Search NASA⌕ Search

SEARCH · Search NASA

Results for “transferability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Conjugate Heat Transfer Analysis of the Supercritical CO2 Based Counter Flow Compact 3D Heat Exchangers

Compact heat exchangers using supercritical fluids such as CO2 are preferred due to their high heat transfer capacity and smaller footprint. Three-dimensional conjugate forced convection heat transfer analysis was performed on several shell-and-tube counter-flow microchannel heat exchangers. Numerical simulations were conducted to test effect of change in mass flow rate, hydraulic diameter and various cross sections on the heat transfer. Increasing mass flow rate improved heat transfer up to a maximum value and then decreased downstream with increasing turbulence. Maximum heat transfer was obtained for the micro channel with the smallest hydraulic diameter. Amongst the cross sections analyzed (circular, square, circular with radial ribs, and square with radial ribs), the most uniform distribution of temperature and maximum heat transfer were obtained for circular cross section with radial ribs. An optimally efficient operation of such a heat exchanger can be attained by considering these factors during multi-objective constrained optimization of geometric parameters and requirements for additive manufacturing of such compact heat exchangers.

Chitale, Janhavi↗
DOE OSTI2022

Experimental Study of Eutectic Molten Salts NaCl/KCl/ZnCl2 Heat Transfer Inside a Smooth Tube for High-Temperature Application

Abstract Eutectic salts NaCl-KCl-ZnCl2 and NaCl-KCl-MgCl2 are two of the chloride salt systems that are promising for being used as high-temperature heat transfer fluid (HTF) and thermal energy storage (TES) materials in a wide range of temperatures from 230 °C to 750 °C in concentrated solar thermal power systems. To conduct measurement of the heat transfer coefficient of the molten salt at high temperatures, a circulation system and instrumentation of flow and heat transfer was constructed. Experimental measurement of the convective heat transfer coefficients of NaCl-KCl-ZnCl2 (molar fraction: 13.8–41.9–44.3%) inside tubes has been accomplished to find the most suitable heat transfer correlations. Experience of salt processing and operation of the high-temperature heat transfer test system was obtained. Two correlations, Dittus-Boelter equation and Gnielinski’s correlation for Nusselt number against Reynolds number and Prandtl number, are evaluated using the test results, and the latter correlation is recommended due to its better agreement of prediction against tested data.

Energy & Fuels↗
DOE OSTI2020

Photoinduced electron transfer from zinc meso -tetraphenylporphyrin to a one-dimensional perylenediimide aggregate: Probing anion delocalization effects

Organic photovoltaics incorporating non-fullerene acceptors based on perylenediimide (PDI) now rival fullerene acceptor-based devices in performance, although the mechanisms of charge generation in PDI-based devices are not yet fully understood. Fullerene-based systems are proposed to undergo electron transfer directly from the photoexcited donor into a band of delocalized acceptor states, thus increasing charge generation efficiency. Similarly, anion delocalization has been shown to enhance the rate of electron transfer from a photoexcited donor to two electronically coupled PDI acceptors. Here we investigate how additional electron acceptors may further increase the rate of electron transfer from the donor zinc meso-tetraphenylporphyrin (ZnTPP) to an aggregate of PDI acceptors (PDI[Formula: see text]. Femtosecond transient visible and mid-infrared absorption spectroscopies show that the rate of electron transfer from 1 *ZnTPP to the PDI assembly ZnTPP 2 -PDI 3 is statistically identical to that of the previously examined ZnTPP-PDI 2 . A Marcus theory analysis indicates that the parameters governing electron transfer are nearly identical for the two molecules, suggesting that the maximum electron transfer rate enhancement has been achieved in a cofacial PDI dimer because the ZnTPP directly couples to the first two PDI acceptors whereas the coupling to the third PDI is too weak.

bio-inspired↗
DOE OSTI2021

Enhancing Steam-Side Heat Transfer via Microdroplet Ejection using Inorganic Coatings

During condensation of water on a superhydrophobic nanostructured surfaces, droplets coalesce and jump (droplet ejection) due to the release of excess surface energy. Meticulously designed nanostructured surfaces or coatings capable of droplet ejection can enhance heat transfer performance by easy removal of droplets during condensation. In the present work, the capabilities of the Nelumbo droplet ejection coatings technology currently used in commercial heat exchangers are explored and optimized for materials and conditions relevant to steam condensers. Specifically, this includes (1) adapting and optimizing the procedures and chemistries to deposit droplet ejecting coatings on materials used in the steam condenser, (2) testing of the heat transfer, durability, and fouling of the fabricated coatings under a variety of steam condenser relevant conditions, and (3) modeling of the impact of droplet dynamics and interfacial properties on heat transfer in steam condensers. We experimentally demonstrated that at low supersaturation conditions (S~1.02), developed superhydrophobic nanostructured surface gives a 40% higher peak heat transfer flux and a 17% higher peak overall heat transfer coefficient (U) with droplet ejection mechanism compared to the dropwise condensation mechanism on the same nanostructured surface. Though the experimentally observed droplet ejection mechanism was short-lived (~3 min) due to the limitation of the chiller to maintain a constant supersaturation condition in fabricated steam condenser. And large variations in water inlet temperature (+ to - 2 degrees C) caused flooding of nanostructure (Wenzel state) at higher supersaturation (S > or = 1.12). This is an important finding because typical supersaturation levels in field operation are over 1.8 and as such, either the flooding potential for these materials should be improved or operation at lower supersaturation may be required to maximize heat transfer efficiency. If supersaturation conditions can be maintained reliably in the steam condenser in addition to droplet ejection mechanism during condensation, this could provide a potential 2% reduction in water flow rate which equates to a savings of over 3900 gallons of water per minute for a 500 MW steam turbine and over $0.3MM savings annually given a 0.02 cent marginal water withdrawal cost. It is also worth noting that these savings are based on improvement of droplet ejection coatings over coatings capable of performing consistent dropwise mechanism in in-field surface condensers. Savings due to the droplet ejections coatings when compared to bare substrates could be much higher. Additionally, the present work provides the importance of steam condenser operating conditions and insights into the challenges in modeling the condensing droplet dynamics on surfaces.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Mechanisms Underlying Plastocyanin-Cytochrome f Electron Transfer Investigated via Site-Specific Linear and Two-dimensional Infrared Spectroscopy

The goal of this research is to further our understanding of biological electron transfer in photosynthesis through the development and application of new methods for studying proteins with high spatial and temporal detail. Biological electron transfer occurs between metal sites imbedded in proteins where the environment and its motions can be very different from those of normal bulk liquids. Moreover, electron transfer between two proteins typically involves short-lived binding interactions within a highly mobile complex. We have directed our studies at photosynthetic electron transfer proteins plastocyanin and cytochrome f. We have labeled two key ligands to the copper ion of plastocyanin with carbon deuterium probe vibrations that enable their selective analysis by infrared spectroscopy. This analysis has shown that association of plastocyanin with cytochrome f leads to large changes in the bonding between the copper ion and ligands. In addition, the probes have been used to assess the contribution of the protein scaffold of plastocyanin in dictating the copper coordination geometry. We also have made progress to extend our experiments from equilibrium to non-equilibrium studies. The studies help to illuminate how proteins are tuned to control biological electron transfer. A better understanding of electron transfer reactions in natural photosynthesis will bolster efforts to develop artificial systems for energy production.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Determination of Vibrational Motions Driving Photoinduced Electron Transfer Reactions in Molecular Crystals and Organic Thin Films

The objective of this research is to develop an understanding of how nuclear motions can be used to drive and control photo-induced charge transfer and singlet fission reactions in molecular crystals and thin films. By following the structural evolution of reacting molecules and nanostructures on the timescale of their nuclear motion, we will determine what interplay of nuclear coordinates is most efficient in driving electron transfers, a necessary first step in most photovoltaic and photocatalytic processes. We will identify which nuclear coordinates effectively promote desirable electron transfer processes, or ineffectively dissipate photon energy into unwanted thermal energy, thus guiding the design and implementation of molecular systems tailored for high efficiency processes. Specifically, we aim to identify which nuclear coordinates are responsible for driving electron transfer and singlet fission reactions at different points along the reaction coordinate, particularly in regimes which deviate from Marcus theory predictions. We will do so by investigating systems with electron transfer and singlet fission occurring from non-thermalized states due to strong donor-acceptor electronic coupling. First, we will prove that specific vibrational modes are responsible for charge transfer processes in molecular crystals. Secondly, we will investigate how vibrational coherences and specific nuclear motions can be used to drive high yield singlet fission processes. Finally, we will determine how complex film morphology affects long-range charge transport, a key limiting factor in our ability to make gains in efficiency.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Mass transfer coefficients, kL, and air-CO2 ingassing rates in 3.4 m2 and 1-acre raceway ponds.

The US DOE 2016 Billion Ton Update (Langholtz 2016) projected that CO2 in flue-gas from power plants or similar sources would limit U.S. algal biofuel potential to under 5 billion gallons gasoline equivalent (gge) per year, due to lack of sufficient land, water and other requirements near such flue gas sources. 2nd generation carbon capture technologies are proposed to overcome this constraint (Davis 2017), and could expand this resource potential nearly 10-fold, assuming CO2 costs near the future, 2025 DOE NETL, goal of $40/metric ton CO2. An alternative pathway is the direct uptake of air CO2 into the algal ponds through an increase in the air-CO2 transfer rate resulting from the reaction of CO2 with hydroxide ions. However, such a ‘chemical enhancement’ in mass transfer depends on a high pH in the culture, and, by extension, the ability of microalgae to maintain high rates of carbon assimilation under such conditions. Abiotic experiments characterized the air-CO2 mass-transfer rate in 1-acre and 3.4 m2 raceway ponds as a function of pH, with rates approaching 10 g C/m2-day at pH 12 in the brackish water tested, equivalent to a biomass productivity potential of near 20 g AFDW/m2-day (@ 0.47 g C/g AFDW). The mass transfer rate was found to be nearly independent of the mass-transfer coefficient, indicating that at turbulence levels achievable in typical raceway ponds, the system is reaction rate, rather than diffusion limited. In biotic trials with an unknown green microalga, biomass productivity in ponds receiving CO2 from only direct surface air-CO2 exchange averaged 5 +/- 0.5 g AFDW/m2-day in August - September central California conditions, about half-that of experimental controls fertilized with supplemental CO2. pH in the air-only treatment reached a maximum of 10.5, supporting a model predicted air-CO2 ingassing rate between 2-3 g C/m2-day, consistent with the observed biomass carbon assimilation rate. Results suggest that unique alkaliphilic strains are required if reliant on direct in-pond air-CO2 transfer for algal inorganic carbon supply, and that reaching an economically viable biomass productivity will require strains that thrive at pH 11 and above.

09 BIOMASS FUELS↗
DOE OSTI2025

Polymer-assisted transfer of MBE-grown van der Waals materials

Molecular beam epitaxy (MBE) has been used to create high-quality, large-scale two-dimensional van der Waals (2D vdW) materials. However, due to the strong adhesion between the substrate and deposited materials, the peel-off and dry transfer of MBE-grown vdW films onto other substrates has been challenging. This limits the study and use of MBE films for heterogeneous integration including stacked and twisted heterostructures. In this work, we develop a polymer-assisted dry transfer method and successfully perform full-film transfer of various MBE-grown 2D vdW materials including transition metal dichalcogenides (TMD), topological insulators (TI) and 2D magnets. In particular, we transfer air-sensitive 2D magnets, characterize their magnetic properties, and compare them with as-grown materials. The results show that the transfer technique does not degrade the magnetic properties, with the Curie temperature and hysteresis loops exhibiting similar behaviors after the transfer. Our results enable further development of heterogeneous integration of 2D vdW materials based on MBE growth.

Li, Ziling [The Ohio State University]↗
NASA NTRS1963

Radiant Heat Transfer to Absorbing Gases Enclosed Between Parallel Flat Plates with Flow and Conduction

An analysis is presented for obtaining two-dimensional temperature profiles and heat transfer in a radiation-absorbing gray gas of uniform absorptivity under the combined influence of thermal radiation, conduction, and gas flow. The gas is enclosed in a channel of infinite width and finite length formed by two semi-infinite parallel flat plates. These plates are black emitting surfaces, and the ends of the channel are formed by porous black surfaces through which the gas can flow into or out of the channel. These porous black end surfaces are used to simulate the radiation environment external to the channel. First, results are obtained for heat transfer between the plates in the absence of both conduction and flow. These results are found to be in good agreement with those obtained for the same conditions by previous workers. Results are then presented for heat transfer between the plates for the case of a radiating and conducting, but stagnant, gas separating the plates. The effects of the interactions between radiation and conduction are discussed. It was found that the heat transfer for combined radiation and conduction in an absorbing gas is slightly greater than the sum for each process taken separately. Finally, results are given for heat transfer from the plates to a flowing, radiating gas in the absence of conduction. The two plates are at the same temperature, and the gas enters the channel with uniform velocity and temperature. The results obtained for this case indicate that the heat transferred to the flowing gas from the constant temperature surfaces goes through a maximum as the absorptivity of the gas increases. This is in qualitative agreement with earlier results obtained by other investigators. All the results are presented in terms of dimensionless parameters, for the sake of generality, and the derivation of the dimensionless parameters, which are indicative of the effects of conduction and flow is presented.

Gray Gas↗
NASA NTRS1971

Optimum transfer between hyperbolic asymptotes with turn angle less than the maximum natural turn angle.

The impulsive transfer of minimum characteristic velocity between two given hyperbolic asymptotes associated with a real planet is considered. The constraint of remaining above the surface of the planet introduces a maximum natural turn angle. This divides the problem naively into two categories. The first is the case when the turn angle required by the given asymptotes is less than or equal to the maximum natural turn angle. This is the more reasonable situation for a swingby maneuver, and is the case considered in this paper. The resulting optimal transfers are of five basic types. In boundary conditions space, by far the largest area of transfers are either single impulse transfers or transfers through the parabolic level requiring two finite impulses. In no case has an optimal transfer been found which uses more than two finite impulses and three infinitesimal impulses. Complete results are presented for the case in which the given turn angle is less than or equal to the maximum natural turn angle.

Walton, J. M.↗
NASA NTRS1975

Pressure gradient effects on heat transfer to reusable surface insulation tile-array gaps

An experimental investigation was performed to determine the effect of pressure gradient on the heat transfer within space shuttle reusable surface insulation (RSI) tile-array gaps under thick, turbulent boundary-layer conditions. Heat-transfer and pressure measurements were obtained on a curved array of full-scale simulated RSI tiles in a tunnel-wall boundary layer at a nominal free-stream Mach number and free-stream Reynolds numbers. Transverse pressure gradients of varying degree were induced over the model surface by rotating the curved array with respect to the flow. Definition of the tunnel-wall boundary-layer flow was obtained by measurement of boundary-layer pitot pressure profiles, wall pressure, and heat transfer. Flat-plate heat-transfer data were correlated and a method was derived for prediction of heat transfer to a smooth curved surface in the highly three-dimensional tunnel-wall boundary-layer flow. Pressure on the floor of the RSI tile-array gap followed the trends of the external surface pressure. Heat transfer to the surface immediately downstream of a transverse gap is higher than that for a smooth surface at the same location. Heating to the wall of a transverse gap, and immediately downstream of it, at its intersection with a longitudinal gap is significantly greater than that for the simple transverse gap.

Throckmorton, D. A.↗
NASA NTRS1976

Vibration-translation energy transfer in vibrationally excited diatomic molecules

A semiclassical collision model is applied to the study of energy transfer rates between a vibrationally excited diatomic molecule and a structureless atom. The molecule is modeled as an anharmonic oscillator with a multitude of dynamically coupled vibrational states. Three main aspects in the prediction of vibrational energy transfer rates are considered. The applicability of the semiclassical model to an anharmonic oscillator is first evaluated for collinear encounters. Second, the collinear semiclassical model is applied to obtain numerical predictions of the vibrational energy transfer rate dependence on the initial vibrational state quantum number. Thermally averaged vibration-translation rate coefficients are predicted and compared with CO-He experimental values for both ground and excited initial states. The numerical model is also used as a basis for evaluating several less complete but analytic models. Third, the role of rational motion in the dynamics of vibrational energy transfer is examined. A three-dimensional semiclassical collision model is constructed with coupled rotational motion included. Energy transfer within the molecule is shown to be dominated by vibration-rotation transitions with small changes in angular momentum. The rates of vibrational energy transfer in molecules with rational frequencies that are very small in comparison to their vibrational frequency are shown to be adequately treated by the preceding collinear models.

Mckenzie, R. L.↗
NASA NTRS1977

The Riccati transfer matrix method

The Riccati transfer matrix method is a new technique for analyzing structural members. This new technique makes use of an existing large catalog of transfer matrices for various structural members such as rotating shafts. The numerical instability encountered when calculating high resonant frequencies, static response of a flexible member on a stiff foundation, or the response of a long member by the transfer matrix method is eliminated by the Riccati transfer matrix method. The computational time and storage requirements of the Riccati transfer matrix method are about half the values for the transfer matrix method. A rotating shaft analysis demonstrates the numerical accuracy of the method.

Horner, G. C.↗
NASA NTRS1981

Heat transfer coefficients for staggered arrays of short pin fins

Short pin fins are often used to increase that heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).

Vanfossen, G. J.↗
NASA NTRS1981

Heat transfer coefficients for staggered arrays of short pin fins

Short pin fins are often used to increase the heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).

Vanfossen, G. J.↗
NASA NTRS1982

Heat transfer from combustion gases to a single row of closely spaced tubes in a swirl crossflow Stirling engine heater

This paper describes an experimental program to determine the heat-transfer characteristics of a combustor and heat-exchanger system in a hybrid solar receiver which utilizes a Stirling engine. The system consists of a swirl combustor with a crossflow heat exchanger composed of a single row of 48 closely spaced curved tubes. In the present study, heat-transfer characteristics of the combustor/heat-exchanger system without a Stirling engine have been studied over a range of operating conditions and output levels using water as the working fluid. Nondimensional heat-transfer coefficients based on total heat transfer have been obtained and are compared with available literature data. The results show significantly enhanced heat transfer for the present geometry and test conditions. Also, heat transfer along the length of the tubes is found to vary, the effect depending upon test condition.

Bankston, C. P.↗
NASA NTRS1985

Optimal aeroassisted transfer between coplanar elliptical orbits

An attempt is made to solve the problem of orbital transfer between coplanar elliptical orbits. Pure propulsive transfer is analyzed with the restriction of two impulses for the transfer. The optimal switching conditions are reviewed, and it is shown that the solution is obtained by solving a set of three nonlinear equations for three unknowns. A semianalytical solution is obtained to the problem of planar rotation of an orbit for the pure propulsive maneuver, and it is shown that, for high eccentricity and rotation angle, aeroassisted transfer is a fuel-saving maneuver. It is demonstrated that complete circularization of the intermediate orbit is not necessary in the optimal aeroassisted transfer. An analytical proof is presented, giving an explicit condition for noncircularization. A complete numerical solution is presented for a case of optimal aeroassisted transfer from a low-energy orbit to a high-energy orbit.

Vinh, N. X.↗
NASA NTRS1986

Measurement of heat transfer and pressure drop in rectangular channels with turbulence promoters

Periodic rib turbulators were used in advanced turbine cooling designs to enhance the internal heat transfer. The objective of the present project was to investigate the combined effects of the rib angle of attack and the channel aspect ratio on the local heat transfer and pressure drop in rectangular channels with two opposite ribbed walls for Reynolds number varied from 10,000 to 60,000. The channel aspect ratio (W/H) was varied from 1 to 2 to 4. The rib angle of attack (alpha) was varied from 90 to 60 to 45 to 30 degree. The highly detailed heat transfer coefficient distribution on both the smooth side and the ribbed side walls from the channel sharp entrance to the downstream region were measured. The results showed that, in the square channel, the heat transfer for the slant ribs (alpha = 30 -45 deg) was about 30% higher that of the transverse ribs (alpha = 90 deg) for a constant pumping power. However, in the rectangular channels (W/H = 2 and 4, ribs on W side), the heat transfer at alpha = 30 -45 deg was only about 5% higher than 90 deg. The average heat transfer and friction correlations were developed to account for rib spacing, rib angle, and channel aspect ratio over the range of roughness Reynolds number.

Han, J. C.↗