SEARCH · Search NASA

Results for “single-crystals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Stability of Y-Ba-Cu-oxide phases in salt flux

The results of an investigation into the possibility of growing YBa2Cu3O7 (or Y123) single crystals from a NaCl-KCl flux (salt flux) are presented. They are compared with results for Y123 crystals grown from a Ba-Cu-oxide flux system. The chosen salt flux composition was 1:1 (NaCl:KCl). The preparation method of the solutes is presented, with particular attention given to the compounds surrounding the Y123 phase, such as Y2BaCuO6 (Y211). Optical microscopy was introduced to study the morphology of the sample; X-ray diffraction was used for phase identification; and a chemical analysis was effected. The Y123, Y211, and BaCuO2 phases were shown to be dissociated in the NaCl-KCl flux, and could not be recrystallized. A small amount of the flux could be added to create large-grain Y123 crystals, but single-crystal growth was not possible in a top-seeded NaCl-KCl solution. This is attributed to significant differences in solubility of the crystal elements, and phase separation caused by CuO crystal formation.

Tao, Y. K.↗

NASA NTRS1990

Experimental approaches for improving SiGe thermoelectric efficiency at JPL

Efforts to improve the thermoelectric efficiency of silicon-germanium alloys are discussed. These efforts are essentially focused on substantially enhancing carrier concentration levels and thus increasing the power factor values of n-type materials. With the help of thermodynamic phase diagram calculations, a combination of various crystal growth and dopant saturation techniques is used for this purpose. Bulk polycrystal growth of double-doped materials is achieved by zone leveling while a new method (the traveling heater method) for high-quality single-crystal growth of SiGe is being developed. Thin films of homogeneous single-crystalline multidoped Si80Ge20 have also been successfully grown from low-temperature melts to investigate combined dopant solid solubility variations. Very high carrier concentration levels were obtained by (P+As)-combined diffusion in zone-leveled and hot-pressed materials. The good overall understanding of doping mechanisms which has been achieved should enable optimization of the thermoelectric properties over this extended carrier concentration range. Reductions in thermal conductivity are being sought by introduction of very small phonon scattering centers (inert material) in the initial powders-precursors of Si-Ge alloys. This approach should benefit both n- and p-type materials.

Borshchevsky, Alex↗

NASA NTRS1990

Peeled film GaAs solar cell development

Thin-film, single-crystal gallium arsenide (GaAs) solar cells could exhibit a specific power approaching 700 W/kg including coverglass. A simple process has been described whereby epitaxial GaAs layers are peeled from a reusable substrate. This process takes advantage of the extreme selectivity of the etching rate of aluminum arsenide (AlAs) over GaAs in dilute hydrofluoric acid. The feasibility of using the peeled film technique to fabricate high-efficiency, low-mass GaAs solar cells is presently demonstrated. A peeled film GaAs solar cell was successfully produced. The device, although fractured and missing the aluminum gallium arsenide window and antireflective coating, had a Voc of 874 mV and a fill factor of 68 percent under AM0 illumination.

Wilt, D. M.↗

NASA NTRS1990

Buried homojunction solar cells formed in p-InP during sputter deposition and hydrogen plasma processing

Although it is apparent that direct current (DC) magnetron sputter deposition of indium tin oxide (ITO) leads to the formation of a buried homojunction in single-crystal p-type InP, the actual mechanism of type conversion of the InP surface is not clear. Since sputter deposition of In2O3 has also led to high-quality cells, it appears that Sn is not the cause of type conversion. To investigate the junction formation process further, experiments involving the use of a pure hydrogen plasma have been performed, resulting in type conversion of Fe-doped InP surfaces and in solar cells with efficiencies over 16 percent (global). The results confirm that sputter deposition is not necessary to form this type of buried homojunction solar cell, and they suggest a fabrication process that may be used with other relevant photovoltaic materials.

Gessert, T. A.↗

NASA NTRS1990

23.5 percent thin-film space concentrator cells

Thin-film AlGaAs-GaAs double-heterostructure concentrator cells were fabricated which exhibit total-area conversion efficiencies as high as 23.5 percent AM0 at 100 suns, 25 C. This is one of the best space concentrators measured to date at NASA and is designed for a thin-film cell without a prismatic coverglass. This solar cell structure consists of a GaAs/AlGaAs film less than 5 micron thick mounted to a glass cover/superstrate, with coplanar back-side contacts. The coverglass is not prismatic. The CLEFT process, a method for mechanically separating epitaxial layers from their substrate, is used to process these cells into thin films. The advantages of single-crystal GaAs are thereby retained, while reducing weight and cutting cost by allowing for substrate reuse. Thin-film cells also have better thermal management capabilities and can be stacked for use in tandem structures. Cell fabrication and performance are described, and directions for further improvements are identified.

Dingle, B. D.↗

NASA NTRS1991

Selective and low temperature synthesis of polycrystalline diamond

Polycrystalline diamond thin films have been deposited on single-crystal silicon substrates at low temperatures (not above 600 C) using a mixture of hydrogen and methane gases by high-pressure microwave plasma-assisted chemical vapor deposition. Low-temperature deposition has been achieved by cooling the substrate holder with nitrogen gas. For deposition at reduced substrate temperature, it has been found that nucleation of diamond will not occur unless the methane/hydrogen ratio is increased significantly from its value at higher substrate temperature. Selective deposition of polycrystalline diamond thin films has been achieved at 600 C. Decrease in the diamond particle size and growth rate and an increase in surface smoothness have been observed with decreasing substrate temperature during the growth of thin films. As-deposited films are identified by Raman spectroscopy, and the morphology is analyzed by scanning electron microscopy.

Ramesham, R.↗

NASA NTRS1991

Controlled growth of 3C-SiC and 6H-SiC films on low-tilt-angle vicinal (0001) 6H-SiC wafers

It has been found that, with proper pregrowth surface treatment, 6H-SiC single-crystal films can be grown by chemical vapor deposition (CVD) at 1450 C on vicinal (0001) 6H-SiC with tilt angles as small as 0.1 deg. Previously, tilt angles of greater than 1.5 deg were required to achieve 6H on 6H at this growth temperature. In addition, 3C-SiC could be induced to grow within selected regions on the 6H substrate. the 3C regions contained few (or zero) double-positioning boundaries and a low density of stacking faults. A new growth model is proposed to explain the control of SiC polytype in this epitaxial film growth process.

Powell, J. A.↗

NASA NTRS1991

Application of Oxidation to the Structural Characterization of Sic Epitaxial Films

Both 3C-SiC and 6H-SiC single-crystal films can be grown on vicinal (0001) 6H-SiC wafers. It is found that oxidation can be a powerful diagnostic process for (1) 'color mapping' the 3C and 6H regions of these films, (2) decorating stacking faults in the films, (3) enhancing the decoration of double positioning boundaries, and (4) decorating polishing damage. Contrary to previously published oxidation results, proper oxidation conditions can yield interference colors that provide a definitive map of the polytype distribution for both the Si face and C face of SiC films.

Powell, J. A.↗

NASA NTRS1991

Fracture of single crystals of the nickel-base superalloy PWA 1480E in hydrogen at 22 C

The present study investigates the hydrogen-induced fracture behavior of notched single crystals of the PWA 1480E nickel-based superalloy. Notched single crystals with seven different crystal orientations were tensile tested at 22 C in a hydrogen atmosphere at 34 MPa. Hydrogen-enhanced cleavage along 100-line planes in the notched region was found to be due to cracking along the gamma/gamma-prime interfaces. Cleavage on 111-line-type planes was observed only outside the notch region. The occurrence of 100- and 111-line-types of cleavage was independent of the single-crystal orientation. Outside the notch region, the fracture surfaces of specimens tested in hydrogen appeared very similar to those tested in helium. Differences in the fracture surfaces were located primarily near the notch region.

Chen, P. S.↗

NASA NTRS1991

High-voltage 6H-SiC p-n junction diodes

A chemical vapor deposition (CVD) process has been used to produce device structures of n- and p-type 6H-SiC epitaxial layers on commercially produced single-crystal 6H-SiC wafers. Mesa-style p-n junction diodes were successfully fabricated from these device structures using reactive ion etching, oxide passivation, and electrical contact metallization techniques. When tested in air, the 6H-SiC diodes displayed excellent rectification characteristics up to the highest temperature tested, 600 C. To observe avalanche breakdown of the p-n junction diodes, testing under a high-electrical-strength liquid was necessary. The avalanche breakdown voltage was 1000 V representing the highest reverse breakdown voltage to be reported for any CVD-grown SiC diode.

Matus, L. G.↗

NASA NTRS1991

Controllable surface-plasmon resonance in engineered nanometer epitaxial silicide particles embedded in silicon

Epitaxial CoSi2 particles in a single-crystal silicon matrix are grown by molecular-beam epitaxy using a technique that allows nanometer control over particle size in three dimensions. These composite layers exhibit resonant absorption predicted by effective-medium theory. Selection of the height and diameter of disklike particles through a choice of growth conditions allows tailoring of the depolarization factor and hence of the surface-plasmon resonance energy. Resonant absorption from 0.49 to 1.04 eV (2.5 to 1.2 micron) is demonstrated and shown to agree well with values predicted by the Garnett (1904, 1906) theory using the bulk dielectric constants for CoSi2 and Si.

Fathauer, R. W.↗

NASA NTRS1990

Dissociation of O(2-)2 defects into paramagnetic O(-) in wide band-gap insulators - A magnetic susceptibility study of magnesium oxide

The magnetic susceptibility of single-crystal MgO has been measured in the temperature range 300-1000 K, using a Faraday balance. The high-purity crystal (less than 100 ppm transition metals), grown from the melt in a H2O-containing atmosphere, was found to be paramagnetic due to the presence of defects on the O(2-) sublattice. The defects derive from OH(-) introduced into the MgO matrix by the dissolution of traces of H2O during crystal growth. The OH(-) converts into O(2-)2 and H2. Each O(2-)2 represents two coupled, spin-paired O(-) states. The observed strongly temperature-dependent paramagnetism can be described by three contributions that overlay the intrinsic diamagnetism of MgO and arise from the low level of transition-metal impurities, O(-) generated by 0(2-)2 dissociation, and O(-) states trapped by quenching from high temperatures from previous experiments.

Batllo, F.↗

NASA NTRS1992

A viscoplastic theory for anisotropic materials

The purpose of this work is the development of a unified, cyclic, viscoplastic model for anisotropic materials. The first part of the paper presents the foundations of the model in the framework of thermodynamics with internal variables. The second part considers the particular case of cubic symmetry, and addresses the cyclic behavior of a nickel-base single-crystal superalloy, CMSX-2, at high temperature (950 C).

Nouailhas, D.↗

NASA NTRS1991

Growth of Sr(0.61)Ba(0.39)Nb2O6 fibers - New results regarding orientation

The paper describes stable growth of Sr(0.61)Ba(0.39)Nb2O6 (SBN) single-crystal optical fibers (grown by the laser-heated pedestal growth method) along the 100-line and 110-line crystallographic axes. The orientation of SBN fibers was investigated using transmission holograms recorded by focusing two separate, but mutually coherent, optical wavefronts into one end of the fiber. Results showed that the crystal quality of 100-line and 110-line SBN fibers grown at a given pull velocity strongly depended on the fiber diameter; generally, the quality improves with decreasing diameter.

Wilde, Jeffrey P.↗

NASA NTRS1992

Melting of the Abrikosov flux lattice in anisotropic superconductors

It has been proposed that the Abrikosov flux lattice in high-Tc superconductors is melted over a significant fraction of the phase diagram. A thermodynamic argument is provided which establishes that the angular dependence of the melting temperature is controlled by the superconducting mass anisotropy. Using a low-frequency torsional-oscillator technique, this relationship has been tested in untwinned single-crystal YBa2Cu3O(7-delta). The results offer decisive support for the melting proposal.

Beck, R. G.↗

NASA NTRS1992

Microstructural investigations of light-emitting porous Si layers

The structural and morphological characteristics of visible-light-emitting porous Si layers produced by anodic and stain etching of single-crystal Si substrates are compared using transmission electron microscopy and atomic force microscopy (AFM). AFM of conventionally anodized, laterally anodized and stain-etched Si layers show that the layers have a fractal-type surface morphology. The anodized layers are rougher than the stain-etched films. At higher magnification 10 nm sized hillocks are visible on the surface. Transmission electron diffraction patterns indicate an amorphous structure with no evidence for the presence of crystalline Si in the near-surface regions of the porous Si layers.

George, T.↗

NASA NTRS1991

Silicon carbide, a semiconductor for space power electronics

After many years of promise as a high temperature semiconductor, silicon carbide (SiC) is finally emerging as a useful electronic material. Recent significant progress that has led to this emergence has been in the area of crystal growth and device fabrication technology. High quality of single-crystal SiC wafers, up to 25 mm in diameter, can now be produced routinely from boules grown by a high temperature (2700 K) sublimation process. Device fabrication processes, including chemical vapor deposition (CVD), in situ doping during CVD, reactive ion etching, oxidation, metallization, etc. have been used to fabricate p-n junction diodes and MOSFETs. The diode was operated to 870 K and the MOSFET to 770 K.

Powell, J. A.↗

NASA NTRS1992

Growth parameters affecting the formation of buried CoSi2 by endotaxy of Co on Si(111)

At growth temperatures of roughly 800 C, Co deposited on Si (111 ) diffuses through a Si capping layer and exhibits oriented growth on buried CoSi2 seeds, a process referred to as endotaxy. This occurs preferentially to surface nucleation of CoSi2 under certain growth conditions. High-quality continuous single-crystal buried silicide layers have been obtained by endotaxy. This requires very low densities of attractive nucleation sites other than the buried seeds. For this reason, use of a silicon buffer layer and a low base pressure in the molecular-beam epitaxy system are found to be essential. Growth conditions required for high-quality layers and problems which result from growth outside these limits are discussed.

Fathauer, R. W.↗