Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermal oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A reduced-order modeling of a tubular solar reactor for long duration thermochemical energy storage

The storage of solar energy in a solid form, referred to as a “solar fuel”, can be achieved through a process known as endothermic solar thermochemistry. This process transforms the absorbed solar energy into a stable and retrievable form that can be stored for extended periods of time. This paper presents a low–order heat transfer model of a counter–current tubular falling bed reactor designed to produce thermally reduced magnesium manganese oxide pellets for long duration thermochemical energy storage. The energy required for the endothermic reduction was supplied by concentrated solar energy or renewable electricity via indirect heating of the gas and solid reactants flowing in a ceramic tube. The counter-current gas flow enhances the mixing of the solid particles with the heat recuperation zone, allowing the gas and particles to enter and exit the tubular reactor close to room temperature. Further, the reactor was vertically oriented and was heated circumferentially by an adjustable level heat flux along a finite segment of its length. The temperature distribution of the reactor in response to transient changes along the tube was modeled by considering conduction, convection, and radiation heat transfer. Governing equations for the heat transfer model were solved by discretizing the reactor tube into a finite number of control volumes and using an energy balance for the heat exchange between the reactor wall, gas, and particles within the control volume. The energy absorbed during this endothermic reaction was modeled numerically by fitting the data of the chemical conversion rate with the corresponding temperature of particles in the heating zone. The numerical model has been experimentally validated using a reactor prototype made of a 121.92 cm alumina tube heated by a 7kW electric tube–furnace. The alumina tube receives magnesium manganese oxide pellets of 3.66±0.516 mm in diameter from the top, and a counter–current gas flow from the bottom. The reactor wall temperature was monitored by six thermocouples installed along the reactor tube length. The experimental procedure was numerically simulated, and the temperature variation along the reactor tube was compared with a matrix of experimental runs for a range of particles mass flowrates (0.75–1.25g/s) and corresponding gas flowrates (36–65 SLPM). The reactor system was heated gradually from room temperature to a steady state temperature of 1673K, and then cooled down to room temperature. The heating and cooling processes were simulated, and the numerical and experimental results were compared throughout processes. The numerical model showed similar trends to the experimental results, with an error of 0.69 to 7.9% for the particle inlet and 0.7 to 7.9% for the gas inlet during steady-state operation. The proposed numerical model can be implemented as a simplified physical model to design a feedback control system to regulate reactor temperature.

14 SOLAR ENERGY↗
DOE OSTI2025

Light-Promoted C(sp 3 )–C(sp 3 ) Reductive Elimination from Dialkyl NiII Complexes

Ni-catalyzed cross-coupling is a powerful strategy to forge C(sp 3 )–C(sp 3 ) bonds. Typically, to do so requires overcoming a challenging C–C bond-forming reductive elimination, often enabled by the intermediacy of highly oxidized Ni species or outer-sphere processes. While direct C(sp 3 )–C(sp 3 ) reductive elimination from the Ni II base oxidation state is normally thermally inaccessible, light-activation provides an avenue to affect such transformations. Here, we investigate the mechanism of light-induced C(sp 3 )–C(sp 3 ) bond formation from dialkyl bipyridine Ni II complexes through a variety of organometallic, spectroscopic, and computational studies. Wavelength-dependent quantum yields, ligand electronics–reactivity relationships, excited-state lifetimes, computed barriers, and product distributions from crossover studies support a photolysis/radical rebound mechanism. Furthermore, this reactivity paradigm complements existing strategies in the literature to promote reductive elimination from Ni II , such as the use of destabilizing, sterically hindered ligands and reduction of electron density at Ni through the binding of electron-deficient olefins. Hence, we envision that light-induced reductive elimination may enable the development of challenging C(sp 3 )–C(sp 3 ) couplings.

Alkyls↗
DOE OSTI2024

Transient behavior of oxide fuels with controlled microstructure and Cr2O3 additive

Abstract Microstructure and Cr 2 O 3 doping profoundly impact the thermal-mechanical properties and fracture of oxides fuels. It is a challenge to study the transient behavior of nuclear fuels under loss-of-coolant-event (LOCA). In this study, the crack behavior of UO 2 pellets with controlled grain structure and Cr 2 O 3 doping was tested with rapid power ramping (300−900 °C per min) mimicking a prototypical LOCA heating profile. Dense micron-sized UO 2 pellets display well-maintained integrity without cracking with the ramping up to 1500 °C at a heating rate of 8 °C per second. Fracture occurs in both pure and Cr 2 O 3 -doped dense nano-sized UO 2 pellets. The Cr 2 O 3 doped oxide fuel pellet with a larger grain size (~ 22.2 μm) displays the best performance under LOCA testing due to its highest thermal conductivity under high temperature. FEA calculations suggest a temperature gradient across the fuel pellet during transient testing, resulting in residual stress and cracking, which can be correlated with their thermal-mechanical properties.

Zhao, Dong (ORCID:0000000191377257)↗
DOE OSTI2026

Multi-material direct ink writing and co-sintering of gadolinium oxide – zirconium oxide components

Methods for fabrication of multi-material or functionally graded ceramic composite architectures are of interest for numerous applications. However, conventional co-sintering of multi-material ceramic parts is a challenge because differences in the sintering behavior of the two materials leads to interfacial strain and, ultimately, component failure. Direct ink writing (DIW) is an extrusion-based additive manufacturing process that excels at multi-material printing because multiple extrusion nozzles can be installed on the same gantry system. Furthermore, the use of DIW as a method to fabricate multi-material ceramic green bodies offers an additional variable for controlling and potentially matching sintering kinetics in the slurry formulation used for two dissimilar feedstocks. In the work documented in this manuscript, we explored two strategies to successfully co-sinter multi-material ceramic oxides: slurry optimization to match sintering kinetics and material gradients to step from one material to another. This manuscript also quantifies the allowable mismatch that avoids part cracking in solid solution forming multi-material systems and discusses best strategies to reduce mismatch during co-sintering. Inks composed of gadolinium oxide (Gd 2 O 3 ) and zirconium oxide (ZrO 2 ), a surrogate for uranium oxide (UO 2 ), were thermally matched, which resulted in a sintering mismatch reduction of over 10%. It was found that ~1% mismatch is tolerable during debind cycles and that ~5% mismatch is manageable during sintering cycles after slurry formulations are optimized to match the sintering behavior. Use of continuous gradients is shown to reduce sintering mismatch, although geometric resolution may be lost due to solid solution formation.

Snarr, Patrick L. [Oak Ridge National Laboratory (↗
DOE OSTI2025

Thermal and photoinduced chemistry of the aromatic Criegee intermediate, benzaldehyde oxide: Implications for indoor air quality

Essential oils contain a complex mixture of volatile organic compounds, ranging from terpenes to aromatics. When released into the indoor air environment or into the atmosphere, they may undergo oxidation to generate complex reactive intermediates that affect indoor air quality. Cinnamaldehyde is one such aromatic molecule that is abundant in essential oils. When released into the indoor air environment, it may undergo oxidation to form a carbonyl oxide (Criegee intermediate) with an aromatic substituent: benzaldehyde oxide. In this manuscript, we present a high-level quantum chemical study that shows that, unlike smaller atmospherically relevant Criegee intermediates, benzaldehyde oxide is expected to undergo solar photolysis on timescales that are competitive with its ground state unimolecular and bimolecular chemistry. We show that aromatic substitution leads to a drastic bathochromic shift in the spectroscopically relevant excited states, revealing that photolysis in the indoor or outdoor environment should not be neglected when modeling the climate and air quality implications of Criegee intermediates with extended conjugation. Here, we predict a range of products that may be important for forming lower volatility compounds via tropospherically relevant photochemistry. To motivate future experimental validation of our results, we propose a viable synthetic procedure of the relevant precursor for generating and stabilizing benzaldehyde oxide.

atmospheric photochemistry↗
DOE OSTI2023

Atomic layer deposition of MoO x thin films using Mo( i PrCp) 2 H 2 and O 3

Here, this work studied the growth of molybdenum oxide thin films with thermal atomic layer deposition (ALD) using Mo(iPrCp)2H2 and O3 as precursors. Growth parameters were determined by varying growth temperature and precursor dose times. ALD growth was exhibited in a temperature range of 100–200 °C. The growth per cycle ranged from 1.3 to 1.7 Å/cycle with a standard uniformity parameter of <5%. Attempts to grow films using H2O as an oxygen source showed no significant growth. Film properties were measured using spectroscopic ellipsometry, x-ray reflectivity, x-ray diffraction, x-ray photoelectron spectroscopy, and infrared spectroscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Temperature-Dependent Sheet and Contact Resistivity Measurements on Ag and Ag-Ni Circuit Pastes

The metal circuits and brazes used in electronic, energy conversion, and/or energy storage devices often have difficulty wetting and adhering to ceramic and/or ceramic-passivated metal substrates. Here, a novel Particle Interlayer Directed Wetting and Spreading (PIDWAS) technique is demonstrated that utilizes screen printing, the low wetting angle of silver on nickel, and the high work of adhesion between nickel and various ceramics to produce well-adhered, self-assembled silver patterns on ceramic and/or stainless-steel substrates not normally wet by silver. The resulting Ag-Ni circuits have higher sapphire adhesion strengths (up to 30 MPa on sapphire), higher densities (>97% on sapphire), and similar high-temperature electronic resistivities to those made using commercially-available Heraeus C8710 or DAD-87 silver circuit pastes. Similarly, Ag-Ni brazes between a variety of ceramic and/or stainless-steel substrates have better microstructural stability with rapid thermal cycling, reduction-oxidation cycling, and dual atmosphere isothermal aging than conventional Ag-CuO brazes. In addition, the residual Ni in these Ag-Ni circuits and brazes can be used to chemically getter surface segregated Al, ensuring low contact resistances on a variety of chromia- and/or alumina-passivated stainless steels. Reference: [1] Hu G, Zhou Q, Bhatlawande A, Park J, Termuhlen R, Ma Y, Bieler TR, Yu HC, Qi Y, Hogan T & Nicholas JD. Patterned Nickel Interlayers for Enhanced Silver Wetting, Spreading and Adhesion on Ceramic Substrates. Scripta Materialia, 2021; 196, 113767. 10.1016/j.scriptamat.2021.113767 [2] Park J, Phongpreecha T, Nicholas JD & Qi Y. Enhanced Liquid Metal Wetting on Oxide Surfaces via Patterned Particles. Acta Materialia, 2020; 199, 551-560. 10.1016/j.actamat.2020.08.037

Bhatlawande, Aishwarya↗
DOE OSTI2025

TRISO Particle Isolation and Graphite Removal Using SRNL Vapor Digestion Technology

Tri-structural isotropic fueled reactors are planned to come online in the next decade, but there is not currently a widely agreed upon disposition pathway for this new fuel stream. For long term used nuclear fuel storage, there would be a significant benefit if the waste volume could be reduced or mitigated. Most of the volume from used TRISO fuel contains graphite. SRNL currently has an active patent which describes one pathway to digest the graphite. One benefit in the utilization of this pathway is that multiple cylindrical pieces can be stacked end-to-end in a reaction tube, then nitric acid and water vapor can be flowed through the tube, and the weight change of the individual cores can provide both a reaction profile and overall oxidant use efficiency. The reaction of nitric acid and graphite passes through a series of intermediate products – NO 2 , NO, and N 2 O – from reaction and decomposition to eventually form N2. The data shows that NO2 grows in with increasing temperature between 500-600°C and then decreases by way of either reaction with graphite or decomposition. Nitric oxide, a reaction and thermal decomposition product of NO 2 , exhibits a consistent decline as a function of temperature, which is consistent with the literature. Similarly, the concentrations of N 2 O and N 2 increase as a function of temperature as their reactions with graphite become more favorable.

Advanced Reactors↗
DOE OSTI2021

Produce ZrH Moderator Material

This reports complete Milestone M2.2.3 Produce zirconium hydride moderator material. In this milestone, we report the successful fabrication of FeCrAl alloys cladded zirconium hydride moderator. Different types of crucible designs were presented, including the basic design with bar cladding material, basic design with tube cladding material, and crucible design with position holding function. Mo and FeCrAl were used as the trial cladding materials. The welding techniques and procedures were reported and discussed. Totally three welding techniques were adopted in the development of moderator cladding, and they are electron beam welding (EBW), laser welding (LW), and gas tungsten arc welding (GTAW). After welding, all cladded crucibles were evaluated with two kinds of leak testing, the helium leak test for minor leakage and the bubble test for major leakage. Due to the concern of the poor neutronics performance, Mo was not ideal for future moderator cladding application. Therefore, detailed characterization of the Mo cladded zirconium hydride was not pursued. Instead, the characterization of FeCrAl cladded zirconium hydride was performed. We discussed two material conditions (i.e., as machined and pre-oxidized conditions) prior to the cladding process, evaluated thermal stability of cladded zirconium hydride moderator through directly measuring hydrogen release, and characterized the zirconium hydride following the thermal desorption measurement. The results showed pre-oxidized FeCrAl is capable of efficiently preventing hydrogen release from the moderator assembly.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An Assessment of the Conversion of Biomass and Industrial Waste Products to Activated Carbon

The production of biochar from biomass and industrial wastes provides both environmental and economic sustainability. An effective way to ensure the sustainability of biochar is to produce high value-added activated carbon. The desirable characteristic of activated carbon is its high surface area for efficient adsorption of contaminants. Feedstocks can include a number of locally available materials with little or negative value, such as orchard slash and crop residue. In this context, it is necessary to determine and know the conversion effects of the feedstocks to be used in the production of activated carbon. In the study conducted for this purpose; several samples (piñon wood, pecan wood, hardwood, dried grass, Wyoming coal dust, Illinois coal dust, Missouri coal dust, and tire residue) of biomass and industrial waste products were investigated for their conversion into activated carbon. Small samples (approximately 0.02 g) of the feedstocks were pyrolyzed under inert or mildly oxidizing conditions in a thermal analyzer to determine their mass loss as a function of temperature and atmosphere. Once suitable conditions were established, larger quantities (up to 0.6 g) were pyrolyzed in a tube furnace and harvested for characterization of their surface area and porosity via gas sorption analysis. Among the samples used, piñon wood gave the best results, and pyrolysis temperatures between 600 and 650 °C gave the highest yield. Slow pyrolysis or hydrothermal carbonization have come to the fore as recommended production methods for the conversion of biochar, which can be produced from biomass and industrial wastes, into activated carbon.

09 BIOMASS FUELS↗
DOE OSTI2021

Molecularly tunable heterogeneous catalysts by edge functionalization of graphitic carbons

Disclosed are surface immobilized (electro)catalysts that may be prepared by a condensation reaction that generates an aromatic unit that is robust to acid and base and elevated temperatures. Among their many desirable characteristics, the catalysts are far less prone to the bimolecular deactivation pathways commonly observed for homogeneous catalysts, and may be used in solvents with a range of polarities and dielectric strengths. The catalysts are suitable for a wide array of thermal catalytic reactions (polymerization, oxidation, hydrogenation, cross-coupling etc.) and as anodes and/or cathodes in fuel cells, electrolyzers, and in batteries and supercapacitors.

Surendranath, Yogesh↗
DOE OSTI2022

Temperature-dependent formation of gradient structures with anomalous hardening in an Al–Si alloy

The temperature effect on forming gradient structure in an Al-Si alloy during surface severe deformation is studied in this report. The intermediate temperature (473 K) produces the steepest gradient structure by an anomalous hardening on the top layer compared to lower (300 K) and higher temperature (673 K) counterparts. Our analysis shows profuse aluminum oxide particles in the top layer of the gradient structure under 473 K and thus lead to anomalous hardening by oxide-dispersion strengthening. Here, the counterintuitive enhancement of strengthening at the intermediate temperature is explained by the dynamic interplay between thermal-driven, mechanical-aided oxidation and the wear-induced loss of surface materials as a function of temperature, which yields a critical processing temperature to achieve the steepest gradient structure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-Strength, High-Ductility, High Entropy Alloys with High-Efficiency Native Oxide Solar Absorbers for Concentrating Solar Power Systems

This EPSCoR Project has been investigating the synergy between the excellent high-temperature mechanical behavior of FeMnNiAlCr high entropy alloys (HEA) and the high solar absorptance of their native oxides for high efficiency concentrated solar thermal power (CSP) systems working at >700°C. While HEAs have attracted substantial interest in recent years, most investigations have focused on their applications as structural materials rather than functional materials. This EPSCoR project discovered that FeMnNiAlCr HEAs can potentially be applied synergistically as both a structural and functional material for high-efficiency concentrating solar thermal power (CSP) systems working at >700°C. The HEA itself would be used in high-temperature tubing to carry molten salts or supercritical CO 2 , while its surface oxide would act as a high-efficiency solar thermal absorber. With Fe and Mn being the major components in these HEAs (adding up to ~70 at.% of the alloy), these materials are much more cost-effective than the Ni-based superalloys currently being investigated for high-temperature CSP systems. Through this research, these Fe-Mn based HEAs have demonstrated yield strengths 2-3x greater than that of stainless steel at 700°C and a creep lifetime >800 h at 700ºC under a typical CSP tubing mechanical load of 35 MPa. Their Mn-rich surface oxides maintain a high optical-to-thermal conversion efficiency of ~87% under 1000x solar concentration ratio for 20 simulated day-night thermal cycles between 750ºC and room temperature. In preliminary corrosion studies, these HEAs have sustained immersion in unpurified bromide molten salts for 14 days at 750°C with <2% weight loss, in contrast to 70% weight loss from a 316 stainless steel reference. The simultaneous achievement of promising mechanical, optical, and thermochemical properties in this FeMnNiAlCr system opens the door to new applications of HEAs in solar energy harvesting. Partnerships with Ames Laboratory and Oak Ridge National Laboratory (ORNL) also advanced our understanding of the fundamental structure-property relationships through atomic scale material characterization and first-principles computational modeling. The key research results in this project can potentially be extended to other HEAs and their native oxides. In terms of applications, the proposed FeMnNiAlCr HEA/native oxide system could potentially exceed the mechanical and the optical performance of existing tubing and solar coating materials under EERE’s CSP program at lower cost, which also aligns well with the EPSCoR Science and Technology strategies of New Hampshire in boosting the deployment of renewable energy.

14 SOLAR ENERGY↗
DOE OSTI2021

Structure-activity relationship of Pt catalyst on engineered ceria-alumina support for CO oxidation

In heterogeneous catalysis, the promotion of low temperature activity and enhancement of thermal stability simultaneously especially for precious metal catalysts is always highly demanded but very challenging. In this work, we report a novel Pt catalyst on ceria-alumina (CeO 2 /Al 2 O 3 ) support (Pt/CA-T) engineered by a two-step ceria deposition strategy, exhibiting superior thermal stability and low-temperature carbon monoxide (CO) oxidation activity after activation. Pt single sites anchored to engineered CeO 2 edge sites are much more stable than that to CeO 2 (111) surface, and such stable single sites can be transformed into highly active Pt clusters for efficient low-temperature CO oxidation. Active site identification indicates that the CO oxidation activity of different Pt sites follows such sequence: Pt cluster step sites ≈ Pt cluster terrace sites > Pt cluster corner sites $\gg$ Pt single sites on CeO 2 . The excellent low temperature activity of activated Pt/CA-T catalyst for CO oxidation is associated with its abundant Pt cluster step and terrace sites as well as rich Pt-CeO 2 interfaces, which facilitate the adsorption of active CO species and superior oxygen activation/transfer ability. The present study provides new insights into the structure–activity relationship of Pt-CeO 2 -Al 2 O 3 catalyst, which can also guide the preparation of other highly robust supported catalysts for important industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Highly efficient Pt catalyst on newly designed CeO 2 -ZrO 2 -Al 2 O 3 support for catalytic removal of pollutants from vehicle exhaust

Pt-CeO 2 catalysts have been widely studied for the vehicle emission control. Designing novel CeO 2 based supports with improved physical-chemical properties has become a research hotspot to further promote the catalytic performance and stability of Pt-CeO 2 catalysts. In this work, through utilizing a unique, two-step incipient wetness impregnation (T-IWI) method for ceria-zirconia-alumina (CZA-T) support preparation, a Pt single site catalyst (Pt/CZA-T) with excellent thermal stability was synthesized. Higher oxidation activity and Oxygen storage capacity (OSC) were achieved on activated Pt/CZA-T, comparing to Pt catalysts on regular CeO 2 /Al 2 O 3 (Pt/CA) and one-step prepared CeZrO x /Al 2 O 3 (Pt/CZA). Via the modification of hydrophilic/hydrophobic properties of γ-Al 2 O 3 by this unique T-IWI method, finer Ce 0.9 Zr 0.1 O 2 particles with higher density of surface defects were formed on CZA-T, on which a higher Pt dispersion and stronger Pt-O-Ce interaction were achieved. Upon activation, smaller, well-dispersed Pt clusters on CZA-T were generated. It was concluded that the CO oxidation performance and OSC were highly related to the size of Pt clusters on different supports that we have developed. Finally, more Pt sites located at Pt cluster-CeZrO x interfaces, which were the real active sites, were responsible for the highest OSC function and CO oxidation activity of activated Pt/CZA-T catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗