SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Styrylpyridine and its derivatives are studied. The synthesis, characterization, and thermal stability of styrylpyridine based polymers are discussed, as well as the preparation of a diglycidyl ester of styrylpridine. Also discussed are the preparation of polyarylates, and styrylpyridine based polytriazines and prepolymers.
The characteristics of carbon fibers (CF) made from polyacrylonitrile (PAN) materials are discussed, together with research on conducting polymers. CF materials have better mechanical properties, chemical inertness, and higher stiffness than metallic materials but are subject to environmental instability, flammability, and delamination fatigue. Polymerization procedures for the monopolymer PAN are described, noting the use of SEM and X-ray diffraction techniques for studying the fiber structure. High modulus and strength of CF are caused by covalent sp(2) bonds in hexagonal carbon rings, which are stronger than the same links in diamonds. Details of the molecular chain structures and macroformations, stress-strain as a function of temperature, and thermosetting and glass transition temperatures of polymers are provided. Computational quantum chemistry techniques are being applied to studying electrical conductance in polymers, mainly to discover ways to stabilize the materials. Doped CH(x) has exhibited photovoltaic properties and other polymers have become superconductors at cryogenic temperatures.
A carbon monoxide (CO) sensor was developed that can be incorporated into an existing sensing array architecture. The CO sensor is a low-power chemiresistor that operates at room temperature, and the sensor fabrication techniques are compatible with ceramic substrates. Sensors made from four different polymers were tested: poly (4-vinylpryridine), ethylene-propylene-diene-terpolymer, polyepichlorohydrin, and polyethylene oxide (PEO). The carbon black used for the composite films was Black Pearls 2000, a furnace black made by the Cabot Corporation. Polymers and carbon black were used as received. In fact, only two of these sensors showed a good response to CO. The poly (4-vinylpryridine) sensor is noisy, but it does respond to the CO above 200 ppm. The polyepichlorohydrin sensor is less noisy and shows good response down to 100 ppm.
Through-the-thickness stitching can be used to provide a pathway to reduce interlaminar damage in laminated polymer composites. To decrease the amount of stitching, a selective stitching process is necessary to reduce the total manufacturing time in stitched polymer composites. In this study, L-shaped laminates are stitched in the radius section to arrest out-of-plane damage that can occur when subjected to four-point bending loads. A cohesive zone finite element model of the L-shaped laminate was developed. An embedded spring element approach was used to represent the through-the-thickness reinforcements within the finite element model. Specimens with stitches in the radius region of the L-shaped laminate were found to have greater maximum loads before failure. The through-the-thickness stitches are observed to locally reduce the radial stresses in the radius region of the L-shaped laminate, which results in delamination growth away from the radius centerline and greater load-carrying capability.
Abstract Glass fiber‐reinforced polymer composites are widely used in marine applications, including renewable energy devices and submarines, due to their strength‐to‐weight ratios and corrosion resistance. As sustainability becomes more important, recyclable thermoplastic composites are gaining attention in marine energy applications. These materials face harsh conditions such as high chloride water, UV radiation, pressurization, and thermal cycling, which can affect their durability and recyclability. This study examines the impact of hygrothermal aging on the recyclability of an Elium glass fiber (GF) composite. Samples were mechanically ground for recycling, and mechanical and thermal properties were compared between aged and unaged samples. After seawater aging, the tensile strength and modulus of the unaged composite dropped by 25% and 13% respectively, due to water ingress along the fiber‐matrix interface. The recycled composite showed reduced flexural strength as the long fiber composite was converted into short fibers during the process. Differential scanning calorimetry (DSC) revealed no change in glass transition temperature after aging. Weight loss (25%) was attributed to the thermal stability of the glass fibers. Dynamic mechanical analysis (DMA) showed that the storage modulus increased with aging, and fracture analysis confirmed a mixed mode of failure for aged composites. Highlights Hygrothermal aging lowers mechanical performance of Elium® GF composites. Failure mechanism tends to be matrix cracking and interface bonding. Glass transition temperature is not reduced by hygrothermal aging. Fractured composite was successfully recycled via thermoforming. Flexural strength of the recycled composite is lower.
The development of polymer composite liquid oxygen LO2 tanks is a critical step in creating the next generation of launch vehicles. Future launch vehicles need to minimize the gross liftoff weight (GLOW), which is possible due to the 25%-40% reduction in weight that composite materials could provide over current aluminum technology. Although a composite LO2 tank makes these weight savings feasible, composite materials have not historically been viewed as "LO2 compatible." To be considered LO2 compatible, materials must be selected that will resist any type of detrimental, combustible reaction when exposed to usage environments. This is traditionally evaluated using a standard set of tests. However, materials that do not pass the standard tests can be shown to be safe for a particular application. This paper documents the approach and results of a joint NASA/Lockheed Martin program to select and verify LO2 compatible composite materials for liquid oxygen fuel tanks. The test approach developed included tests such as mechanical impact, particle impact, puncture, electrostatic discharge, friction, and pyrotechnic shock. These tests showed that composite liquid oxygen tanks are indeed feasible for future launch vehicles.
The application of fiber composites to aeronautical and space vehicle systems indicates the following: It appears quite probable that resin/fiber composites can be developed for service at 315 C for several thousand hours and at 370 C for a few hundred hours. The retention of resin/fiber strength at these high temperatures can be achieved by modifying the polymer molecular structure or by developing new processing techniques, or both. Carbon monofilament with attractive strength values has been produced and fabrication studies to reinforce aluminum with such monofilaments have been initiated. Refractory wire-superalloy composites have demonstrated sufficiently high strength and impact values to suggest that they have potential for application to turbine blades at temperatures to 1200 C and above.
Research directed toward the application of fiber composites to aeronautical and space vehicle systems indicates that resin/fiber composites can be developed for service at 315 C for several thousand hours and at 370 C for a few hundred hours. The retention of resin/fiber strength at these high temperatures can be achieved by modifying the polymer molecular structure or by developing new processing techniques, or both. Carbon monofilament with attractive strength values has been produced and fabrication studies to reinforce aluminum with such monofilaments have been initiated. Refractory wire-superalloy composites have demonstrated sufficiently high strength and impact values to suggest that they have potential for application to turbine blades at temperatures to 1200 C and above.
The objective of this work was to increase the interfacial strength between aramid fiber and epoxy matrix. This was achieved by functionalizing the aramid fiber followed by growth of a layer of ZnO nanowires on the fiber surface such that when embedded into the polymer, the load transfer and bonding area could be substantially enhanced. The functionalization procedure developed here created functional carboxylic acid surface groups that chemically interact with the ZnO and thus greatly enhance the strength of the interface between the fiber and the ZnO.
System needs and challenges for commercial aviation and space exploration are constantly changing. Multifunctional materials are ideal for aerospace applications because their integration into structural components has potential to not only improve efficiency, but it can also increase payload and mission capabilities without the burden of significant additions to mass and volume. Multi-constituent materials will play an important role in enabling structures with the potential to demonstrate true multi-functionality; however, modifications to many mature polymer processing methods may be necessary. This presentation will cover multifunctional materials development efforts underway at the NASA Glenn Research Center related to formulating and characterizing novel electrical insulation for high voltage aircraft. Incorporating functionality into the reinforcement material is another materials development technique that will be discussed, which includes braiding with hybrid fibers to enhance toughness in composite structures, stitching with carbon nanotube yarns to make durable electrically conductive textiles, and treating fabrics with shear thickening fluid suspensions to produce impact-resistant inflatable habitats.
The electrochemical, bulk and interfacial properties of the polyethylene oxide (PEO) based composite solid electrolyte (CSE) comprising LiI, PEO, and Al2O3 have been evaluated for Li battery applications. The bulk interfacial and transport properties of the CSEs seem to strongly depend on the alumina particle size. For the CSE films with 0.05 micron alumina while the bulk conductivity is around 10(exp -4) (mho/cm) at 103 C, the Li ion transport number seems to be close to unity at the same temperature. Compared to the PEO electrolyte this polymer composite electrolyte seems to exhibit robust mechanical and interfacial properties. We have studied three different films with three different alumina sizes in the range 0.01-0.3 micron. Effects of Al2O3 particle size on the electrochemical performance of polymer composite electrolyte is discussed. With TiS2 as cathode a 10 mAh small capacity cell was charged and discharged at C/40 and C/20 rates respectively.
The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimides - Ultem 9085 and experimental Ultem 1000 mixed with 10 percent chopped carbon fiber. A property comparison between FDM-printed and injection-molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25-31 percent. Coupons of Ultem 9085 and experimental Ultem 1000 composites were tested at room temperature and 400 degrees Fahrenheit to evaluate their corresponding mechanical properties.
This memo includes the documentation sections for the Library of Advanced Materials for Engineering (LAMÉ) manual for a fiber reinforced polymer composite damage model (Elastic_Orthotropic_FRP_Modular_Damage) in advance of the next Sierra/SM and LAMÉ release consistent with the transition of the model from development to a production capability. This new model capability provides both a set of physically based orthotropic damage criteria as well as orthotropic material softening for woven fiber reinforced polymer composite materials. The documentation sections include short sections on theory, implementation, verification, and user guidance to prescribe the model in a Sierra/SM input file.
The objective of this project was to conduct additive manufacturing to produce aircraft engine components by Fused Deposition Modeling (FDM), using commercially available polyetherimdes Ultem 9085 and experimental Ultem 1000 filled with 10 chopped carbon fiber. A property comparison between FDM-printed and injection molded coupons for Ultem 9085, Ultem 1000 resin and the fiber-filled composite Ultem 1000 was carried out. Furthermore, an acoustic liner was printed from Ultem 9085 simulating conventional honeycomb structured liners and tested in a wind tunnel. Composite compressor inlet guide vanes were also printed using fiber-filled Ultem 1000 filaments and tested in a cascade rig. The fiber-filled Ultem 1000 filaments and composite vanes were characterized by scanning electron microscope (SEM) and acid digestion to determine the porosity of FDM-printed articles which ranged from 25-31. Coupons of Ultem 9085, experimental Ultem 1000 composites and XH6050 resin were tested at room temperature and 400F to evaluate their corresponding mechanical properties.
This program supported investigation of an all-polymer percolative composite which exhibits very high dielectric constant (less than 7,000). The experimental results show that the dielectric behavior of this new class of percolative composites follows the prediction of the percolation theory and the analysis of the conductive percolation phenomena. The very high dielectric constant of the all-polymer composites which are also very flexible and possess elastic modulus not very much different from that of the insulation polymer matrix makes it possible to induce a high electromechanical response under a much reduced electric field (a strain of 2.65% with an elastic energy density of 0.18 J/cu cm can be achieved under a field of 16 MV/m). Data analysis also suggests that in these composites, the non-uniform local field distribution as well as interface effects can significantly enhance the strain responses. Furthermore, the experimental data as well as the data analysis indicate that the conduction loss in these composites will not affect the strain hysteresis.
Polysaccharides, including chitin, are one of the most abundant biopolymers in nature and are increasingly recognized as a sustainable alternative to petroleum-derived plastics and synthetic fillers in polymer composites. Traditionally sourced from crustacean shells, chitin offers mechanical strength and biocompatibility with limitations also in processability and functionality. Fungal-derived chitin material represents a promising alternative, with advantages including scalable fermentation on low-cost substrates, absence of shellfish allergens, and tunable molecular architectures that vary by species, developmental stage, and growth environment. Here, in this study, we systematically examined chitinous materials obtained from taxonomically and functionally distinct fungi, Laccaria bicolor, Trichoderma reesei and Rhizopus oryzae, to assess their structural, chemical, and morphological properties as reinforcement agents in polymer composites. Mild alkaline pretreatment was employed to obtain mycelium chitin particles, thereby improving accessibility to chitin and co-occurring β-D-glucans while maintaining microparticle integrity. Comprehensive FTIR and solid-state NMR analyses revealed species-specific differences in chemical composition and microstructure, with R. oryzae exhibiting a unique spectral signature. These fungal-derived chitin were then incorporated into poly(vinyl alcohol) (PVA) hydrogels, where they acted as reinforcing fillers without the need for additional chemical crosslinkers. Comparative evaluation of hydrogel properties demonstrated that fungal chitin significantly enhanced mechanical performance, with all mycelium fillers mitigating the water weakening in PVA hydrogels. R. oryzae-derived composites tripled the hydrogel tensile strength while the submicron fibrous morphology in L. bicolor contributes to over 45 % tensile improvement in dry PVA composites. Our findings highlight the potential of fungal biomass as a tunable, sustainable platform for producing chitin-based reinforcing agents.
Aircraft noise reduction is an application of current intense interest for which smart materials show significant potential. Specifically, the aeroacoustic noise produced by the unsteady aerodynamic flow about the leading-edge high-lift device, such as leading-edge slat, of typical transport-aircraft wings is of particular interest. Concepts with the most promise to mitigate this noise source, most notably the slat-cove filler concept, have focused on highly reconfigurable structures that change shape between different phases of the flight envelope. These shape changes often involve large deformation, which has stimulated the consideration of shape memory materials. In recent years, shape memory materials (SMMs) have drawn greater interest for applications such as smart fabrics, intelligent medical devices, self-deployable space structures, morphing structures and packaging. Compared to other shape memory materials, like shape memory alloys (SMAs) or shape memory ceramics (SMCs), shape memory polymers (SMPs) have desirable advantages such as high elastic deformation to enable large shape change, broad tailorability of mechanical properties, potential biocompatibility and biodegradability, ductility, light weight and ease of processing. However, SMPs still have some critical disadvantages such as insufficient mechanical and thermal characteristics for structural applications, low recovery stress, and long response time. The new LaRC shape memory thermosetting polymer composite (LaRC-SMPC) discussed herein was synthesized with nontoxic monomers and conductive/magnetic fillers to yield enhanced thermal/mechanical characteristics and faster response times. LaRC-SMPCs with a variety of fiber reinforcements [Kevlar®, carbon fiber (standard and thin-ply), and carbon-nanotube (CNT) sheet] were fabricated to tailor the physical properties and test for suitability as a slat-cove filler (SCF). The performance of SCF prototypes fabricated with the developed LaRC-SMPCs was evaluated using a bench-top test apparatus. The SCFs made of Kevlar® fiber fabric or carbon fiber fabric infused shape memory polymer composite (SMPC) exhibited kinking during simulated deployment and stowage, which can be problematic during operation. The SCF made of CNT sheet/SMP composite did not exhibit kinking, but the deployment was sluggish compared to carbon fiber fabric/SMP composite. This report documents the evolution of designing SMPCs as slat-cove fillers for aircraft noise reduction. In the course of the investigation, several 2 approaches were investigated to address shortcomings in material characteristics based on performance requirements of operational slat-cove fillers.
Filled polymer compositions are made by dissolving the polymer binder in a suitable sublimable solvent, mixing the filler material with the polymer and its solvent, freezing the resultant mixture, and subliming the frozen solvent from the mixture from which it is then removed. The remaining composition is suitable for conventional processing such as compression molding or extruding. A particular feature of the method of manufacture is pouring the mixed solution slowly in a continuous stream into a cryogenic bath wherein frozen particles of the mixture result. The frozen individual particles are then subjected to the sublimation.