Search NASA⌕ Search

SEARCH · Search NASA

Results for “304L stainless steel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Shock Hugoniot of forged and additively manufactured 304L stainless steel

The purpose of this research was to measure the equation of state for additively manufactured (AM) and forged 304L stainless steel. An understanding of the dynamic behavior of AM metals is integral to their timely adoption into industrial and governmental applications. The Hugoniot of the AM 304L was compared to that of the forged 304L. This comparison enabled us to determine the sensitivity of the equation of state to processing parameters and the resulting microstructure. Our results show that there is a measurable difference in the Hugoniot between the AM 304L and forged 304L. The shock wave velocities for the AM 304L were found to be slower than those for the forged 304L at similar particle speeds perhaps because of the presence of porosity in the AM 304L. While our measurements of density showed no distinct trend toward a measurable decrease in density in the AM 304L, there was a fair amount of scatter in these results.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strength models for stainless steel 304L alloys

This report provides nominal, weak and strong calibrations of Preston- Tonks-Wallace (PTW) plasticity model [1] parameters for stainless steel 304L alloys. The data sets shown indicate that for these alloys, the material’s prove- nance plays an important role in accurate characterization. First we provide a parameter set fit to compression-tested annealed samples, both quasistatic (QS) and split Hopkinson pressure bar (SHPB), from the MST-8 group at LANL within the last year. Then we compare simulations using the FLAG hydrocode [2], with this and other parameter sets, to data from a Taylor cylinder impact test performed within the same group around 2013.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comprehensive Characterization of Helium-Induced Degradation of the Friction Stir Weld on Neutron-Irradiated 304L Stainless Steel

The report describes new experimental results on the mechanical performance of the friction stir welds made on neutron-irradiated 304L stainless steel with helium. The report focuses on helium-related issues (e.g., the helium-induced degradation in the welded joint), aiming at the need to repair irradiated components of nuclear power plants. The friction stir welds analyzed here were previously produced at the US Department of Energy’s Oak Ridge National Laboratory, and initial characterization work was performed, mostly addressing the microstructure and if macroscopic cracks and helium bubbles present. The present work attempts to perform a more comprehensive study to assess mechanical performance (i.e., microhardness distribution, tensile properties, tensile deformation behaviors, and fractography analysis).

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evaluation of Applied Stress on Atmospheric Corrosion and Pitting Characteristics in 304L Stainless Steel

For this study, the effects of applied stress, ranging from tensile to compressive, on the atmospheric pitting corrosion behavior of 304L stainless steel (SS304L) were analyzed through accelerated atmospheric laboratory exposures and microelectrochemical cell analysis. After exposing the lateral surface of a SS304L four-point bend specimen to artificial seawater at 50°C and 35% relative humidity for 50 d, pitting characteristics were determined using optical profilometry and scanning electron microscopy. The SS304L microstructure was analyzed using electron backscatter diffraction. Additionally, localized electrochemical measurements were performed on a similar, unexposed, SS304L four-point bend bar to determine the effects of applied stress on corrosion susceptibility. Under the applied loads and the environment tested, the observed pitting characteristics showed no correlation with the applied stress (from 250 MPa to -250 MPa). Pitting depth, surface area, roundness, and distribution were found to be independent of location on the sample or applied stress. The lack of correlation between pitting statistics and applied stress was more likely due to the aggressive exposure environment, with a sea salt loading of 4 g/m 2 chloride. The pitting characteristics observed were instead governed by the available cathode current and salt distribution, which are a function of sea salt loading, as well as pre-existing underlying microstructure. In microelectrochemical cell experiments performed in Cl - environments comparable to the atmospheric exposure and in environments containing orders of magnitude lower Cl - concentrations, effects of the applied stress on corrosion susceptibility were only apparent in open-circuit potential in low Cl - concentration solutions. Cl - concentration governed the current density and transpassive dissolution potential.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Determination of the Solid-State Resistance-Weldability of Additively Manufactured 304L Stainless Steel

• A scoping study was undertaken at Savannah River National Laboratory (SRNL) to determine the solidstate resistance-weldability of additively manufactured 304L stainless steel. • Additive manufacturing of pressure-containing boundaries is of interest to numerous industries. • The approach investigated in this study was a low energy, solid state spot weld (pinch weld). • This general approach has been routinely used for conventionally prepared tubing and is now being expanded to additively manufactured components. • This work aimed to understand the impact of AM on the bond quality and weld geometry of pinch welds.

Rogers, Jeremy K. [Savannah River National Laborat↗
DOE OSTI2023

In Situ X-ray Diffraction Investigation of Hydrogen Effects on Deformation-Induced Phase Transformation in Forged and Additively Manufactured 304L Stainless Steels

Here, this study utilized high energy synchrotron x-ray diffraction to probe microstructural evolution during uniaxial deformation of conventionally manufactured and additively manufactured (AM) 304L stainless steel with and without internal hydrogen. The objective of this effort is to highlight the effect of hydrogen on deformation-induced martensite phase transformations in austenitic stainless steels. Solute hydrogen depresses the required applied strain to initiate austenite transformation to ε-martensite and α'-martensite in both forged and AM stainless steel. Similarly, the total fraction of transformation product is larger when the microstructure is saturated with hydrogen. Deformation induced phase transformations also lead to a variation in strain partitioning behavior, which is linked to the chemical composition and stacking fault energy of the starting and hydrogen-charged materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Response of 304L stainless steel and 6061-T651 aluminum alloy at -40 °C

The objective of this work is to extend the thermal-mechanical, elastic-plastic calibrations for 304L stainless steel [1] and and 6061-T651 aluminum alloy [2] to the regime between room temperature and -40 °C. The basis to extend the calibration consisted of new uniaxial tension tests conducted at -40 °C using the same plate material stocks, circular cylindrical specimen geometries and testing apparatus as previously, followed by attempts to fit power-law hardening functions to replicate the response observed in the specimens and then extend the yield, hardening constant, hardening exponent and rate constant functions in the calibrations to cover the new temperature regime.

36 MATERIALS SCIENCE↗
DOE OSTI2025

In Situ Measurement of Stress Corrosion Crack Tip Properties During Environmentally Induced Cracking in Stainless Steel 304L

The influence of the external cathodic area, stress intensity, and electrochemical polarization level on the resultant crack growth rate and crack tip pH and potential was studied for stainless steel 304L in a sodium chloride environment. Before testing, the validity of in situ crack tip property measurements using microprobes and drilled holes was supported through modeling efforts and confirmed with experimental observations. Here, it was found that increasing the R-ratio during corrosion fatigue increased the crack growth rate and decreased the measured crack tip pH of the 304L sample. Decreasing the electrochemical potential (i.e., cathodic polarization) of the bulk sample increased the crack tip pH and stopped measured crack extension under constant K conditions. Conversely, increasing the potential of the bulk sample decreased the crack tip pH and induced cracking under constant K conditions. Decreasing the cathodic area external to the crack increased the measured pH at the crack tip and decreased the crack growth rate under fatigue conditions. For the given configuration, environment, and alloy studied, fatigue crack growth is not sustained by cathodic reactions solely occurring in the crack wake and notch. These results have implications for the ability to predict atmospheric crack growth rates from laboratory, full immersion experiments.

corrosion fatigue↗
DOE OSTI2022

Effect of processing parameters and build orientation on microstructure and performance of AISI stainless steel 304L made with selective laser melting under different strain rates

Selective laser melting (SLM) process brings diverse potentials on geometry flexibility; therefore, it is more and more widespread to be employed in fabrication metal alloys served for industries. Nonetheless, a material characterization study is desired to carry on for better understanding the correlation among process, structure, microstructure, and performance. In the current study, the SLM fabricated AISI stainless steel 304L was fabricated with different process parameters and built orientations (horizontal, inclined, and vertical. The tensile behavior was evaluated under different strain rates (0.0001 /s, 0.001 /s, 0.01 /s, and 0.1 /s) and compared to the commercial cold-rolled and annealed counterpart. Grain structures, tensile strength, elongation-to-failure, strain rate sensitivity, work hardening, and fractographic analysis were evaluated in terms of the effect of energy density, build orientation, and strain rate. The output indicates the tensile strength increases with increasing strain rates. On the contrary, the elongation-to-failure shows a decreasing trend with strain rates. Tensile properties of specimens built in the horizontal and inclined orientations are more sensitive to strain rates due to the smaller dimension of grain structures. Tensile anisotropy depends on the energy input, where a high energy density could yield a strong build orientation-dependent anisotropy. Hall-Petch relationship is validated to explain the mechanical anisotropy in different built orientations for SLM alloys. The strain hardening exponent and work hardening rate are demonstrated to be positively correlated, and they increase with smaller grain sizes. The fine dimple features indicate the ductile fracture mode regardless of strain rates. The size of the ductile dimples seems to depend on the strain rates and build orientations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Analysis of the MST-16 crimp process on cold 304L stainless steel

The purpose of this report is to assess the quality of the MST-16 crimp process through a series of cold experiments and metallographic analyses. Common practice in MST-16 uses a mechanical crimp on 304L stainless steel tubes to prevent radioactive contamination from escaping the tube interior for a variety of experiments. The crimped tubes must pass a leak check to demonstrate their radiological safety. Cold (i.e. non-radioactive samples) 304L tube samples were tested using two different approved crimping devices to assess the quality of the crimps. Each crimp was leak checked, followed by destructive metallographic analysis to determine the quality of both the crimp equipment and procedures used by MST-16 personnel.

42 ENGINEERING↗
DOE OSTI2023

Spall strength of additively repaired 304L stainless steel

Additive manufacturing has the potential to repair damaged parts, but the performance of additive materials under high strain rate loading is still uncertain—especially with the added complexity of an interface with an existing wrought material. In this work, 304L stainless steel samples were intentionally damaged and then repaired with wire-fed laser additive manufacturing. The samples were subjected to shock loading to generate incipient spall. Velocimetry and post-mortem metallography results show that when the additive repair process parameters are optimized to reduce porosity and match the equation of state of the original material, the influence of the repair region on the shock propagation is negligible. In conclusion, the free-surface velocity profile and internal damage morphology of the repaired sample are shown to be practically identical to the pristine material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Towards Multilayered Coatings of 304L Stainless Steels Using Friction Surfacing

Abstract The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.

Engineering↗
DOE OSTI2025

DETERMINATION OF THE SOLID-STATE RESISTANCE-WELDABILITY OF ADDITIVELY MANUFACTURED 304L STAINLESS STEEL

Additive manufacturing of pressure-containing boundaries is of interest to numerous industries, so a project was initiated to develop several different methods to join and weld additively manufactured materials. The approach investigated in this study was a low energy, solid state spot weld. This general approach has been routinely used for conventionally prepared tubing and is now being expanded to additively manufactured components. Additively manufactured 304L stainless steel sheets, semi-tubes, and tubes were resistance spot welded and compared to comparable welds in conventionally manufactured tubing. Radiographic computed tomography and metallography were used to evaluate the suitability of the welds using three criteria: weld closure length, thickness, and width. All additively manufactured test welds closely matched the conventional tubing for these criteria

additive manufacturing↗
DOE OSTI2020

Fatigue behavior and modeling for additive manufactured 304L stainless steel: The effect of surface roughness

The fatigue strength of additively manufactured metallic parts in their as-built surface condition is mainly dominated by the surface roughness. Post-processing is often inevitable to reduce surface roughness effects even though post-processing diminishes the main advantage of additive manufacturing, which is net-shaped direct-to-service production. This work investigates the underlying mechanisms responsible for fatigue failure of additively manufactured 304L stainless steel parts in as-built and machined/polished surface conditions. Both strain- and force-controlled, fully reversed fatigue tests were conducted to gain a comprehensive understanding of surface roughness effects on fatigue behavior. The sensitivity to surface roughness is shown to be dependent on the control mode, with stress-based fatigue tests showing greater sensitivity than strain-based fatigue tests. Moreover, the fatigue life estimation for as-built specimens was performed based on surface roughness parameters as well as the fatigue properties of the specimens in machined/polished surface condition of the material without using any fatigue data of specimens in as-built surface condition. Accordingly, the effect of surface roughness on the fatigue behavior could be estimated reasonably well in both strain-life and stress-life approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigation of Mechanical Properties of Parts Fabricated with Gas- and Water-Atomized 304L Stainless Steel Powder in the Laser Powder Bed Fusion Process

In this report the use of gas-atomized powder as the feedstock material for the Laser Powder Bed Fusion (L-PBF) process is common in the Additive Manufacturing (AM) community. Although gas-atomization produces powder with high sphericity, its relatively expensive production cost is a downside for application in AM processes. Water atomization of powder may overcome this limitation due to its low cost relative to the gas-atomization process. In this work, gas- and water-atomized 304L stainless steel powders were morphologically characterized through Scanning Electron Microscopy (SEM). The water-atomized powder had a wider particle size distribution and exhibited less sphericity. Measuring powder flowability using the Revolution Powder Analyzer (RPA) indicated that the water-atomized powder had less flowablility than the gas-atomized powder. Through examining the mechanical properties of L-PBF fabricated parts using tensile tests, the gas-atomized powder had significantly higher yield tensile strength and elongation than the water-atomized powder, however, their ultimate tensile strengths were not significantly different.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Digital image correlation and infrared thermography data for seven unique geometries of 304L stainless steel

Material Testing 2.0 (MT2.0) is a paradigm that advocates for the use of rich, full-field data, such as from digital image correlation and infrared thermography, for material identification. By employing heterogeneous, multi-axial data in conjunction with sophisticated inverse calibration techniques such as finite element model updating and the virtual fields method, MT2.0 aims to reduce the number of specimens needed for material identification and to increase confidence in the calibration results. To support continued development, improvement, and validation of such inverse methods—specifically for rate-dependent, temperature-dependent, and anisotropic metal plasticity models—we provide here a thorough experimental data set for 304L stainless steel sheet metal. The data set includes full-field displacement, strain, and temperature data for seven unique specimen geometries tested at different strain rates and in different material orientations. Commensurate extensometer strain data from tensile dog bones is provided as well for comparison. We believe this complete data set will be a valuable contribution to the experimental and computational mechanics communities, supporting continued advances in material identification methods.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 304L Stainless Steel Alloy

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The material of interest here is 304L stainless steel, and the objective of this work is to calibrate thermal-mechanical models: one for the constitutive behavior and another for failure. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of the models. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s. It also included notched tension and shear-dominated compression hat tests specifically designed to calibrate the failure model. All test specimens were extracted from a single piece of plate to maintain consistency. The constitutive model adopted was a modular $J_2$ plasticity model with isotropic hardening that included rate and temperature dependence. A criterion for failure initiation based on a critical value of equivalent plastic strain fitted the failure data appropriately and was adopted. Possible ranges of the values of the parameters of the models were determined partially on historical data from calibrations of the same alloy from other lots and are given here. The calibration of the parameters of the models were based on finite element simulations of the various material tests using relatively ne meshes and hexahedral elements. When using the model in structural finite element calculations, however, element formulations and sizes different from those in the calibration are likely to be used. A brief investigation demonstrated that the failure initiation predictions can be particularly sensitive to the element selection and provided an initial guide to compensate for the effect of element size in a specific example.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Correlation of SWIR imaging with LPBF 304L stainless steel part properties

In the Laser Powder Bed Fusion (LPBF) process, the local thermal history can vary significantly over a part as the heat transfer characteristics and the laser scan path are geometry dependent. The variations introduce the potential for defects that lead to part failure, some of which are difficult to identify non-destructively with common ex-situ evaluation techniques. These defects include significant microstructural and mechanical property differences in the part interiors. In this paper, thermal features are extracted from in-situ Short-Wave Infrared (SWIR) imaging measurements to compile voxel based part representations and understand how the complexities in the thermal history affect part performance. The deviations in thermal features due to different laser processing parameters and complex scan pathing are explored. Empirical correlations are developed to map thermal features with the engineering properties (bulk yield strength, area percentage porosity, and local state) of 304L stainless steel parts manufactured by LPBF. Processing modes (insufficient melting and keyholing) are determined by mapping part property measurements with multiple thermal features. Generating the relationships between thermographic measurements and resulting SLM part properties lays the foundation for in-situ part qualification.

36 MATERIALS SCIENCE↗