Search NASA⌕ Search

SEARCH · Search NASA

Results for “recombination layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Ion-neutral coupling in the high-latitude F region Evaluation of ion heating terms from Dynamics Explorer 2

Ion and neutral motions in the high latitude F layer were studied simultaneously during six passes of the Dynamics Explorer 2 spacecraft. The passes were made over the south polar cap in October 1981. An ion energy balance equation was defined to express the exchange of energy between the F layer and other atmospheric constituents. A momentum equation expressed the momentum exchange between the species. An approximate form of the energy balance equation was also formulated. The time constant for ion-neutral collisional momentum transfer significantly affected Joule heating in the F layer. Regions of large velocity disparities and ion temperature enhancements were detected as hot spots. The results indicate that a feedback mechanism may arise in terms of neutral compositional changes and enhanced ionospheric recombination. The approximate equation furnished values for ion heating rates which matched the data.

Killeen, T. L.↗
DOE OSTI2025

Uncooled GeSn MWIR Photodetectors Using Fully Relaxed Thin Triple‐Step Buffer

GeSn photodetectors monolithically grown on Ge virtual substrates demonstrate mid-wave infrared (MWIR) detection at room temperature. The lattice mismatch between GeSn and Ge causes dislocations and compressive strain, creating leakage pathways and unwanted indirect band transitions. Designed thin Ge 0.91 Sn 0.09 triple-step buffer layers of ≈175 nm total thickness reduce dislocations and enable full relaxation, showing 100% lattice relaxation and smooth surface roughness of 0.83 nm with shorter auto-correlation length in surface morphology compared to single-step buffers. Ge 1-x Sn x photodetectors (x = 0.09, 0.12, and 0.15) on triple-step buffers with n-i-p configurations achieve lattice strain relaxations of 99%, 88%, and 80%, respectively. Ge 0.91 Sn 0.09 and Ge 0.88 Sn 0.12 show gradual variation in auto-correlation amplitude, while Ge 0.85 Sn 0.15 shows an increase due to lattice mismatch. Shockley–Read–Hall recombination current dominates at low reverse bias due to mismatch-induced dislocations, while band-to-band tunneling current dominates at higher reverse bias due to narrowing bandgap under strong electric fields. Here, the photodetectors show extended spectral response with increasing Sn composition of i-GeSn active layer sandwiched by barriers. Ge 0.88 Sn 0.12 and Ge 0.85 Sn 0.15 exhibit extended wavelength cut-offs of 3.12 and 3.27 µm at room temperature, demonstrating significant potential for silicon-based MWIR applications.

GeSn↗
DOE OSTI2020

Continuous polymer films deposited on top of porous substrates using plasma-enhanced atomic layer deposition and molecular layer deposition

Molecular layer deposition (MLD) is able to produce ultrathin polymer films with control over thickness, cross-linking, and chemical composition. With these capabilities, MLD should be useful in the fabrication of novel polymer membranes on porous supports. However, confining a continuous MLD film to the surface of porous substrates is difficult because of MLD film growth in the pores. The deposition in the pores lowers the conductance of the porous support. This paper presents a method to deposit continuous polymer films on top of porous substrates. In this method, Al2O3 plasma-enhanced atomic layer deposition (PE-ALD) using trimethylaluminum and oxygen plasma as the reactants was first used to cap the pores of the substrate. Subsequently, a polyamide MLD film was deposited on the Al2O3 PE-ALD capping layer using m-phenylenediamine and trimesoyl chloride as the reactants. The Al2O3 pore caps were then removed from the porous substrate by etching from the backside using a timed exposure to a dilute sodium hydroxide solution. This method was demonstrated using anodic aluminum oxide (AAO) and polyethersulfone (PES) porous substrates. Al2O3 PE-ALD film growth was limited to the top of the porous substrate, resulting in rapid surface recombination or high sticking coefficients for the reactive plasma species within the pores. Gas permeance measurements confirmed the pore capping of the AAO substrates. The reopening of the pores by dissolving the Al2O3 pore caps with a sodium hydroxide solution was monitored using gas permeance versus etch time. The removal of the Al2O3 pore caps from the PES substrates could also dissolve the Al2O3 layer underneath the MLD film. The loss of this Al2O3 layer led to the detachment of the MLD film from the PES substrate. However, the MLD film could be anchored to the PES support at fractures located in the Al2O3 film prior to the MLD. The Al2O3 film fracture allowed the MLD film to anchor firmly to the PES substrate by MLD in the pores of the PES porous substrate. The distance between the anchor points was a function of fracture density. This distance could be controlled by applying a tensile stress to the Al2O3 PE-ALD film to fracture the film through sample bending. This method produced firmly anchored polymer MLD films on top of the PES porous substrates.

Welch, Brian C. (ORCID:000000029747045X)↗
DOE OSTI2020

Design, Optimization, and In-Depth Understanding of Front and Rear Junction Screen-Printed Double-Side Passivated Contacts Solar Cells

In this work, detailed numerical modeling is performed for front junction (FJ) and rear junction (RJ) n-type Si solar cells with screen-printed double-side poly-Si based tunnel oxide passivated contacts (TOPCon). Fundamental understanding of both structures is crucial to explore factors that limit the efficiency potential of the two designs. By investigating several key parameters such as front poly sheet resistance and thickness, bulk material properties, and carrier transport in our simulation model, we determine and explain why RJ cells outperform FJ cells. Our findings reveal that FJ suffers from present technological limitations of p-poly based passivated contacts, namely, i) large recombination observed in textured p-TOPCon emitter and ii) low solid solubility and hole mobility in boron-doped poly-Si resulting in very high sheet resistance of front p-poly layers which must be made thin to reduce absorption losses. In contrast, RJ desensitized the cell efficiency to front sheet resistance allowing application of ultra-thin front n-poly layers and is therefore ideally suited for double-side TOPCon cells. Lastly, we have developed a roadmap for efficiency projections of commercial-type screen-printed RJ and FJ topologies reaching ~24% and >22.5% efficiencies respectively, quantifying and explaining the impact of technological innovations on the performance of each design.

14 SOLAR ENERGY↗
NASA NTRS1976

Theoretical analysis of Al/x/Ga/1-x/As-GaAs graded band-gap solar cell

A practical theoretical analysis of an n/p graded band-gap Al(x)Ga(1-x)As-GaAs solar cell indicates that the presence of a built-in electric field acting on holes in the surface layer increases the hole collection efficiency of a nearly optimum cell to a maximum of 97.8%. The electric field is created by the band-gap gradient and serves to reduce the surface hole recombination by 97% and reduce the bulk hole recombination by 80%, compared to a similar GaAs cell. These reduced losses increase cell response substantially for wavelengths less than 0.59 micron and yield a maximum air-mass-zero efficiency of 17.7% (not corrected for a 13% front-surface contact). The model includes an optimized antireflection coating, series resistance, and junction-recombination current.

Hutchby, J. A.↗
NASA NTRS1993

Stagnation flowfield analysis for an aeroassisted vehicle

Hypersonic reactive flowfield results are presented for the flow about an axisymmetric representation of a three-dimensional aeroassisted vehicle using the viscous shock-layer (VSL) and Navier-Stokes (NS) equations for low- and high-altitude entry conditions, respectively. Solutions are limited to the stagnation region. The NS results have been obtained by employing the surface recombination boundary condition for an 11-species air model, whereas the VSL calculations are carried out by using a 5-species model. Three widely used surface recombination rate models are implemented with these two flowfield calculation procedures. The low-density (or high altitude) NS solutions are obtained with surface slip equations and compare quite well with the direct simulation Monte Carlo predictions. For higher densities (or lower altitudes), the no-slip VSL solutions are considered adequate. Results from this study highlight the effect of surface catalyticity on surface heating and electron number density.

Gupta, Roop N.↗
DOE OSTI2022

Tuning Intermediate Bands of Protective Coatings to Reach the Bulk-Recombination Limit of Stable Water-Oxidation GaP Photoanodes

Stable photoelectrochemical solar fuel production requires protective coatings to achieve effective charge separation, transport, and injection at the semiconductor–liquid interfaces, implying that the coating should energetically align its intermediate band (IB) with both the photoabsorber's band edge and co-catalyst's potentials. Yet approaches to adjust coating IB positions to accommodate various semiconductor light absorbers for constructing efficient and stable photoelectrodes have not been developed. In this report, three types of transition metal (M = Mn 2+ , Mn 3+ , and Cr 3+ ions) alloyed TiO2 coatings are discovered using atomic layer deposition (ALD). The IB energetics of these coatings are characterized by X-ray photoelectron spectroscopy and are found to be tunable inside the TiO 2 bandgap, through varying ALD growth conditions. By applying these coatings to n-type GaP and integrating with IrO x co-catalysts, the water-oxidation J–E performance is comparable to an uncoated corroding GaP photoanode. It reaches the bulk recombination limit of the GaP and achieves ≈28% absorbed photon to current efficiency under 475-nm light excitation (6.48 mW cm -2 ) and 100-h stable water oxidation. The outstanding performance and stability are attributed to the efficient charge separation and hole transport, as allowed by the energy alignment of the coating IB and the GaP valence band edge.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sputter-Coated TiO 2 Films as Passivation and Hole Transfer Layers for Improved Energy Conversion with Solar Fuel WO 3 /CuWO 4 Photoanodes

Atomic layer deposited (ALD) “leaky” TiO 2 have gained interest as charge-selective protection layers for semiconductor solar fuel electrodes. Here we demonstrate the use of sputter-deposited TiO 2 layers as hole selective contacts for WO 3 /CuWO 4 type 2 heterojunction water oxidation photoanodes for the first time. TiO 2 protection layers with varying thicknesses (2 to 128 nm) were deposited using the RF magnetron sputtering technique. The resulting TiO 2 films are amorphous based on Raman spectroscopy and powder XRD. Photoelectrochemical scans and Vibrating Kelvin probe photovoltage spectroscopy show that 2-8 nm TiO 2 layers nearly double the photocurrent to 0.97 mA cm -2 under AM 1.5 illumination (19% AQE at 350 nm), increase the surface photovoltage signal by 25%, and increase the WO 3 /CuWO 4 bandgap. These effects can be attributed to the selectivity of TiO 2 for photoholes. Additionally, SPV data suggest that TiO 2 overlayers suppress copper-based surface recombination defects. Reduced photocurrent and the photovoltage are seen in thicker TiO 2 films (16 to 128 nm) as a result of an increasing hole transfer resistance and because of light shading effects according to photoaction spectra. The TiO 2 films also improve the stability of the WO 3 /CuWO 4 photoelectrodes, allowing nearly constant O 2 evolution over 3 hours after an initial 20-35% loss. Overall, this work establishes RF magnetron sputtering as a useful method to install amorphous TiO 2 passivation layers for improved WO 3 /CuWO 4 solar fuel photoelectrodes. Furthermore, we show how the combination of PEC with SPV measurements provides insight into the function of the TiO 2 coatings.

CuWO4↗
DOE OSTI2022

Structural and optical properties of cubic GaN on U-grooved Si (100)

Cubic GaN epitaxy on large-area U-grooved silicon (100) dies is demonstrated by metalorganic chemical vapor deposition, and its structural and optical properties are reported. Scanning electron, atomic force, and transmission electron microscopy studies reveal that cubic GaN shows no discernible threading dislocations and a low stacking fault density of 3.27 ± 0.18 × 10 4 cm –1 . Temperature-dependent photoluminescence studies reveal as-grown cubic GaN band edge emission internal quantum efficiency as 25.6% ± 0.9%. Selective etching of the low-temperature AlN buffer layer, SiO 2 sidewalls, and hexagonal-phase GaN is demonstrated, which increases the cubic GaN band edge emission internal quantum efficiency to 31.6% ± 0.8%. This increase is attributed to the decrease in the radiative recombination lifetime via the removal of defective hexagonal-phase GaN. Altogether, cubic GaN on U-grooved silicon with high structural and optical quality is reported, promising its suitability for next-generation devices.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Thermally-restorable optical degradation and the mechanism of current transport in Cu2S-CdS photovoltaic cells

The photovoltaic properties of single-crystal Cu2S-CdS heterojunctions have been investigated as a function of heat treatment by detailed measurements of the dependence of short-circuit current on photon energy, temperature, and the state of optical degradation or enhancement. A coherent picture is formulated for the relationship between enhancement and optical degradation, and their effect on the transport of short-circuit photoexcited current and dark, forward-bias current in the cell. Optical degradation in the Cu2S-CdS cell is shown to be closely identical to optical degradation of lifetime in a homogeneous CdS:Cd:Cu crystal, indicating that the CdS:Cu layer near the junction interface controls carrier transport in the cell. It is proposed that both the photoexcited short-circuit current and the dark, forward-bias current are controlled by a tunneling-recombination process through interface states.

Fahrenbruch, A. L.↗
NASA NTRS1984

Effect of reabsorbed recombination radiation on the saturation current of direct gap p-n junctions

The application of the radiative transfer theory for semiconductors to p-n homojunctions subject to low level injection conditions is discussed. By virtue of the interaction of the radiation field with free carriers across the depletion layer, the saturation current density in Shockley's expression for the diode current is reduced at high doping levels. The reduction, due to self-induced photon generation, is noticeable for n-type material owing to the small electron effective mass in direct band-gap III-V compounds. The effect is insignificant in p-type material. At an equilibrium electron concentration of 2 x 10 to the 18th/cu cm in GaAs, a reduction of the saturation current density by 15 percent is predicted. It is concluded that realistic GaAs p-n junctions possess a finite thickness.

Von Roos, O.↗
NASA NTRS1985

The unexpected ultraviolet variability of Herbig-Haro object 1

The line fluxes of the C IV 1550 A and semiforbidden C III 1909 A emission lines in HH 1 are noted to have monotonically decreased by factors of 4-6 between 1979 and 1983, despite a lack of indications of optical range changes. The thickness of the shocked layers and preshock density can be estimated on the basis of these rapid changes, with results suggesting a clumpy medium that leads to truncated shock waves with column densities insufficient for the development of complete recombination zones.

Brugel, E. W.↗
NASA NTRS2012

High Enthalpy Studies of Capsule Heating in an Expansion Tunnel Facility

Measurements were made on an Orion heat shield model to demonstrate the capability of the new LENS-XX expansion tunnel facility to make high quality measurements of heat transfer distributions at flow velocities from 3 km/s (h(sub 0) = 5 MJ/kg) to 8.4 km/s (h(sub 0) = 36 MJ/kg). Thirty-nine heat transfer gauges, including both thin-film and thermocouple instruments, as well as four pressure gauges, and high-speed Schlieren were used to assess the aerothermal environment on the capsule heat shield. Only results from laminar boundary layer runs are reported. A major finding of this test series is that the high enthalpy, low-density flows displayed surface heating behavior that is observed to be consistent with some finite-rate recombination process occurring on the surface of the model. It is too early to speculate on the nature of the mechanism, but the response of the gages on the surface seems generally repeatable and consistent for a range of conditions. This result is an important milestone in developing and proving a capability to make measurements in a ground test environment and extrapolate them to flight for conditions with extreme non-equilibrium effects. Additionally, no significant, isolated stagnation point augmentation ("bump") was observed in the tests in this facility. Cases at higher Reynolds number seemed to show the greatest amount of overall increase in heating on the windward side of the model, which may in part be due to small-scale particulate.

Dufrene, Aaron↗
DOE OSTI2020

The significance of the local structure of cobalt-based catalysts on the photoelectrochemical water oxidation activity of BiVO 4

The local structures of the water oxidation catalysts play an important role in reaction kinetics and the performance of the photoanodes. In this study, we deposited cobalt-based catalysts on nanoporous BiVO 4 with controlled thicknesses by atomic layer deposition (ALD). Despite the similar oxidation states of cobalt in all depositions, different water oxidation activities in neutral pH conditions were observed. Here, a dramatic photocurrent raise, lowered kinetic overpotential, and smaller charge transfer resistance across the photoanode/electrolyte interface were achieved when a uniform ultrathin Co(OH) 2 layer was formed on BiVO 4 . Photocurrent density for water oxidation showed a 95% enhancement at 0.6 V vs. RHE when the catalyst was in the form of Co(OH) 2 , while an 80% increase was obtained for CoO. Ideal coordination of Co(OH) 2 on hydroxylated BiVO 4 surface assists the charge transfer between the electrolyte and BiVO 4 without increasing surface recombination. The results of this study emphasize the importance of controlling the local structure of the catalysts in the performance of the water splitting photoanodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Enabling bifacial thin film devices by developing a back surface field using Cu x AlO y

Bifacial solar cells have the potential to increase the energy yield per unit area over traditional monofacial devices without significant added cost, driving $/kWh costs lower and accelerating the adoption of solar photovoltaics. However, the performance of bifacial thin film solar cells significantly lags that achieved by crystalline silicon cells. Here we incorporate wide bandgap Cu x AlO y as a back buffer layer for CdTe devices and achieve a backside illuminated device with high current density and high fill factor. Moreover, these values remain nearly constant even as the absorber layer thickness changes, indicating that a fully-depleted device is not required for efficient charge collection. We show that this response is indicative of a back surface field, albeit with a persistent high back surface recombination velocity. By managing electron reflection, we achieved a backside illumination conversion efficiency of 7.1% and bifaciality of 0.55 for a 3.3 µm CdTe device and 8.0% and 0.62 for a 2 µm device. Future improvements can be made by identifying and incorporating a passivation material that reduces the back surface recombination velocity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxygen Management to Avoid Photo-Inactive Cd(S,Se) for Efficient Cd(Se,Te) Solar Cells

Our previous work has demonstrated that the formation of a penternary cadmium chalcogenide Cd(O,S,Se,Te) region can significantly reduce the front interface recombination in Cd(Se,Te)-based thin-film solar cells. In this work, we have shown that oxygen management during the device fabrication is crucial to form this region. While both the CdS and CdSe layer depositions and the postdeposition CdCl2 treatment should be conducted in the presence of oxygen, the CdTe deposition should be conducted in an oxygen-free atmosphere. Improper oxygen management leads to low device performance due to the formation of a photoinactive Cd(S,Se) region and reduced absorber quality. Additionally, we investigated the carrier transport and collection properties in devices with photoinactive Cd(S,Se) and photoactive Cd(O,S,Se,Te) at the front interface to gain comprehensive understanding of the mechanisms that resulted in improved efficiencies approaching 20%.

CdTe deposition↗
NASA NTRS1990

Estimation of minority carrier diffusion lengths in InP/GaAs solar cells

Minority carrier diffusion length is one of the most important parameters affecting the solar cell performance. An attempt is made to estimate the minority carrier diffusion lengths is the emitter and base of InP/GaAs heteroepitaxial solar cells. The PC-1D computer model was used to simulate the experimental cell results measured at NASA Lewis under AMO (air mass zero) spectrum at 25 C. A 16 nm hole diffusion length in the emitter and a 0.42 micron electron diffusion length in the base gave very good agreement with the I-V curve. The effect of varying minority carrier diffusion lengths on cell short current, open circuit voltage, and efficiency was studied. It is also observed that the front surface recombination velocity has very little influence on the cell performance. The poor output of heteroepitaxial cells is caused primarily by the large number of dislocations generated at the interfaces that propagate through the bulk indium phosphide layers. Cell efficiency as a function of dislocation density was calculated and the effect of improved emitter bulk properties on cell efficiency is presented. It is found that cells with over 16 percent efficiencies should be possible, provided the dislocation density is below 10(exp 6)/sq cm.

Jain, R. K.↗
DOE OSTI2021

Colossal Grains for a New Structural Paradigm in Thin-Film Photovoltaics

II-VI based thin-film photovoltaics (PV) have experienced substantial commercial success on a foundation of fast large-scale deposition and processing. This type of processing, regardless of material type, nearly always results in small grain (nm to several um diameters) polycrystalline material that, if not for effective grain boundary (GB) and defect passivation, would severely limit PV performance. In the case of CdTe based PV technology, the nearly ubiquitous CdCl2 treatment is used, in part, to passivate the polycrystalline p-type absorber even though Cl is known to (and used to) compensate p-type II-VI materials. Given that VOC is still the most limited performance metric and it can only be improved through higher p-type absorber concentrations, CdCl2 treatments may be holding the technology back. In this talk, we will discuss results related to a process by which small grain CdSeTe material is rapidly transformed into very large grain material (100-1000um diameters, Fig. 1a). This explosive recrystallization, which we have termed colossal grain growth (CGG), occurs by a Cl free process with thin films (<10um) deposited using the same fast deposition techniques the industry has relied on for more than a decade. Our modeling suggests that GB recombination becomes significantly less important at these grain sizes and thus may eliminate the need for a CdCl2 treatment. This result is complimented by previous results of epitaxial growth at high rates on single crystal seed layers. Thin CdSeTe CGG seed layers can be used for rapid epitaxy of CdTe to complete a standard device stack (Fig.1b). This is an optimistic view and the current limitations and challenges related to this process and these materials will also be discussed, including alloy and substrate roughness sensitivity, intragrain material quality, and complex defect chemistry. These challenges are not insignificant but overcoming them may enable a new structural paradigm for thin-film PV.

CdTe↗