Results for “phase current limiter” — Page 19

NASA NTRS2014

Micro-spec: an Integrated Direct-detection Spectrometer for Far-infrared Space Telescopes

The far-infrared and submillimeter portions of the electromagnetic spectrum provide a unique view of the astrophysical processes present in the early universe. Our ability to fully explore this rich spectral region has been limited, however, by the size and cost of the cryogenic spectrometers required to carry out such measurements.Micro-Spec (μ-Spec) is a high-sensitivity, direct-detection spectrometer concept working in the 450-1000 (micrometers) wavelength range which will enable a wide range of flight missions that would otherwise be challenging due tothe large size of current instruments with the required spectral resolution and sensitivity. The spectrometer design utilizes two internal antenna arrays, one for transmitting and one for receiving, superconducting microstrip transmission lines for power division and phase delay, and an array of microwave kinetic inductance detectors (MKIDs) to achieve these goals. The instrument will be integrated on a approximately 10 sq cm silicon chip and can therefore become an important capability under the low background conditions accessible via space and high-altitude borne platforms. In this paper, an optical design methodology for micro-Spec is presented, with particular attention given to its two-dimensional diffractive region, where the light of different wavelengths is focused on the different detectors. The method is based on the maximization of the instrument resolving power and minimization of the RMS phase error on the instrument focal plane. This two-step optimization can generate geometrical configurations given specific requirements on spectrometer size, operating spectral range and performance.Two point designs with resolving power of 260 and 520 and an RMS phase error less than approximately 0.004 radians were developed for initial demonstration and will be the basis of future instruments with resolving power up to about 1200.

Far-infrared↗

NASA NTRS1983

Advanced ion thruster and electrochemical launcher research

The theoretical model of orificed hollow cathode operation predicted experimentally observed cathode performance with reasonable accuracy. The deflection and divergence characteristics of ion beamlets emanating from a two grid optics system as a function of the relative offset of screen and accel grids hole axes were described. Ion currents associated with discharge chamber operation were controlled to improve ion thruster performance markedly. Limitations imposed by basic physical laws on reductions in screen grid hole size and grid spacing for ion optics systems were described. The influence of stray magnetic fields in the vicinity of a neutralizer on the performance of that neutralizer was demonstrated. The ion current density extracted from a thruster was enhanced by injecting electrons into the region between its ion accelerating grids. Theoretical analysis of the electrothermal ramjet concept of launching space bound payloads at high acceleration levels is described. The operation of this system is broken down into two phases. In the light gas gun phase the payload is accelerated to the velocity at which the ramjet phase can commence. Preliminary models of operation are examined and shown to yield overall energy efficiences for a typical Earth escape launch of 60 to 70%. When shock losses are incorporated these efficiencies are still observed to remain at the relatively high values of 40 to 50%.

Wilbur, P. J.↗

NASA NTRS2002

Miniature Heat Transport System for Spacecraft Thermal Control

Loop heat pipes (LHP) are efficient devices for heat transfer and use the basic principle of a closed evaporation-condensation cycle. The advantage of using a loop heat pipe over other conventional methods is that large quantities of heat can be transported through a small cross-sectional area over a considerable distance with no additional power input to the system. By using LHPs, it seems possible to meet the growing demand for high-power cooling devices. Although they are somewhat similar to conventional heat pipes, LHPs have a whole set of unique properties, such as low pressure drops and flexible lines between condenser and evaporator, that make them rather promising. LHPs are capable of providing a means of transporting heat over long distances with no input power other than the heat being transported because of the specially designed evaporator and the separation of liquid and vapor lines. For LHP design and fabrication, preliminary analysis on the basis of dimensionless criteria is necessary because of certain complicated phenomena that take place in the heat pipe. Modeling the performance of the LHP and miniaturizing its size are tasks and objectives of current research. In the course of h s work, the LHP and its components, including the evaporator (the most critical and complex part of the LHP), were modeled with the corresponding dimensionless groups also being investigated. Next, analysis of heat and mass transfer processes in the LHP, selection of the most weighted criteria from known dimensionless groups (thermal-fluid sciences), heat transfer rate limits, (heat pipe theory), and experimental ratios which are unique to a given heat pipe class are discussed. In the third part of the report, two-phase flow heat and mass transfer performances inside the LHP condenser are analyzed and calculated for Earth-normal gravity and microgravity conditions. On the basis of recent models and experimental databanks, an analysis for condensing two-phase flow regimes, pressure gradients, and local heat transfer coefficients using ammonia, propylene, and R134, are carried out.

Ochterbeck, Jay M.↗

NASA NTRS1991

Compatibility of potential reinforcing ceramics with Ni and Fe aluminides

There is a great deal of interest in the possible utilization of intermetallic compounds in advanced high temperature gas turbine engines. These compounds exhibit a variety of promising properties, including reasonable strength, high melting points, relatively low densities, and good corrosion resistance. However, in general, they also show limited ductilities and toughness, and less than optimum creep strengths at elevated temperatures. In addition, in applications involving advanced gas turbine engines, it is often necessary for candidate materials to have large elastic moduli. The present study is part of a program whose objective is to identify a high temperature fiber reinforced composite. The approach adopted was to fabricate laboratory samples of the combinations of materials considered by Misra, in order to determine the extent to which the thermodynamic calculations can predict phase stability. As many of the ceramic phases considered are not currently available in fiber form, they were added as particulates to the alloy matrices. The ways in which the materials were produced and evaluated are described.

Clark, William A. T.↗

NASA NTRS1976

Ring current proton decay by charge exchange

Explorer 45 (S3-A) measurements were made during the recovery phase of the moderate magnetic storm of February 24, 1972, in which a symmetric ring current had developed and effects due to asymmetric ring current losses could be eliminated. It was found that after the initial rapid decay of the proton flux, which is a consequence of the dissipation of the asymmetric ring current, the equatorially mirroring protons in the energy range 5-30 keV decayed throughout the L value range of 3.5-5.0 at the charge exchange decay rate calculated by Liemohn (1961). After several days of decay, the proton fluxes reached a lower limit where an apparent equilibrium was maintained, between weak particle source mechanisms and the loss mechanisms, until fresh protons were injected into the ring current region during substorms. While other proton loss mechanisms may also be operating, the results indicate that charge exchange is more than sufficient as a particle loss mechanism for the storm time proton ring current decay.

Smith, P. H.↗

NASA NTRS2014

Micro-Spec: an Integrated, Direct-Detection Spectrometer for Far-Infrared and Submillimeter Astronomy

The far-infrared and submillimeter portions of the electromagnetic spectrum provide a unique view of the astrophysical processes present in the early universe. Our ability to fully explore this rich spectral region has been limited, however, by the size and cost of the cryogenic spectrometers required to carry out such measurements. Micro-Spec (u-Spec) is a high-sensitivity, direct-detection spectrometer concept working in the 450-1000 micromillimeter wavelength range which will enable a wide range of flight missions that would otherwise be challenging due to the large size of current instruments with the required spectral resolution and sensitivity. The spectrometer design utilizes two internal antenna arrays, one for transmitting and one for receiving, superconducting microstrip transmission lines for power division and phase delay, and an array of microwave kinetic inductance detectors (MKIDs) to achieve these goals. The instrument will be integrated on a approximately 10 square cm silicon chip and can therefore become an important capability under the low background conditions accessible via space and high-altitude borne platforms. In this paper, an optical design methodology for Micro-Spec is presented, with particular attention given to its twodimensional diffractive region, where the light of different wavelengths is focused on the different detectors. The method is based on the maximization of the instrument resolving power and minimization of the RMS phase error on the instrument focal plane. This two-step optimization can generate geometrical configurations given specific requirements on spectrometer size, operating spectral range and performance. A point design with resolving power of 257, an RMS phase error less than 0.1 radians and four stigmatic points was developed for initial demonstration and will be the basis of future instruments with resolving power up to about 1200.

microwave kinetic inductance detectors (MKIDs)↗

NASA NTRS2016

Evaluation of Modeled Vertical Distribution of Atmospheric SO2 and Sulfate in UTLS

We evaluated the vertical profiles of both SO2 and sulfate in the AEROCOM (Aerosol Model Intercomparison) Phase II participating models. SO2 and sulfate show significant concentration gradient in both horizontal and vertical directions. Both online and offline aerosol transport models show large difference in the vertical distribution of sulfur species from surface all the way up to lower stratosphere. Comparison with available aircraft measurements suggests models agree with observations well when SO2 concentration is high. For the volcanic plumes, the injection height and magnitude determines initial SO2 plume distribution and following transport pattern. At high altitude, where the background concentration of SO2 is often below the detection limit of the current aircraft instruments and satellite retrievals, modeled SO2 and sulfate concentration, lifetime, and budget, as well as their uncertainties can be difficult to be accurately quantified.

volcanic plumes↗

NASA NTRSDate not supplied

Vapor Growth of ZnSe-based Compound Semiconductors in Low Gravity environment on International Space Station

Six low-gravity experiments of crystal growth of ZnSe-based compound semiconductors by physical vapor transport (PVT) are scheduled to be processed inside Low Gradient Furnace (LGF) on Materials Science Research Rack (MSRR) in Material Science Laboratory (MSL) on International Space Station (ISS) starting from February 27th, 2023. The flight samples consist of three unseeded growths of ZnSe, Cr-doped ZnSe and ZnSeTe as well as growth of ZnSe on top of three single crystal ZnSe seeds with orientation of (100), (110) and (111). The main scientific objective of the flight experiments is to establish the effects of gravity-driven fluid flows on Earth to (i) the non-uniform incorporation of impurities and defects and (ii) the deviation from stoichiometry observed in the grown crystals caused by growth interface fluctuations and evolution as the results of buoyancy-driven convection and irregular fluid-flows. The investigation will also evaluate the effects of gravity on the PVT process by examining (i) the growth kinetics on various seed orientations, (ii) the dopant segregation and distribution in the Cr doped ZnSe, and (iii) the compositional segregation and distribution in the ternary ZnSeTe crystal grown by PVT. Additionally, from X-ray diffraction/topography and by measuring the density and distribution of various crystalline defects it will assess the self-induced strain effects developed during processing at elevated temperatures caused by the weight of the crystals. During the ground-based preparations, the following tasks have been accomplished: • Establish the thermodynamic properties of the ZnSe binary and related ternary systems by measuring the partial pressures of the vapor phase coexisting with the condensed phases and perform phase diagram calculations for comparison. • Evaluate the effects of gravity-driven convection in the growth process by performing experiments under various vapor transport orientations relative to gravity vector, i.e., horizontal, vertically stabilized and destabilized configurations. • Establish a quantitative correlation between growth parameters and the characteristics and properties of the grown crystals by characterizing the crystals using a variety of techniques. • Evaluate the fundamentals of the current theories on vapor transport and crystal growth kinetics by performing in-situ and real-time monitoring techniques during growth. • Develop a one-dimensional diffusion limited theory of mass transport and two- and three-dimensional numerical simulations of both mass transport and heat transfer and thus establish the microgravity requirements for the flight experiments and to predict the characteristics of the grown crystals such as the solid-vapor interface shapes… etc. and establish a fundamental understanding of the crystal growth process from the comparison with experimental results.

ZnSe↗

NASA NTRSDate not supplied

A Survey of ISS and Visiting Vehicle Returned Surfaces for Environmental Characterization and Computer Model Development

The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.

Phillip Anz-meador↗

NASA NTRSDate not supplied

A Survey of ISS and Visiting Vehicle Returned Surfaces for Environmental Characterization and Computer Model Development

The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.

Phillip Anz-Meador↗

NASA NTRSDate not supplied

Decision Aid for Conjunction Risk Mitigation by Differential Drag

In the previous five years, the rate of conjunctions that the NASA Conjunction Assessment Risk Analysis (CARA) team processed and analyzed has more than tripled. (NASA CARA, 2024) New missions in the early development phases are now required to plan for dealing with conjunctions under the present space environment, and also projecting forward into a future likely with even further increased utilization of the space environment. Some missions are investigating the possibility of using differential drag to remediate conjunctions without expending limited fuel or for missions without propulsive capabilities. The NASA CARA team studied the historical record of conjunctions to evaluate the circumstances under which differential drag may be successfully applied and have developed a series of tables to use as a decision aid for missions considering differential drag. Currently, if a CARA-protected mission with maneuvering capabilities is predicted to have a conjunction with probability of collision (Pc) greater than 7E-5 (the default value of the ‘yellow threshold’, which may have some other value agreed by CARA and the mission during the Orbital Collison Avoidance Planning (OCAP) process), CARA will use its Maneuver Trade Space (MTS) tool to evaluate and recommend options for the timing and magnitude of a risk mitigation maneuver (RMM), based on the mission’s capabilities. If the conjunction’s Pc is greater than 1E-4, the ‘red threshold’, then an RMM must be executed per NASA Procedural Requirements (NPR) 8079.1 (NASA, 2023), although missions may execute an RMM even if the Pc is lower. The magnitude of the maneuver is typically a few cm/s, and CARA estimates how many will be required for the mission’s nominal lifetime – typically a few per year – during the OCAP process, to inform the mission’s delta-V requirement. For traditional satellites, this is usually smaller than other requirements for orbit insertion, maintenance, and disposal, but for CubeSats or other small satellite missions, a propulsion system may not provide much more than a few cm/s of delta-V or may not fit at all within the available budget of money, time, size, weight, and/or power (SWaP). Conversely, CubeSats often have deployable solar panels, which offer the capacity to have much higher areas facing some directions than others. Such a mission can instead use ‘differential drag’ to remediate a conjunction -- in other words, change its drag area (usually increasing) to deviate from the predicted collision course. This is how Planet’s Dove spacecraft maintain their formations and remediate conjunction risks without having on-board propulsion (Foster, et al., 2017) (Griffith, et al., 2021). CARA has been developing improvements to MTS to support differential-drag for NASA's missions -- where it is effective. CARA records all conjunctions of their protected payloads, with historical records starting in 2005 (with significant conjunction events starting to occur on or after 2013). From this record, approximately 7,300 had a Pc greater than 1E-4 at 3 days prior to the time of closest approach, the time analyzed for differential drag efficacy. Of those, approximately 4,300 had fully-defined covariance matrices stored for both the primary and secondary objects; this set of conjunctions is the basis for the analysis of this work. CARA’s MTS tool was used to propagate the primary satellite forward from that decision point with varying degrees of increase to ballistic coefficient (BC). Because these conjunctions came from multiple missions, the nondimensional ‘delta-BC’ factor was used to quantify and normalize the increase in ballistic coefficient, defined as follows: Delta-BC = BC_new / BC_old - 1 Positive delta-BC factors represent an increase in drag compared to the nominal attitude, while negative delta-BC factors (to a minimum of -1) represent a decrease in drag. At the conclusion of the differential-drag ‘maneuver’, the Pc was recalculated to evaluate whether or not the conjunction was mitigated (Pc < 3E-6). These results were then binned and sorted along several axes, including altitude, amount of delta-BC, and (pre-maneuver) rate of energy dissipation (EDR), to identify underlying patterns. The altitude plot is shown in Figure 1. To validate this analysis, we consulted the record of a NASA mission which uses differential drag to maintain its orbit and remediate conjunction risk. CARA’s empirical record of the mission’s orbit history suggests it achieves a delta-BC of 2.2. Of the twenty-one RMM plans that were submitted by this mission, eighteen were matched with conjunctions in the historical record; of those, twelve were successfully remediated (final measured Pc < 3E-6), and six were not. This is consistent with the expected efficacy for missions orbiting at that altitude. We are presently simulating this mission’s RMMs with MTS; this work is ongoing, but so far, the MTS results are qualitatively in agreement with the empirical results -- correctly predicting that a maneuver would or would not remediate a conjunction, if not exactly matching the final post-remediation Pc value. We found that differential drag was most successful for satellites with perigees below 560 km, and which could adopt an average delta-BC of 2 or greater (that is, increasing their ballistic coefficient by a factor of 3). However, this is a difficult threshold for a mission to clear; very few spacecraft are capable of adopting a high-drag configuration for 72 hours continuously. Planet’s Dove spacecraft use differential drag to remediate conjunctions (Griffith, et al., 2021), and they have a maximum delta-BC factor of 9, but in practice (with mission and charging constraints) they achieve a time-averaged delta-BC that is closer to 2 (Foster, et al., 2017). A mission’s differential drag utility strongly depends on the operational constraints that has the capacity to limit the time-averaged delta-BC. A mission with a high maximum delta-BC of 5 or more can have an effective delta-BC of less than 1 due to operational constraints such as instrument and solar panel pointing, especially if this constraint results in holding an intermediate drag value for most of its orbit. CARA has developed tables that can be used as decision aids to advise missions-in-development about the best way to utilize their differential drag capabilities. For missions below 560 km with the operational flexibility to devote multiple days to holding a high-drag configuration (or a sufficiently high drag ratio to compensate for limitations on that time), they are -- more likely than not -- able to successfully remediate high-risk conjunctions. Conversely, missions that do not meet these exacting criteria -- most missions -- can instead be advised to use on-board propulsion systems to perform RMMs, or to turn their minimum-area face towards the approach vector, thereby reducing Pc at the moment of conjunction due to the decreased Hard-Body Radius (HBR), that is a strongly correlated variable in the Pc calculations. (NASA, 2023)

conjunction assessment↗

NASA NTRS1993

Space Station Freedom advanced photovoltaics and battery technology development planning

Space Station Freedom (SSF) usable electrical power is planned to be built up incrementally during assembly phase to a peak of 75 kW end-of-life (EOL) shortly after Permanently Manned Capability (PMC) is achieved in 1999. This power will be provided by planar silicon (Si) arrays and nickel-hydrogen (NiH2) batteries. The need for power is expected to grow from 75 kW to as much as 150 kW EOL during the evolutionary phase of SSF, with initial increases beginning as early as 2002. Providing this additional power with current technology may not be as cost effective as using advanced technology arrays and batteries expected to develop prior to this evolutionary phase. A six-month study sponsored by NASA Langley Research Center and conducted by Boeing Defense and Space Group was initiated in Aug. 1991. The purpose of the study was to prepare technology development plans for cost effective advanced photovoltaic (PV) and battery technologies with application to SSF growth, SSF upgrade after its arrays and batteries reach the end of their design lives, and other low Earth orbit (LEO) platforms. Study scope was limited to information available in the literature, informal industry contacts, and key representatives from NASA and Boeing involved in PV and battery research and development. Ten battery and 32 PV technologies were examined and their performance estimated for SSF application. Promising technologies were identified based on performance and development risk. Rough order of magnitude cost estimates were prepared for development, fabrication, launch, and operation. Roadmaps were generated describing key issues and development paths for maturing these technologies with focus on SSF application.

Brender, Karen D.↗

NASA NTRS1998

Rare Potassium-Bearing Mica in Allan Hills 84001: Additional Constraints on Carbonate Formation

There have been presented several intriguing observations suggesting evidence of fossil life in martian orthopyroxenite ALH 84001. These exciting and controversial observations have stimulated extensive debate over the origin and history of ALH 84001, but many issues still remain unresolved. Among the most important is the question of the temperature at which the carbonates, which host the putative microfossils, formed. Oxygen- isotopic data, while showing that the carbonates are generally out of isotopic equilibria with the host rock, cannot constrain their temperature of formation. Both low- and high-temperature scenarios are plausible depending on whether carbonate growth occurred in an open or closed system. Petrographic arguments have generally been used to support a high-temperature origin but these appear to be suspect because they assume equilibrium between carbonate compositions that are not in contact. Some observations appear to be consistent with shock mobilization and growth from immiscible silicate-carbonate melts at high temperatures. Proponents of a low-temperature origin for the carbonates are hampered by the fact that there is currently no evidence of hydrous phases that would indicate low temperatures and the presence of a hydrous fluid during the formation of the carbonates. However, the absence of hydrous phases does not rule out carbonate formation at low temperatures, because the carbonate forming fluids may have been extremely CO2 rich, such that hydrous phases would not have been stabilized. In this study, I have carried out additional Transmission electron microscopy (TEM) studies of ALH-84001 and have found evidence of very rare phyllosilicates, which appear to be convincingly of pre-terrestrial origin. At present these observations are limited to one occurrence: further studies are in progress to determine if the phyllosilicates are more widespread.

Brearley, A. J.↗

NASA NTRS2017

NASA's Space Launch System: SmallSat Deployment to Deep Space

Leveraging the significant capability it offers for human exploration and flagship science missions, NASA's Space Launch System (SLS) also provides a unique opportunity for lower-cost deep-space science in the form of small-satellite secondary payloads. Current plans call for such opportunities to begin with the rocket's first flight; a launch of the vehicle's Block 1 configuration, capable of delivering 70 metric tons (t) to Low Earth Orbit (LEO), which will send the Orion crew vehicle around the moon and return it to Earth. On that flight, SLS will also deploy 13 CubeSat-class payloads to deep-space destinations. These secondary payloads will include not only NASA research, but also spacecraft from industry and international partners and academia. The payloads also represent a variety of disciplines including, but not limited to, studies of the moon, Earth, sun, and asteroids. While the SLS Program is making significant progress toward that first launch, preparations are already under way for the second, which will see the booster evolve to its more-capable Block 1B configuration, able to deliver 105t to LEO. That configuration will have the capability to carry large payloads co-manifested with the Orion spacecraft, or to utilize an 8.4-meter (m) fairing to carry payloads several times larger than are currently possible. The Block 1B vehicle will be the workhorse of the Proving Ground phase of NASA's deep-space exploration plans, developing and testing the systems and capabilities necessary for human missions into deep space and ultimately to Mars. Ultimately, the vehicle will evolve to its full Block 2 configuration, with a LEO capability of 130 metric tons. Both the Block 1B and Block 2 versions of the vehicle will be able to carry larger secondary payloads than the Block 1 configuration, creating even more opportunities for affordable scientific exploration of deep space. This paper will outline the progress being made toward flying smallsats on the first flight of SLS, and discuss future opportunities for smallsats on subsequent flights.

Robinson, Kimberly F.↗

NASA NTRS2017

NASA's Space Launch System: SmallSat Deployment to Deep Space

Leveraging the significant capability it offers for human exploration and flagship science missions, NASA's Space Launch System (SLS) also provides a unique opportunity for lower-cost deep-space science in the form of small-satellite secondary payloads. Current plans call for such opportunities to begin with the rocket's first flight; a launch of the vehicle's Block 1 configuration, capable of delivering 70 metric tons (t) to Low Earth Orbit (LEO), which will send the Orion crew vehicle around the moon and return it to Earth. On that flight, SLS will also deploy 13 CubeSat-class payloads to deep-space destinations. These secondary payloads will include not only NASA research, but also spacecraft from industry and international partners and academia. The payloads also represent a variety of disciplines including, but not limited to, studies of the moon, Earth, sun, and asteroids. While the SLS Program is making significant progress toward that first launch, preparations are already under way for the second, which will see the booster evolve to its more-capable Block 1B configuration, able to deliver 105t to LEO. That configuration will have the capability to carry large payloads co-manifested with the Orion spacecraft, or to utilize an 8.4-meter (m) fairing to carry payloads several times larger than are currently possible. The Block 1B vehicle will be the workhorse of the Proving Ground phase of NASA's deep-space exploration plans, developing and testing the systems and capabilities necessary for human missions into deep space and ultimately to Mars. Ultimately, the vehicle will evolve to its full Block 2 configuration, with a LEO capability of 130 metric tons. Both the Block 1B and Block 2 versions of the vehicle will be able to carry larger secondary payloads than the Block 1 configuration, creating even more opportunities for affordable scientific exploration of deep space. This paper will outline the progress being made toward flying smallsats on the first flight of SLS, and discuss future opportunities for smallsats on subsequent flights.

Robinson, Kimberly F.↗

NASA NTRS2016

Strategic Design of Long-Haul and Oceanic Aircraft Trajectories in Aviation Operations

Long-Haul Aircraft consume most of their fuel during the cruise phase of flight. The inefficiency in cruise flights compared to efficient routes varies is around 3 to 4. The efficiency of oceanic flights is low due to limited navigational and communication equipment, congestion and airspace restrictions. The availability of Automated Dependent Surveillance-Broadcast (ADS-B) and other improvements provides opportunity for better strategic planning of trajectories. Transatlantic flights between US and Europe constitute one of the busiest oceanic airspace regions in the world. This talk examines the benefits of a wind-optimal trajectory concept with a strategic de-confliction component compared to the current flight planning using the North Atlantic Tracks. The analysis is based on air traffic between US and Europe during July 2012. The potential fuel savings are in the range of (420-970) kg per flight for a Boeing 767-300, the most widely used aircraft between the city-pairs in this study. The talk also describes a global simulation of aviation operations combining flight plans and real air traffic data with historical commercial city-pair aircraft type and schedule data and global atmospheric data. The resulting capability extends the simulation and optimization functions of NASAs Future Air Traffic Management Concept Evaluation Tool (FACET) to global scale. This new capability is used to characterize the evolution of global air traffic, analyze fuel savings and seasonal variations in the long-haul wind-optimal traffic patterns in six major regions of the world.

strategic trajectory design↗

NASA NTRSDate not supplied

Integrated Design Results for the MSR SRC Mars Ascent Vehicle

The primary mission of the NASA Mars Sample Return (MSR) Campaign is to return samples of the Martian surface to Earth for scientific study. As part of this campaign, NASA is developing a Mars Ascent Vehicle (MAV). This vehicle must survive an approximate two year journey to the Martian surface as a payload aboard a separate lander spacecraft. After residing on the surface for another year, the MAV will carry a payload of samples into orbit. From there, following ejection from the MAV, the samples will rendezvous with an Earth return spacecraft for capture, and ultimately, return to Earth.The design of the MAV represents a number of unique challenges, as no launch vehicle has ever left the surface of a planet other than Earth. Although conceptual designs for a MAV have been in various levels of development since the 1970s, none have achieved the level of fidelity and support that exists in the current MSR-MAV design. Early MSR-MAV concept studies examined multiple methods of propulsion, ultimately deciding that a Two Stage to Orbit (TSTO) solid propulsion vehicle would provide the most capable performance in a Martian environment. Following this key architecture decision, the vehicle design was further matured to a Solid-Solid Guided-Guided (SSGG) architecture for NASA Key Decision Point A (KDP-A). Although the SSGG design was able to meet all mission constraints, concerns were raised regarding limited mass margin on other elements of the MSR campaign at such an early phase. A design challenge was issued to reduce MAV total mass by as much as possible. It was ultimately determined that by moving a number of components of the vehicle second stage to the first stage, the overall vehicle mass could be reduced significantly. The new design featured a much smaller and completely unguided second stage. This paper describes the resultant Solid-Solid Guided-Unguided (SSGU) MAV design concept developed as part of the Systems Requirement Cycle (SRC). This design was developed primarily by NASA Marshall Space Flight Center (MSFC), in association with NASA Jet Propulsion Laboratory (JPL) and NASA Langley Research Center (LaRC). The TSTO vehicle includes one solid rocket motor per stage. As the vehicle second stage is unguided, it features spin-stabilization to maintain vehicle stability during flight. An electromechanically actuated Thrust Vector Control (TVC) and a monopropellant Reaction Control System (RCS) is employed for active guidance on the first stage. The vehicle is designed to deliver up to 0.47kg of Martian samples to a Mars circular orbit of 380km at 27° inclination. Due to the extremely unique design constraints of this mission, and a recent transition to a Risk Class A posture, the MAV team was compelled to devise unconventional solutions to the vehicle design. The detailed design and analysis of these subsystems and the vehicle as a whole are discussed in this paper relative to all of the engineering disciplines involved.

MSR↗

NASA NTRS2006

When Will the Antarctic Ozone Hole Recover?

The Antarctic ozone hole develops each year and culminates by early spring (late September - early October). Antarctic ozone values have been monitored since 1979 using satellite observations from the TOMS instrument. The severity of the hole has been assessed from TOMS using the minimum total ozone value from the October monthly mean (depth of the hole) and by calculating the average area coverage during this September-October period. Ozone is mainly destroyed by halogen (chlorine and bromine) catalytic cycles, and these losses are modulated by temperature variations in the collar of the polar lower stratospheric vortex. In this talk, I will show the relationships of halogens and temperature to both the size and depth of the hole. Because atmospheric halogen levels are responding to international agreements that limit or phase out production, the amount of halogens in the stratosphere should decrease over the next few decades. Using projections of halogen levels combined with age-of-air estimates, we find that the ozone hole is recovering at an extremely slow rate and that large ozone holes will regularly recur over the next 2 decades. The ozone hole will begin to show first signs of recovery in about 2023, and the hole will fully recover to pre-1980 levels in approximately 2070. This 2070 recovery is 20 years later than recent projections. I will also discuss current assessments of mid-latitude ozone recovery.

Newman, Paul A.↗