Search NASA⌕ Search

SEARCH · Search NASA

Results for “solvent change”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Toward Computation-Guided Design of Tunable Organic-Inorganic CdS Quantum Dot Binary Superlattices

Combining the advantages of structural programmability in sequence-defined biomimetic molecules and the controllable packing geometry in nanoparticle superlattices, we demonstrate a self-assembled organic-inorganic superlattice whose structure can be altered with the slightest change in the sequence of the organic counterpart. Here, oleate-coated CdS quantum dots (QDs) form a square-packed superlattice with a 1:1 molar equivalence of a di-block amphiphilic peptoid (Nbrpe6Dig) in chloroform. In contrast, no apparent structure is observed in the organic solvent alone. Based on theoretical evidence, we show that the assembly is a binary superlattice where both the CdS QDs and the peptoids serve as building blocks and further predict a correlation between the superlattice structure and the peptoid sequence. The computationally guided prediction is validated by experiments where superlattice transformation is observed with modified peptoids. The mechanism identified in our work inspires new ways to control and tune organic-inorganic hybrid nanomaterial self-assembly.

Qi, Xin↗
DOE OSTI2023

Investigation of the effects of ternary deep eutectic solvent composition on pretreatment of sorghum stover

Biomass‐derived deep eutectic solvents (DESs) have been introduced as promising pretreatment and fractionation solvents because of their mild processing conditions, easy synthesis, and green solvent components from biomass. In recent DES studies, solvent‐based third constituents like water, ethanol, and others improve the processibility of typical binary DESs. However, the impacts of these components are not well understood. Here, two solvent‐based constituents, including water and ethylene glycol, were applied to 3,4‐dihydroxybenzoic acid (DHBA)‐based DES system for improving the conversion efficiency of cellulose‐rich fraction and the properties of lignin fraction. Chemical composition, enzymatic digestibility, degree of polymerization of cellulose and physicochemical properties of lignin were used to evaluate the impact of each third constituent on biomass processing. Ternary ChCl‐DHBA DESs exhibited better performances in delignification, fermentable sugar production, and preservation of β‐O‐4 ether linkage in lignin compared with binary ChCl‐DHBA DES.

09 BIOMASS FUELS↗
DOE OSTI2020

First-principle investigation on catalytic hydrogenation of benzaldehyde over Pt-group metals

We report that understanding the hydrogenation of organic compounds in the aqueous phase has always been fundamentally important for improving carbon neutral pathways to fuels and value-added chemicals. In this study, we investigated both thermodynamic and kinetic profiles of benzaldehyde hydrogenation over the Pd(111) and Pt(111) metal surfaces using density functional theory (DFT) and ab initio molecular dynamic (AIMD) simulations. The adsorption of H 2 shows the mixed preference of H adsorption sites on the Pt(111), while the fcc adsorption site is dominant for H on the Pd(111). When benzaldehyde is added to the systems, we observe a strong reduction of benzaldehyde on charged Pd (111) surface compared with that on neutral surface. In contrast, charged state of the Pt(111) surface does not change their interaction. Subsequent hydrogenation reaction of benzaldehyde over Pd(111), proceeding via Langmuir-Hinshelwood mechanism, is affected by two major factors: the presence of H 2 O solvent and surface charge. The presence of H 2 O solvent greatly reduces the activation energy of C-H and O-H bond formation during the hydrogenation process. Furthermore, the hydrogenation step via C-H bond formation is preferred thermodynamically and kinetically over O-H bond formation during thermocatalytic hydrogenation, while the opposite trend holds true during electrocatalytic hydrogenation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Decoding the Effect of Anion Identity on the Solubility of N -(2-(2-Methoxyethoxy)ethyl)phenothiazine (MEEPT)

Variations in the solubility of redox-active organic molecules (ROM) of interest for nonaqueous redox flow batteries (RFB), especially as the ROM state-of-charge changes during charge-discharge cycling, present significant molecular design challenges. The situation is further complicated as ROM solubility can be regulated by the choice of electrolyte salt and solvent that together with the ROM comprise the catholyte or anolyte (redox electrolyte) formulation, presenting materials design challenges. The ROM N-(2-(2-methoxyethoxy)ethyl)phenothiazine (MEEPT) is a viscous liquid at room temperature and is miscible in several organic solvents, including acetonitrile and propylene carbonate. The MEEPT radical cation (MEEPT +· ) paired with tetrafluoroborate (BF 4 - ) in acetonitrile presents a 0.5 M solubility, a dramatic decrease when compared to the viscous liquid of neutral MEEPT. Here, in this study, we present a joint experimental, regression modeling, and molecular dynamics (MD) simulations investigation to explore MEEPT-X (where X represents the counteranion) salt solubility variability as a function of concentration and counteranion chemistry in acetonitrile. We find a strong dependence of the salt solubility on the counteranion and relate these findings to explicit intermolecular interactions between MEEPT +· and the counteranion in the electrolyte solution.

Perera, Anton S. [Univ. of Kentucky, Lexington, KY↗
NASA NTRS2008

Sensing a Changing Chemical Mixture Using an Electronic Nose

A method of using an electronic nose to detect an airborne mixture of known chemical compounds and measure the temporally varying concentrations of the individual compounds is undergoing development. In a typical intended application, the method would be used to monitor the air in an inhabited space (e.g., the interior of a building) for the release of solvents, toxic fumes, and other compounds that are regarded as contaminants. At the present state of development, the method affords a capability for identifying and quantitating one or two compounds that are members of a set of some number (typically of the order of a dozen) known compounds. In principle, the method could be extended to enable monitoring of more than two compounds. An electronic nose consists of an array of sensors, typically made from polymer carbon composites, the electrical resistances of which change upon exposure to a variety of chemicals. By design, each sensor is unique in its responses to these chemicals: some or all of the sensitivities of a given sensor to the various vapors differ from the corresponding sensitivities of other sensors. In general, the responses of the sensors are nonlinear functions of the concentrations of the chemicals. Hence, mathematically, the monitoring problem is to solve the set of time-dependent nonlinear equations for the sensor responses to obtain the time dependent concentrations of individual compounds. In the present developmental method, successive approximations of the solution are generated by a learning algorithm based on independent-component analysis (ICA) an established information theoretic approach for transforming a vector of observed interdependent signals into a set of signals that are as nearly statistically independent as possible.

Duong, Tuan↗
DOE OSTI2023

One-pot generation of lignin microspheres and digestible substrate with a polyol-DES pretreatment in high solid loading

Previous lignin microspheres (LMS) preparation needs multiple steps with very low yield and high cost. Herein, we developed a high-solid deep eutectic solvent (DES) pretreatment for an effective lignin fractionation and enzymatic saccharification of moso bamboo under mild temperature (110 °C) with high-solid loading. Lignin was significantly removed from the plant cell wall, and cellulose properties (e.g., crystallinity and degree of polymerization) were also altered during the pretreatment. As a result, the enzymatic digestibility of the pretreated bamboo was dramatically increased. Uniform micro-spherical lignin was directly produced from the pretreatment system, and its particle size could be regulated by controlling the solid loadings and pretreatment temperatures. The lignin microspheres formation mechanism was investigated by analyzing the lignin's size distribution, molecular weight distribution, chemical structure, and hydrophobicity. The DES showed excellent recyclability, and the recycled DES could still remove 42.78% lignin even after 7th circulation associated with 100% glucan saccharification. Further, the mass balance based on 1000 g biomass showed that 196.28 g LMS was directly recovered, which exhibited a high RhB adsorption. Besides, 404.91 g glucose and 36.67 g xylose were obtained after the enzymatic saccharification process. Specifically, GAPI analysis exhibited a near total green and yellow portions of the pictogram, indicating our DES process was green enough to make this biorefinery sustainable. Overall, the proposed DES generated synergistic productions of digestible solid and LMS which could contribute to establish a green and sustainable biorefinery sequence with diverse outputs in one pot.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Evaluating the Structural Response of Amphiphilic Monolayers to Environmental Stimuli

Amphiphilic monolayers composed of end groups with distinct polar and nonpolar functional groups offer rapid and reversible interfacial adaptation in response to environmental stimuli such as a change in interfacial medium polarity. We have synthesized and characterized a suite of monolayers with functional groups of competing polarity designed to reconfigure their interfacial chemical composition in response to solvent polarity. In these films, the end group is designed to be able to reorient and expose the functional groups that minimize the interfacial free energy between the film and the environment. Using a combination of spectroscopic, computational, and wettability studies, we have investigated the responsive interfacial behavior of different end groups upon exposure to environments with varying polarities. Contact angle measurements across a series of polar and dispersive probe liquids reveal trends that reflect the underlying molecular flexibility and composition. Vibrational sum frequency generation (SFG) spectroscopy and atomistic molecular dynamics (MD) simulations confirm solvent-driven reorientation of the end groups, with restructuring observed at the interface. To quantify these effects, we have developed a surface energy calculation model that incorporates solvent-induced surface rearrangements into the estimations. Our findings reveal a strong dependence of surface energy and switching behavior on the length and flexibility of the functionalities in the end group, which affects the exposure of certain interfacial compositions under different solvents. These results offer new insights into the design of adaptive monolayers and provide a framework for evaluating solvent-responsive surfaces.

functional groups↗
NASA NTRS1989

Method of infusion extraction

Apparatus and method of removing desirable constituents from an infusible material by infusion extraction, where a piston operating in a first chamber draws a solvent into the first chamber where it may be heated, and then moves the heated solvent into a second chamber containing the infusible material, and where infusion extraction takes place. The piston then moves the solvent containing the extract through a filter into the first chamber, leaving the extraction residue in the second chamber.

Chang-Diaz, Franklin R.↗
NASA NTRS2006

Stability Enhancement of Polymeric Sensing Films Using Fillers

Experiments have shown the stability enhancement of polymeric sensing films on mixing the polymer with colloidal filler particles (submicron-sized) of carbon black, silver, titanium dioxide, and fumed silicon dioxide. The polymer films are candidates for potential use as sensing media in micro/nano chemical sensor devices. The need for stability enhancement of polymer sensing films arises because such films have been found to exhibit unpredictable changes in sensing activity over time, which could result in a possible failure of the sensor device. The changes in the physical properties of a polymer sensing film caused by the sorption of a target molecule can be measured by any of several established transduction techniques: electrochemical, optical, calorimetric, or piezoelectric, for example. The transduction technique used in the current polymer stability experiments is based on piezoelectric principles using a quartz-crystal microbalance (QCM). The surface of the QCM is coated with the polymer, and the mass uptake by the polymer film causes a change in the oscillating frequency of the quartz crystal. The polymer used for the current study is ethyl cellulose. The polymer/ polymer composite solutions were prepared in 1,3 dioxolane solvent. The filler concentration was fixed at 10 weight percent for the composites. The polymer or polymer composite solutions were cast on the quartz crystal having a fundamental frequency of about 6 MHz. The coated crystal was subjected to a multistage drying process to remove all measurable traces of the solvent. In each experiment, the frequency of oscillation was measured while the QCM was exposed to clean, dry, flowing air for about 30 minutes, then to air containing a known concentration of isopropanol for about 30 minutes, then again to clean dry air for about 30 minutes, and so forth. This cycle of measurements for varying isopropanol concentrations was repeated at intervals for several months. The figure depicts some of the sensing film stability results for ethyl cellulose polymer, ethyl cellulose-carbon black, and ethyl cellulose-silicon dioxide composite systems. An ethyl cellulose film exhibited a marked decline in response in the first few months of study and settled to a steady average response after about four months. However, response varied widely around the average response for ethyl cellulose film. In contrast, ethyl cellulose- carbon black and ethyl cellulose-silicon dioxide composites also declined in the early months, but showed more repeatable sensing film activity after the initial decline. Similar trends were observed in experiments for ethyl cellulose-titanium dioxide and ethyl cellulose-silver composites.

Lin, Brian↗
NASA NTRS1988

Infusion Extractor

Apparatus and method of removing desirable constituents from an infusible material by infusion extraction, where a piston operating in a first chamber draws a solvent into the first chamber where it may be heated, and then moves the heated solvent into a second chamber containing the infusible material, and where infusion extraction takes place. The piston then moves the solvent containing the extract through a filter into the first chamber, leaving the extraction residue in the second chamber.

Chang-Diaz, Franklin R.↗
NASA NTRS2017

One Step Plasma Passivation and Precision Cleaning

Over the past several years, Kennedy Space Center (KSC) researchers developed two solvent-free techniques for precision cleaning of ground support equipment (GSE) that possess low commodity requirements and produce small or no waste streams. During testing of low-pressure air plasma as one of these cleaning techniques, physical changes in the surface of stainless steel test pieces were observed; cursory testing revealed that the test part had developed a thick oxide layer on the surface compared to untreated parts. This result indicated that the plasma process might not only serve as a green technology for precision cleaning of parts, but it may also passivate the surface at the same time. Current methodology in use at KSC’s Components Refurbishment & Chemical Analysis (CRCA) Facility for passivation of corrosion-resistant steels for aerospace applications follows an SAE International Standard, AMS2700, where parts are submerged in either a nitric acid or nitric acid/sodium dichromate bath at predetermined temperatures and contact times. These baths require constant testing to ensure effective treatment, use corrosive and carcinogenic chemicals, and produce hazardous waste. The passivation bath is one of the multiple steps employed at the facility, while cleaning with multiple environmentally-unfriendly solvents comprise several more steps before parts are recertified to a specific cleanliness level in their clean room. Based on the behavior of the stainless steel surface during cleaning optimization studies, it was believed that the plasma technology could be extended to passivation, combining what is currently many steps into a single, solvent- and waste-free system.

Paul Hintze↗
DOE OSTI2023

Optical spectroscopy of molten fluorides: Methods, electronic and vibrational data, structural interpretation, and relevance to radiative heat transfer

In this study, to help address the need for predicting radiative heat transfer (RHT) behavior of molten salts, we conducted a comprehensive review of methods and data from optical spectroscopic measurements on molten fluoride salts. Transmittance, reflectance, and trans-reflectance experimental methods are discussed, along with the corresponding data reduction methodology and the limitations of each technique. Optical spectroscopy is a convenient indirect probe for changes in structural parameters with temperature and composition. Electronic and vibrational absorption data for transition-metal, lanthanide, and actinide solutes and vibrational absorption data for alkali and alkaline earth fluoride solvents are compiled, and the corresponding structural interpretation is discussed and compared with other experimental and theoretical work. We find that solvent and solute vibrational absorption can be significant in the mid-infrared, resulting in near-infrared edges of significance to RHT. Extrapolation and averaging of existing edge data leads to estimated gray absorption coefficient values at 700 °C of 546 m —1 for FLiBe and 276 m —1 for FLiNaK, both within the range of 1 – 6000 m —1 identified to be of engineering relevance for radiative heat transfer analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Progress Towards Extended Cycle Life Si-based Anodes: Investigation of Fluorinated Local High Concentration Electrolytes

Silicon (Si) anodes are promising candidates for Li-ion batteries due to their high specific capacity and low operating potential. Implementation has been challenged by the significant Si volume changes during (de)lithiation and associated growth/regrowth of the solid electrolyte interphase (SEI). In this report, fluorinated local high concentration electrolytes (FLHCEs) were designed such that each component of the electrolyte (solvent, salt, diluent) is fluorinated to modify the chemistry and stabilize the SEI of high (30%) silicon content anodes. FLHCEs were formulated to probe the electrolyte salt concentration and ratio of the fluorinated carbonate solvents to a hydrofluoroether diluent. Higher salt concentrations led to higher viscosities, conductivities, and contact angles on polyethylene separators. Electrochemical cycling of Si-graphite/NMC622 pouch cells using the FLHCEs delivered up to 67% capacity retention after 100 cycles at a C/3 rate. Post-cycling X-ray photoelectron spectroscopy (XPS) analyses of the Si-graphite anodes indicated the FLHCEs formed a LiF rich solid electrolyte interphase (SEI). The findings show that the fluorinated local high concentration electrolytes contribute to stabilizing the Si-graphite electrode over extended cycling.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Resistance to outflow of cerebrospinal fluid after central infusions of angiotensin

Infusions of artificial cerebrospinal fluid (CSF) into the cerebroventricles of conscious rats can raise CSF pressure (CSFp). This response can be modified by some neuropeptides. One of these, angiotensin, facilitates the rise in CSFp. We measured CSFp in conscious rats with a computerized system and evaluated resistance to CSF outflow during infusion of artificial CSF, with or without angiotensin, from the decay kinetics of superimposed bolus injections. Angiotensin (10 ng/min) raised CSFp (P less than 0.05) compared with solvent, but the resistance to CSF outflow of the two groups was similar (P greater than 0.05). Because CSFp was increased by angiotensin without an increase in the outflow resistance, a change in some volume compartment is likely. Angiotensin may raise CSFp by increasing CSF synthesis; this possibility is supported, since the choroid plexuses contain an intrinsic isorenin-angiotensin system. Alternatively, angiotensin may dilate pial arteries, leading to an increased intracranial blood volume.

NASA Discipline Cardiopulmonary↗
DOE OSTI2021

Specific Ion Solvation and Pairing Effects in Glycerol Carbonate

Identifying the driving forces behind the solvation of inorganic salts by nonaqueous solvents is an important step in the development of green solvents. Here we focus on one promising solvent: glycerol carbonate (GC). Using ab initio molecular dynamics simulations, we build upon our previous work by detailing glycerol carbonate’s interactions with a series of anions, a lithium ion, and the LiF ion pair. Through these investigations, we highlight the changes in solvation behavior as the anion size increases, the competition of binding shown by lithium for the oxygens of GC, and the behavior of the LiF ion pair in a GC solution. These results in this work indicate the importance of the cation’s identity in ion-pairing structure and dynamics and lend insight into the key factors behind the specific ion effects seen in GC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Role of a Multivalent Ion–Solvent Interaction on Restricted Mg 2+ Diffusion in Dimethoxyethane Electrolytes

The diffusion behavior of Mg 2+ in electrolytes is not as readily accessible as that from Li + or Na + utilizing PFG NMR, due to the low sensitivity, poor resolution, and rapid relaxation encountered when attempting 25 Mg NMR. In MgTFSI 2 /DME solutions, “bound” DME (coordinating to Mg 2+ ) and “free” DME (bulk) are distinguishable from 1 H NMR. With the exchange rates between them obtained from 2D 1 H EXSY NMR, we can extract the self-diffusivities of free DME and bound DME (which are equal to that of Mg 2+ ) before the exchange occurs using PFG diffusion NMR measurements coupled with analytical formulas describing diffusion under two-site exchange. Further, the high activation enthalpy for exhange (65–70 kJ/mol) can be explained by the structural change of bound DME as evidenced by its reduced C–H bond length. Comparison of the diffusion behaviors of Mg 2+ , TFSI – , DME, and Li + reveals a relative restriction to Mg 2+ diffusion that is caused by the long-range interaction between Mg 2+ and solvent molecules, especially those with suppressed motions at high concentrations and low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Durable and Versatile Immobilized Carbonic Anhydrase on Textile Structured Packing for CO 2 Capture

High-performance carbon dioxide (CO 2 )-capture technologies with low environmental impact are necessary to combat the current climate change crisis. Durable and versatile “drop-in-ready” textile structured packings with covalently immobilized carbonic anhydrase (CA) were created as efficient, easy to handle catalysts for CO 2 absorption in benign solvents. The hydrophilic textile structure itself contributed high surface area and superior liquid transport properties to promote gas-liquid reactions that were further enhanced by the presence of CA, leading to excellent CO 2 absorption efficiencies in lab-scale tests. Mechanistic investigations revealed that CO 2 capture efficiency depended primarily on immobilized enzymes at or near the surface, whereas polymer entrapped enzymes were more protected from external stressors than those exposed at the surface, providing strategies to optimize performance and durability. Textile packing with covalently attached enzyme aggregates retained 100% of the initial 66.7% CO 2 capture efficiency over 71-day longevity testing and retained 85% of the initial capture efficiency after 1-year of ambient dry storage. Subsequent stable performance in a 500 h continuous liquid flow scrubber test emphasized the material robustness. Biocatalytic textile packings performed well with different desirable solvents and across wide CO 2 concentration ranges that are critical for CO 2 capture from coal and natural gas-fired power plants, from natural gas and biogas for fuel upgrading, and directly from air.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗