Search NASA⌕ Search

SEARCH · Search NASA

Results for “patterned beam”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

An approach to tune the amplitude of surface ripple patterns

An approach is presented to tune the amplitude of ripple patterns using ion beam. By varying the depth location of amorphous/crystalline interface, ripple patterns of different amplitude with similar wavelength were grown on the surface of Si (100) using 50 keV Ar{sup +} beam irradiation. Atomic force microscopy study demonstrates the tuning of amplitude of ripples patterns for wide range. Rutherford backscattering channeling measurement was performed to measure the depth location of amorphous/crystalline interface. It is postulated that the ion beam stimulated solid flow inside the amorphous layer controls the wavelength, whereas mass rearrangement at amorphous/crystalline interface controls the amplitude.

36 MATERIALS SCIENCE↗

Oxygen vacancy mediated enhanced photo-absorption from ZnO(0001) nanostructures fabricated by atom beam sputtering

The nanoscale patterns created on the ZnO(0001) surfaces during atom beam irradiation have been investigated here for their photo absorption response. Preferential sputtering, during irradiation, promotes Zn-rich zones that serve as the nucleation centers for the spontaneous creation of nanostructures. Nanostructured surfaces with bigger (78 nm) nanodots, displaying hexagonal ordering and long ranged periodic behavior, show higher photo absorption and a ∼0.09 eV reduced bandgap. These nanostructures also demonstrate higher concentration of oxygen vacancies which are crucial for these results. The enhanced photo-response, as observed here, has been achieved in the absence of any dopant elements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SU-D-304-05: Validation of Low-Dose-Tail Modeling for Proton Pencil Beam Spot Scanning Using a Quality Assurance Test Pattern

Purpose: The purpose of this manuscript is to demonstrate the utility of a comprehensive test pattern in validating calculation models of the low-dose tails of proton pencil beam scanning (PBS) spots. Such a pattern has been used previously for quality assurance purposes to assess spot shape and location, and for determining monitor units. Methods: In this study, a scintillation detector was used to measure the test pattern in air at isocenter for two proton beam energies (115 and 225 MeV) of two IBA universal nozzles (UN). Planar measurements were compared with calculated dose distribution based on the weighted superposition of spot profiles previously measured using a pair-magnification method. Results: Including the halo component below 1% of the central dose is shown to improve the gamma-map comparison between calculation and measurement from 94.9% to 98.4% using 2 mm/2% criteria for the 115 MeV proton beam of UN #1. In contrast, including the halo component below 1% of the central dose does not improve the gamma agreement for the 115 MeV proton beam of UN #2, due to the cutoff of the halo component at off-axis locations. When location-dependent spot profiles are used for calculation instead of spot profiles at central axis, the gamma agreement is improved from 98.0% to 99.5% using 2 mm/2% criteria. The cutoff of the halo component is smaller at higher energies, and is not observable for the 225 MeV proton beam for UN #2. Conclusion: In conclusion, the use of a comprehensive test pattern can facilitate the validation of the halo component of proton PBS spots at off axis locations. The cutoff of the halo component should be taken into consideration for large fields or PBS systems that intend to trim spot profiles using apertures. This work was supported by the US Army Medical Research and Materiel Command under Contract Agreement No. DAMD17-W81XWH-07-2-0121 and W81XWH-09-2-0174.

60 APPLIED LIFE SCIENCES↗

Gold-implanted shallow conducting layers in polymethylmethacrylate

PMMA (polymethylmethacrylate) was ion implanted with gold at very low energy and over a range of different doses using a filtered cathodic arc metal plasma system. A nanometer scale conducting layer was formed, fully buried below the polymer surface at low implantation dose, and evolving to include a gold surface layer as the dose was increased. Depth profiles of the implanted material were calculated using the Dynamic TRIM computer simulation program. The electrical conductivity of the gold-implanted PMMA was measured in situ as a function of dose. Samples formed at a number of different doses were subsequently characterized by Rutherford backscattering spectrometry, and test patterns were formed on the polymer by electron beam lithography. Lithographic patterns were imaged by atomic force microscopy and demonstrated that the contrast properties of the lithography were well maintained in the surface-modified PMMA.

36 MATERIALS SCIENCE↗

Precise, reproducible nano-domain engineering in lithium niobate crystals

We present a technique for domain engineering the surface of lithium niobate crystals with features as small as 100 nm. A film of chromium (Cr) is deposited on the lithium niobate surface and patterned using electron beam lithography and lift-off and then irradiated with a wide diameter beam of intense visible laser light. The regions patterned with chromium are domain inverted while the uncoated regions are not affected by the irradiation. With the ability to realize nanoscale surface domains, this technique could offer an avenue for fabrication of nano-photonic and phononic devices.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Effect of interwire separation on growth kinetics and properties of site-selective GaAs nanowires

We report tuning of the growth kinetics, geometry, and properties of autocatalytic GaAs nanowires (NW) by precisely controlling their density on SiO{sub 2}-mask patterned Si (111) substrates using selective area molecular beam epitaxy. Using patterned substrates with different mask opening size (40–120 nm) and pitch (0.25–3 μm), we find that the NW geometry (length, diameter) is independent of the opening size, in contrast to non-catalytic GaAs NWs, whereas the NW geometry strongly depends on pitch, i.e., interwire separation and NW density. In particular, two distinct growth regimes are identified: a diffusion-limited regime for large pitches (low NW density) and a competitive growth regime for smaller pitches (high NW density), where axial and radial NW growth rates are reduced. The transition between these two regimes is significantly influenced by the growth conditions and shifts to smaller pitches with increasing As/Ga flux ratio. Ultimately, the pitch-dependent changes in growth kinetics lead to distinctly different photoluminescence properties, highlighting that mask template design is a very critical parameter for tuning intrinsic NW properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Spatial solitons in a three-level atomic medium supported by a Laguerre-Gaussian control beam

We investigate the existence and stability of various types of spatial solitons in a three-level atomic medium with Laguerre-Gaussian control beam. Radial and azimuthal modulations of the medium properties, introduced by the control beam, provide possibilities for existence of diverse soliton patterns and dynamics. Beam diffraction provides additional soliton controllability. All types of solitons can be generated at very low input energy at a few-photon level.

43 PARTICLE ACCELERATORS↗

Spin-torsion effects in the hyperfine structure of methanol

The magnetic hyperfine structure of the non-rigid methanol molecule is investigated experimentally and theoretically. 12 hyperfine patterns are recorded using molecular beam microwave spectrometers. These patterns, along with previously recorded ones, are analyzed in an attempt to evidence the effects of the magnetic spin-torsion coupling due to the large amplitude internal rotation of the methyl group [J. E. M. Heuvel and A. Dymanus, J. Mol. Spectrosc. 47, 363 (1973)]. The theoretical approach setup to analyze the observed data accounts for this spin-torsion in addition to the familiar magnetic spin-rotation and spin-spin interactions. The theoretical approach relies on symmetry considerations to build a hyperfine coupling Hamiltonian and spin-rotation-torsion wavefunctions compatible with the Pauli exclusion principle. Although all experimental hyperfine patterns are not fully resolved, the line position analysis yields values for several parameters including one describing the spin-torsion coupling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fraunhofer diffraction of a Gaussian beam by a four-sector binary grating with a half period fringes shift between adjacent sectors

The study of Fraunhofer diffraction of a Gaussian laser beam by a computer-generated, binary four-sector grating (FSG) is presented. In the four equal angular sectors of the FSG, parts of a binary rectilinear grating are embedded in such a way that, two neighboring parts are shifted by a half spatial rectilinear grating period. Analytical expressions, describing the diffracted wave field amplitude and intensity distributions in the focal plane of a converging lens, are derived. The zeroth-diffraction-order beam is a Gaussian beam whose transverse cross section has a reduced Gaussian radius. The higher-diffraction-order beam transverse intensity profiles have four bright spots divided by dark crossed lines and a central dark, non-vortex core. They can be described as cosine-Laguerre–Gaussian Kummer beams. The numerically calculated diffraction patterns, as well as the interference patterns of the diffracted beam with a slightly inclined plane wave, are supported by experimentally obtained ones. In both investigations (theoretical and experimental) the interferograms confirm the non-vortex nature of the diffraction spots.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Calibration of a synthetic aperture radiometer

Calibration algorithms for a synthetic aperture microwave radiometer are presented. The calibration is geared to Earth remote sensing applications, and is demonstrated on an airborne prototype of thinned array imager. Two approaches to the system calibration are presented; the first utilizes commonly available reference brightness temperature scenes, such as open water, and the second utilizes data collected on the antenna range. Both algorithms yield spatial response information which is cast in matrix form and inverted to obtain the image reconstruction formula. Experimental results are examined, and errors in some reconstructed images are linked to the present prototype antenna design. Algorithms for improving the synthesized antenna pattern side lobe performance are also presented. In one solution, the pattern efficiency is optimized by minimizing the pattern outside a defined beam. In another solution, the patterns are matched to a desired model pattern by the method of least squared errors. Both techniques offer an attractive alternative to aperture weighting.

Tanner, Alan B.↗

Technical Note: Validation of halo modeling for proton pencil beam spot scanning using a quality assurance test pattern

Purpose: The purpose of this paper is to demonstrate the utility of a comprehensive test pattern in validating calculation models that include the halo component (low-dose tails) of proton pencil beam scanning (PBS) spots. Such a pattern has been used previously for quality assurance purposes to assess spot shape, position, and dose. Methods: In this study, a scintillation detector was used to measure the test pattern in air at isocenter for two proton beam energies (115 and 225 MeV) of two IBA universal nozzles (UN #1 and UN #2). Planar measurements were compared with calculated dose distributions based on the weighted superposition of location-independent (UN #1) or location-dependent (UN #2) spot profiles, previously measured using a pair-magnification method and between two nozzles. Results: Including the halo component below 1% of the central dose is shown to improve the gamma-map comparison between calculation and measurement from 94.9% to 98.4% using 2 mm/2% criteria for the 115 MeV proton beam of UN #1. In contrast, including the halo component below 1% of the central dose does not improve the gamma agreement for the 115 MeV proton beam of UN #2, due to the cutoff of the halo component at off-axis locations. When location-dependent spot profiles are used for calculation instead of spot profiles at central axis, the gamma agreement is improved from 98.0% to 99.5% using 2 mm/2% criteria. The two nozzles clearly have different characteristics, as a direct comparison of measured data shows a passing rate of 89.7% for the 115 MeV proton beam. At 225 MeV, the corresponding gamma comparisons agree better between measurement and calculation, and between measurements in the two nozzles. Conclusions: In addition to confirming the primary component of individual PBS spot profiles, a comprehensive test pattern is useful for the validation of the halo component at off-axis locations, especially for low energy protons.

60 APPLIED LIFE SCIENCES↗

Patterning polycrystalline thin films by defocused ion beam: The influence of initial morphology on the evolution of self-organized nanostructures

We report on self-organized patterning of polycrystalline noble metal films, supported on dielectric substrates, by defocused Ar{sup +} ion beam irradiation. The initial surface morphology affects the formation of nanostructures, forcing the growth of ripples with a lateral periodicity imposed by the pristine polycrystalline grain distribution. At the early stages, the self-organization process is dominated by the shadowing of taller grains, while a crossover to the conventional erosive regime, observed for single crystals, sets in at longer sputtering times. The grain boundaries, although providing an additional bias for diffusion of mobile defects, do not affect the propagation of nanoscale ripples across individual grains.

36 MATERIALS SCIENCE↗

Optically enhanced patternable photosensitivity via oxygen excitation

The present disclosure relates to a method for performing a three dimensional (3D) printing process. A primary light beam having a wavelength sufficient to initiate polymerization of a photoresin is generated and patterned into a patterned primary beam. The patterned primary beam is directed toward an ultraviolet (UV) or visible light sensitive photoresin to initiate polymerization of select areas of the photoresin. The photoresin is also illuminated with a secondary light beam having a wavelength of at least one of about 765 nm, 1064 nm, or 1273 nm. The secondary light beam stimulates triplet oxygen into singlet oxygen, which controls oxygen inhibition in additional areas bordering the select areas, to enable controlled polymerization inhibition in the additional areas bordering the select areas.

Hensleigh, Ryan↗

Fast Electromechanical Switches Based on Carbon Nanotubes

Electrostatically actuated nanoelectromechanical switches based on carbon nanotubes have been fabricated and tested in a continuing effort to develop high-speed switches for a variety of stationary and portable electronic equipment. As explained below, these devices offer advantages over electrostatically actuated microelectromechanical switches, which, heretofore, have represented the state of the art of rapid, highly miniaturized electromechanical switches. Potential applications for these devices include computer memories, cellular telephones, communication networks, scientific instrumentation, and general radiation-hard electronic equipment. A representative device of the present type includes a single-wall carbon nanotube suspended over a trench about 130 nm wide and 20 nm deep in an electrically insulating material. The ends of the carbon nanotube are connected to metal electrodes, denoted the source and drain electrodes. At bottom of the trench is another metal electrode, denoted the pull electrode (see figure). In the off or open switch state, no voltage is applied, and the nanotube remains out of contact with the pull electrode. When a sufficiently large electric potential (switching potential) is applied between the pull electrode and either or both of the source and drain electrodes, the resulting electrostatic attraction bends and stretches the nanotube into contact with the pull electrode, thereby putting the switch into the "on" or "closed" state, in which substantial current (typically as much as hundreds of nanoamperes) is conducted. Devices of this type for use in initial experiments were fabricated on a thermally oxidized Si wafer, onto which Nb was sputter-deposited for use as the pull-electrode layer. Nb was chosen because its refractory nature would enable it to withstand the chemical and thermal conditions to be subsequently imposed for growing carbon nanotubes. A 200- nm-thick layer of SiO2 was formed on top of the Nb layer by plasma-enhanced chemical vapor deposition. In the device regions, the SiO2 layer was patterned to thin it to the 20-nm trench depth. The trenches were then patterned by electron- beam lithography and formed by reactive- ion etching of the pattern through the 20-nm-thick SiO2 to the Nb layer.

Kaul, Anupama↗

Evidence of auroral plasma cavities at Uranus and Neptune from radio burst observations

Radio bursts originating from the stronger magnetic polar regions of both Uranus and Neptune were detected by the planetary radio astronomy experiment during the Voyager 2 encounters with the planets. It has previously been demonstrated that these bursts are beamed into a broad, hollow emission pattern from their auroral sources. It is now shown that the bursts at both planets also manifest similar detailed patterns, with the waves beamed into two separate and distinct radiation cones at intermediate wave frequencies. This double-cone emission pattern is predicted by relativistic cyclotron resonance theory, and application of this theory to the observed emission pattern yields the plasma density structure within the radio source region. Calculations indicate that at both Uranus and Neptune the plasma-to-cyclotron frequency ratio can drop well below 0.01 within the active region. Such low values indicate that the southern auroral zones at both planets contain an auroral plasma cavity that is similar to that found in earth's nightside auroral zone.

Farrell, W. M.↗

Optically enhanced patternable photosensitivity via oxygen excitation

A method is disclosed for performing a three dimensional (3D) printing process. The method involves generating a primary light beam having a wavelength sufficient to initiate polymerization of a photoresin, and patterning the primary light beam into a patterned primary beam. The patterned primary beam may be directed toward an ultraviolet (UV) or visible light sensitive photoresin to initiate polymerization of select areas of the photoresin. The photoresin may be illuminated with a secondary light beam having a wavelength of about 765 nm to stimulate triplet oxygen into singlet oxygen, to thus control oxygen inhibition in additional areas bordering the select areas, to control polymerization inhibition in the additional areas bordering the select areas.

36 MATERIALS SCIENCE↗

High-Resolution Three-Dimensional Sculpting of Two-Dimensional Graphene Oxide by E-Beam Direct Write

On demand switchable additive/subtractive patterning of 2D nanomaterials is an essential capability for developing new concepts of functional nanomaterials and their device realizations. Traditionally, this is performed via a multi-step process using photoresist coating and patterning by conventional photo or electron beam lithography, which is followed by bulk dry/wet etch or deposition. This limits the range of functionalities and structural topologies that can be achieved, as well as increases the complexity, cost, and possibility of contamination which are significant barriers to device fabrication from highly sensitive 2D materials. Focused electron beam induced processing (FEBIP) enables a material chemistry/site-specific, high-resolution multi-mode atomic scale processing and provides unprecedented opportunities for direct-write, single-step surface patterning of 2D nanomaterials with an in-situ imaging capability. It allows for realizing a rapid multi-scale/multi-mode approach, ranging from an atomic scale manipulation (e.g., via targeted defect introduction as an active site) to a large-area surface modification on nano and micro scales, including patterned doping and material removal/deposition with 2D (in-plane)/3D (out-of-plane) control. In this work, we report on a new capability of FEBIP for nanoscale patterning of graphene oxide via removal of oxygenated carbon moieties with no use of reactive gas required for etching complemented by carbon atom deposition using focused electron beam. The mechanism of experimentally observed phenomena is explored using the density functional theory (DFT) calculations, revealing that interactions of e-beam liberated reactive oxygen radicals with carbon atoms on graphene basal plane lead to creation of atomic vacancies in the material. The reaction by-products are volatile carbon di-oxides, which are dissociated and volatilized from the graphene oxide surface functional groups by interactions with an energetic focused electron beam. Along with selective “subtractive” patterning of graphene oxide, the same electron beam with increased irradiation doses can deposit out-of-plane 3D carbon nanostructures on top of or around the 2D etched pattern, thus forming a hybrid 2D/3D nanocomposite with feature control down to a few nanometers. Furthermore, this in-operando dual nanofabrication capability of FEBIP is unmatched by any other nanopatterning techniques and opens a new design window for forming 2D/3D complex nanostructures and functional nanodevices.

36 MATERIALS SCIENCE↗

Integral dose investigation of non-coplanar treatment beam geometries in radiotherapy

Purpose: Automated planning and delivery of non-coplanar plans such as 4π radiotherapy involving a large number of fields have been developed to take advantage of the newly available automated couch and gantry on C-arm gantry linacs. However, there is an increasing concern regarding the potential changes in the integral dose that needs to be investigated. Methods: A digital torso phantom and 22 lung and liver stereotactic body radiation therapy (SBRT) patients were included in the study. The digital phantom was constructed as a water equivalent elliptical cylinder with a major axis length of 35.4 cm and minor axis of 23.6 cm. A 4.5 cm diameter target was positioned at varying depths along the major axis. Integral doses from intensity modulated, non-coplanar beams forming a conical pattern were compared against the equally spaced coplanar beam plans. Integral dose dependence on the phantom geometry and the beam number was also quantified. For the patient plans, the non-coplanar and coplanar beams and fluences were optimized using a column generation and pricing approach and compared against clinical VMAT plans using two full (lung) or partial coplanar arcs (liver) entering at the side proximal to the tumor. Both the average dose to the normal tissue volume and the total volumes receiving greater than 2 Gy (V2) and 5 Gy (V5) were evaluated and compared. Results: The ratio of integral dose from the non-coplanar and coplanar plans depended on the tumor depth for the phantom; for tumors shallower than 10 cm, the non-coplanar integral doses were lower than coplanar integral doses for non-coplanar angles less than 60°. Similar patterns were observed in the patient plans. The smallest non-coplanar integral doses were observed for tumor 6–8 cm deep. For the phantom, the integral dose was independent of the number of beams, consistent with the liver SBRT patients but the lung SBRT patients showed slight increase in the integral dose when more beams were used. Larger tumor size and larger patient body size did not change the overall relationship of integral doses between non-coplanar and coplanar cases. However, the thin disk-shaped tumor received at least 40% greater integral doses with the non-coplanar plans. Overall, patient non-coplanar integral doses and V5 were comparable to those of coplanar doses from the same optimization engine and 15%–20% lower than state of the art VMAT plans. However, non-coplanar beams significantly increased V2 in both the phantom and patients. On average, the lung and liver SBRT patient normal tissue volumes receiving dose greater than 2 Gy were increased by 749 and 532 cm{sup 3}, respectively. Conclusions: The authors used a digital phantom simulating a patient torso and 22 SBRT patients to show that the integral doses from the plans employing optimized non-coplanar beams are comparable to those of the coplanar plans using an equal number of discrete beams and are significantly lower than those of VMAT plans. The non-coplanar beams expose a larger normal tissue volume to non-zero doses, whose impact will need to be evaluated individually to determine the risk/benefit ratio of the non-coplanar plans.

61 RADIATION PROTECTION AND DOSIMETRY↗