Search NASA⌕ Search

SEARCH · Search NASA

Results for “threads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Underground storage systems for high-pressure air and gases

This paper is a discussion of the safety and cost of underground high-pressure air and gas storage systems based on recent experience with a high-pressure air system installed at Moffett Field, California. The system described used threaded and coupled oil well casings installed vertically to a depth of 1200 ft. Maximum pressure was 3000 psi and capacity was 500,000 lb of air. A failure mode analysis is presented, and it is shown that underground storage offers advantages in avoiding catastrophic consequences from pressure vessel failure. Certain problems such as corrosion, fatigue, and electrolysis are discussed in terms of the economic life of such vessels. A cost analysis shows that where favorable drilling conditions exist, the cost of underground high-pressure storage is approximately one-quarter that of equivalent aboveground storage.

Beam, B. H.↗
NASA NTRS1975

Measurements of the performance of an electrohydrodynamic heat pipe

The performance of an electrohydrodynamic heat pipe formed by enclosing three straight axial electrodes with a 1.27 cm O.D. internally threaded stainless steel tube was measured with Freon-11 as working fluid. The condenser and evaporator conductances at low power were comparable to those measured in a conventional capillary driven heat pipe using similar working fluids. The evaporator conductance improved at high power probably due to the onset of nucleate boiling. The maximum heat throughput for this pipe was substantially higher than that of a conventional pipe.

Loehrke, R. I.↗
NASA NTRS1975

Propulsion technology needs for advanced space transportation systems

Plans have been formulated for chemical propulsion technology programs to meet the needs of advanced space transportation systems during the two decades from 1980 to the year 2000. The many possible vehicle applications have been reviewed and cataloged to isolate the common threads of primary propulsion technology that will satisfy near term requirements in the first decade and at the same time establish the technology groundwork for various potential far term applications in the second decade. Two thrust classes of primary propulsion engines are apparent: (1) 5,000 to 30,000 pounds thrust for upper stages and space maneuvering; (2) large booster engines of over 250,000 pounds thrust. Six major classes of propulsion systems and the important subdivisions of each class have been identified. The relative importance of each class is discussed in terms of the number of potential applications, the likelihood of that application materializing, and the criticality of the technology needed. Specific technology programs are described and scheduled to fulfill the anticipated primary propulsion technology requirements of the period.

Gregory, J. W.↗
NASA NTRS1975

Implications of Pioneer-2 magnetic field models for Jupiter's decametric radio mission

The geometry and electron gyrofrequency were calculated for both the North and South feet of the Io-threaded flux tube at several altitudes as a function of sub-Io longitude for various multipole field models. The models predict a maximum surface gyrofrequency equal to the observed high frequency limit of the decameter-wave radio emission (DAM) and tend to favor a mechanism involving transverse propagation from a source in the Northern hemisphere. Calculations indicate that the beaming pattern of the emission may be determined by reflection from the ionosphere rather than by inherent beaming from the source region.

Alexander, J. K.↗
NASA NTRS1976

Design evolution of a low shock release nut

Design improvements and detailed functional analyses are reviewed to trace the development of a pyroactuated release device with segmented thread design from its intermediate design into one that reduces the levels of shock spectra generated during its operation by 50%. Comparisons of shock output and internal load distribution are presented, along with descriptions of mechanical operation for both designs. Results also show the potential areas where design development activity can gain further progress in lowering actuation shock levels.

Otth, D. H.↗
NASA NTRS1976

Transverse tensile and stress rupture properties of gamma/gamma prime-delta directionally solidified eutectic

Tensile and stress rupture properties were determined primarily at 760 C for specimens oriented at various angles (0 deg, 10 deg, 45 deg, and 90 deg) from the solidification direction of bars and/or slabs of the Ni-20Cb-6Cr-2.5A (gamma/gamma prime-delta) eutectic. Threaded-head specimens yielded longer rupture lives with significantly less scatter than did tapered-head specimens. Miniature specimens are suitable for determining traverse tensile and rupture properties of 1.2 centimeter diameter bar stock. The 300 hour rupture stress at 760 C for specimens oriented at 10 deg from the solidification direction was reduced from 740 to 460 MPa, and to 230 MPa for material oriented at either 45 deg or 90 deg.

Gray, H. H.↗
NASA NTRS1976

A local diffusion process associated with the sweeping of energetic particles by Io

A local, turbulent diffusion process which may rapidly refill the partial cavity of energetic particles created by Io's passage through a flux tube is discussed. A model is developed of Io's sweeping action on energetic particles in which a wake is formed behind the flux tube threading Io. It is shown to be possible that this wake contains an excess of positive charge, thereby creating an electric field. The particle drift produced by this field, coupled with the density gradient of energetic protons, can generate an instability. It is this instability that is responsible for the turbulent diffusion process. The sweeping of energetic particles is also discussed in relation to particle energy and pitch angle distribution.

Huba, J. D.↗
NASA NTRS1976

Plasma injection at synchronous orbit and spatial and temporal auroral morphology

Analysis of ATS 5 particle spectrograms and simultaneous meridian-scanning photometer data obtained at the base of the ATS field line has revealed systematic relationships between temporal and spatial auroral morphology and particle-injection events. The details of these relationships depend on previous injection events, the local time of the observatory with respect to current-injection events, and the extent and magnitude of current injections. A persistent zone of weak aurora is related to steady plasma-sheet drizzle, and the equatorward edge of this aurora delineates field lines threading the inner edge of the plasma sheet. Auroras associated with injection events superimpose on this preexisting pattern, with the lowest latitude of new precipitation depending on local time. In general, plasma energization is not required between the equatorial plane and the ionosphere to account for observed auroral intensities. The data indicate occasional occurrence of enhanced loss-cone fluxes, suggesting low-altitude field-aligned acceleration. A summary figure shows how various characteristic auroral-precipitation regions are related to the shape, extent, and orientation of the substorm injection boundary and to the subsequent drift paths of injected plasma.

Eather, R. H.↗
NASA NTRS1978

No-spill touchup paint container

Container has two-piece threaded device that is installed in hole in standard metal lid. In addition to preventing spillage, device provides better brush support and wiper edge.

Peters, R. L.↗
NASA NTRS1976

Impact tensile testing of wires

The test consists of fixing one end of a wire specimen and allowing a threaded falling weight to strike the other. Assuming the dynamic stress in the wire to be a function only of its strain, energy considerations show for negligible wire inertia effects that the governing dynamic stress-strain law can be determined directly from impact energy vs. wire elongation data. Theoretical calculations are presented which show negligible wire inertia effects for ratios of wire mass to striking mass of the order of .01 or less. The test method is applied to soft copper wires and the dynamic stress-strain curve so determined is found to be about 30 percent higher than the corresponding static curve.

Dawson, T. H.↗
NASA NTRS1977

The effect of configuration on strength, durability, and handle of Kevlar fabric-based materials

Five Kevlar based laminates and three Kevlar based coated materials were designed, hand made, and tested against comparative conventional Dacron based materials for strength, peel, tear, puncture, creases, and handle. Emphasis was placed on evaluating geometric orientation of constituents, use of elastomeric film in place of high modulus films, and the use of flying thread loom bias reinforcement of Kevlar yarns. Whereas, the performance of the Kevlar laminates was severely degraded by crease effects, significant gains in overall performance factors were shown for the coated Kevlar materials.

Reuter, L. L.↗
NASA NTRS1976

On tenuous plasmas, fireballs, and boundary layers in the earth's magnetotail

The plasma instrumentation (the Lepedea) and the magnetometer aboard IMP 8 performed correlative measurements of magnetic fields and plasmas within the geomagnetic tail at geocentric radial distances of about 23-46 R-E during March-October 1974. The hot tenuous plasmas within the plasma sheet were found to be in a state of almost continuous flow and were threaded with northward, or closed geomagnetic lines. The satellite encountered a region of acceleration in the magnetotail, the 'fireball' which exhibits strong jetting of plasmas in excess of 1000 km/s, proton temperatures of about 10 to the 7th K, disordered magnetic fields, southward magnetic fields during tailward jetting of plasmas, and northward magnetic fields for fast plasma flows toward earth. In addition, the magnetosheath plasmas within the boundary layers which are contiguous to the plasma sheet display evidence of plasma heating, great changes in bulk flow velocities, and acceleration of energetic electrons with an energy of greater than 45 keV.

Frank, L. A.↗
NASA NTRS1977

A CW ultrasonic bolt-strain monitor

There exists a need for a relatively inexpensive system for measuring strain in bolts. The torque wrench is one technique for straining bolts which has been widely applied. Unfortunately, friction in the bolt threads and between the nut and the work tend to make such a simple system inaccurate. In practice, a torque wrench is unacceptable for many situations where strain is critical. In this article, an ultrasonic technique is described which can indicate changes in bolt strain to better than one part in 10,000. The technique is based on the one-dimensional propagating-ultrasonic-wave model and uses a new ultrasonic instrument called a Reflection Oscillator Ultrasonic Spectrometer which is a closed-loop feedback marginal-oscillator system that frequency locks the device to the peak of a mechanical resonance in the bolt. The instrument indicates a shift in the bolt resonance frequency due to elongation and changes in velocity of sound due to strain. Data are presented comparing a standard torque wrench to the ultrasonic monitor for different measured stresses on the bolt as well as for different bolt conditions. The strain instrument can be used to monitor changing stresses, to measure material properties and may be applied as a strain gage or load cell.

Heyman, J. S.↗
NASA NTRS1977

Physics of an active region loop system

The structure of the active region loops is investigated by the study of a loop complex which undergoes a dramatic evacuation of most of the mass it contains. The need for continual energy deposition in loops is emphasized by the apparent cessation of energy input to the loops studied and their subsequent behavior. Estimates are made of the energy necessary to form and to maintain the loops, and of the relative importance of radiation and thermal conduction as energy loss mechanisms. Models based on the observed EUV emission are used to place limits on the size of loops seen in various lines and on the density and temperature structure. It is found that the cool cores of active region loops are likely to be no more than a few hundred kilometers in radius and that several such cool threads may be imbedded in a common hot outer sheath. The primary energy loss on a large scale is radiation with thermal conduction contributing to local disturbances. There is a tendency for the development of apparently unstable condensations or knots along the length of a loop.

Levine, R. H.↗
NASA NTRS1977

A structured surface for high performance evaporative heat transfer

An evaporative surface is described for heat pipes and other two-phase heat transfer applications that consists of a hybrid composition of V-grooves and capillary wicking. Characteristics of the surface include both a high heat transfer coefficient and high heat flux capability relative to conventional open faced screw thread surfaces. With a groove density of 12.6/cm and ammonia working fluid, heat transfer coefficients in the range of 1 to 2 W/sq cm K have been measured, along with maximum heat flux densities in excess of 20 W/sq cm. A peak heat transfer coefficient in excess of 2.3 W/sq cm K at 20 W/sq cm was measured with a 37.8/cm hybrid surface.

Saaski, E. W.↗
NASA NTRS1978

Nylon screws make inexpensive coil forms

Standard nylon screws act as coil form copper wire laid down in spiral thread. Completed coil may be bonded to printed-circuit board. However, it is impossible to tune coil by adjusting spacing between windings, technique sometimes used with air-core coils.

Aucoin, G.↗
NASA NTRS1978

Flicking-wire drag tensioner

Wire-drag system improves wire profile and applies consistent drag to wire. Wire drag is continuously adjustable from zero drag to tensile strength of wire. No-sag wire drag is easier to thread than former system and requires minimal downtime for cleaning and maintenance.

Dassele, M. A.↗
NASA NTRS1978

Ultrasonic extensometer measures bolt preload

Extensometer using ultrasonic pulse reflections to measure elongations in tightened belts and studs is much more accurate than conventional torque wrenches in application of specified preload to bolts and other threaded fasteners.

Daniels, C. M., Jr.↗