SEARCH · Search NASA

Results for “shield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Hybrid Wing Body Shielding Studies Using an Ultrasonic Configurable Fan Artificial Noise Source Generating Typical Turbofan Modes

An Ultrasonic Configurable Fan Artificial Noise Source (UCFANS) was designed, built, and tested in support of the NASA Langley Research Center's 14x22 wind tunnel test of the Hybrid Wing Body (HWB) full 3-D 5.8% scale model. The UCFANS is a 5.8% rapid prototype scale model of a high-bypass turbofan engine that can generate the tonal signature of proposed engines using artificial sources (no flow). The purpose of the test was to provide an estimate of the acoustic shielding benefits possible from mounting the engine on the upper surface of an HWB aircraft using the projected signature of the engine currently proposed for the HWB. The modal structures at the rating points were generated from inlet and exhaust nacelle configurations - a flat plate model was used as the shielding surface and vertical control surfaces with correct plan form shapes were also tested to determine their additional impact on shielding. Radiated acoustic data were acquired from a traversing linear array of 13 microphones, spanning 36 inches. Two planes perpendicular, and two planes parallel, to the axis of the nacelle were acquired from the array sweep. In each plane the linear array traversed 4 sweeps, for a total span of 168 inches acquired. The resolution of the sweep is variable, so that points closer to the model are taken at a higher resolution. Contour plots of Sound Pressure Levels, and integrated Power Levels, from nacelle alone and shielded configurations are presented in this paper; as well as the in-duct mode power levels.

Sutliff, Daniel L.↗

NASA NTRS2016

Electrodynamic Dust Shield for Space Applications

ISECG↗

NASA NTRS2016

Electrodynamic Dust Shield for Space Applications

The International Space Exploration Coordination Group (ISECG) has chosen dust mitigation technology as a Global Exploration Roadmap (GER) critical technology need in order to reduce life cycle cost and risk, and increase the probability of mission success. NASA has also included Particulate Contamination Prevention and Mitigation as a cross-cutting technology to be developed for contamination prevention, cleaning and protection. This technology has been highlighted due to the detrimental effect of dust on both human and robotic missions. During manned Apollo missions, dust caused issues with both equipment and crew. Contamination of equipment caused many issues including incorrect instrument readings and increased temperatures due to masking of thermal radiators. The astronauts were directly affected by dust that covered space suits, obscured face shields and later propagated to the cabin and into the crew's eyes and lungs. Robotic missions on Mars were affected when solar panels were obscured by dust thereby reducing the effectiveness of the solar panels. The Electrostatics and Surface Physics Lab in Swamp Works at the Kennedy Space Center has been developing an Electrodynamic Dust Shield (EDS) to remove dust from multiple surfaces, including glass shields and thermal radiators. This technology has been tested in lab environments and has evolved over several years. Tests of the technology include reduced gravity flights (6g) in which Apollo Lunar dust samples were successfully removed from glass shields while under vacuum (1 millipascal). Further development of the technology is underway to reduce the size of the EDS as well as to perform material and component testing outside of the International Space Station (ISS) on the Materials on International Space Station Experiment X (MISSE-X). This experiment is designed to verify that the EDS can withstand the harsh environment of space and will look to closely replicate the solar environment experienced on the moon. A second flight opportunity exists to provide an EDS to several companies as part of NASA's Lunar CATALYST program. The current mission concept would fly the EDS on the footpad of one of the Lunar CATALYST vehicles. To determine the effectiveness of the EDS system, image analysis will be performed on the footpad before, during and after EDS activation. If successful in these test flights, the Technology Readiness Level (TRL) of the EDS will be raised to a sufficient level to be used in the protection of mission equipment for future NASA and commercial missions to the moon, asteroids, and Mars.

Dust mitigation↗

NASA NTRS2015

Performance and Facility Background Pressure Characterization Tests of NASAs 12.5-kW Hall Effect Rocket with Magnetic Shielding Thruster

NASA's Space Technology Mission Directorate (STMD) Solar Electric Propulsion Technology Demonstration Mission (SEP/TDM) project is funding the development of a 12.5-kW Hall thruster system to support future NASA missions. The thruster designated Hall Effect Rocket with Magnetic Shielding (HERMeS) is a 12.5-kW Hall thruster with magnetic shielding incorporating a centrally mounted cathode. HERMeS was designed and modeled by a NASA GRC and JPL team and was fabricated and tested in vacuum facility 5 (VF5) at NASA GRC. Tests at NASA GRC were performed with the Technology Development Unit 1 (TDU1) thruster. TDU1's magnetic shielding topology was confirmed by measurement of anode potential and low electron temperature along the discharge chamber walls. Thermal characterization tests indicated that during full power thruster operation at peak magnetic field strength, the various thruster component temperatures were below prescribed maximum allowable limits. Performance characterization tests demonstrated the thruster's wide throttling range and found that the thruster can achieve a peak thruster efficiency of 63% at 12.5 kW 500 V and can attain a specific impulse of 3,000 s at 12.5 kW and a discharge voltage of 800 V. Facility background pressure variation tests revealed that the performance, operational characteristics, and magnetic shielding effectiveness of the TDU1 design were mostly insensitive to increases in background pressure.

Performance↗

NASA NTRS2016

Fabrication of Regolith-Derived Radiation Shields: Preliminary Results

Unlike the Earth, Mars and asteroids do not have a magnetosphere to protect humans, mechanisms and electronics from damaging Galactic Cosmic Radiation (GCR) and solar particle events (SPE). This presents one of the highest risks to crew and onboard electronics during interplanetary journeys. The goal of this project is to evaluate the effectiveness of carbonaceous asteroids and other hydrogen-rich materials as potential radiation shielding materials, which ultimately could be tested during planned crewed missions to a captured asteroid fragment (ARM). This type of investigation represents an initial effort to develop radiation shield material compositions, production methods and technologies, and optimization methodology for manufacturing radiation shields in deep space for large exploration human missions or by emerging new industries seeking to stage their spacecraft for the exploitation of the resources of asteroids. Carbonaceous chondrites (C-type) are of particular interest as sources of compounds such as water ice and hydrogen-rich carbon molecules, which can provide sufficient low Z element density to provide radiation protection at adequate shield thicknesses.

Regolith↗

NASA NTRS2016

Final Test Report: Hexavalent Chrome Free Coatings for Electronics Electromagnetic Interference (EMI) Shielding Effectiveness (SE)

The test results for Salt Spray Resistance, Static Heat and Humidity and Marine Environment can be found in Sections 3.1.3.3, 3.1.4.3 and 3.1.5.3 respectively. In summary, both the Metalast TCP and SurTec 650 Type 2 conversion coatings perform very similar to the incumbent Type 1 conversion coating against both 6061 and 5052 aluminum under all three test conditions. Significant prior work was performed to select the aluminum and conversion coating included within this test cycle; Reference - NASA GSDO Program Hexavalent Chrome Alternatives Final Pretreatments Test Report Task Order: NNH12AA45D September 01, 2013. As illustrated in the data, the 6061 aluminum panels SLIGHTLY out-performed the 5052 aluminum panels. Individual shielding effectiveness graphs for each panel are included within Appendix C and D. One other notable effect found during review of the data is that the Test Panels exposed to B117 Salt Fog reduced in shielding effectiveness significantly more than the Marine Environment Test Panels. The shielding effectiveness of the Marine Test Panels was approximately 20dB higher than the Test Panels that underwent B117 Salt Fog Exposure. The intent of this evaluation was not to maximize shielding effectiveness values. The same Parker Chomerics Cho-Seal 6503 gasket material was used for all panels with aluminum and conversion coating variants. A typical EMI gasket design for corrosive environments would be done quite differently. The intent was to execute a test that would provide the best possible evaluation of different aluminum materials and conversion coatings in corrosive environments. The test program achieved this intent. The fact that the two aluminums and two Type II conversion coatings performed similar to the incumbent Type 1 conversion coating is a positive outcome. It was desired to have an outcome that further differentiation the performance of two aluminum types and two conversion coating types but this could not be extracted by the test results. Further analysis of the test plates may be done by X-Ray Photoelectron Spectroscopy (XPS) or Electrochemical Impedance Spectroscopy (EIS). Feasibility of this is under review.

Kessel, Kurt R.↗

NASA NTRS2018

Orion Heat Shield Manufacturing Producibility Improvements for the EM-1 Flight Test Program

This paper describes how the ORION program is incorporating improvements in the heat shield design and manufacturing processes reducing programmatic risk and ensuring crew safety in support of NASA's Exploration missions. The approach for the EFT-1 heat shield utilized a low risk Apollo heritage design and manufacturing process using an Avcoat TPS ablator with a honeycomb substrate to provide a one piece heat shield to meet the mission re-entry heating environments. The EM-1 mission will have additional flight systems installed to fly to the moon and return to Earth. Heat shield design and producibility improvements have been incorporated in the EM-1 vehicle to meet deep space mission requirements. The design continues to use the Avcoat material, but in a block configuration to enable improvements in consistant and repeatable application processes using tile bonding experience developed on the Space Shuttle Transportation System Program.

Producibility↗

NASA NTRS2018

Cryogenic Hydrogen Radiation Shield for Human Spaceflight

The disclosed subject matter relates to a radiation shielding apparatus including a cryogenic vessel and a cryogenic hydrogen radiation shielding material capable of providing a radiation shield, the cryogenic hydrogen radiation shielding material including cryogenic hydrogen.

Li, Xiaoyi↗

NASA NTRS2018

Experimental Study of Noise Shielding by a NACA 0012 Airfoil

The effects of sound source location, Mach number and angle of attack on the shielding of a laser-induced sound source by a NACA 0012 airfoil are examined. The sound source is a small plasma generated by a high energy, laser beam focused to a point. In-flow microphone measurements are acquired in the midspan plane of the airfoil over a broad range of streamwise stations, and shielding levels are calculated over different frequency ranges from the measurements acquired with and without the airfoil installed. Shielding levels are shown to increase as the source is positioned closer to the mid-chord of the airfoil, and to significantly decrease with increasing flow Mach number, except when the source is positioned near the leading edge of the airfoil. Both with and without flow, changes in angle of attack are associated with a corresponding shift of the shadow region. Finally, the effects of multipath signals, observer distance and signal scatter on the measured shielding levels are discussed.

Hutcheson, Florence V.↗

NASA NTRS2016

Magnetic Shield Design Modeling and Validation for SWOT Spacecraft Ka-Band Extended Interaction Klystron

Two Extended Interaction Klystrons (EIKs) containing strong permanent magnets were modeled magnetically in a representative spacecraft geometry using commercial finite element modeling techniques and were validated against measurements made at varying distances. Initial modeling results for the 63 A-m2 (amperes per square meter) dipole moment magnets showed that magnetic shields would be necessary in order to meet magnetic field requirements for the Surface Water and Ocean Topography (SWOT) spacecraft, which contains components that are susceptible to external DC (Direct Current) magnetic fields. JPL (Jet Propulsion Laboratory) and the EIK vendor proposed cold rolled steel and mu-metal as potential shield materials along with proposed thicknesses of 0.5 millimeters and 1.5 millimeters. Magnetic shields made from each of these materials were designed and modeled in software, taking high-field saturation into account. Prototype magnetic shields with these parameters were then built, measured with an existing EIK, and compared against modeling results. For single-axis field measurements along the dipole axis, modeling results were within 7 gauss of the measured values at 10 centimeters from the magnet, and converged to less than 1.5 gauss at distances greater than 14 centimeters from the magnet. Three-axis field measurements at locations of interest showed that model correlation improved to within 4 gauss at 11 centimeters and 2 gauss for distances ranging between 15 centimeters and 36 centimeters.

Gonzales, Edward↗

NASA NTRS2017

Magnetic Shield Design Modeling and Validation on SWOT Spacecraft Applied to Mars Flux Pinning Orbiting Sample Design

A modeling methodology was developed for use on the Surface Water and Ocean Topography (SWOT) mission for the computational modeling and design of a magnetic shield for a 63 A-sq m source. Shield options were modeled and tested across various design parameters and validated with measurement. Measurement results fell within 10% of simulation in most cases of concern with sources of error well understood. These methods results informed a subsequent modeling activity for a future Mars Sample Return (MSR) mission concept with stringent magnetic cleanliness requirements to retain geologic integrity of the samples. One option for capturing the sample from orbit requires rare earth magnets in close proximity to the Martian samples. Magnetic modeling with a finite-element method solver estimated the magnetic environment and established the need for shielding. Further modeling then determined the shielding necessary to meet magnetic requirements, followed by the design of a mass-optimized solution.

Gonzales, Edward↗

NASA NTRS2016

Magnetic Shield Design Modeling and Validation for SWOT Spacecraft Ka-Band Extended Interaction Klystron

Two Extended Interaction Klystrons (EIKs) containing strong permanent magnets were modeled magnetically in a representative spacecraft geometry using commercial finite element modeling techniques and were validated against measurements made at varying distances. Initial modeling results for the 63 A-m2 dipole moment magnets showed that magnetic shields would be necessary in order to meet magnetic field requirements for the Surface Water and Ocean Topography (SWOT) spacecraft, which contains components that are susceptible to external DC magnetic fields. JPL and the EIK vendor proposed cold rolled steel and mu-metal as potential shield materials along with proposed thicknesses of 0.5 mm and 1.5 mm. Magnetic shields made from each of these materials were designed and modeled in software, taking highfield saturation into account. Prototype magnetic shields with these parameters were then built, measured with an existing EIK, and compared against modeling results. For single-axis field measurements along the dipole axis, modeling results were within 7 gauss of the measured values at 10 cm from the magnet, and converged to less than 1.5 gauss at distances greater than 14 cm from the magnet. Three-axis field measurements at locations of interest showed that model correlation improved to within 4 gauss at 11 cm and 2 gauss for distances ranging between 15 cm and 36 cm.

Gonzales, Edward↗

NASA NTRS2021

A Study of Layered Structural Configurations as Thermal and Impact Shielding of Lunar Habitats

The focus of this study is the analysis of a proposed multilayer material configuration as lunar habitat shielding so as to assess its ability to resist temperature extremes and impact. In order to resist this environmental hazard, the analysis will compare various configurations of potential shielding layers using both in-situ resource utilization (ISRU) and Earth-based materials. The technology for implementation of in-situ resources in construction is developing, though not yet able to produce a functional lunar habitat. As the lunar infrastructure is developed, ISRU techniques for manufacturing and construction may become more viable. Therefore, both types of materials are considered due to potential for application towards both near-term and long-term commencements of habitat construction. The thermal analysis in this paper utilizes the nonlinear heat equation to produce a depth-dependent temperature gradient from the habitat exterior to the interior that changes continuously with time during the lunar diurnal cycle. Static loading conditions meant to simulate the impact force of a 77.9 g meteorite were used to analyze the ability of a proposed multilayer shielding configuration to resist impact. A thermal stress analysis was performed to observe the effects of heat transfer through the proposed multilayer configuration. The results of this study should be useful in determining the potential for implementation of efficient shielding layers for the initial lunar base.

Layered systems↗

NASA NTRSDate not supplied

Testing the Effectiveness of Integrated Plume Shield for a Hall Thruster

Hall thrusters have been shown to exhibit side plumes with varying degree of erosive power. This article presents the concept of the integrated plume shield for the purpose of mitigating the erosive power of said side plume. A test was conducted on a low-power Hall thruster with and without integrated plume shield and the effect on thruster performance and plume characteristics were measured. Collected data shows that the thruster performed identically to within uncertainty in terms of thrust, specific impulse, and discharge oscillation characteristics. Plume measurements showed up to a 48% reduction in ion current density when averaging over 80° to 105° from the firing axis. A brief analytical study was performed to determine the advantages and disadvantages of using integrated plume shield as opposed to using spacecraft surface covering and placing thrusters on booms. The integrated plume shield was found to provide varying level of advantages in mass, design restrictions, and complexity, which are likely to lead to major cost savings in the long term.

Electric Propulsion↗

NASA NTRSDate not supplied

Development of a Generic Small-Satellite Payload for On-Orbit Characterization and Evaluation of Novel Radiation-Shielding Materials

There is a need for lightweight and novel radiation shielding for small satellites operating in LEO and beyond. Current state of the art shielding materials include aluminum and polyethylene, or no shielding due to weight and dimensional considerations. New materials are being developed which may offer advantages over current options. These materials include novel lightweight composites impregnated with metallic nanoparticles, chitin-derived bioplastics, and aerogel-family materials. A compact experiment platform that allows the simultaneous testing of a number of potential shielding materials will be useful in comparing and validating them. The effort now underway seeks to develop a miniaturized, modularized payload which will allow testing of materials using 1U CubeSat form factor modules with four scintillator radiation detectors arrayed behind four sample material windows exposed to space. The first proposed mission will utilize a 2U payload volume to host two test quartets enabling eight materials to be tested. Such a test platform can potentially be used as a hosted payload on a variety of spacecraft to test other materials in the future.

Avery D Brock↗

NASA NTRSDate not supplied

Development of a Universal Small-Satellite Payload for On-Orbit Characterization and Evaluation of Novel Radiation-Shielding Materials

There is a need for novel lightweight radiation shielding materials for small satellites operating in LEO and beyond. Current commonly used shielding materials include aluminum and polyethylene, though often no additional shielding than that provided by structure is used due to mass and dimensional constraints. New materials are being developed which may offer advantages over these current solutions. These materials include novel lightweight composites impregnated with metallic nanoparticles, chitin-derived bioplastics, and aerogel-family materials. A compact CubeSat experiment payload that allows the simultaneous testing of numerus potential shielding materials would be useful to enable material comparison and efficacy validation. An effort currently underway seeks to develop such a miniaturized modularized payload, which will enable the testing of materials in 1U CubeSat form factor modules, with each module hosting four scintillator radiation detectors arrayed behind four sample material windows exposed to space. The first proposed mission will utilize a 2U payload volume to host two test quartets enabling eight materials to be tested. Such a test platform can potentially be used as a hosted payload on a variety of spacecraft to test additional materials in the future

Luke Idziak↗

DOE OSTI2025

Warpage-Resistant, Under-Extrusion-Free, High-Surface-Quality Additive Manufacturing Process for Polyethylene-Based Composite Radiation Shielding Material

Polyethylene (PE) is one of the best shielding materials for primary space radiation due to its high hydrogen content. For effective secondary neutron shielding, boron-rich fillers are incorporated to enhance performance. The semicrystalline nature and high thermal expansion coefficient of PE impede its adoption for in situ additive manufacture in space via the fused deposition modeling (FDM) 3D printing. Here, we developed an optimized PE blend to mitigate the effects of under-extrusion and warpage. Guided by studies on extrusion and warpage, we developed an optimal set of printing parameters for the proposed PE blend. The optimum PE blend─both in its pure form and when doped with fillers─has been tested on different FDM printers. The printed structures exhibit high and uniform density, smooth surfaces, no warpage, and competitive mechanical properties. The FDM-printed plates demonstrate efficient shielding from thermal neutrons, predicted via modeling and confirmed experimentally using extended Q-range small-angle neutron scattering.

additive manufacturing↗

NASA NTRS1965

Synthesis of spherical minimum-weight proton shields

A systematic method has been developed for minimizing spherical shield weights for protection against proton radiation, including secondary neutron production, subject to various specified dose constraints. Variational methods are applied to a radiation model yielding the choice of optimum shielding materials and their mixtures, together with a prescription for their disposition in a multilayer spherical shield.

Spherical Shell↗