Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulation tools”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Two-Dimensional Computational Fluid Dynamics and Conduction Simulations of Heat Transfer in Horizontal Window Frames with Internal Cavities

This paper assesses the accuracy of the simplified frame cavity conduction/convection and radiation models presented in ISO 15099 and used in software for rating and labeling window products. Temperatures and U-factors for typical horizontal window frames with internal cavities are compared; results from Computational Fluid Dynamics (CFD) simulations with detailed radiation modeling are used as a reference. Four different frames were studied. Two were made of polyvinyl chloride (PVC) and two of aluminum. For each frame, six different simulations were performed, two with a CFD code and four with a building-component thermal-simulation tool using the Finite Element Method (FEM). This FEM tool addresses convection using correlations from ISO 15099; it addressed radiation with either correlations from ISO 15099 or with a detailed, view-factor-based radiation model. Calculations were performed using the CFD code with and without fluid flow in the window frame cavities; the calculations without fluid flow were performed to verify that the CFD code and the building-component thermal-simulation tool produced consistent results. With the FEM-code, the practice of subdividing small frame cavities was examined, in some cases not subdividing, in some cases subdividing cavities with interconnections smaller than five millimeters (mm) (ISO 15099) and in some cases subdividing cavities with interconnections smaller than seven mm (a breakpoint that has been suggested in other studies). For the various frames, the calculated U-factors were found to be quite comparable (the maximum difference between the reference CFD simulation and the other simulations was found to be 13.2 percent). A maximum difference of 8.5 percent was found between the CFD simulation and the FEM simulation using ISO 15099 procedures. The ISO 15099 correlation works best for frames with high U-factors. For more efficient frames, the relative differences among various simulations are larger. Temperature was also compared, at selected locations on the frames. Small differences was found in the results from model to model. Finally, the effectiveness of the ISO cavity radiation algorithms was examined by comparing results from these algorithms to detailed radiation calculations (from both programs). Our results suggest that improvements in cavity heat transfer calculations can be obtained by using detailed radiation modeling (i.e. view-factor or ray-tracing models), and that incorporation of these strategies may be more important for improving the accuracy of results than the use of CFD modeling for horizontal cavities.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Results of External Technical Reviews of Site Modeling Efforts That Support System Plans

An External Technical Review (ETR) team evaluated the system-level modeling and simulation tools in support of Savannah River Site and Office of River Protection liquid waste processing and disposal systems. The reviews focused on the following primary areas: software and modeling tools, capability to model needed facilities and operations, rate at which predictions are performed, and need for additional tools. The Liquid Waste Disposition Systems at these sites are highly integrated operations that involve safely storing liquid waste in underground storage tanks; removing, treating, and disposing low-activity fraction on-site; vitrifying high-level waste; and storing the vitrified waste until permanent disposition at a Federal Repository. The purpose of the ETR team was to evaluate the current process simulation tools that support the planning basis for life cycle liquid waste disposition system plans. These plans establish a base for processing the constituents of liquid waste systems to the end of the program mission. Observations and recommendations were made for each of the review areas. In general, tools appear to provide reasonable estimates for their intended purposes; however, additional functionality and new tools are needed, as well as greater flexibility and improved performance in producing estimates for planning purposes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Performance evaluation of surface riding wave energy converter with linear electric generator

In this work, we devised a new WEC (wave energy converter) called SR-WEC (Surface Riding WEC). The SR-WEC consists of two bodies: the outer cylinder with an armature assembly (body #1) and a magnet assembly (body #2) sliding inside the armature. For the SR-WEC, the relative sliding displacement and velocity are caused by gravity acceleration and the outer cylinder's motions, and they lead to electrical power generation. To evaluate its performance, a numerical simulation tool was developed, which solves the fully-coupled floater-mooring-generator dynamics. During the developing stage, the appropriate hydrodynamics model, sliding mechanics model, mooring dynamics model, and LEG (linear electric generator) electro-magnetic model were independently developed and then fully coupled in time domain to account for the cross-coupling interactions among them. Then, the developed simulation tool was verified component by component against various laboratory tests. Subsequently, systematic parametric studies were conducted with several important design parameters under various wave conditions to enhance power generation. After that, the average output power was evaluated in enlarged operational wave conditions. The present SR-WEC is particularly designed to be efficient at low sea states, which is good since they cover the majority of typical annual sea states.

42 ENGINEERING↗

Computational analysis of deployable wind turbine systems in defense operational energy applications.

The U.S. military has been exploring pathways to reduce the logistical burden of fuel on virtually all their missions globally. Energy harvesting of local resources such as wind and solar can help increase the resilience and operational effectiveness of military units, especially at the most forward operating bases where the fuel logistics are most challenging. This report considers the potential benefits of wind energy provided by deployable wind turbines as measured by a reduction in fuel consumption and supply convoys to a hypothetical network of Army Infantry Brigade Combat Team bases. Two modeling and simulation tools are used to represent the bases and their operations and quantify the impacts of system design variables that include wind turbine technologies, battery storage, number of turbines, and wind resource quality. The System of Systems Analysis Toolkit Joint Operational Energy Model serves as a baseline scenario for comparison. The Hybrid Optimization of Multiple Energy Resources simulation tool is used to optimize a single base within the larger Joint Operational Energy Model. The results of both tools show that wind turbines can provide significant benefits to contingency bases in terms of reduced fuel use and number of convoy trips to resupply the base. The match between the turbine design and wind resource, which is statistically low across most of the global land area, is a critical design consideration. The addition of battery storage can enhance the benefits of wind turbines, especially in systems with more wind turbines and higher wind resources. Wind turbines may also provide additional benefits to other metrics such as resilience that may be important but not fully considered in the current analysis. ACKNOWLEDGEMENTS The authors would like to thank the following individuals for their helpful support, feedback and review to improve this report: U.S. Department of Energy Wind Energy Technologies Office, Patrick Gilman and Bret Barker; Idaho National Laboratory, Jake Gentle and Bradley Whipple; The National Renewable Energy Laboratory, Robert Preus and Tony Jimenez; Sandia National Laboratories, Alan Nanco, Dennis Anderson, and Hai Le. In addition, numerous discussions with military and industry stakeholders over the year were invaluable in focusing the efforts represented in this report.

17 WIND ENERGY↗

Plasma Surface Interactions: Bridging from the Surface to the Micron Frontier through Leadership Class Computing (Final Technical Progress Report)

The performance demands on plasma-facing components (PFCs) in future fusion power plants are beyond the capability of current materials. In defining the plasma-surface interaction (PSI), it is evident that three coupled spatial regions influence PFC materials evolution and performance. These regions consist of (1) the edge and scrape-off layer region of the plasma, (2) the near-surface material response to extreme thermal and particle fluxes under the influence of, and feedback to, the plasma sheath, and (3) the structural material’s response to an intense, 14 MeV peaked neutron spectrum, which produces very high concentrations of transmuted elements through (n,p) and (n,α) reactions and structural material property degradation. The objective of this project is to develop and deploy validated, high-performance simulation tools capable of predicting the performance of tungsten-based plasma-facing components (PFCs) in a burning fusion plasma environment, which includes modeling surface morphology evolution in either erosion or re-deposition regimes, and the recycling of hydrogen species. This requires the development of a leadership-scale computational code to predict PFC behavior that is well integrated to a suite of multiscale modeling techniques to bridge the scales needed to address complex physical and computational issues at the plasma surface interface and the transition region below the surface where neutron damage processes in the bulk dominate material behavior. Successful completion of this project will provide PFC simulation tools to evaluate steady-state performance of tungsten-based PFC and divertor components in burning plasma environments. This will enable the identification of critical experiments to confirm whether practical PFC solutions exist for magnetic fusion energy beyond ITER. More specifically, the research activities within this project focus on two broadly defined research thrusts: 1) Developing a new simulation code, Xolotl-PSI to predict PFC operating lifetime and performance, that is specifically designed to take advantage of leadership class computing facilities; and 2) Integrating and applying discrete particle-based, as well as continuum-based, multiscale modeling techniques to provide scientific discovery of the mechanisms controlling PFC and bulk materials evolution under fusion plasma and 14-MeV neutron exposure; in this thrust, the challenge of scale-bridging between atomistic/microstructural modeling and the continuum-scale of PFC device performance is achieved through multiscale modeling techniques. Throughout the grant period, research at UMass Amherst focused on the atomic-scale analysis of the dynamics and kinetics (transport and reactions) of small mobile helium clusters near surfaces and grain boundaries in plasma-exposed tungsten, as well as the proper parameterization and incorporation of these processes into our SciDAC team’s continuum-level cluster dynamics code (Xolotl). Our work also included characterization of large-scale molecular-dynamics (MD) simulation results of helium implantation into tungsten based on the findings of our analysis and comparisons of Xolotl simulation predictions with the large-scale MD simulation results for Xolotl validation purposes; emphasis was placed on the impact of helium cluster dynamics/kinetics on tungsten surface morphology, near-surface tungsten structure, and helium retention. Furthermore, our work included initiation of a research program on evaluating the impact of structural defects in tungsten due to plasma exposure (such as helium nanobubbles) on tungsten’s thermophysical properties, focusing on lattice thermal conductivity. Our studies contributed to a fundamental understanding of the effects of plasma-surface interactions on the dynamical response of plasma-facing materials in nuclear fusion devices and the development of predictive hierarchical multiscale computational tools for the quantitative description of the material’s dynamical response to plasma exposure.

36 MATERIALS SCIENCE↗

Pathway Controlled Penetration (PcP) [Slides]

The technical approach employs advanced computational simulation tools to demonstrate how current assets can destroy RWK-RFI-12-0001's HDBT, a tunnel complex with two portals built into the base of a granite mountain. The granite over layer is assumed to be 60 meters thick over both portals and 80 meters over the facility's mission space. Key S&T is the completed development of a highly innovative viscoplastic fracture material model, 3D parallel gas-fracture capabilities into FDEM, and a stochastic handling of the material properties. Phase I - Develop and validate code simulation tools: (1) develop, incorporate and validate AZ-Frac material model for granite; and (2) Develop and incorporate gas-driven-fracture modeling into LANL's FDEM MUNROU code; (3) Develop and incorporate stochastic features into FDEM modeling. Phase II - Conduct PcP analysis on above HDBT: (1) Acquire HDBT design data, develop simulation model; and (2) Evaluate and select most promising defeat alternative. Phase III - Deliver code, train Service target analysts, and conduct simulations against real world HDBTs. PcP uses advanced computer simulations to enhance HDBT functional defeat efforts. Newly developed material models that account for fractural energy coupled with the finite discrete element methodology (FDEM) will provide targeting packages that will create penetration avenues for current or future lethality options. This novel computational approach requires full 3D geologic and structure characterization as well as significant high performance computing capabilities. The goal is to distinctively alter the targeting paradigm by leveraging critical DoD assets along with insitu geologic strata. In other words, assets will utilize underground rock structure to their benefit by creating rubbilization zones that will allow pathway controlled penetration.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

An open-source hybrid unstructured mesh - CAD fusion multiphysics analysis workflow in SALAMANDER

Plasma facing components in fusion devices will endure extreme neutron and heat fluxes. To facilitate their design using simulation tools, the open-source Fusion Module, Fusion ENergy Integrated multiphys-X (FENIX) framework is being developed to model these components with a high-fidelity multi-physics multi-dimensional approach. It can iteratively resolve couplings between all the physics at play, from neutron radiation, to thermomechanics, to near-wall plasma dynamics. This framework is based on the Multiphysics Object Oriented Simulation Environment (MOOSE), which is developed by a collaboration of US National Laboratories since 2008, for advanced nuclear, geomechanics simulations and other applications. FENIX couples numerous simulation tools, including OpenMC, the Tritium Migration Analysis Program v8, the NekRS CFD software, and most MOOSE modules. For the coupling of radiation transport and other physics, FENIX supports a hybrid workflow between Computer Assisted Design (CAD) and unstructured mesh geometries. The CAD can be generated from skinning the unstructured mesh, to enable a coarse geometry for efficient particle transport, but still resolving the local material compositions and temperature gradients. Neutron transport is performed using DAGMC on the CAD, and Cardinal, integrated in FENIX, maps tallied quantities, such as the heat deposition or the tritium generation rates, from a tally volumetric mesh to the other physics’ unstructured mesh. This coupling was exercised on a simplified tokamak geometry, coupling neutron transport with the heat conduction equation, and on a monoblock divertor problem, coupling additionally with tritium migration. Mesh convergence studies highlight the importance of the mapping conservativeness. Coupling with thermo-mechanics is further enabled by the generalization of the approach to moving meshes. The presentation will include these coupled analysis as well as an update on status of the FENIX framework.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗

SU-G-TeP1-12: Random Repainting as Mitigation for Scanned Ion Beam Interplay Effects

Purpose: Interference of dose application in scanned beam particle therapy and organ motion may lead to interplay effects with distorted dose to target volumes. Interplay effects depend on the speed and direction of the scanning beam, leading to fringed field edges (scanning parallel to organ motion direction) or over- and under-dosed regions (both directions are orthogonal). Current repainting methods can mitigate interplay effects, but are susceptible to artefacts when only a limited number of repaints are applied. In this study a random layered-repainting strategy was investigated. Methods: Mono-energetic proton beams were irradiated to a 10 ×10 cm{sup 2} scanned field at a Varian ProBeam facility. Applied dose was measured with a 2D amorphous silicon detector mounted on a motion platform (CIRS dynamic platform). Motion was considered with different cycles, directions and translations up to ±8 mm. Dose distributions were measured for a static case, regular repainting (repeated meander-like path) and random repainting. Latter was realized by randomly distributing single spot locations during irradiation for a given number of repaints. Efficiency of repainting was analyzed by comparison to the static case. A simulation tool based on treatment logs and motion information was developed to compare measurement results to expected dose distributions. Results: Regular repainting could reduce motion artefacts, but dose distortion was strongly dependent on motion direction. Random repainting with same number of repaints (N=4) showed superior results, independent of target movement direction, while introducing slight penalty on delivery times, caused by an increase of overall scanning travel distance. The simulation tool showed good agreement to measured results. Conclusion: The results demonstrate significant improvement in terms of dose conformity when layered repainting is applied in a randomized fashion. This allows for reduced target margins during treatment planning and limited number of repaints. A combination with e.g. respiratory gating is straight-forward. Authors are employees of Varian Medical Systems Particle Therapy GmbH.

43 PARTICLE ACCELERATORS↗

New Virtual Test Bed Capabilities: Virtual DOME Model and New Updates to Repository

The Department of Energy (DOE) Office of Nuclear Energy National Reactor Innovation Center accelerates the deployment of novel reactor concepts by establishing both physical and virtual spaces for building and testing various components, systems, and complete pilot plants. The Virtual Test Bed represents the virtual arm of the National Reactor Innovation Center and is a joint effort with the DOE Nuclear Energy Advanced Modeling and Simulation Program. The Virtual Test Bed mission is to accelerate the deployment of advanced reactors by facilitating the adoption of cutting-edge DOE advanced modeling and simulation tools to design, evaluate, and license reactors. This is primarily achieved by storing example challenge problems in an externally available repository and by developing models to fill the M&S gaps needed for potential demonstrators. Activities conducted this fiscal year focused on developing of a Demonstration of Microreactor Experiments shield model to help accelerate the confirmatory analysis required for the reactor demonstration. This model and workflow will allow developers to leverage advanced modeling and simulation tools to ensure their reactor demonstration concept will meet dose requirements and that the surrounding shield will stay within concrete temperature limits during steady-state and transient operation conditions. An initial model has been developed to evaluate the temperature distribution in the concrete shield during steady-state operation, including neutron and gamma heating effects. Various modeling strategies have been examined to understand their applicability and limitations with different reactor designs to make the workflow as reactor-agnostic as possible and computationally effective to maximize its usability. In addition to describing the Demonstration of Microreactor Experiments shield model and associated results, this report summarizes other accomplishments regarding repository maintenance and improvement and new external models hosted on the repository.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

The Next-Generation Ecosystem Experiment Arctic Rainfall Simulator: a tool to understand the effects of changing rainfall patterns in the Arctic

Rainfall frequency and intensity are expected to increase in the Arctic, with potential detrimental impacts on permafrost, leading to enhanced thawing and carbon release to the atmosphere. However, there have been very few studies on the effect of discrete rain events on permafrost in the Arctic and sub-Arctic. Conducting controlled rainfall experiments within permafrost landscapes can provide an improved understanding of the effect of changing intensity, duration, and timing of rain events on permafrost tundra ecosystems. Here, we describe the design and implementation of the Next-Generation Ecosystem Experiment Arctic Rainfall Simulator (NARS), a variable intensity (4–82 mm/h) rainfall simulator that can be used to study the effects of rainfall on permafrost stability. The NARS design includes a 3D-printed 4 cm H-flume and uses an eTape resistivity sensor that was calibrated (R 2 = 0.9–0.96) to measure discharge from the system. NARS is designed to be lightweight, simple to construct, and can be easily deployed in remote locations. As a field validation of updated rainfall simulator design and modernized controls, NARS was tested on the Seward Peninsula, AK. Because of its portability, versatility in deployment, dimensions, and rainfall intensity, NARS represents a methodological innovation for researching the impacts of rainfall on permafrost environments.

54 ENVIRONMENTAL SCIENCES↗

DESIGN AND EXPERIMENTAL STUDY OF A HIGH PRESSURE AND SUPERCRITICAL METHANE-OXYGEN BURNER

Directly heated supercritical oxy-fuel power cycles have potential to offer a higher thermal efficiency and lower pollutant emissions compared to existing power cycles. Recent thermodynamic analysis of the cycle performed by several groups including the UTEP-Air Liquide research team show that combustion in the vicinity of 300 bar pressure and 1000-1400 K temperature allows for relatively high system efficiencies while operating within the limit of practical combustor materials. However, the realization of directly heated supercritical power cycle requires combustion systems be designed to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 K), where not only the thermodynamic properties but also the combustion properties and kinetics are unexplored. To minimize these knowledge gaps, some intermediate pressure ranges (up to 20 bar) are experimented and modeled using a CFD simulation tool. The knowledge obtained from the high pressure test will assist in understanding the combustion chamber pressurization mechanism, ignition and flame behavior at the elevated pressure. This is a systematic first step in testing at higher pressures of 100 and 300 bar pressures. The primary objective of this dissertation is to perform qualitative analysis on oxy-methane combustion at high pressure (< 20 bar) and compare to CFD model for future scale up to supercritical condition. For modeling of the system, a commercial computational fluid dynamics simulation tool, ANSYS Fluent, is used. The inlet conditions for the CFD analysis are obtained from the experiments. The geometry used for the study is same as the test apparatus and operates at the same power ratings. The expertise gained from this experimental study is important to accurately and safely design combustors at elevated pressures up to 300bar. A high pressure methane-oxygen fuel burner and combustor have been developed to accommodate oxycombustion environment. A detailed CFD analysis is conducted to understand the flame length and cooling phenomenon inside the combustor first at pressures up to 20 bar to compare to experiments then at supercritical pressure. The first part of the dissertation compares CFD results with high pressure burner experiments at pressures up to 20 bar. The test is conducted for 30 s within 150 kW – 250 kW thermal power inputs. Afterwards, based on the simulation results a cooling system is proposed for steady state high pressure combustion experiments. It is observed from the experimental study that the proposed pressurization mechanism able to pressurize the vessel up to 20 bar. It is also determined that the current combustor can operate up to 20 bar for short term. The steady state CFD simulation demonstrates that a cooling system must be incorporated for continuous operation. Additionally, the study focuses on the ignition delay due to added diluent during the combustion process. It is observed that as the carbon dioxide recirculation ratio increases the ignition delay time increases. Later part of the dissertation provides a preliminary guideline for developing a laboratory scale supercritical oxy combustor. The employment of supercritical fluid in gas turbine is fairly a new concept. Hence, there are many questions that need to be answered. During this dissertation study an investigation is performed to understand the impact of equation of state in the supercritical combustion simulation. Finally, a CFD model for developing supercritical oxy-methane burner and the combustor, incorporating real gas model, is presented. Although Lee-Kesler equation of state provides better accuracy than Peng Robinson, due to the computational time Peng Robinson equation of state is used for the simulation. It is found that existing knowledge is not enough to simulate combustion at supercritical phase. Detailed combustion chemistry at the supercritical condition must be developed and should be incorporated to accurately replicate the combustion phenomenon.

Chowdhury, ASM Arifur Rahim↗

An approach for coupled-code multiphysics core simulations from a common input

This study describes an approach for coupled-code multiphysics reactor core simulations that is being developed by the Virtual Environment for Reactor Applications (VERA) project in the Consortium for Advanced Simulation of Light-Water Reactors (CASL). In this approach a user creates a single problem description, called the “VERAIn” common input file, to define and setup the desired coupled-code reactor core simulation. A preprocessing step accepts the VERAIn file and generates a set of fully consistent input files for the different physics codes being coupled. The problem is then solved using a single-executable coupled-code simulation tool applicable to the problem, which is built using VERA infrastructure software tools and the set of physics codes required for the problem of interest. The approach is demonstrated by performing an eigenvalue and power distribution calculation of a typical three-dimensional 17 × 17 assembly with thermal–hydraulic and fuel temperature feedback. All neutronics aspects of the problem (cross-section calculation, neutron transport, power release) are solved using the Insilico code suite and are fully coupled to a thermal–hydraulic analysis calculated by the Cobra-TF (CTF) code. The single-executable coupled-code (Insilico-CTF) simulation tool is created using several VERA tools, including LIME (Lightweight Integrating Multiphysics Environment for coupling codes), DTK (Data Transfer Kit), Trilinos, and TriBITS. Parallel calculations are performed on the Titan supercomputer at Oak Ridge National Laboratory using 1156 cores, and a synopsis of the solution results and code performance is presented. Finally, ongoing development of this approach is also briefly described.

97 MATHEMATICS AND COMPUTING↗

Phenomena Important in Molten Salt Reactor Simulations

The U.S. Nuclear Regulatory Commission (NRC) is preparing for the future licensing of advanced reactors that will be very different from current light water reactors. Part of the NRC preparation strategy is to identify the simulation tools that will be used for confirmatory safety analysis of normal operation and abnormal situations in those reactors. This report advances that strategy for reactors that will use molten salts (MSRs). This includes reactors with the fuel within the salt as well as reactors using solid fuel. Although both types are discussed in this report, the emphasis is on those reactors with liquid fuel because of the perception that solid-fuel MSRs will be significantly easier to simulate. These liquid-fuel reactors include thermal and fast neutron spectrum alternatives. The specific designs discussed in the report are a subset of many designs being considered in the U.S. and elsewhere but they are considered the most likely to submit information to the NRC in the near future. The objective herein, is to understand the design of proposed molten salt reactors, how they will operate under normal or transient/accident conditions, and what will be the corresponding modeling needs of simulation tools that consider neutronics, heat transfer, fluid dynamics, and material composition changes in the molten salt. These tools will enable the NRC to eventually carry out confirmatory analyses that examine the validity and accuracy of applicant’s calculations and help determine the margin of safety in plant design.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Efficiency-Optimized Dual Fuel Engine with In-Cylinder Gasoline/CNG Blending

The objective of the proposed project is to demonstrate targeted blending of gasoline and natural gas as a means to reduce petroleum consumption of light-duty spark-ignition engine vehicles by at least 50%. This goal will be achieved through petroleum displacement with natural gas (NG) combined with a relative engine efficiency improvement in excess of 10% while meeting retrofitability requirements with an anticipated payback period of less than 36 months. Further through NG direct injection (DI) a 10% improvement in power density over the PFI baseline will be demonstrated. The proposed project employs a sound R&D approach and combines experimental work with state-of-the-art computational modeling to be able to demonstrate the ambitious project goals. The project spans a 30 month period and is divided in 3 phases with the initial phase focused on experimental characterization of the gaseous jet structure of the high-pressure NG DI injector which is used to validate the 3D-CFD simulation tool. The phase also includes an experimental demonstration of the fundamental feasibility of the proposed dual-fuel approach on an automotive single-cylinder research engine. The scope of the second phase includes optimization of the combustion system by means of virtual design combined with 3D-CFD analysis. The resulting optimized combustion system will be built and experimentally evaluated by the end of the 12 month period. The third and final phase expands the scope by integrating the engine results in a vehicle level simulation tool with the objective of developing an optimized engine control strategy that maximizes the efficiency benefits attainable with the limited on-board NG supplies. A detailed cost analysis to verify that the 36 month amortization period requirement is met will conclude the proposed effort.

42 ENGINEERING↗

Real-Sim Flexible Interface for X-in-the-loop Simulation (FIXS)

Real-Sim is a multi-resolution X-in-the-loop simulation framework to support inclusive testing and evaluation of CAVs before actual implementation in the real world. Real-Sim framework connects different simulation components and integrates various traffic and vehicle simulation tools, virtual environments, and XIL systems through a Flexible Interface for XIL Simulation (FIXS). Connections among different tools are transparent to users and handled by the interface behind the scenes. Co-simulation of various vehicle and traffic simulation tools with different XIL systems can be easily achieved and become a transparent "plug-and-play" process to users.

Shao, Yunli (0000000185287925)↗

Validating Connected, Automated, and Electric Vehicle Models and Simulation - Research Performance Progress Report

The objective of this project is to test connected and automated vehicles with both electrified and internal combustion engine powertrains to support updates and validation of modeling and simulation tools. This includes the development of the components and network architecture to execute and collect empirical data for multiple scenarios and traffic interactions. Specific program objectives include: • Translate Lab algorithms into vehicle and infrastructure controls • Conduct physical testing at realistic scale • Evaluate system performance • Improve models using empirical data • Improve control algorithms from lessons learned • Identify system and algorithm assumptions which need refinement It is important to note that the objective of this project was not to demonstrate the efficacy of the selected algorithms to improve energy efficiency but rather to validate and improve modeling and simulation tools using empirical data. While it is a desirable outcome to concurrently demonstrate improved energy efficiency through use of these algorithms, and in most cases that was the outcome, the success of this project was not predicated on the performance of the algorithm towards improving energy efficiency across all scenarios and test matrices.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

A Blockchain Based Co-Simulation Framework for Integrating DERs to Wholesale Electricity Markets

As the number of distributed energy resources (DERs) continue to increase across energy-delivery systems, there remains a need for integrating their capabilities into traditional grid operations. In this paper, a blockchain-based solution is proposed to facilitate FERC's Order No. 2222 implementations. The presented use-case enables small-scale DERs to participate in wholesale market operations through DER aggregators, while also enabling local distribution system operators to enforce distribution system constraints in a secure and traceable manner. The presented use case is built around the Unified Testing Platform (UTP) being developed as a part of the Blockchain for Optimized Security and Energy Management (BLOSEM) project. This is a multi-lab effort intended to simplify the deployment of blockchain-powered grid solutions by enabling the integration of simulation tools, and blockchain technologies through the use of system-agnostic interfaces that provide a modular, interoperable, and reusable connectivity layer.

blockchain interoperability↗

Two-Dimensional Neutronic and Fuel Cycle Analysis of the Transatomic Power Molten Salt Reactor

This status report presents the results from the first phase of the collaboration between Transatomic Power Corporation (TAP) and Oak Ridge National Laboratory (ORNL) to provide neutronic and fuel cycle analysis of the TAP core design through the Department of Energy Gateway for Accelerated Innovation in Nuclear, Nuclear Energy Voucher program. The TAP design is a molten salt reactor using movable moderator rods to shift the neutron spectrum in the core from mostly epithermal at beginning of life to thermal at end of life. Additional developments in the ChemTriton modeling and simulation tool provide the critical moderator-to-fuel ratio searches and time-dependent parameters necessary to simulate the continuously changing physics in this complex system. Results from simulations with these tools show agreement with TAP-calculated performance metrics for core lifetime, discharge burnup, and salt volume fraction, verifying the viability of reducing actinide waste production with this design. Additional analyses of time step sizes, mass feed rates and enrichments, and isotopic removals provide additional information to make informed design decisions. This work further demonstrates capabilities of ORNL modeling and simulation tools for analysis of molten salt reactor designs and strongly positions this effort for the upcoming three-dimensional core analysis.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗