Search NASA⌕ Search

SEARCH · Search NASA

Results for “vortex generators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Turbulent flow separation control through passive techniques

Several passive separation control techniques for controlling moderate two-dimensional turbulent flow separation over a backward-facing ramp are studied. Small transverse and swept grooves, passive porous surfaces, large longitudinal grooves, and vortex generators were among the techniques used. It was found that, unlike the transverse and longitudinal grooves of an equivalent size, the 45-deg swept-groove configurations tested tended to enhance separation.

Lin, J. C.↗

Experimental investigation of flow about a strut-endwall configuration

An experimental study was conducted to investigate incompressible flow about a strut-endwall configuration positioned within a constant area duct. The endwal boundary layer was tripped, but natural transition occurred on the strut surface. The results indicate that spanwise varying transition on this surface leads to the formation of a secondary vortex which coexists with the horseshoe vortex generated by endwall flow separation upstream of the strut leading edge. Both vortices are similar in strength downstream of the strut trailing edge, and both distort the primary flow and local turbulence structure in the wake-endwall region. The level of distortion is demonstrated by means of axial mean velocity contours, turbulence kinetic energy contours, and Reynolds shear stress contours measured in the cross plane at two streamwise locations. Analysis of the results shows that conventional eddy viscosity and k-epsilon transport equation models are not wholly adequate for predicting this flow situation.

Chang, P. S.↗

Drag reduction in nature

Recent studies on the drag-reducing shapes, structures, and behaviors of swimming and flying animals are reviewed, with an emphasis on potential analogs in vehicle design. Consideration is given to form drag reduction (turbulent flow, vortex generation, mass transfer, and adaptations for body-intersection regions), skin-friction drag reduction (polymers, surfactants, and bubbles as surface 'additives'), reduction of the drag due to lift, drag-reduction studies on porpoises, and drag-reducing animal behavior (e.g., leaping out of the water by porpoises). The need for further research is stressed.

Bushnell, D. M.↗

Inlets, ducts, and nozzles

The internal fluid mechanics research program in inlets, ducts, and nozzles consists of a balanced effort between the development of computational tools (both parabolized Navier-Stokes and full Navier-Stokes) and the conduct of experimental research. The experiments are designed to better understand the fluid flow physics, to develop new or improved flow models, and to provide benchmark quality data sets for validation of the computational methods. The inlet, duct, and nozzle research program is described according to three major classifications of flow phenomena: (1) highly 3-D flow fields; (2) shock-boundary-layer interactions; and (3) shear layer control. Specific examples of current and future elements of the research program are described for each of these phenomenon. In particular, the highly 3-D flow field phenomenon is highlighted by describing the computational and experimental research program in transition ducts having a round-to-rectangular area variation. In the case of shock-boundary-layer interactions, the specific details of research for normal shock-boundary-layer interactions are described. For shear layer control, research in vortex generators and the use of aerodynamic excitation for enhancement of the jet mixing process are described.

Abbott, John M.↗

Ultra high bypass Nacelle aerodynamics inlet flow-through high angle of attack distortion test

A flow-through inlet test program was conducted to evaluate inlet test methods and determine the impact of the fan on inlet separation when operating at large angles of attack. A total of 16 model configurations of approximately 1/6 scale were tested. A comparison of these flow-through results with powered data indicates the presence of the fan increased separation operation 3 degrees to 4 degrees over the flow through inlet. Rods and screens located at the fan face station, that redistribute the flow, achieved simulation of the powered-fan results for separation angle of attack. Concepts to reduce inlet distortion and increase angle of attack capability were also evaluated. Vortex generators located on the inlet surface increased inlet angle of attack capability up to 2 degrees and reduced inlet distortion in the separated region. Finally, a method of simulating the fan/inlet aerodynamic interaction using blockage sizing method has been defined. With this method, a static blockage device used with a flow-through model will approximate the same inlet onset of separation angle of attack and distortion pattern that would be obtained with an inlet model containing a powered fan.

Larkin, Michael J.↗

Time accurate Navier-Stokes computations of solid rocket motor internal field joint cavity flows

The low-speed flow of combustion gases in the Space Shuttle Solid Rocket Motor (SRM) following ignition are investigated with a time-accurate CFD technique. The flow of the combustion gases is examined in the forward joint section of the SRM at 80 s after ignition with attention given to the amplification of existing 'organ-pipe' modes of 15, 30, and 45 Hz resulting from frequency lock-in with vortex-shedding modes. The CFD code employed is a multizone compressible Navier-Stokes flow solver using a finite-volume, upwind-biased, total-variation-diminishing scheme. The vortex-generated oscillations generated by the inhibitor and the cavity at the forward field joint are described in terms of amplitude and frequency and related to the flow dynamics in the SRM. Oscillations are shown to occur spontaneously when the trailing edge of the cavity at the joint is sharp and can be amplified if the unburned portion of the inhibitor protrudes into the flow.

Farr, Rebecca A.↗

NASA. Lewis Research Center/IFMD inlet duct and nozzle high speed validation experiments

Personnel from NASA Lewis Research Center spoke on the subject of inlet duct and nozzle high speed validation experiments to include crossing shocks and boundary layer interaction, unsteady shock/boundary layer interactions, and vortex generators. Attention was also paid to the subjects of high speed mixing and transition ducts. Specific application was made to the NASP hypermixing concepts.

Hingst, Warren↗

Underwing Compression Vortex-Attenuation Device

Underwing compression vortex-attenuation device designed to provide method for attenuating lift-induced vortex generated by wings of airplane. Includes compression panel attached to lower surface of wing, facing perpendicular to streamwise airflow. Concept effective on all types of aircraft. Causes increase in wing lift rather than reduction when deployed. Device of interest to aircraft designers and enhances air safety in general.

James C Patterson Jr.↗

Aerodynamic flight control to increase payload capability of future launch vehicles

In this report, we provide some examples of French, Russian, Chinese, and Japanese launch vehicles that have utilized fins in their designs. Next, the aerodynamic design of the fins is considered in Section 3. Some comments on basic static stability and control theory are followed by a brief description of an aerodynamic characteristics prediction code that was used to estimate the characteristics of a modified NLS 1.5 Stage vehicle. Alternative fin designs are proposed and some estimated aerodynamic characteristics presented and discussed. Also included in Section 3 is a discussion of possible methods of enhancement of the aerodynamic efficiency of fins, such as vortex generators and jet flaps. We consider the construction of fins for launch vehicles in Section 4 and offer an assessment of the state-of-the-art in the use of composites for aerodynamic control surfaces on high speed vehicles. We also comment on the use of smart materials for launch vehicle fins. The dynamic stability and control of a launch vehicle that utilizes both thrust vector control (engine nozzle gimballing) and movable fins is the subject addressed in Section 5. We give a short derivation of equations of motion for a launch vehicle moving in a vertical plane above a spherical earth, discuss the use of a gravity-turn nominal trajectory, and give the form of the period equations linearized about such a nominal. We then consider feedback control of vehicle attitude using both engine gimballing and fin deflection. Conclusions are stated and recommendations made in Section 6. An appendix contains aerodynamic data in tabular and graphical formats.

Cochran, John E., Jr.↗

Several examples where turbulence models fail in inlet flow field analysis

Computational uncertainties in turbulence modeling for three dimensional inlet flow fields include flows approaching separation, strength of secondary flow field, three dimensional flow predictions of vortex liftoff, and influence of vortex-boundary layer interactions; computational uncertainties in vortex generator modeling include representation of generator vorticity field and the relationship between generator and vorticity field. The objectives of the inlet flow field studies presented in this document are to advance the understanding, prediction, and control of intake distortion and to study the basic interactions that influence this design problem.

Anderson, Bernhard H.↗

Impact disturbance of the Venus atmosphere

Experimental simulations of the atmosphere-surface interaction during high-velocity impact are presented. At Venus an atmospheric vortex, generated with impact, may interact with a local wind. Some surface features, observed on Magellan images may be related with the simulated effect.

Provalov, A. A.↗

Unsteady separation process and vorticity balance on unsteady airfoils

Low momentum fluid erupts at the unsteady separation region and forms a local shear layer at the viscous-inviscid interface. At the shear layer, the vorticity lumps into a vortex and protrudes into the inviscid region. This process initiates the separation process. The response of airfoils in unsteady free stream was investigated based on this vortex generation and convection concept. This approach enabled us to understand the complicated unsteady aerodynamics from a fundamental point of view.

Ho, Chih-Ming↗

Mechanisms of flow control with the unsteady bleed technique

The unsteady bleed technique (a.k.a. internal acoustic forcing) has been shown to be an effective method for control of separation on low Reynolds number airfoils, blunt-end cylinders aligned axially with the flow, cylinders aligned perpendicular to the flow, and forebody geometries at high angles of attack. In many of these investigations, the mechanism for the control has been attributed to enhancement of the shear layer (Kelvin-Helmholtz) instability by the unsteady component of the forcing. However, this is not the only possible mechanism, nor may it be the dominant mechanism under some conditions. In this work it is demonstrated that at least two other mechanisms for flow control are present, and depending on the location and the amplitude of the forcing, these may have significant impact on the flow behavior. Experiments were conducted on a right-circular cylinder with a single unsteady bleed slot aligned along the axis of the cylinder. The effects of forcing frequency, forcing amplitude, and slot location on the azimuthal pressure distribution were studied. The results suggest that a strong vortical structure forms near the unsteady bleed slot when the slot location is upstream of the boundary layer separation point. The structure is unsteady, since it is created by the unsteady forcing. The 'vortex' generates a sizeable pressure spike (C(sub p) = -3.0) in the time-averaged pressure field immediately downstream of the slot. In addition to the pressure spike, the boundary layer separation location moves farther downstream when the forcing is activated. Delay of the separation is believed to be a result of enhancing the Kelvin-Helmholtz instability. When forcing is applied in a quiescent wind tunnel, a weak low-pressure region forms near the slot that is purely the result of the second-order streaming effect.

Williams, D. R.↗

Investigation of ramp injectors for supersonic mixing enhancement

A comparative study of wall mounted swept ramp injectors fitted with injector nozzles of different shape has been conducted in a constant area duct to explore mixing enhancement techniques for scramjet combustors. Six different injector nozzle inserts, all having equal exit and throat areas, were tested to explore the interaction between the preconditioned fuel jet and the vortical flowfield produced by the ramp: circular nozzle (baseline), nozzle with three downstream facing steps, nozzle with four vortex generators, elliptical nozzle, tapered-slot nozzle, and trapezoidal nozzle. The main flow was air at Mach 2, and the fuel was simulated by air injected at Mach 1.63 or by helium injected at Mach 1.7. Pressure and temperature surveys, combined with Mie and Rayleigh scattering visualization, were used to investigate the flow field. The experiments were compared with three dimensional Navier-Stokes computations. The results indicate that the mixing process is dominated by the streamwise vorticity generated by the ramp, the injectors' inner geometry having a minor effect. It was also found that the injectant/air mixing in the far-field is nearly independent of the injector geometry, molecular weight of the injectant, and the initial convective Mach number.

Haimovitch, Y.↗

Study of compressible flow through a rectangular-to-semiannular transition duct

Detailed flow field measurements are presented for compressible flow through a diffusing rectangular-to-semiannular transition duct. Comparisons are made with published computational results for flow through the duct. Three-dimensional velocity vectors and total pressures were measured at the exit plane of the diffuser model. The inlet flow was also measured. These measurements are made using calibrated five-hole probes. Surface oil flow visualization and surface static pressure data were also taken. The study was conducted with an inlet Mach number of 0.786. The diffuser Reynolds based on the inlet centerline velocity and the exit diameter of the diffuser was 3,200,000. Comparison of the measured data with previously published computational results are made. Data demonstrating the ability of vortex generators to reduce flow separation and circumferential distortion is also presented.

Foster, Jeffry↗

The future of very large subsonic transports

The Very Large Subsonic Transport (VLST) is a multi-use commercial passenger, commercial cargo, and military airlifter roughly 50% larger than the current Lockheed C-5 and Boeing 747. Due to the large size and cost of the VLST, it is unlikely that the commercial market can support more than one aircraft production line, while declining defense budgets will not support a dedicated military VLST. A successful VLST must therefore meet airline requirements for more passenger and cargo capacity on congested routes into slot-limited airports and also provide a cost effective heavy airlift capacity to support the overseas deployment of US military forces. A successful VLST must satisfy three key missions: commercial passenger service with nominal seating capacity at a minimum of 650 passengers with a range capability of 7,000 to 10,000 miles; commercial air cargo service for containerized cargo to support global manufacturing of high value added products, 'just-in-time' parts delivery, and the general globalization of trade; and military airlift with adequate capacity to load current weapon systems, with minimal break-down, over global ranges (7,000 to 10,000 miles) required to reach the operational theater without need of overseas bases and midair refueling. The development of the VLST poses some technical issues specific to large aircraft, but also key technologies applicable to a wide range of subsonic transport aircraft. Key issues and technologies unique to the VLST include: large composite structures; dynamic control of a large, flexible structure; aircraft noise requirements for aircraft over 850,000 pounds; and increased aircraft separation due to increased wake vortex generation. Other issues, while not unique to the VLST, will critically impact the ability to build an efficient and affordable aircraft include: active control systems: Fly-By-Light/Power-By-Wire (FBL/PBW); high lift systems; flight deck associate systems; laminar flow; emergency egress; and modular design. The VLST will encounter severe restrictions on weight, ground flotation, span, length, and door height to operate at current airports/bases, gates, and cargo loading systems. One option under consideration is for a sea-based VLST, either a conventional seaplane or Wing-In-Ground effect (WIG) vehicle, which would allow greater operational flexibility, while introducing other design challenges such as water impact loads and salt-water corrosion. Lockheed Martin is currently developing a floatplane version of the C-130 Hercules which will provide experience with a modern sea-based aircraft. In addition to its own ongoing research activities, Lockheed Martin is also participating in the NASA Advanced Subsonic Technology, High Speed Research (HSR), and other programs which address some of the technologies needed for the VLST. The VLST will require NASA and US aerospace companies to work together to develop new capabilities and technologies for make the VLST a viable part of transportation beyond 2000.

Justice, R. Steven↗

Jet Evolution Visualized and Quantified Using Filtered Rayleigh Scattering

Filtered Rayleigh scattering was utilized as a flow diagnostic in an investigation of a method for enhancing mixing in supersonic jets. The primary objectives of the study were to visualize the effect of vortex generating tabs on supersonic jets, to exact quantitative data from these planar visualizations, and to detect the presence of secondary flows (i.e., streamwise vorticity) generated by the tabs. An injection seeded frequency-doubled Nd:YAG was the light source and a 14 bit Princeton Instruments iodine charge coupled display (ICCD) camera recorded the image through an iodine cell. The incident wave length of the laser was held constant for each flow case so that the filter absorbed unwanted background light, but permitted part of the thermally broadened Rayleigh scattering light to pas through. The visualizations were performed for axisymmetric jets (D=1.9 cm) operated at perfectly expanded conditions for Mach 1.0, 1.5, and 2.0. All data were recorded for the jet cross section at x/D=3. One hundred instantaneous images were recorded and averaged for each case, with a threshold set to eliminate unavoidable particulate scattering. A key factor in these experiments was that the stagnation air was heated such that the expansion of the flow in the nozzle resulted in the static temperature in the jet being equal to the ambient temperature, assuming isentropic flow. Since the thermodynamic conditions of the flow were approximately the same for each case, increases in the intensity recorded by the ICCD camera could be directly attributed to the Doppler shift, and hence velocity. Visualizations were performed for Mach 1.5 and Mach 2.0 jets with tabs inserted at the nozzle exit. The distortion of the jet was readily apparent and was consistent with Mie scattering-based visualizations. Asymmetry in the intensities of the images indicate the presence of secondary flow patterns which are consistent with the streamwise vortices measured using more traditional diagnostics in subsonic jets with the same tab configurations. Because each tab causes shocks to form, the assumption of isentropic flow is not valid for these cases. However, within a reasonable first-order estimation,the intensity across the illuminated plane for these cases can be related to a value combining density and velocity.

Reeder, Mark F.↗