied to representative surface heating rates to the Aeroasssisted Flight Experiment (AFE) and to Aeroassisted Space Transfer Vehicles (ASTVs). The predicted radiative energy flux to the surface of the AFE vehicle gives a single-point comparison of the surface temperatures attained with and without a selective-reflector overcoat on the vehicle surface. The specific objective of this work is to identify the most desirable radiative properties of an overcoat/substrate system for this environment.

White, Susan M.↗

NASA NTRS1991

Thermal postbuckling of thin-walled composite stiffeners

A study is made of the thermal postbuckling response of composite stiffeners subjected to prescribed edge displacement and a temperature rise. The flanges and web of the stiffeners are modeled by using two-dimensional plate finite elements. A mixed formulation is used with the fundamental unknowns consisting of the generalized displacements and the stress resultants of the plate. A reduction method is used in conjunction with mixed finite element models for determining the postbuckling response of the stiffeners. Sensitivity derivatives are evaluated and used to study the effects of variations in the different lamination and material parameters of the stiffeners on their postbuckling response characteristics. Numerical studies are presented for anisotropic stiffeners with Zee and channel sections.

Noor, Ahmed K.↗

NASA NTRS1991

An adjustable RF tuning element for microwave, millimeter wave, and submillimeter wave integrated circuits

Planar RF circuits are used in a wide range of applications from 1 GHz to 300 GHz, including radar, communications, commercial RF test instruments, and remote sensing radiometers. These circuits, however, provide only fixed tuning elements. This lack of adjustability puts severe demands on circuit design procedures and materials parameters. We have developed a novel tuning element which can be incorporated into the design of a planar circuit in order to allow active, post-fabrication tuning by varying the electrical length of a coplanar strip transmission line. It consists of a series of thin plates which can slide in unison along the transmission line, and the size and spacing of the plates are designed to provide a large reflection of RF power over a useful frequency bandwidth. Tests of this structure at 1 GHz to 3 Ghz showed that it produced a reflection coefficient greater than 0.90 over a 20 percent bandwidth. A 2 GHz circuit incorporating this tuning element was also tested to demonstrate practical tuning ranges. This structure can be fabricated for frequencies as high as 1000 GHz using existing micromachining techniques. Many commercial applications can benefit from this micromechanical RF tuning element, as it will aid in extending microwave integrated circuit technology into the high millimeter wave and submillimeter wave bands by easing constraints on circuit technology.

Lubecke, Victor M.↗

NASA NTRS1990

Materials characterization using acoustic nonlinearity parameters and harmonic generation - Engineering materials

The paper reviews nonlinear bulk compressional wave acoustic measurement systems and the applications of measurements from such systems to engineering materials. Preliminary measurements indicate that it is possible to determine percent second phase precipitates in aluminum alloys, while other measurements show promise in the determination of properties related to the fatigue states of metals. It is also shown that harmonic generation can be used for the study of crack opening loads in compact tension specimens, which in turn gives useful information about the fatigue properties of various engineering materials.

Yost, William T.↗

NASA NTRS1992

Accuracy of critical-temperature sensitivity coefficients predicted by multilayered composite plate theories

An assessment is made of the accuracy of the critical-temperature sensitivity coefficients of multilayered plates predicted by different modeling approaches, based on two-dimensional shear-deformation theories. The sensitivity coefficients considered measure the sensitivity of the critical temperatures to variations in different lamination and material parameters of the plate. The standard of comparison is taken to be the sensitivity coefficients obtained by the three-dimensional theory of thermoelasticity. Numerical studies are presented showing the effects of variation in the geometric and lamination parameters of the plate on the accuracy of both the sensitivity coefficients and the critical temperatures predicted by the different modeling approaches.

Noor, Ahmed K.↗

NASA NTRS1991

Theoretical modeling, near-optimum design and predicted performance of n(+)pp(+) and p(+)nn(+) indium phosphide homojunction solar cells

Using a detailed simulation model of p(+)nn(+) and n(+)pp(+) indium phosphide (InP) homojunction solar cells, extensive parametric variation computer simulation runs are conducted to help arrive at near-optimum designs of these two solar cell configurations. Values of all the geometrical and material parameters corresponding to the near-optimal designs of both these configurations are presented. For each configuration, results are given for parametric variation runs showing how the performance parameters JSC, VOC, and eta vary with each of the cell parameters for the near-optimally designed cell.

Goradia, Chandra↗

NASA NTRS1992

Superplastic forming of ceramic insulation

Superplasticity has been demonstrated in many fine-grained structural ceramics and ceramic composites, including yttria-stabilized tetragonal zirconia polycrystal (YTZP), alumina, and Al2O3-reinforced zirconia (Al2O3/YTZ) duplex composites and SiC-reinforced Si3N4. These superplastic ceramics obviously offer the potential benefit of forming net shape or near net shape parts. This could be particularly useful for forming complicated shapes that are difficult to achieve using conventional forming techniques, or require elaborate, subsequent machining. In the present study, we successfully demonstrated the following: (1) superplastic 3Y-TXP and 20 percent Al2O3/YTZ composite have for the first time been successfully deformed into hemispherical caps via a biaxial gas-pressure forming technique; (2) no experimental difficulty was encountered in applying the required gas pressures and temperatures to achieve the results, thus, it is certain that higher rates of deformation than those presented in this study will be possible by using the current test apparatus at higher temperatures and pressures; and (3) an analytical model incorporating material parameters, such as variations during forming in the strain rate sensitivity exponent and grain growth-induced strain hardening, is needed to model accurately and therefore precisely control the biaxial gas-pressure forming of superplastic ceramics. Based on the results of this study, we propose to fabricate zirconia insulation tubes by superplastic extrusion of zirconia polycrystal. This would not only reduce the cost, but also improve the reliability of the tube products.

Nieh, T. G.↗

NASA NTRS1993

Optimal design of composite hip implants using NASA technology

Using an adaptation of NASA software, we have investigated the use of numerical optimization techniques for the shape and material optimization of fiber composite hip implants. The original NASA inhouse codes, were originally developed for the optimization of aerospace structures. The adapted code, which was called OPORIM, couples numerical optimization algorithms with finite element analysis and composite laminate theory to perform design optimization using both shape and material design variables. The external and internal geometry of the implant and the surrounding bone is described with quintic spline curves. This geometric representation is then used to create an equivalent 2-D finite element model of the structure. Using laminate theory and the 3-D geometric information, equivalent stiffnesses are generated for each element of the 2-D finite element model, so that the 3-D stiffness of the structure can be approximated. The geometric information to construct the model of the femur was obtained from a CT scan. A variety of test cases were examined, incorporating several implant constructions and design variable sets. Typically the code was able to produce optimized shape and/or material parameters which substantially reduced stress concentrations in the bone adjacent of the implant. The results indicate that this technology can provide meaningful insight into the design of fiber composite hip implants.

Blake, T. A.↗

NASA NTRS1992

Transit-time devices as local oscillators for frequencies above 100 GHz

Very promising preliminary experimental results have been obtained from GaAs IMPATT diodes at F-band frequencies (75 mW, 3.5 percent at 111.1 GHz and 20 mW, 1.4 percent at 120.6 GHz) and from GaAs TUNNETT diodes at W-band frequencies (26 mW, 1.6 percent at 87.2 GHz and 32 mW, 2.6 percent at 93.5 GHz). These results indicate that IMPATT, MITATT and TUNNETT diodes have the highest potential of delivering significant amounts of power at Terahertz frequencies. As shown recently, the noise performance of GaAs W-band IMPATT diodes can compete with that of Gunn devices. Since TUNNETT diodes take advantage of the quieter tunnel injection, they are expected to be especially suited for low-noise local oscillators. This paper will focus on the two different design principles for IMPATT and TUNNETT diodes, the material parameters involved in the design and some aspects of the present device technology. Single-drift flat-profile GaAs D-band IMPATT diodes had oscillations up to 129 GHz with 9 mW, 0.9 percent at 128.4 GHz. Single-drift GaAs TUNNETT diodes had oscillations up to 112.5 GHz with 16 mW and output power levels up to 33 mW and efficiencies up to 3.4 percent around 102 GHz. These results are the best reported so far from GaAs IMPATT and TUNNETT diodes.

Eisele, H.↗

NASA NTRS1992

Modeling, design, fabrication, and testing of InP Gunn devices in the D-band (110 GHz - 170 GHz)

The development of fundamental Gunn sources for D-band frequencies requires improvements of doping profiles, processing technology, and circuit design. We have developed a technology for fabricating InP Gunn diodes using an InGaAs etch-stop layer between the InP substrate and the device layers. The epitaxial layers were grown by CBE. During device processing, the substrate is completely removed. Substrateless devices with an n(+) InGaAs cap layer are expected to have reduced contact and series resistances, and skin effect losses. This technology gives better uniformity and control of the device geometry across the processed chip. InP Gunn devices with a 1.7 micron long active region (doping : 9 x 10(exp 15) cm(exp -3)) have been mounted on copper heat sinks. Two tapered leads were then bonded to the diode and to four quartz standoffs. As a preliminary result, an output power of 13 mW at 82 GHz was obtained. Based on these RF measurements, we determine appropriate material parameters to be used in the Ensemble Monte Carlo model. Subsequently, we use this model to design and evaluate the performance of InP Gunn Devices for D-band frequencies. Using the same technology, we are currently processing Gunn devices with a 1 micron long active region for operation at higher frequencies.

Kamoua, R.↗