Results for “performance optimization” — Page 19

NASA NTRS1986

Preliminary test data using the MOS DRO with Si:In detector material

The initial testing performed on the Hughes Metal Oxide Semiconductor Direct Readout (MOS DRO) with a Si:In extrinsic infrared array is described. The testing to date was of a screening nature and the results are primarily qualitative rather than quantitative. At a later date the performance optimization phase will be initiated. An encouraging result is that this response is strongly dependent on the detector temperature, to the extent that thermal transients introduced during the chip readout will affect the performance. A responsivity of 1 A/W at 2.2 microns with a bias of 15 volts, which is well below what is optimum bias, was obtained.

Fowler, A. M.↗

NASA NTRS2004

Sensor Needs for Control and Health Management of Intelligent Aircraft Engines

NASA and the U.S. Department of Defense are conducting programs which support the future vision of "intelligent" aircraft engines for enhancing the affordability, performance, operability, safety, and reliability of aircraft propulsion systems. Intelligent engines will have advanced control and health management capabilities enabling these engines to be self-diagnostic, self-prognostic, and adaptive to optimize performance based upon the current condition of the engine or the current mission of the vehicle. Sensors are a critical technology necessary to enable the intelligent engine vision as they are relied upon to accurately collect the data required for engine control and health management. This paper reviews the anticipated sensor requirements to support the future vision of intelligent engines from a control and health management perspective. Propulsion control and health management technologies are discussed in the broad areas of active component controls, propulsion health management and distributed controls. In each of these three areas individual technologies will be described, input parameters necessary for control feedback or health management will be discussed, and sensor performance specifications for measuring these parameters will be summarized.

Simon, Donald L.↗

DOE OSTI2026

Revealing the Full Potential of Glycolated Mixed Ionic-Electronic Semiconductors – Symmetric Monomer Polymerization to Boost Electrochemical Transistor Performance

Organic electrochemical transistors (OECTs) enable the transduction of ionic signals into electronic outputs, positioning them as ideal candidates for next-generation sensing and (bio)signal processing applications. Recent years have witnessed the development of various OECT channel materials, affording insights into structural fine-tuning to achieve optimal performance and/or stability. However, homocouplings, commonly present in alternating conjugated polymers, have largely been overlooked. This study investigates the effect of homocoupling on OECT materials by employing two synthesis methods – standard Stille polymerization and an alternative symmetric approach – to create the p-type enhancement-mode benchmark polymer pgBTTT. The impact of homocoupling, and its absence, is studied by comparing the bulk properties of the two polymers and evaluating their respective OECT metrics. The new, homocoupling-free polymer exhibits a notably improved OECT performance ( μC *), mainly due to an average 3-fold increase in electronic mobility (μ).

defects↗

NASA NTRS1990

Structural and optical properties for typical solid mirror shapes

A method is developed to determine the weight, center of gravity, areal properties, and mass inertial properties for typical mirrors. A number of support conditions were considered to examine optical surface deflections, surface quality, and fundamental natural frequency for single- and double-arch mirror shapes. Structural performance estimates were made with the NASTRAN program, and optical performances were evaluated with the FRINGE program, using an SXA 40-in mirror. To show the behavior of element types from the NASTRAN program, finite element validity and sensitivity studies were performed in optical model applications. Material parameters, contoured back shapes, and support locations are shown to have significant effects on structural and optical performances. Optimal support locations and support points are given. Fundamental natural frequencies for some shapes are found with the closed-form solution. The plate models results may not be acceptable for determining real mirror optical performances.

Cho, Myung K.↗

DOE OSTI2024

LSAFE: a Lightweight Static Analysis Framework for binary Executables

Static analysis is a widely used technique for analyzing various aspects of programs. However, as programs become more complex, static analysis tools require larger resources, such as CPU time and memory, to perform the same tasks. Moreover, the source code of programs may not always be accessible, requiring static analysis to be performed on the binary executable code directly. To overcome these challenges, we propose a lightweight static analysis framework called LSAFE, which constructs control flow graphs (CFGs) and data dependency graphs (DDGs) of target programs with optimized performance in terms of CPU and memory usage. We evaluated the proposed framework using both Spec benchmark programs and real-world industrial applications, and found that it outperformed Angr, an existing state-of-the-art static analysis tool. Additionally, we demonstrate a case study that utilizes the CFG generated by LSAFE to detect memory leaks.

Qu, Guangzhi↗

DOE OSTI2026

ORCHA: A performance portability system for extreme heterogeneity

Heterogeneity is the prevalent trend in the rapidly evolving high-performance computing (HPC) landscape in both hardware and application software. The diversity in hardware platforms, currently comprising various accelerators and a future possibility of specializable chiplets, poses a significant challenge for scientific software developers aiming to harness optimal performance across different computing platforms while maintaining the quality of solutions when their applications are simultaneously growing more complex. Code synthesis and code generation can provide mechanisms to mitigate this challenge. We have developed a divide and conquer approach where different aspects of performance are handled by different stand-alone tools that are interfaced with the application through generated code. This portability system, ORCHA, enables users to configure and orchestrate their computations among available resources on a platform by specifying a high-level recipe, thereby permitting a many-to-many paradigm where each recipe results in a different variant of the application. The core design goal is to let users decide the application’s hardware mapping and orchestration by editing only the high-level recipe—without modifying the maintained source code or binding the application to a particular runtime system. Tools in ORCHA distribution are: CG-Kit for translating the recipe into an execution graph; Milhoja to execute the graph by orchestrating data and task movement among hardware resources; and Macroprocessor that enables users to define their own code-shorthand for higher composability and easier management of code variants. Additionally, the design of ORCHA permits tools to work in a plug-and-play mode where the application can build and run without CG-Kit and Milhoja, and either tool can be swapped out for other tools with similar capabilities by modifying the code generation portion of ORCHA. In this paper, we describe the design of ORCHA and the role that code-generation plays in isolating applications from tools. We demonstrate the breadth of configurations ORCHA enables with a case study in which an application configuration is realized on three distinct hardware mappings—a GPU-centric, a CPU/GPU balanced, and a CPU/GPU concurrent layouts by using different recipes.

Lee, Youngjun↗

DOE OSTI2025

Development of a Digital Twin for Hydrogen Dispersion and Safety Assessment in an Electrolyzer Based Hydrogen Production Facility

Digital twin models are virtual representations of physical systems that use real-time data to simulate and optimize performance. This study presents the development and initial implementation of a digital twin (DT) for the electrolyzer-based hydrogen production facility at NREL's Advanced Research on Integrated Energy Systems (ARIES), focused on enhancing safety and optimizing sensor placement through physics-based simulations and metadata integration. The DT incorporates detailed facility-specific information, including component layout, leak locations, and controlled release parameters, to model hydrogen dispersion under varying environmental conditions. Using steady-state computational fluid dynamics (CFD) simulations informed by real meteorological data, such as wind speed, direction, and vertical wind profiles, the DT enables visualization of hydrogen plume behavior and spatial concentration distributions. Comparative analysis between high and low wind speed scenarios illustrates the significant influence of wind dynamics on plume shape and extent, with horizontal momentum dominating dispersion at higher speeds, while buoyancy effects become more prominent under low wind conditions. These simulations generate a rich dataset embedded within the DT, allowing users to assess potential leak outcomes and identify optimal sensor locations based on concentration thresholds. The model supports scenario-based analysis to guide safety strategies and equipment deployment for open-area hydrogen infrastructure. The digital twin thus serves as a dynamic platform for virtual prototyping, providing predictive insight into hydrogen behavior and enhancing risk-informed decision-making. This initial phase establishes a validated foundation for future integration of transient, uncontrolled leak scenarios and real-time sensor feedback, positioning the DT as a critical tool for safety design, operational planning, and adaptive monitoring in hydrogen systems. Overall, the approach demonstrates the value of combining environmental data with digital simulations to inform safer and more efficient deployment of hydrogen technologies.

08 HYDROGEN↗

DOE OSTI2025

Analyze the real-time performance of the optimized fiber-PTR instrument

An instrument to perform in-reactor, real-time thermal property measurements of nuclear fuels and materials was recently designed, optimized, and tested at Massachusetts Institute of Technology Research Reactor. It was the second insertion experiments of a total of two rounds. Here we report the collection and analysis of the real-time captured thermal diffusivity data on the preloaded SiC. With the optimized design, the instrument temperature had been successfully raised as we expected. Only one probe (the top one) returned real-time thermal diffusivity in a time span of approximately two days. Measured thermal diffusivity of the preloaded SiC was significantly lower than the literature value at the same temperature, indicating a significant influence from the irradiation induced microstructure damage. Meanwhile, the real-time thermal diffusivity value continuously reduced with time, indicating the dynamic microstructure evolution. The possible reasons of the probes that did not return data were hypothesized. The further optimization of the instrument with the objective to improve the measurement accuracy and instrument survivability is also discussed.

36 MATERIALS SCIENCE↗

NASA NTRS1989

Integrated multidisciplinary design optimization of rotorcraft

The NASA/Army research plan for developing the logic elements for helicopter rotor design optimization by integrating appropriate disciplines and accounting for important interactions among the disciplines is discussed. The paper describes the optimization formulation in terms of the objective function, design variables, and constraints. The analysis aspects are discussed, and an initial effort at defining the interdisciplinary coupling is summarized. Results are presented on the achievements made in the rotor aerodynamic performance optimization for minimum hover horsepower, rotor dynamic optimization for vibration reduction, rotor structural optimization for minimum weight, and integrated aerodynamic load/dynamics optimization for minimum vibration and weight.

Adelman, Howard M.↗

NASA NTRS2004

Human Motion Tracking at Marshall Space Flight Center's Collaborative Engineering Center ANVIL

The installation and use of electromagnetic human motion trackers requires a specially designed and metal-free environment for optimal performance. Such an area is not readily available at the Marshall Space Flight Center Collaborative Engineering Center ANVIL. Our paper details a systems engineering approach to installing and operating Ascension Technologies Ethernet MotionStar tracking system in a sub-optimal environment, used with the JACK human computer model's motion capture capabilities. We also discuss how this system is integrated into the Marshall Space Flight Center's Human Engineering process.

Henderson, Steven J.↗

NASA NTRS2016

High-Performance Reaction Wheel Optimization for Fine-Pointing Space Platforms: Minimizing Induced Vibration Effects on Jitter Performance plus Lessons Learned from Hubble Space Telescope for Current and Future Spacecraft Applications

The Hubble Space Telescope (HST) applies large-diameter optics (2.5-m primary mirror) for diffraction-limited resolution spanning an extended wavelength range (approx. 100-2500 nm). Its Pointing Control System (PCS) Reaction Wheel Assemblies (RWAs), in the Support Systems Module (SSM), acquired an unprecedented set of high-sensitivity Induced Vibration (IV) data for 5 flight-certified RWAs: dwelling at set rotation rates. Focused on 4 key ratios, force and moment harmonic values (in 3 local principal directions) are extracted in the RWA operating range (0-3000 RPM). The IV test data, obtained under ambient lab conditions, are investigated in detail, evaluated, compiled, and curve-fitted; variational trends, core causes, and unforeseen anomalies are addressed. In aggregate, these values constitute a statistically-valid basis to quantify ground test-to-test variations and facilitate extrapolations to on-orbit conditions. Accumulated knowledge of bearing-rotor vibrational sources, corresponding harmonic contributions, and salient elements of IV key variability factors are discussed. An evolved methodology is presented for absolute assessments and relative comparisons of macro-level IV signal magnitude due to micro-level construction-assembly geometric details/imperfections stemming from both electrical drive and primary bearing design parameters. Based upon studies of same-size/similar-design momentum wheels' IV changes, upper estimates due to transitions from ground tests to orbital conditions are derived. Recommended HST RWA choices are discussed relative to system optimization/tradeoffs of Line-Of-Sight (LOS) vector-pointing focal-plane error driven by higher IV transmissibilities through low-damped structural dynamics that stimulate optical elements. Unique analytical disturbance results for orbital HST accelerations are described applicable to microgravity efforts. Conclusions, lessons learned, historical context/insights, and perspectives on future applications are given; these previously unpublished data and findings represents a valuable resource for fine-pointing spacecraft or space-based platforms using RWAs, Control Moment Gyros (CMGs), Momentum Wheels, or other ball-bearing-based rotational units.

Hasha, Martin D.↗

DOE OSTI2025

Artificial Intelligence and Digital Engineering as Enablers for System Engineering in the Energy Sector

Systems engineering is of utmost importance for the success of high-cost, high-complexity megaprojects, which are common in the energy sector. However, the traditional document-centric systems engineering approach tends to be labor-intensive and time-consuming, which has inhibited its full adoption despite proven metrics on its return on investment. However, with the modern approach of digital engineering and technological advancements in artificial intelligence (AI) technologies, the barriers to systems engineering adoption can finally be broken. This paper goes through the systems engineering V-model for lifecycle management and assesses the current state of implementation of digital engineering (especially, mod-el-based systems engineering, digital twins, and digital threads) and AI for each step. It was observed that a combination of digital engineering and AI is being used across different industries to accelerate and optimize systems engineering processes such as concept development, requirements management, architecture definition, system development, verification and validation, operations, and maintenance. Specifically in the energy sector, AI-augmented digital engineering has shown initial potential in accelerated development and deployment, performance optimization, anomaly detection, predictive maintenance, and configuration management. However, challenges remain in integrating DE and AI into an end-to-end system lifecycle management ecosystem safely and reliably. Addressing these challenges and continuously developing impactful tools will enable fast, efficient, and high-frequency deployment of power generation capabilities to keep up with the world’s energy demands and build energy security.

42 - ENGINEERING↗

DOE OSTI2025

Artificial Intelligence and Digital Engineering as Enablers for Systems Engineering in the Energy Sector

Systems engineering is of utmost importance for the success of high-cost, high-complexity megaprojects, which are common in the energy sector. However, the traditional document-centric systems engineering approach tends to be labor-intensive and time-consuming, which has inhibited its full adoption despite proven metrics on its return on investment. However, with the modern approach of digital engineering and technological advancements in artificial intelligence (AI) technologies, the barriers to systems engineering adoption can finally be broken. This paper goes through the systems engineering V-model for lifecycle management and assesses the current state of implementation of digital engineering (especially, mod-el-based systems engineering, digital twins, and digital threads) and AI for each step. It was observed that a combination of digital engineering and AI is being used across different industries to accelerate and optimize systems engineering processes such as concept development, requirements management, architecture definition, system development, verification and validation, operations, and maintenance. Specifically in the energy sector, AI-augmented digital engineering has shown initial potential in accelerated development and deployment, performance optimization, anomaly detection, predictive maintenance, and configuration management. However, challenges remain in integrating DE and AI into an end-to-end system lifecycle management ecosystem safely and reliably. Addressing these challenges and continuously developing impactful tools will enable fast, efficient, and high-frequency deployment of power generation capabilities to keep up with the world?s energy demands and build energy security.

42 - ENGINEERING↗

NASA NTRS2012

Woven TPS - A New Approach to TPS Design and Manufacturing

NASA's Office of the Chief Technologist (OCT) Game Changing Division recently funded an effort to advance a Woven TPS (WTPS) concept. WTPS is a new approach to producing TPS materials that uses precisely engineered 3D weaving techniques to customize material characteristics needed to meet specific missions requirements for protecting space vehicles from the intense heating generated during atmospheric entry. Using WTPS, sustainable, scalable, mission-optimized TPS solutions can be achieved with relatively low life cycle costs compared with the high costs and long development schedules currently associated with material development and certification. WTPS leverages the mature state-of-the-art weaving technology that has evolved from the textile industry to design TPS materials with tailorable performance by varying material composition and properties via the controlled placement of fibers within a woven structure. The resulting material can be designed to perform optimally for a wide range of entry conditions encompassing NASAs current and future mission needs. WTPS enables these optimized TPS designs to be translated precisely into mission-specific, manufactured materials that can substantially increase the efficiency, utility, and robustness of heat shield materials compared to the current state-of-the-art material options. By delivering improved heat shield performance and affordability, this technology will impact all future exploration missions, from the robotic in-situ science missions to Mars, Venus and Saturn to the next generation of human missions. WTPS can change the way NASA develops, certifies, and integrates TPS into mission life cycles - instead of being a mission constraint, TPS will become a mission enabler. It is anticipated that WTPS will have direct impact on SMD, HEOMD and OCT and will be of interest for DoD and COTS applications. This presentation will overview the WTPS concept and present some results from initial testing completed.

Feldman, Jay↗

NASA NTRSDate not supplied

An Overview of Research in Nondestructive Evaluation at the National Aeronautics and Space Administration’s Langley Research Center

The primary focus of the nondestructive evaluation (NDE) effort at Langley Research Center (LaRC) is to pioneer advances in NDE and structural health monitoring (SHM) through fundamental scientific research, technology development, and transferring these to the scientific and aerospace communities. This research supports a variety of NASA missions in space operations, exploration and aeronautics. The work presented will focus on the development of advanced inspection systems to detect critical flaws in both metallic and non-metallic materials and structures for aerospace applications. The emphasis is on increasing the performance of inspection systems to provide defect detection and quantitative characterization of the material state. LaRC NDE utilizes expertise in computational ultrasonic, thermal and eddy current simulations to reduce measured responses to size and locations of flaws, establish technique limitations and optimize performance. This presentation will highlight research into five strategic areas: (1) The development of novel solutions using state-of-the-art NDE technologies such as eddy current, ultrasound, thermography and x-ray computed tomography; (2) Research in the development of unique NDE technologies such as terahertz, wavefield imaging and nonlinear ultrasound; (3) The application of both computational and analytic models to NDE problems; (4) The development of advanced analytic methods to interpret large complex data sets; and (5) Advanced methods of applying and interrogating sensors for structural health monitoring.

K Elliott Cramer↗

NASA NTRSDate not supplied

An Overview of Research in Nondestructive Evaluation at the National Aeronautics and Space Administration’s Langley Research Center

The primary focus of the nondestructive evaluation (NDE) effort at Langley Research Center (LaRC) is to pioneer advances in NDE and structural health monitoring (SHM) through fundamental scientific research, technology development, and transferring these to the scientific and aerospace communities. This research supports a variety of NASA missions in space operations, exploration and aeronautics. The work presented will focus on the development of advanced inspection systems to detect critical flaws in both metallic and non-metallic materials and structures for aerospace applications. The emphasis is on increasing the performance of inspection systems to provide defect detection and quantitative characterization of the material state. LaRC NDE utilizes expertise in computational ultrasonic, thermal and eddy current simulations to reduce measured responses to size and locations of flaws, establish technique limitations and optimize performance. This presentation will highlight research into five strategic areas: (1) The development of novel solutions using state-of-the-art NDE technologies such as eddy current, ultrasound, thermography and x-ray computed tomography; (2) Research in the development of unique NDE technologies such as terahertz, wavefield imaging and nonlinear ultrasound; (3) The application of both computational and analytic models to NDE problems; (4) The development of advanced analytic methods to interpret large complex data sets; and (5) Advanced methods of applying and interrogating sensors for structural health monitoring.

NDE↗

DOE OSTI2026

Development of a Digital Twin for Hydrogen Dispersion and Safety Assessment in an Electrolyzer-Based Hydrogen Production Facility: Preprint

Digital twin models are virtual representations of physical systems that use real-time data to simulate and optimize performance. This study presents the development and initial implementation of a digital twin (DT) for the electrolyzer-based hydrogen production facility at the National Renewable Energy Laboratory (NREL)'s Advanced Research on Integrated Energy Systems (ARIES), focused on enhancing safety and optimizing sensor placement through physics-based simulations and metadata integration. The DT incorporates detailed facility-specific information, including component layout, leak locations, and controlled release parameters, to model hydrogen dispersion under varying environmental conditions. Using steady-state computational fluid dynamics (CFD) simulations informed by real meteorological data, such as wind speed, direction, and vertical wind profiles, the DT enables visualization of hydrogen plume behavior and spatial concentration distributions. Comparative analysis between high and low wind speed scenarios illustrates the significant influence of wind dynamics on plume shape and extent, with horizontal momentum dominating dispersion at higher speeds, while buoyancy effects become more prominent under low wind conditions. These simulations generate a rich dataset embedded within the DT, allowing users to assess potential leak outcomes and identify optimal sensor locations based on concentration thresholds. The model supports scenario-based analysis to guide safety strategies and equipment deployment for open-area hydrogen infrastructure. The digital twin thus serves as a dynamic platform for virtual prototyping, providing predictive insight into hydrogen behavior and enhancing risk-informed decision-making. This initial phase establishes a validated foundation for future integration of transient, uncontrolled leak scenarios and real-time sensor feedback, positioning the DT as a critical tool for safety design, operational planning, and adaptive monitoring in hydrogen systems. Overall, the approach demonstrates the value of combining environmental data with digital simulations to inform safer and more efficient deployment of hydrogen technologies.

08 HYDROGEN↗

NASA NTRSDate not supplied

An Optimal Estimation Aerosol Retrieval Algorithm for Lidar-only and Combined Lidar Polarimeter Remote Sensors

Global measurements of aerosol vertical profile, composition, concentration, and size distribution are very important due to aerosol impacts on air quality, climate, clouds, and ocean ecosystems. We have developed a lidar-only and combined lidar and polarimeter algorithm to retrieve vertically-resolved profiles of aerosol microphysical properties. The new retrieval system is modular in design. It consists of three modules, a vertically-resolved aerosol profile retrieval module for lidar data, an aerosol and cloud/ocean retrieval module for polarimeter data, and a combined retrieval module for both lidar and polarimeter measurements. In addition to performing optimal estimation retrievals on various data sources, we have designed the system so that it can be used to carry out aerosol retrieval performance trade studies for various lidar and polarimeter configurations. For example, the retrieval system can take inputs from attenuated backscatter lidar at two wavelengths (e.g. CALIPSO like instrument), aerosol backscattering measured at two wavelengths and and aerosol extinction measured at one wavelength (HSRL-1), or aerosol backscattering measured at three wavelengths and aerosol extinction measured at two wavelengths (HSRL-1) (HSRL-2). We have applied the lidar-only algorithm to both simulated data and various field campaign data (DISCOVER-AQ, CHARMS, TCAP, and ORACLES). For polarimeter-only modules, we have done the same for SABOR, TCAP, NAAMES, and ORACLES data. We have applied the combined retrieval algorithm to ORACLES data. The simulated retrieval studies show that the combined lidar+polarimeter retrieval provides much higher information content relative to their individual counterparts for retrieving effective radius, particle concentrations, and absorption properties.

Xu Liu↗