Search NASA⌕ Search

SEARCH · Search NASA

Results for “wing sections”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Structural testing of the technology integration box beam

A full scale section of a transport aircraft wing box was designed, analyzed, fabricated, and tested. The wing box section, which was called the technology integration box beam, contained blade stiffened covers and T-stiffened channel spars constructed using graphite-epoxy materials. Covers, spars, and the aluminum ribs were assembled using mechanical fasteners. The box beam was statically tested for several loading conditions to verify the stiffness and strength characteristics of the composite wing design. Failure of the box beam occurred at 125 pct. of design limit load during the combined unbending and torsion ultimate design load test. It appears that the failure initiated at a stiffener runout location in the upper cover which resulted in rupture of the upper cover and portions of both spars.

Griffin, C. F.↗
NASA NTRS1949

Investigations at supersonic speeds of 22 triangular wings representing two airfoil sections for each of 11 apex angles

Data obtained from wind tunnel investigations of two series of 11 triangular wings conducted at Mach numbers of 1.62, 1.92, and 1.40 to determine the effect of leading-edge shape and to compare actual test values with the nonviscous linear theory are presented. The two series of wings had identical plan forms, a constant thickness ratio of 8 percent, a constant location of maximum-thickness point of 18 percent, and a range of apex half-angles from 10 degrees to forty-five degrees. The first series has an elliptical leading edge and the second series a wedge leading edge. Measurements were made of lift, drag, pitching moment, and pressure distribution, the latter being confined to three wings at one Mach number.

Love, Eugene S↗
NASA NTRS1972

Space shuttle orbiter reentry flow field and heating analysis

The reentry flow field and thermal environment around the straight wing shuttle orbiter vehicle were determined. Both rarefied and continuum flow fields and associated heating rates on various configurations representative of the orbiter at high angle of attack were calculated. Rarefied flow fields and heating rates were computed by the Monte Carlo direct simulation technique for altitudes above 82.3 km. Continuum inviscid flow fields were calculated by 2-D unsteady and 3-D steady finite difference/artificial viscosity methods and also by a 2-D shock layer analysis technique. Viscous flow fields and heating rates in the continuum regime were computed by a boundary layer integral matrix method for laminar flow and by an aerodynamic surface heating technique for turbulent flow. Shapes considered in the study included flat plates (representing the underside of the orbiter fuselage or the wing MAC), orbiter fuselage cross sections, orbiter wing airfoils, and 3-D orbiter configurations, all at high angle of attack (40 - 60 deg). The theoretical results showed good agreement with measured pressure and heat transfer data.

Rochelle, W. C.↗
NASA NTRS1992

Improvements to the missile aerodynamic prediction code DEMON3

The computer program DEMON3 was developed for the aerodynamic analysis of nonconventional supersonic configurations comprising a body with noncircular cross section and up to two wing or fin sections. Within a wing or fin section, the lifting surfaces may be cruciform, triform, planar, or low profile layouts; the planforms of the lifting surfaces allow for breaks in sweep. The body and fin sections are modeled by triplet and constant u-velocity panels, respectively, accounting for mutual body-fin interference. Fin thickness effects are included for the use of supersonic planar source panels. One of the unique features of DEMON3 is the modeling of high angle of attack vortical effects associated with the lifting surfaces and the body. In addition, shock expansion and Newtonian pressure calculation methods can be optionally engaged. These two dimensional nonlinear methods are augmented by aerodynamic interference determined from the linear panel methods. Depending on the geometric details of the body, the DEMON3 program can be used to analyze nonconventional configurations at angles of attack up to 25 degrees for Mach numbers from 1.1 to 6. Calculative results and comparisons with experimental data demonstrate the capabilities of DEMON3. Limitations and deficiencies are listed.

Dillenius, Marnix F. E.↗
NASA NTRS1951

Theoretical characteristics of two-dimensional supersonic control surfaces

The "Busemann second-order-approximation theory" for the pressure distribution over a two-dimensional airfoil in supersonic flow was used to determine some of the aerodynamic characteristics of uncambered symmetrical parabolic and double-wedge airfoils with leading-edge and trailing-edge flaps. The characteristics presented and discussed in this paper are: flap effectiveness factor, rate of change of hinge-moment coefficient with flap deflection, rate of change of the pitching-moment coefficient with flap deflection, rate of change of the pitching-moment coefficient about the mid chord with flap deflection, and the location of the center of pressure of the airfoil-flap combination.

MACH NUMBER EFFECTS - WING SECTIONS↗
NASA NTRS1987

Inviscid transonic wing design using inverse methods in curvilinear coordinates

An inverse wing design method has been developed around an existing transonic wing analysis code. The original analysis code, TAWFIVE, has as its core the numerical potential flow solver, FLO30, developed by Jameson and Caughey. Features of the analysis code include a finite-volume formulation; wing and fuselage fitted, curvilinear grid mesh; and a viscous boundary layer correction that also accounts for viscous wake thickness and curvature. The development of the inverse methods as an extension of previous methods existing for design in Cartesian coordinates is presented. Results are shown for inviscid wing design cases in super-critical flow regimes. The test cases selected also demonstrate the versatility of the design method in designing an entire wing or discontinuous sections of a wing.

Gally, Thomas A.↗
NASA NTRS1989

Development of direct-inverse 3-D methods for applied transonic aerodynamic wing design and analysis

An inverse wing design method was developed around an existing transonic wing analysis code. The original analysis code, TAWFIVE, has as its core the numerical potential flow solver, FLO30, developed by Jameson and Caughey. Features of the analysis code include a finite-volume formulation; wing and fuselage fitted, curvilinear grid mesh; and a viscous boundary layer correction that also accounts for viscous wake thickness and curvature. The development of the inverse methods as an extension of previous methods existing for design in Cartesian coordinates is presented. Results are shown for inviscid wing design cases in super-critical flow regimes. The test cases selected also demonstrate the versatility of the design method in designing an entire wing or discontinuous sections of a wing.

Carlson, Leland A.↗
NASA NTRS1954

Effect of Ice Formations on Section Drag of Swept NACA 63A-009 Airfoil with Partical-span Leading-edge Slat for Various Modes of Thermal Ice Protection

Studies were made to determine the effect of ice formations on the section drag of a 6.9-foot-chord 36 degree swept NACA 63A-009 airfoil with partial-span leading-edge slat. In general, the icing of a thin swept airfoil will result in greater aerodynamic penalties than for a thick unswept airfoil. Glaze-ice formations at the leading edge of the airfoil caused large increases in section drag even at liquid-water content of 0.39 gram per cubic meter. The use of an ice-free parting strip in the stagnation region caused a negligible change in drag compared with a completely unheated airfoil. Cyclic de-icing when properly applied caused the drag to decrease almost to the bare-airfoil drag value.

PROTUBERANCES - BODIES↗
NASA NTRS1986

Vertical drop test of a transport fuselage section located aft of the wing

A 12-foot long Boeing 707 aft fuselage section with a tapering cross section was drop tested at the NASA Langley Research Center to measure structural, seat, and occupant response to vertical crash laods and to provide data for nonlinear finite element modeling. This was the final test in a series of three different transport fuselage sections tested under identical conditions. The test parameters at impact were: 20 ft/s velocity, and zero pitch, roll, and yaw. In addition, the test was an operational shock test of the data acquisition system used for the Controlled Impact Demonstration (CID) of a remotely piloted Boeing 720 that was crash tested at NASA Ames Dryden Flight Research Facility on December 1, 1984. Post-test measurements of the crush showed that the front of the section (with larger diameter) crushed vertically approximately 14 inches while the rear crushed 18 inches. Analysis of the data traces indicate the maximum peak normal (vertical) accelerations at the bottom of the frames were approximately 109 G at body station 1040 and 64 G at body station 1120. The peak floor acceleration varied from 14 G near the wall to 25 G near the center where high frequency oscillations of the floor were evident. The peak anthropomorphic dummy pelvis normal (vertical) acceleration was 19 G's.

Fasanella, E. L.↗
NASA NTRS1990

Numerical study of the effects of icing on finite wing aerodynamics

The sectional and total aerodynamics load characteristics of moderate aspect ratio wings with and without simulated glaze leading-edge ice are studied using a three-dimensional, compressible Navier-Stokes solver. The wing has an untwisted, untapered planform shape with NACA 0012 airfoil section. The aspect ratio of the wing is chosen to be 5. Comparisons of computed surface pressures and sectional loads with experimental data for identical configurations are given. The abrupt decrease in the wing stall angle as a result of the leading edge ice formation is numerically demonstrated.

Kwon, Oh J.↗
NASA NTRS1952

Transition caused by the laminar flow separation

An experimental investigation of the effects of the geometry of body surface, Reynolds number, stream turbulence, and a roughness element (wire) on the reattachment of separated laminar boundary-layer flow on a bent flat plate is presented and discussed. The flow mechanisms determining reattachment of the boundary layer are analyzed and discussed.

BOUNDARY LAYER CHARACTERISTICS - WING SECTIONS↗
NASA NTRS1984

Optimal redesign study of the harm wing

The purpose of this project was to investigate the use of optimization techniques to improve the flutter margins of the HARM AGM-88A wing. The missile has four cruciform wings, located near mid-fuselage, that are actuated in pairs symmetrically and antisymmetrically to provide pitch, yaw, and roll control. The wings have a solid stainless steel forward section and a stainless steel crushed-honeycomb aft section. The wing restraint stiffness is dependent upon wing pitch amplitude and varies from a low value near neutral pitch attitude to a much higher value at off-neutral pitch attitudes, where aerodynamic loads lock out any free play in the control system. The most critical condition for flutter is the low-stiffness condition in which the wings are moved symmetrically. Although a tendency toward limit-cycle flutter is controlled in the current design by controller logic, wing redesign to improve this situation is attractive because it can be accomplished as a retrofit. In view of the exploratory nature of the study, it was decided to apply the optimization to a wing-only model, validated by comparison with results obtained by Texas Instruments (TI). Any wing designs that looked promising were to be evaluated at TI with more complicated models, including body modes. The optimization work was performed by McIntosh Structural Dynamics, Inc. (MSD) under a contract from TI.

Mcintosh, S. C., Jr.↗
NASA NTRS1950

Large-Scale Flight Measurements of Zero-Lift Drag at Mach Numbers from 0.90 to 1.95 of 1/14-Scale Model of the Northrop MX-775B Pilotless Aircraft with Small Body

A flight test was made a t high subsonic, transonic, and supersonic speeds and at high Reynolds numbers to determine the zero-lift drag of a 1/14-scale model of the Northrop MX-775B pilotless aircraft with small small body. The triangular wing of the model had 67.5 deg leading-edge sweep and 15 deg. trailing-edge sweep, The wing airfoil sections were modified NACA 0004 sections. The drag coefficient based on total wing area was 0.0107 at Mach number 1.60. At transonic speeds the maximum drag coefficient was 0.0125. The force-break Mach number was 0,98.

Gillespie, Warren, Jr.↗
NASA NTRS1973

An experimental investigation of three oblique-wing and body combinations at Mach numbers between 0.60 and 1.40

An experimental investigation was conducted in an 11- by 11-foot transonic wind tunnel to determine the aerodynamic characteristics of three oblique high aspect ratio wings in combination with a high fineness-ratio Sears-Haack body. The three wings had the same elliptical planform and base line curvature but had different airfoil sections. One wing had an airfoil section designed to have a lift coefficient of 1.0 at a Mach number of 0.7, another to have shock-free supersonic flow over the upper surface, and the other to have a lift coefficient of 1.3 at a Mach number of 0.6. Longitudinal and lateral-directional stability data were obtained at wing yaw angles of 0 deg, 45 deg, 50 deg, and 60 deg over a test Mach number range from 0.6 to 1.4 for angles of attack between minus 7 deg and 9 deg. Reynolds numbers for the study were 4 and 6 million per foot. Flow-visualization studies were made to examine the nature of the flow on the wing surfaces. Notable differences were found in the aerodynamic characteristics of the three wing-body combinations, particularly in the lateral-directional characteristics.

Graham, L. A.↗