Results for “specific energy” — Page 19

NASA NTRSDate not supplied

Crash Sled Testing of Triaxially-Braided CFRP for Improved Vehicular Crashworthiness

The Impact Dynamics Laboratory at NASA Glenn Research Center recently developed a pneumatically-actuated crash sled for investigating the crush behavior of structural elements for vehicular applications. The apparatus includes an adjustable striker mass and specimen support mass, which are mounted on separate rails. This setup provides two advantages over crash sleds with so-called fixed specimen supports: (i) it allows for multiple independent measurements of the crush response using different instruments, and (ii) the specimen support can be varied and its reaction can be explicitly measured. This paper describes the experimental setup and data analysis methodology and illustrates the capability of the sled for measuring the specific energy absorption (SEA) of triaxially-braided carbon/epoxy composite C-channels and corrugated plates. The corrugated plate had a higher SEA than the C-channel and the SEAs did not vary when the striker mass and velocity were changed so that incident energy was constant.

Energy absorption↗

NASA NTRS2021

Parametric Study of State-of-Charge for an Electric Aircraft in Urban Air Mobility

The envisioned concept of urban air mobility is anticipated to support passenger transportation, cargo delivery, and emergency services in major metropolitan areas with increasing autonomy levels in the future. Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. However, the low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, to enable autonomous urban air mobility operations using electric aircraft, one of the critical steps from a safety and efficiency perspective is to understand how various operational and environmental conditions impact the state-of-charge of the onboard lithium-ion polymer batteries. This research performs a parametric study of the state-of-charge for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The parameters considered for the parametric analysis are cruise airspeed, cruise altitude, climb and descent profiles, wind conditions (wind magnitude, wind direction relative to the route, and wind magnitude uncertainty), and required time of arrival.

Urban Air Mobility↗

NASA NTRS2021

Parametric Study of State of Charge for an Electric Aircraft in Urban Air Mobility

The envisioned concept of urban air mobility is anticipated to support passenger transportation, cargo delivery, and emergency services in major metropolitan areas with increasing autonomy levels in the future. Distributed electric propulsion powered electric vertical takeoff and landing aircraft are expected to enable urban air mobility. However, the low specific energy of onboard lithium-ion polymer batteries and wind conditions impose constraints on flight endurance. Therefore, to enable autonomous urban air mobility operations using electric aircraft, one of the critical steps from a safety and efficiency perspective is to understand how various operational and environmental conditions impact the state-of-charge of the onboard lithium-ion polymer batteries. This research performs a parametric study of the state-of-charge for a NASA-proposed conceptual multirotor aircraft flight in the urban environment. The parameters considered for the parametric analysis are cruise airspeed, cruise altitude, climb and descent profiles, wind conditions (wind magnitude, wind direction relative to the route, and wind magnitude uncertainty), and required time of arrival.

Urban Air Mobility↗

NASA NTRSDate not supplied

Continued Exploration of the Electrified Aircraft Propulsion Design Space

A previous electrified aircraft propulsion (EAP) design space exploration study was continued to investigate the impact of mission constraints, further explore the design space of different sized aircraft, and improve the modeling process. Three aircraft were investigated, 18- and 48-passenger turboprops, and a 78-passenger turbofan. Baseline aircraft models were inherited from the earlier study and were hybridized by applying EAP technologies. A parametric study varying motor power and battery specific energy was conducted. For the 78-passenger turbofan, design range was also introduced as a parametric parameter. Key metrics for the study included equivalent lifecycle CO2 emissions and direct operating cost plus interest. Both turboprop aircraft demonstrated significant potential savings in block fuel consumption and CO2 emissions, but at increased operating costs compared to their baseline models. As the 78-passenger turbofan had shown no improvements in any metrics under reasonable technology assumptions, design range was shortened in an attempt to obtain performance benefits. When designed for a shorter range, the 78-passenger EAP vehicle showed potential improvements in block fuel when compared to a baseline with a similarly shortened design range, but not in any other metrics. Operating cost reductions were not achieved for any aircraft, but several designs came close to breaking even with their baselines. Smaller, shorter range aircraft and turboprops demonstrated larger performance benefits and smaller operating cost penalties, but a simple trade of electric energy storage in batteries for fuel is generally insufficient to produce a viable aircraft concept.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Development and Application of a Novel Calorimetry Technique for the Study of Lithium-Ion Cell Thermal Runaway

Lithium-ion battery technology is widely used and is attractive due to demonstrated specific energies in the 200-300 W-hr/kg range. The excellent, mass-efficient energy storage capability of lithium-ion batteries has led to their use on many aerospace platforms. However, lithium-ion batteries can exhibit thermal runaway behavior wherein stored electrochemical energy is released rapidly as a result of thermal or mechanical failure, electrochemical abuse, internal or external short circuiting. A single cell undergoing thermal runaway within a battery has the potential to induce thermal runaway in adjacent cells if heat dissipation is not properly managed and can result in a catastrophic failure of the battery. Designing batteries that are resistant to thermal runaway propagation requires an understanding of, not only, total energy yield but also the means by which that energy is liberated from the cell. While Accelerating Rate Calorimetry and other techniques provide total thermal runaway energy yield, they do not provide the fractional breakdown of energy liberated via conduction through the cell casing from that which is vented from the cell as hot gases and effluents. Such data are needed to inform battery thermal design and analysis. To measure the total energy yield, the fraction conducted through the cell casing, and the fraction lost due to gases and effluents, NASA developed Fractional Thermal Runaway Calorimetry (FTRC). Two calorimeters have been developed and demonstrated, the Small-format- and Large-format Fractional Thermal Runaway Calorimeters (S-FTRC and L-FTRC, respectively). The technique has been successfully applied to small- and large-format cells (2.4-3.5 Ah and >100 Ah capacity, respectively) and has given new insights into Li-ion cell thermal runaway. Development of the calorimeters is discussed and results from the initial thermal runaway testing campaigns are presented.

Lithium-Ion Cell↗

NASA NTRS2023

Exploration of Design Drivers for the RVLT Lift+Cruise Reference Aircraft

A trade study was performed on an all-electric version of the Lift+Cruise urban air mobility reference aircraft developed under the Revolutionary Vertical Lift Technology Project. The trade study varied the input parameters of mission range, takeoff altitude, mission reserve time, cell specific energy, disk loading, and payload weight. A step-by-step incremental change in the input parameters was also examined. Analyses were performed using the NASA Design and Analysis of Rotorcraft tool and a Rapid Sizing Tool for electric vertical takeoff and landing aircraft. A comparison of the analysis results between the two tools shows good agreement in trends with differences in slope. Overall, the analysis shows that the Lift+Cruise configuration performs poorly on a NASA-defined, energy-dominated mission due to poor aerodynamic efficiency in forward flight. This poor cruise-flight efficiency results in a large energy requirement, which increases the required battery sizing and corresponding aircraft gross weight. As such, continued conceptual design and refinement of the Lift+Cruise reference aircraft by the RVLT Concepts Team will likely be limited.

UAM↗

NASA NTRSDate not supplied

Feasibility Study of an All-Electric 150 Passenger Aircraft

Among the potential future technologies for low-carbon transport aircraft, all-electric concepts stand out environmentally, yet their feasibility and cost-effectiveness at scale remain uncertain. This paper examines the conceptual design of an all-electric 150-passenger aircraft with a range of 840 NM based on assumed future battery cell-level specific energy of1620Wh/kg. The tube and wing design is propelled by open rotors driven by four electric motors per nacelle and utilizes advanced structural materials for weight reduction. Powertrain technology gaps are identified. The conceptual design shows that all-electric aviation could supplant about 30% of current fossil fuel use by transport aircraft and potentially more with air-traffic-control modifications.

electric aircraft↗

NASA NTRSDate not supplied

A Prognostics Framework for Battery Health Monitoring Integrated with Thermal Modeling

Urban Air Mobility (UAM) promises to revolutionize transportation in major cities, offering passenger travel, cargo delivery, and emergency medical services through a network of electric vertical takeoff and landing (eVTOL) aircraft. However, the limited range of current eVTOLs, due to the low specific energy of lithium-ion batteries along with a possibility of thermal runaway conditions poses significant safety concerns, leading to potentially compromising operational safety. To address this critical challenge, researchers are actively evaluating the impact of flight and environmental conditions on onboard lithium-ion battery health. This involves carefully assessing the performance of battery packs under laboratory and operational conditions for developing models to estimate future health using prognostics framework. This study examines the effectiveness of evaluating battery degradation leading to catastrophic failures under varying operational conditions in laboratory. These are captured using physics based models of underlying phenomenons and integrated into the prognostics framework. A fully charged battery undergoes controlled discharge cycles at varying C-rates based on the simulated power draw profile, with current and voltage, temperature data recorded throughout the experiment. The observed data provides valuable insights into how different operating conditions and mission profiles affect battery performance. This information is crucial for developing strategies to optimize battery systems, enhance range, and ultimately ensure the safe and reliable operation of UAM vehicles.

Thermal Modeling↗

NASA NTRSDate not supplied

A Prognostics Framework for Battery Health Monitoring Integrated with Thermal Modeling

Urban Air Mobility (UAM) promises to revolutionize transportation in major cities, offering passenger travel, cargo delivery, and emergency medical services through a network of electric vertical takeoff and landing (eVTOL) aircraft. However, the limited range of current eVTOLs, due to the low specific energy of lithium-ion batteries along with a possibility of thermal runaway conditions poses significant safety concerns, leading to potentially compromising operational safety. To address this critical challenge, researchers are actively evaluating the impact of flight and environmental conditions on onboard lithium-ion battery health. This involves carefully assessing the performance of battery packs under laboratory and operational conditions for developing models to estimate future health using prognostics framework. This study examines the effectiveness of evaluating battery degradation leading to catastrophic failures under varying operational conditions in laboratory. These are captured using physics based models of underlying phenomenons and integrated into the prognostics framework. A fully charged battery undergoes controlled discharge cycles at varying C-rates based on the simulated power draw profile, with current and voltage, temperature data recorded throughout the experiment. The observed data provides valuable insights into how different operating conditions and mission profiles affect battery performance. This information is crucial for developing strategies to optimize battery systems, enhance range, and ultimately ensure the safe and reliable operation of UAM vehicles.

Thermal Modeling↗

NASA NTRSDate not supplied

A Prognostics Framework for Battery Health Monitoring Integrated with Thermal Modeling

Urban Air Mobility (UAM) promises to revolutionize transportation in major cities, offering passenger travel, cargo delivery, and emergency medical services through a network of electric vertical takeoff and landing (eVTOL) aircraft. However, the limited range of current eVTOLs, due to the low specific energy of lithium-ion batteries along with a possibility of thermal runaway conditions poses significant safety concerns, leading to potentially compromising operational safety. To address this critical challenge, researchers are actively evaluating the impact of flight and environmental conditions on onboard lithium-ion battery health. This involves carefully assessing the performance of battery packs under laboratory and operational conditions for developing models to estimate future health using prognostics framework. This study examines the effectiveness of evaluating battery degradation leading to catastrophic failures under varying operational conditions in laboratory. These are captured using physics based models of underlying phenomenons and integrated into the prognostics framework. A fully charged battery undergoes controlled discharge cycles at varying C-rates based on the simulated power draw profile, with current and voltage, temperature data recorded throughout the experiment. The observed data provides valuable insights into how different operating conditions and mission profiles affect battery performance. This information is crucial for developing strategies to optimize battery systems, enhance range, and ultimately ensure the safe and reliable operation of UAM vehicles.

Thermal Modeling↗

NASA NTRSDate not supplied

Experimental Calibration of Flow Rule Coefficients for LS-Dyna Mat_213

Composite materials have become a popular choice in aerospace engineering applications due to their low weight, high specific stiffness, high specific energy absorption, and economic synthesis. As use of composite materials has proliferated, the need for accurate simulation under extreme loading conditions is of increasing importance. *MAT_213 is a tabulated plasticity and damage material model in LS-DYNA designed for such use cases. To account for the nonlinear material response, a plasticity algorithm is used, which employs a non-associative flow rule with coefficients requiring experimental calibration. This work outlines an experimental methodology for calibrating these coefficients using the macroscopic stress-strain response and microscopic in-plane strain measurements from coupon scale experiments. The model material used for the development and demonstration of this methodology is a plain weave woven fabric with T300 carbon fiber tows in the warp direction and Kevlar© 49 fiber tows in the weft direction, and an Epon© 828/Epikure© 3223 thermoset epoxy matrix. Coupon-scale tensile testing performed at multiple fiber angles (carbon fibers oriented 0º, 22.5º, 45º, 67.5º, and 90º relative to the loading axis) provides data for multiple calibration processes. The measured plastic strain increments in the principal material coordinate are used to set limits for ratios between flow rule coefficients. The identified ranges are used to bound the search for a set of coefficients, leading to convergence of different coupon responses in the effective stress – effective plastic strain space. Flow rule coefficients found by this methodology are then used as (i) input for LS-DYNA simulations of uniaxial tension coupon tests at varying fiber angles, and (ii) comparison of predicted values for the plastic Poisson’s ratio in global coordinates with the experimentally measured one for all off-axis orientations. These results are quantitatively and qualitatively compared to macroscopic stress-strain curves and experimental strain components. The conformity of the experimentally measured quantities with those derived from the simulations provide a means for assessing the quality of calibrated coefficients.

Polymer Matrix Composites↗

NASA NTRS2010

The Effect of Magnetohydrodynamic (MHD) Energy Bypass on Specific Thrust for a Supersonic Turbojet Engine

This paper describes the preliminary results of a thermodynamic cycle analysis of a supersonic turbojet engine with a magnetohydrodynamic (MHD) energy bypass system that explores a wide range of MHD enthalpy extraction parameters. Through the analysis described here, it is shown that applying a magnetic field to a flow path in the Mach 2.0 to 3.5 range can increase the specific thrust of the turbojet engine up to as much as 420 N/(kg/s) provided that the magnitude of the magnetic field is in the range of 1 to 5 Tesla. The MHD energy bypass can also increase the operating Mach number range for a supersonic turbojet engine into the hypersonic flight regime. In this case, the Mach number range is shown to be extended to Mach 7.0.

Benyo, Theresa L.↗

NASA NTRS1973

The effects of plasticity in adhesive fracture

An energy-balance analysis is presented for adhesive failure in end loaded cantilever beams. The analysis includes the effects of input work, stored strain energy, dissipated plastic energy, and specific adhesive surface energy. Experimental results obtained with 6061-T6 aluminum are presented as evidence for the validity of the approach.-

Chang, M. D.↗

NASA NTRS2013

Direct Energy Conversion for Low Specific Mass In-Space Power and Propulsion

"Changing the game" in space exploration involves changing the paradigm for the human exploration of the Solar System, e.g, changing the human exploration of Mars from a three-year epic event to an annual expedition. For the purposes of this assessment an "annual expedition" capability is defined as an in-space power & propulsion system which, with launch mass limits as defined in NASA s Mars Architecture 5.0, enables sending a crew to Mars and returning them after a 30-day surface stay within one year, irrespective of planetary alignment. In this work the authors intend to show that obtaining this capability requires the development of an in-space power & propulsion system with an end-to-end specific mass considerably less than 3 kg/kWe. A first order energy balance analysis reveals that the technologies required to create a system with this specific mass include direct energy conversion and nuclear sources that release energy in the form of charged particle beams. This paper lays out this first order approximation and details these conclusions.

Scott, John H.↗

NASA NTRS1976

The 727 approach energy management system avionics specification (preliminary)

Hardware and software requirements for an Approach Energy Management System (AEMS) consisting of an airborne digital computer and cockpit displays are presented. The displays provide the pilot with a visual indication of when to manually operate the gear, flaps, and throttles during a delayed flap approach so as to reduce approach time, fuel consumption, and community noise. The AEMS is an independent system that does not interact with other navigation or control systems, and is compatible with manually flown or autopilot coupled approaches. Operational use of the AEMS requires a DME ground station colocated with the flight path reference.

Jackson, D. O.↗

NASA NTRS1982

Solar Heater in a West Virginia College

Solar space-heating and hot water system installed at Alderson-Broaddus College, Philippi, West Virginia, is described in 87-page document. Report contains description of building and its solar-energy system; specifications for solar-energy system, including collectors, coolant, storage tanks, circulation equipment, piping, controls, and insulation; acceptance test data; and discussion of problems with installation, their solution, and recommendations for dealing with excess solar energy.

Source record↗

NASA NTRS2021

Electromagnetic Emission from a Binary Black Hole Merger Remnant in Plasma: Field Alignment and Plasma Temperature

Comparable-mass black-hole mergers generically result in moderate to highly spinning holes, whose spacetime curvature will significantly affect nearby matter in observable ways. We investigate how the moderate spin of a postmerger Kerr black hole immersed in a plasma with initially uniform density and uniform magnetic field affects potentially observable accretion rates and energy fluxes. Varying the initial specific internal energy of the plasma over two decades, we find very little change in steady-state mass accretion rate or Poynting luminosity, except at the lowest internal energies, where fluxes do not exhibit steady-state behavior during the simulation timescale. Fixing the internal energy and varying the initial fixed magnetic-field amplitude and orientation, we find that the steady-state Poynting luminosity depends strongly on the initial field angle with respect to the black hole spin axis, while the matter accretion rate is more stable until the field angle exceeds ∼45°. The protojet formed along the black hole spin axis conforms to a thin, elongated cylinder near the hole, while aligning with the asymptotic magnetic field at large distances.

Bernard J Kelly↗

NASA NTRS1997

A Novel Silicon Micromachined Integrated MCM Thermal Management System

"Micromachining" is a chemical means of etching three-dimensional structures, typically in single- crystalline silicon. These techniques are leading toward what is coming to be referred to as MEMS (Micro Electro Mechanical Systems), where in addition to the ordinary two-dimensional (planar) microelectronics, it is possible to build three-dimensional n-ticromotors, electrically- actuated raicrovalves, hydraulic systems and much more on the same microchip. These techniques become possible because of differential etching rates of various crystallographic planes and materials used for semiconductor n-ticrofabfication. The University of Cincinnati group in collaboration with Karl Baker at NASA Lewis were the first to form micro heat pipes in silicon by the above techniques. Current work now in progress using MEMS technology is now directed towards the development of the next generation in MCM (Multi Chip Module) packaging. Here we propose to develop a complete electronic thermal management system which will allow densifica6on in chip stacking by perhaps two orders of magnitude. Furthermore the proposed technique will allow ordinary conu-nercial integrated chips to be utilized. Basically, the new technique involves etching square holes into a silicon substrate and then inserting and bonding commercially available integrated chips into these holes. For example, over a 100 1/4 in. by 1 /4 in. integrated chips can be placed on a 4 in. by 4 in. silicon substrate to form a Multi-Chip Module (MCM). Placing these MCM's in-line within an integrated rack then allows for three-diniensional stacking. Increased miniaturization of microelectronic circuits will lead to very high local heat fluxes. A high performance thermal management system will be specifically designed to remove the generated energy. More specifically, a compact heat exchanger with milli / microchannels will be developed and tested to remove the heat through the back side of this MCM assembly for moderate and high heat flux applications, respectively. The high heat load application of particular interest in mind is the motor controller developed by Martin Marietta for Nasa to control the thruster's directional actuators on space vechicles. Work is also proposed to develop highly advanced and improved porous wick structures for use in advanced heat loops. The porous wick will be micromachined from silicon using MEMS technology, thus permitting far superior control of pore size and pore distribution (over wicks made from sintered n-ietals), which in turn is expected to led to significantly improved heat loop performance.

Kazmierczak, M. J.↗