Search NASA⌕ Search

SEARCH · Search NASA

Results for “(SrO)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

CVD silicon carbide monofilament reinforced SrO-Al2O3-2SiO2 (SAS) glass-ceramic composites

Unidirectional CVD SiC fiber-reinforced SrO.Al2O3.2SiO2 (SAS) glass-ceramic matrix composites have been fabricated by hot pressing at various combinations of temperature, pressure and time. Both carbon-rich surface coated SCS-6 and uncoated SCS-0 fibers were used as reinforcements. Almost fully dense composites have been obtained. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase observed in the matrix from x-ray diffraction. During three point flexure testing of composites, a test span to thickness ratio of approximately 25 or greater was necessary to avoid sample delamination. Strong and tough SCS-6/SAS composites having a first matrix crack stress of approximately 300 MPa and an ultimate bend strength of approximately 825 MPa were fabricated. No chemical reaction between the SCS-6 fibers and the SAS matrix was observed after high temperature processing. The uncoated SCS-0 fiber-reinforced SAS composites showed only limited improvement in strength over SAS monolithic. The SCS-0/SAS composite having a fiber volume fraction of 0.24 and hot pressed at 1400 deg C exhibited a first matrix cracking stress of approximately 231 +/- 20 MPa and ultimate strength of 265 +/- 17 MPa. From fiber push-out tests, the fiber/matrix interfacial debonding strength (tau(sub debond)) and frictional sliding stress (tau(sub friction)) in the SCS-6/SAS system were evaluated to be approximately 6.7 +/- 2.3 MPa and 4.3 +/- 0.6 MPa, respectively, indicating a weak interface. However, for the SCS-0/SAS composite, much higher values of approximately 17.5 +/- 2.7 MPa for tau(sub debond) and 11.3 +/- 1.6 MPa for tau(sub friction) respectively, were observed; some of the fibers were so strongly bonded to the matrix that they could not be pushed out. Examination of fracture surfaces revealed limited short pull-out length of SCS-0 fibers. The applicability of various micromechanical models for predicting the values of first matrix cracking stress and ultimate strength of these composites were examined.

Bansal, Narottam P.↗
DOE OSTI2025

Tailoring composition and deformation modes at the microstructural level for next generation low-cost high-strength austenitic stainless steels

The objective of this project is to enable deliberate development of cost-effective, hydrogen resistant alloys by establishing detailed relationships specific to the effects of alloy composition, short-range order (SRO), and microsegregation in the presence of hydrogen on the transition between homogeneous deformation and localized plasticity in shear bands. In collaboration with the International Institute for Carbon-Neutral Energy Research, I2CNER, at Kyushu University in Japan, we conceptualized, designed, and manufactured four austenitic alloys that maintain corrosion resistance and ensure lower cost relative to baseline commercial alloys. The mechanical properties and deformation modes of the novel alloys (KU alloys) were assessed in the presence of hydrogen (H). Correlations between composition and performance revealed that two of the KU alloys are suitable replacements for 316 steel, while another is a viable replacement for 304 steel at room temperature. We found that, in the presence of other austenite stabilizing elements namely Mn and N, replacing Ni with Cu does not lead to martensite formation as has been previously reported.1–3 Furthermore, we found that the addition of Cu leads to an earlier onset of multiple slip resulting in an relative earlier onset of a higher work hardening rate (WHR). Greater understanding of the relationships between alloy composition and SRO required the development of a novel advanced electron diffraction methodology to characterize SRO in complex FCC alloys. This innovative approach, which combines fluctuation and correlation analyses of diffuse-scattering signals, successfully differentiated between SRO and long-range ordering (LRO). Further investigations into annealed austenitic stainless steels could provide insights into manipulating SRO and its effects on material properties. Atomistic simulations provided understanding of SRO behavior that was difficult to capture experimentally. This project created the first spin cluster expansion model that is able to capture and describe SRO effects in Fe-Ni-Cr FCC alloys, accounting for the non-negligible effects of magnetism. An automated computational workflow was established to provide reliable predictions of SRO in Fe-Ni-Cr austenitic alloys, both with and without the presence of H atoms. Analysis of the propensity for SRO in Fe-Ni-Cr alloys revealed that H tends to cluster with specific, well-defined SRO domains. The computational framework is general purpose and can be extended to realistic stainless steels across diverse composition ranges. With confidence that SRO is possible in austenitic stainless steels, we developed a discrete dislocation finite element code to understand the interaction of dislocations with SRO in the presence of H. By incorporating H effects on the dislocation emission and SRO stress field we show that the critical stress for the dislocation pileup to breakthrough the SRO domain decreases in the presence of H, which directly contributes localized deformation at the macroscale. Through the simulation of a uniaxial tension test, we demonstrated that H-induced weakening of SRO stress field and H-enhanced dislocation emission can lead to the onset of shear localization at lower macroscopic strains. As a whole, this project identified three novel alloys that show improvements in performance and cost efficiency for H-facing applications by studying correlations between alloy chemistry and deformation behavior. We also made significant advancements to experimental and computational methodologies necessary to study the chemistry and distribution of SRO across a range of alloys, which in turn allowed us to demonstrate how deformation mechanisms change due to the contributions of SRO in austenitic alloys in the presence of H. The combined advancements in fundamental understanding with novel alloy development in this project has increased the viability of next generation H-technologies for the broader public through accessible low-cost alloys and accelerated development towards future H-infrastructure.

08 HYDROGEN↗
NASA NTRS2011

Short Range-Ordered Minerals: Insight into Aqueous Alteration Processes on Mars

Short range-ordered (SRO) aluminosilicates (e.g., allophane) and nanophase ferric oxides (npOx) are common SRO minerals derived during aqueous alteration of basaltic materials. NpOx refers to poorly crystalline or amorphous alteration products that can be any combination of superparamagnetic hematite and/or goethite, akaganeite, schwertmannite, ferrihydrite, iddingsite, and nanometer-sized ferric oxide particles that pigment palagonitic tephra. Nearly 30 years ago, SRO phases were suggested as alteration phases on Mars based on similar spectral properties for altered basaltic tephra on the slopes of Mauna Kea in Hawaii and Martian bright regions measured by Earth-based telescopes. Detailed characterization of altered basaltic tephra on Mauna Kea have identified a variety of alteration phases including allophane, npOx, hisingerite, jarosite, alunite, hematite, goethite, ferrihydrite, halloysite, kaolinite, smectite, and zeolites. The presence of npOx and other Fe-bearing minerals (jarosite, hematite, goethite) was confirmed by the M ssbauer Spectrometer onboard the Mars Exploration Rovers. Although the presence of allophane has not been definitely identified on Mars robotic missions, chemical analysis by the Spirit and Opportunity rovers and thermal infrared spectral orbital measurements suggest the presence of allophane or allophane-like phases on Mars. SRO phases form under a variety of environmental conditions on Earth ranging from cold and arid to warm and humid, including hydrothermal conditions. The formation of SRO aluminosilicates such as allophane (and crystalline halloysite) from basaltic material is controlled by several key factors including activity of water, extent of leaching, Si activity in solution, and available Al. Generally, a low leaching index (e.g., wet-dry cycles) and slightly acidic to alkaline conditions are necessary. NpOx generally form under aqueous oxidative weathering conditions, although thermal oxidative alteration may occasional be involved. The style of aqueous alteration (hydrolytic vs. acid sulfate) impacts which phases will form (e.g., oxides, oxysulfates, and oxyhydroxides). Knowledge on the formation processes of SRO phases in basaltic materials on Earth has allowed significant enhancement in our understanding of the aqueous processes at work on Mars. The 2011 Mars Science Laboratory (MSL) will provide an instrument suite that should improve our understanding of the mineralogical and chemical compositions of SRO phases. CheMin is an X-ray diffraction instrument that may provide broad X-ray diffraction peaks for SRO phases; e.g., broad peaks around 0.33 and 0.23 nm for allophane. Sample Analysis at Mars (SAM) heats samples and detects evolved gases of volatile-bearing phases including SRO phases (i.e., carbonates, sulfates, hydrated minerals). The Alpha Particle X-ray Spectrometer (APXS) and ChemCam element analyzers will provide chemical characterization of samples. The identification of SRO phases in surface materials on MSL will be challenging due to their nanocrystalline properties; their detection and identification will require utilizing the MSL instrument suite in concert. Ultimately, sample return missions will be required to definitively identify and fully characterize SRO minerals with state-of-the-art laboratory instrumentation back on Earth.

Ming, Douglas W.↗
DOE OSTI2023

Accurate prediction of short-range order and its effect on thermodynamic, structural, and electronic properties of disordered alloys: exemplified in archetypical Cu 3 Au

Electronic-structure methods based on density-functional theory (DFT) were used to quantify the effect of chemical short-range order (SRO) on thermodynamic, structural, and electronic properties of archetypal face-centered-cubic (fcc) Cu3Au alloy. We showed that SRO can be tuned to alter bonding and lattice dynamics (i.e., phonons) and detail how these properties are changed with SRO. Thermodynamically favorable SRO significantly improved the phase stability of fcc Cu3Au from -0.0343 eV-atom -1 to –0.0682 eV-atom -1 . We used our DFT-based linear-response theory to predict SRO and its electronic origin, and accurately estimate the observed transition temperature, ordering instability (L1 2 ), and Warren-Cowley SRO parameters, in agreement with experiments. The accurate prediction of real-space SRO gives an edge over computationally and resource intensive approaches such as monte-carlo methods or experiments, which will enable large scale molecular dynamic simulations by providing supercells with optimized SRO. Here we also analyzed phonon dispersion and estimated the vibrational entropy change (from 9kB at 300 K to 6kB at 100 K) in fcc Cu3Au. We established from SRO analysis that exclusion of chemical interactions may lead to a skewed view of true properties in chemically complex alloys. The first-principles methods described in this work are generally applicable to any arbitrary solid-solution alloys, including multi-principal-element alloys, therefore, holds promise for designing technologically useful materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rigorous computation of short-range order unifies its controversial effects in complex concentrated alloys

Direct experimental observations of chemical short-range order (SRO) in complex concentrated alloys (CCAs) have triggered high interest. However, the reported effects of SRO on yield stresses are controversial, and their atomic-scale mechanisms are elusive, which limits our ability to utilize SRO in alloy design. Here we tackle this challenge using an advanced computational approach that rigorously takes into account the critical lattice distortion in CCAs and further verify our theoretical predictions with experiments. We show that the CoCrNi model alloy has a narrow temperature window around 670 °C for SRO formation. This explains why the mechanical effect of SRO is observed in some experiments but not in others. Here, we propose an effective alloy-doping method to control SRO and reveal atomic-bonding types that dominate SRO formation for different alloys. The strategies and insights generally apply to a broad spectrum of alloys, laying the foundation for designing advanced alloys by manipulating their SRO.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Short- and medium-range orders in Al90Tb10 glass and their relation to the structures of competing crystalline phases

Molecular dynamics simulations using an interatomic potential developed by artificial neural network deep machine learning are performed to study the local structural order in Al90Tb10 metallic glass. We show that more than 80% of the Tb-centered clusters in Al90Tb10 glass have short-range order (SRO) with their 17 first coordination shell atoms stacked in a ‘3661’ or ‘15551’ sequence. Medium-range order (MRO) in Bergman-type packing extended out to the second and third coordination shells is also clearly observed. Analysis of the network formed by the ‘3661’ and ‘15551’ clusters show that ~82% of such SRO units share their faces or vertexes, while only ~6% of neighboring SRO pairs are interpenetrating. Such a network topology is consistent with the Bergman-type MRO around the Tb-centers. Moreover, crystal structure searches using genetic algorithm and the neural network interatomic potential reveal several low-energy metastable crystalline structures in the composition range close to Al 90 Tb 10 . Some of these crystalline structures have the ‘3661’ SRO while others have the ‘15551’ SRO. While the crystalline structures with the ‘3661’ SRO also exhibit the MRO very similar to that observed in the glass, the ones with the ‘15551’ SRO have very different atomic packing in the second and third shells around the Tb centers from that of the Bergman-type MRO observed in the glassy phase.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Modeling Short-Range Order in Disordered Rocksalt Cathodes by Pair Distribution Function Analysis

Pair distribution function (PDF) analysis is a powerful technique for the characterization of short-range order (SRO) in disordered materials. Accurate interpretation of experimental PDF data is critically reliant on the development of structural models that can account for local variations in site occupancies and bond lengths. To this end, we outline an approach to model SRO using first-principles calculations based on the cluster-expansion formalism. These methods are validated on neutron scattering data from two disordered rocksalt oxyfluorides, Li 1.3 Mn 0.4 Ti 0.3 O 1.7 F 0.3 and Li 1.3 Mn 0.4 Nb 0.2 Ti 0.1 O 1.7 F 0.3 . For each composition, we demonstrate that an average structure without any SRO fails to reproduce several key features in the experimental PDF. To pinpoint the origin of the suspected SRO in these materials, configurational and displacive effects were separately investigated using two disparate models. Special quasi-random structures were relaxed using density functional theory to account for local changes in bond lengths while maintaining a near-random ionic configuration. This leads to slightly improved accuracy but still misrepresents asymmetry in the first few peaks of the PDF. Monte Carlo simulations were performed to model configurational SRO on a fixed lattice, which by itself is shown to have a minimal influence on the PDF. Instead, we find that it is the bond length relaxations within environments created by SRO which controls the details of the PDF, thereby highlighting the subtle but important coupling between configurational and displacive SRO in disordered materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Kinetics of short-range order formation in GeSn alloy: MBE vs CVD

Recently, short-range order (SRO) has attracted significant attention, challenging the conventional view of the atomic positions in alloys being random. Furthermore, the presence of SRO has been predicted to have profound effects on the electronic and topological properties of group-IV alloys, offering a different direction in designing group-IV materials for photoelectronic and quantum devices. However, due to the limited understanding of the formation mechanisms, developing effective methods to manipulate SRO in epitaxy is still challenging. To address this, we propose a mechanism for the GeSn alloy, revealing that surface diffusion plays a key role in SRO formation. Building on this mechanism, we show that the distinct surface conditions in MBE and CVD lead to the formation of SRO with enhanced Sn–Sn pairing in MBE-grown samples, while CVD-grown samples remain random alloys. Furthermore, our findings provide an initial understanding of the kinetic process of SRO formation, providing guidance for the design of experiments to manipulate SRO.

Alloys↗
DOE OSTI2023

Role of local atomic short-range order distribution in alloys: Why it matters in Si-Ge-Sn alloys

Short-range order (SRO) in alloys refers to deviations from a perfectly random distribution of atoms in lattice sites within a short distance. Conventionally, the degree of the deviations has been quantified using an average SRO parameter, but such a coarse-grained description does not reflect how the deviations occur at a finer level. Here we show the distribution of the local atomic SRO parameter, which describes the occurring frequency of a local structural motif, carries the crucial information for both structures and properties in Si-Ge-Sn alloy system. Here this is demonstrated through the fact that distinct SRO structures can exhibit the same average SRO parameter but very different distributions and disparate electronic structures. By deliberately creating special structures that explicitly match the structural information at different levels, we show the distribution of local atomic SRO parameters contain critical structural features that are missing in the average SRO parameter but can substantially contribute to material’s properties. Our finding thus calls for the need for considering the finer structural details to effectively describe alloys’ structures and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

First-principles and cluster expansion study of the effect of magnetism on short-range order in Fe–Ni–Cr austenitic stainless steels

Short-range order (SRO), the regular and predictable arrangement of atoms over short distances, alters the mechanical properties of technologically relevant structural materials such as medium/high entropy alloys and austenitic stainless steels. In this study, we present a generalized spin cluster expansion (CE) model and show that magnetism is a primary factor influencing the level of SRO present in austenitic Fe-Ni-Cr alloys. The spin CE consists of a chemical cluster expansion combined with an Ising model for Fe-Ni-Cr austenitic alloys. It explicitly accounts for local magnetic exchange interactions, thereby capturing the effects of finite temperature magnetism on SRO. Model parameters are obtained by fitting to a first-principles data set comprising both chemically and magnetically diverse FCC configurations. The magnitude of the magnetic exchange interactions are found to be comparable to the chemical interactions. Compared to a conventional implicit magnetism CE built from only magnetic ground state configurations, the spin CE shows improved performance on several experimental benchmarks over a broad spectrum of compositions, particularly at higher temperatures due to the explicit treatment of magnetic disorder. We find that SRO is strongly influenced by alloy Cr content, since Cr atoms prefer to align antiferromagnetically with nearest neighbors but become magnetically frustrated with increasing Cr concentration. Using the spin CE, we predict that increasing the Cr concentration in typical austenitic stainless steels promotes the formation of SRO and increases order-disorder transition temperatures. Furthermore, this study underscores the significance of considering magnetic interactions explicitly when exploring the thermodynamic properties of complex transition metal alloys. It also highlights guidelines for customizing SRO through adjustments of alloy composition.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Revealing local order via high energy EELS

Short range order (SRO) is critical in determining the performance of many important engineering materials. However, accurate characterization of SRO with high spatial resolution – which is needed for the study of individual nanoparticles and at material defects and interfaces – is often experimentally inaccessible. Here, we locally quantify SRO via scanning transmission electron microscopy with extended energy loss fine structure analysis. Specifically, we use novel instrumentation to perform electron energy loss spectroscopy out to 12 keV, accessing energies which are conventionally only possible using a synchrotron. Our data is of sufficient energy resolution and signal-to-noise ratio to perform quantitative extended fine structure analysis, which allows determination of local coordination environments. To showcase this technique, we investigate a multicomponent metallic glass nanolaminate and locally quantify the SRO with <10 nm spatial resolution; this measurement would have been impossible with conventional synchrotron or electron microscopy methods. Finally, we discuss the nature of SRO within the metallic glass phase, as well as the wider applicability of our approach for determining processing–SRO–property relationships in complex materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ubiquitous short-range order in multi-principal element alloys

Recent research in multi-principal element alloys (MPEAs) has increasingly focused on the role of short-range order (SRO) on material performance. However, the mechanisms of SRO formation and its precise control remain elusive, limiting the progress of SRO engineering. Here, leveraging advanced additive manufacturing techniques that produce samples with a wide range of cooling rates (up to 10 7 K s –1 ) and an enhanced semi-quantitative electron microscopy method, we characterize SRO in three CoCrNi-based face-centered-cubic (FCC) MPEAs. Surprisingly, irrespective of the processing and thermal treatment history, all samples exhibit similar levels of SRO. Atomistic simulations reveal that during solidification, prevalent local chemical order arises in the liquid-solid interface (solidification front) even under the extreme cooling rate of 10 11 K s –1 . This phenomenon stems from the swift atomic diffusion in the supercooled liquid, which matches or even surpasses the rate of solidification. Therefore, SRO is an inherent characteristic of most FCC MPEAs, insensitive to variations in cooling rates and even annealing treatments typically available in experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manipulating topological Hall-like signatures by interface engineering in epitaxial ruthenate/manganite heterostructures

Topologically protected non-trivial spin textures (e.g. skyrmions) give rise to a novel phenomenon called the topological Hall effect (THE) and have promising implications in future energy-efficient nanoelectronic and spintronic devices. Here, we have studied the Hall effect in SrRuO 3 /La 0.42 Ca 0.58 MnO 3 (SRO/LCMO) bilayers. Our investigation suggests that pure SRO has hard and soft magnetic characteristics but the anomalous Hall effect (AHE) in SRO is governed by the high coercivity phase. Here, we have shown that the proximity effect of a soft magnetic LCMO on SRO plays a critical role in interfacial magnetic coupling and transport properties in SRO. Upon reducing the SRO thickness in the bilayer, the proximity effect becomes the dominant feature, enhancing the magnitude and temperature range of THE-like signatures. The THE-like features in bilayers can be explained by a diffusive Berry phase transition model in the presence of an emergent magnetic state due to interface coupling. This work provides an alternative understanding of THE-like signatures and their manipulation in SRO-based heterostructures, bilayers and superlattices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2023

Structure and dynamics of $\mathrm{Fe_{90}}$$\mathrm{Si_3}$$\mathrm{O_7}$ liquids close to Earth's liquid core conditions

Using an artificial neural-network machine learning interatomic potential, we have performed molecular dynamics simulations to study the structure and dynamics of $\mathrm{Fe_{90}}$$\mathrm{Si_3}$$\mathrm{O_7}$ liquid close to the Earth's liquid core conditions. Here, the simulation results reveal that the short-range structural order (SRO) in the $\mathrm{Fe_{90}}$$\mathrm{Si_3}$$\mathrm{O_7}$ liquid is very strong. About 80% of the atoms are arranged in crystallinelike SRO motifs. In particular, ~ $70$% of Fe-centered clusters can be classified as either hexagonal-close-packed-like or icosahedrallike SRO motifs. The SRO clusters centered on Fe, Si, or O atoms are strongly intermixed and homogenously distributed throughout the liquid. The atomic structure of the liquid and the fractions of dominant SRO clusters are not sensitive to pressure/temperature used in the simulations except that the SRO of the O-centered clusters is enhanced close to inner core pressures. The O-diffusion coefficient is about two to three times larger than the Fe and Si ions and increases more rapidly in the deeper core regions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Reversal of Anomalous Hall Effect and Octahedral Tilting in SrRuO 3 Thin Films via Hydrogen Spillover

Abstract The perovskite SrRuO 3 (SRO) is a strongly correlated oxide whose physical and structural properties are strongly intertwined. Notably, SRO is an itinerant ferromagnet that exhibits a large anomalous Hall effect (AHE) whose sign can be readily modified. Here, a hydrogen spillover method is used to tailor the properties of SRO thin films via hydrogen incorporation. It is found that the magnetization and Curie temperature of the films are strongly reduced and, at the same time, the structure evolves from an orthorhombic to a tetragonal phase as the hydrogen content is increased up to ≈0.9 H per SRO formula unit. The structural phase transition is shown, via in situ crystal truncation rod measurements, to be related to tilting of the RuO 6 octahedral units. The significant changes observed in magnetization are shown, via density functional theory (DFT), to be a consequence of shifts in the Fermi level. The reported findings provide new insights into the physical properties of SRO via tailoring its lattice symmetry and emergent physical phenomena via the hydrogen spillover technique.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Density functional study of atomic arrangements in CrMnFeCoNi high-entropy alloy and their impact on vacancy formation energy and segregation

Here, using the density functional theory-coupled Monte Carlo approach, we explored the chemical short-range order (SRO) and element segregation in equimolar CrMnFeCoNi alloy. We found that state-of-the-art approximation of random element distribution is only applicable at > 1100 K close to the melting temperature, while the Cr-Cr repulsion driving the system stabilization and accompanying the formation of cubic Cr sublattice, and mild Ni-Ni attraction are the most prominent pair interactions at lower temperatures. Chemical potential and vacancy formation energy calculations indicate that Cr is most sensitive to the local chemical environment, making Cr atoms most stabilized when the preferred SRO is introduced. While the vacancy formation is predicted equally probable among five constituting elements in the random solid solution, Cr and Ni atoms show the lowest vacancy formation energies in the structure with SRO. Furthermore, distinct element segregation was predicted in the vicinity of planar defects, including symmetric tilt grain boundary and stacking fault, which we correlated to the site- and chemistry-dependent atomic volume and bond lengths. It suggests that the local mechanical strain and bond energy induce the SRO development and element segregation: Namely, the system takes advantage of segregation of Ni atoms having large atomic volume or Cr-Cr pairs having elongated bond lengths to fill in the excess volume at defects that relaxes the mechanical strain field and optimizes bond energy distribution. The correlation between the SRO and properties of CrMnFeCoNi alloy needs further investigations, which is expected to greatly help understand and control the properties of high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Detection of the Chiral Spin Structure in Ferromagnetic SrRuO 3 Thin Film

SrRuO3 (SRO) thin films and their heterostructure have brought much attention because of the recently demonstrated fascinating properties, such as topological Hall effect and skyrmions. Critical to the understanding of those SRO properties is the study of the spin configuration. Here, we conduct resonant soft x-ray scattering (RSXS) at the oxygen K-edge to investigate the spin configuration of a 4 unit-cell SRO film that was grown epitaxially on a single crystal SrTiO 3 . The RSXS signal under a magnetic field (~0.4 Tesla) clearly shows a magnetic dichroism pattern around the specular reflection. Model calculations on the RSXS signal demonstrate that the magnetic dichroism pattern originates from a Néel-type chiral spin structure in this SRO thin film. We believe that the observed spin structure of the SRO system is a critical piece of information for understanding its intriguing magnetic and transport properties.

36 MATERIALS SCIENCE↗