Search NASA⌕ Search

SEARCH · Search NASA

Results for “transient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Computational aspects of sensitivity calculations in transient structural analysis

A key step in the application of formal automated design techniques to structures under transient loading is the calculation of sensitivities of response quantities to the design parameters. This paper considers response quantities to the design parameters. This paper considers structures with general forms of damping acted on by general transient loading and addresses issues of computational errors and computational efficiency. The equations of motion are reduced using the traditional basis of vibration modes and then integrated using a highly accurate, explicit integration technique. A critical point constraint formulation is used to place constraints on the magnitude of each response quantity as a function of time. Three different techniques for calculating sensitivities of the critical point constraints are presented. The first two are based on the straightforward application of the forward and central difference operators, respectively. The third is based on explicit differentiation of the equations of motion. Condition errors, finite difference truncation errors, and modal convergence errors for the three techniques are compared by applying them to a simple five-span-beam problem. Sensitivity results are presented for two different transient loading conditions and for both damped and undamped cases.

Greene, William H.↗
NASA NTRS1989

Transient coronal extreme ultraviolet emission before and during the impulsive phase of a solar flare

Transient coronal EUV emission, recorded in an emission line of Fe XI at 180.4 A, has been observed prior to and during the initial stages of a solar flare. This emission provides direct evidence of the interactions between the lower corona and the chromosphere during flare initiation. The first EUV enhancement was correlated with activation and eruption of a filament, extended over a distance of about 120,000 km, and had an emission maximum at the site of filament disruption. A moving source of EUV emission also appeared along the trajectory of the erupting filament as it accelerated through the low corona. The mass of this source is estimated to be greater than that of the initial filament or surrounding corona, implying an additional mass ejection from the chromosphere. EUV emission during the impulsive phase of the flare consisted of transient sources along the photospheric magnetic neutral line, with intervening regions of lesser intensity that are interpreted as transient coronal loops below the erupting filament.

Neupert, Werner M.↗
NASA NTRS1989

Active Control of the Forced and Transient Response of a Finite Beam

When studying structural vibrations resulting from a concentrated source, many structures may be modelled as a finite beam excited by a point source. The theoretical limit on cancelling the resulting beam vibrations by utilizing another point source as an active controller is explored. Three different types of excitation are considered, harmonic, random, and transient. In each case, a cost function is defined and minimized for numerous parameter variations. For the case of harmonic excitation, the cost function is obtained by integrating the mean squared displacement over a region of the beam in which control is desired. A controller is then found to minimize this cost function in the control interval. The control interval and controller location are continuously varied for several frequencies of excitation. The results show that control over the entire beam length is possible only when the excitation frequency is near a resonant frequency of the beam, but control over a subregion may be obtained even between resonant frequencies at the cost of increasing the vibration outside of the control region. For random excitation, the cost function is realized by integrating the expected value of the displacement squared over the interval of the beam in which control is desired. This is shown to yield the identical cost function as obtained by integrating the cost function for harmonic excitation over all excitation frequencies. As a result, it is always possible to reduce the cost function for random excitation whether controlling the entire beam or just a subregion, without ever increasing the vibration outside the region in which control is desired. The last type of excitation considered is a single, transient pulse. A cost function representative of the beam vibration is obtained by integrating the transient displacement squared over a region of the beam and over all time. The form of the controller is chosen a priori as either one or two delayed pulses. Delays constrain the controller to be causal. The best possible control is then examined while varying the region of control and the controller location. It is found that control is always possible using either one or two control pulses. The two pulse controller gives better performance than a single pulse controller, but finding the optimal delay time for the additional controllers increases as the square of the number of control pulses.

Post, John Theodore↗
NASA NTRS1989

Transient Pressure Test Article Test Program

The Transient Pressure Test Article (TPTA) test program is being conducted at a new test facility located in the East Test Area at the National Aeronautics and Space Administration's (NASA's) Marshall Space Flight Center (MSFC) in Huntsville, Alabama. This facility, along with the special test equipment (STE) required for facility support, was constructed specifically to test and verify the sealing capability of the Redesigned Solid Rocket Motor (RSRM) field, igniter, and nozzle joints. The test article consists of full scale RSRM hardware loaded with inert propellant and assembled in a short stack configuration. The TPTA is pressurized by igniting a propellant cartridge capable of inducing a pressure rise rate which stimulates the ignition transient that occurs during launch. Dynamic loads are applied during the pressure cycle to simulate external tank attach (ETA) strut loads present on the ETA ring. Sealing ability of the redesigned joints is evaluated under joint movement conditions produced by these combined loads since joint sealing ability depends on seal resilience velocity being greater than gap opening velocity. Also, maximum flight dynamic loads are applied to the test article which is either pressurized to 600 psia using gaseous nitrogen (GN2) or applied to the test article as the pressure decays inside the test article on the down cycle after the ignition transient cycle. This new test facility is examined with respect to its capabilities. In addition, both the topic of test effectiveness versus space vehicle flight performance and new aerospace test techniques, as well as a comparison between the old SRM design and the RSRM are presented.

Vibbart, Charles M.↗
NASA NTRS1989

Transient X-rays, gamma-rays and neutrons in space

The various astrophysical sources of transient X-ray, gamma-ray, and neutron emission which can produce significant increases in the high-energy (greater than 1 keV) radiation and particle background flux in space. These sources include solar flares, gamma-ray bursts, supernovae, and other astrophysical transients. The observations of these sources are reviewed, and the expected rate of occurrence of their transient emission is examined as a function of intensity and energy.

Lingenfelter, R. E.↗
NASA NTRS1989

Transient and steady inertially tethered clouds of gas in a vacuum

The generation, formation, and dissipation of a transient cloud of gas produced by a multiorifice ring jet are experimentally studied, and the results are compared to a long-term steady-state flow. The transient case is related to the steady-state case by comparison of their respective number density distributions in the flowfield. The shapes of the clouds are also observed and compared to the shape of the theoretical collisionless cloud. The results indicate that the steady-state cloud is concentrated into a smaller volume than the transient cloud, which tends to spread out farther radially as well as upstream. These differences seem to indicate that a surprisingly long time is required to attain steady flow, which may be due to a long-term buildup of collision products.

Farnham, Tony L.↗
NASA NTRS1989

Analysis of the transient compressible vapor flow in heat pipes

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual vapor flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds and high mass flow rates are successfully predicted. The one-dimensional model also describes the vapor flow dynamics in cylindrical heat pipes at high temperatures.

Jang, J. H.↗
NASA NTRS1990

Integrated model of G189A and Aspen-plus for the transient modeling of extravehicular activity atmospheric control systems

A computerized modeling tool, under development for the transient modeling of an extravehicular activity atmospheric control subsystem is described. This subsystem includes the astronaut, temperature control, moisture control, CO2 removal, and oxygen make-up components. Trade studies evaluating competing components and subsystems to guide the selection and development of hardware for lunar and Martian missions will use this modeling tool. The integrated modeling tool uses the Advanced System for Process Engineering (ASPEN) to accomplish pseudosteady-state simulations, and the general environmental thermal control and life support program (G189A) to manage overall control of the run and transient input output, as well as transient modeling computations and database functions. Flow charts and flow diagrams are included.

Kolodney, Matthew↗
NASA NTRS1990

Analog-digital simulation of transient-induced logic errors and upset susceptibility of an advanced control system

A simulation study is described which predicts the susceptibility of an advanced control system to electrical transients resulting in logic errors, latched errors, error propagation, and digital upset. The system is based on a custom-designed microprocessor and it incorporates fault-tolerant techniques. The system under test and the method to perform the transient injection experiment are described. Results for 2100 transient injections are analyzed and classified according to charge level, type of error, and location of injection.

Carreno, Victor A.↗
NASA NTRS1989

Analysis of the transient calibration of heat flux sensors: One dimensional case

The effect of transient heat flux on heat flux sensor response and calibration is analyzed. A one dimensional case was studied in order to elucidate the key parameters and trends for the problem. It has the added advantage that the solutions to the governing equations can be obtained by analytic means. The analytical results obtained to date indicate that the transient response of a heat flux sensor depends on the thermal boundary conditions, the geometry and the thermal properties of the sensor. In particular it was shown that if the thermal diffusivity of the sensor is small, then the transient behavior must be taken into account.

Dybbs, A.↗
NASA NTRS1991

The performance of cable braids and terminations to lightning induced transients

The latest specification detailing the test waveforms for indirect lightning transients as applied to aircraft wiring systems specify very high voltages and currents. Although considerable data exists for measuring cable screen leakage using such methods as surface transfer impedance and bulk cable injection, there is little data on the likely core transient level that is likely to be induced from these threats. In particular, the new Waveform 5 at very high current levels (10 kA) is reputed to cause severe cable damage. A range of representative cables were made with various screen termination techniques and screening levels. These were tested first to determine their relative screening performance and then they were subjected to lightning transient testing to all the specified waveforms. Core voltages were measured for each test. Tests were also performed on bundles with fewer wires to determine the failure criteria with Waveform 5 and these tests also include flat conductor cables. The test showed that correctly terminated cable bundles performed well in all the tests and would provide a high level of protection to the electronic systems. The use of overbraides, provided the individual screens are well terminated, appears to be unnecessary.

Crofts, David↗
NASA NTRS1991

Diffuse dispersive delay and the time convolution/attenuation of transients

Test data and analytic evaluations are presented to show that relatively poor 100 KHz shielding of 12 Db can effectively provide an electromagnetic pulse transient reduction of 100 Db. More importantly, several techniques are shown for lightning surge attenuation as an alternative to crowbar, spark gap, or power zener type clipping which simply reflects the surge. A time delay test method is shown which allows CW testing, along with a convolution program to define transient shielding effectivity where the Fourier phase characteristics of the transient are known or can be broadly estimated.

Bittner, Burt J.↗
NASA NTRS1991

Transient cryogenic liquid discharge in normal and micro-gravity

Transient discharge of liquid cryogens from partially filled tanks under microgravity is considered. The discharge is made to a low-pressure site through a straight tube. The ultimate objective of the study is to predict the transient mass flow rate. In addition, the pressure history in the tank is of interest, since the pressure falls below the triple point toward the end of the dump, causing solidification in the tank and/or the discharge line. As first steps, experiments have been performed in normal gravity and attempts are made to predict the transient rate and pressure history under this condition. Experiments are performed with liquid nitrogen dumped to sites with pressures below the triple point. Homogeneous equilibrium and nonequilibrium two-phase critical flow models are compared to the experimental results. Equilibrium and nonequilibrium tank pressure history models are also compared to experimental data.

Purwin, T. P.↗
NASA NTRS1990

Single event induced transients in I/O devices - A characterization

The results of single-event upset (SEU) testing performed to evaluate the parametric transients, i.e., amplitude and duration, in several I/O devices, and the impact of these transients are discussed. The failure rate of these devices is dependent on the susceptibility of interconnected devices to the resulting transient change in the output of the I/O device. This failure rate, which is a function of the susceptibility of the interconnected device as well as the SEU response of the I/O device itself, may be significantly different from an upset rate calculated without taking these factors into account. The impact at the system level is discussed by way of an example.

Newberry, D. M.↗
NASA NTRS1991

Transient response of a high-capacity heat pipe for Space Station Freedom

High-capacity heat pipe radiator panels have been proposed as the primary means of heat rejection for Space Station Freedom. In this system, the heat pipe would interface with the thermal bus condensers. Changes in system heat load can produce large temperature and heat load variations in individual heat pipes. Heat pipes could be required to start from an initially cold state, with heat loads temporarily exceeding their low-temperature transport capacity. The present research was motivated by the need for accurate prediction of such transient operating conditions. In this work, the cold startup of a 6.7-meter long high-capacity heat pipe is investigated experimentally and analytically. A transient thermohydraulic model of the heat pipe was developed which allows simulation of partially-primed operation. The results of cold startup tests using both constant temperature and constant heat flux evaporator boundary conditions are shown to be in good agreement with predicted transient response.

Ambrose, J. H.↗
NASA NTRS1991

Analysis of the one-dimensional transient compressible vapor flow in heat pipes

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual vapor flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds as well as high mass flow rates are successfully predicted.

Jang, Jong H.↗
NASA NTRS1991

A new technique to study transient conductivity under pulsed monochromatic light in Cr-doped GaAs using acoustoelectric voltage measurement

The transient conductivity of high-resistivity Bridgman-grown Cr-doped GaAs under pulsed monochromatic light is monitored using transverse acoustoelectric voltage (TAV) at 83 K. Keeping the photon flux constant, the height and transient time constant at the TAV are used to calculate the energy dependence of the trap density and its cross section, respectively. Two prominent trap profiles with peak trap densities of approximately 10 to the 17th/cu cm eV near the valence and the conduction bands are detected. These traps have very small capture cross sections in the range of 10 to the -23 to 10 to the -21st cm sq. A phenomenon similar to the persistent photoconductivity with transient time constants in excess of a few seconds in high-resistivity GaAs at T = 83 K is also detected using this technique. These long relaxation times are readily explained by the spatial separation of the photo-excited electron-hole pairs and the small capture cross section and large density of trap distribution near the conduction band.

Tabib-Azar, Massood↗
NASA NTRS1991

Finite difference time domain calculation of transients in antennas with nonlinear loads

Determining transient electromagnetic fields in antennas with nonlinear loads is a challenging problem. Typical methods used involve calculating frequency domain parameters at a large number of different frequencies, then applying Fourier transform methods plus nonlinear equation solution techniques. If the antenna is simple enough so that the open circuit time domain voltage can be determined independently of the effects of the nonlinear load on the antennas current, time stepping methods can be applied in a straightforward way. Here, transient fields for antennas with more general geometries are calculated directly using Finite Difference Time Domain (FDTD) methods. In each FDTD cell which contains a nonlinear load, a nonlinear equation is solved at each time step. As a test case, the transient current in a long dipole antenna with a nonlinear load excited by a pulsed plane wave is computed using this approach. The results agree well with both calculated and measured results previously published. The approach given here extends the applicability of the FDTD method to problems involving scattering from targets, including nonlinear loads and materials, and to coupling between antennas containing nonlinear loads. It may also be extended to propagation through nonlinear materials.

Luebbers, Raymond J.↗