Search NASA⌕ Search

SEARCH · Search NASA

Results for “6 degrees of freedom”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Sleuthing the MSL EDL Performance from an X Band Carrier Perspective

During the Entry, Descent, and Landing (EDL) of NASA's Mars Science Laboratory (MSL), or Curiosity, rover to Gale Crater on Mars on August 6, 2012 UTC, the rover transmitted an X-band signal composed of carrier and tone frequencies and a UHF signal modulated with an 8kbps data stream. During EDL, the spacecraft's orientation is determined by its guidance and mechanical subsystems to ensure that the vehicle land safely at its destination. Although orientation to maximize telecom performance is not possible, antennas are especially designed and mounted to provide the best possible line of sight to Earth and to the Mars orbiters supporting MSL's landing. The tones and data transmitted over these links are selected carefully to reflect the most essential parameters of the vehicle's state and the performance of the EDL subsystems for post-EDL reconstruction should no further data transmission from the vehicle be possible. This paper addresses the configuration of the X band receive system used at NASA / JPL's Deep Space Network (DSN) to capture the signal spectrum of MSL's X band carrier and tone signal, examines the MSL vehicle state information obtained from the X band carrier signal only and contrasts the Doppler-derived information against the post-EDL known vehicle state. The paper begins with a description of the MSL EDL sequence of events and discusses the impact of the EDL maneuvers such as guided entry, parachute deploy, and powered descent on the frequency observables expected at the DSN. The range of Doppler dynamics possible is derived from extensive 6 Degrees-Of-Freedom (6 DOF) vehicle state calculations performed by MSL's EDL simulation team. The configuration of the DSN's receive system, using the Radio Science Receivers (RSR) to perform open-loop recording for both for nominal and off-nominal EDL scenarios, is detailed. Expected signal carrier power-to-noise levels during EDL are shown and their impact on signal detection is considered. Particular attention is given to the selection of the appropriate RSR processing bandwidths and to its configuration for real-time signal detection. The X-band carrier frequency obtained through post-processing of the open-loop recorded spectrum is given. Detection of spacecraft status and completion of key vehicle events through their Doppler signature is discussed and illustrated. This Doppler-derived information is compared against the very accurate vehicle data obtained post-EDL via MSL's UHF radio subsystem. The paper concludes with a discussion on the advantages and disadvantages of transmitting the X-band carrier and tone signal in the general context of EDL communications and lessons learned for future missions with EDL sequences are given

Mars Science Laboratory (MSL)↗
NASA NTRSDate not supplied

Demonstration of Linear Covariance Analysis Techniques to Evaluate Entry Descent and Landing Guidance Algorithms, Vehicle Configurations, Analysis Techniques, and Trajectory Profiles

Linear covariance analysis techniques have been previously developed to analyze closed-loop entry, descent, and landing (EDL) scenarios and the initial validation efforts are under-way confirming the generated GN&C system performance results. Given both the theoretical foundation and previous conceptual demonstration, this work begins to flex the potential of linear covariance analysis for atmospheric flight and highlight its versatility and reliability by evaluating multiple entry guidance algorithms, vehicle configurations, trajectory profiles, environment conditions, and analysis techniques for a variety of trade studies. To demonstrate the benefit linear covariance analysis can provide in producing rapid yet accurate performance data, two entry profiles are adopted including the NASA Mars Science Laboratory (MSL) and Exploration Flight Test-1 (EFT-1) while utilizing two different guidance algorithms, the Apollo Final Phase (AFP) and the Fully Numeric Predictor-Corrector Entry Guidance (FNPEG) with different navigation sensor suites in a 6 degree-of-freedom (6-DOF) simulation environment. Results are shown using both linear covariance and Monte Carlo analysis techniques to high-light the consistency between the two methodologies and continue the validation maturation of linear covariance analysis for entry, descent, and landing.

EDL↗
NASA NTRSDate not supplied

Performance Analysis of A Dual Quaternion Guidance Algorithm Applicable During Lunar Approach With A Hazard Avoidance Maneuver

There is currently a need for advanced guidance and targeting algorithms that can provide real-time trajectories in the presence of state and vehicle constraints during powered descent. The Safe & Precise Landing Integrated Capabilities Evolution (SPLICE) program aims to mature Hazard Detection (HD) technology along with advanced navigation and guidance algorithms. This paper will report the overall performance of the SPLICE Dual Quaternion Guidance (DQG) algorithm which is a 6-Degree-of-Freedom (6-DOF) convex optimization-based guidance algorithm that can enforce multiple vehicle and state constraints required for Hazard Detection Lidar (HDL) scans during the approach phase. DQG was tested in a closed-loop lunar descent simulation with realistic HDL sensing constraints in a Monte Carlo assessment of 1000 dispersed runs.

Guidance↗
NASA NTRS1977

The LEMMA concept - A new manipulator

The LEMMA is a proposed conceptual design of a remote teleoperator manipulator arm with 6 degrees of freedom, exclusive of the end-effector. The bevel gear arrangement in 4 of the 6 degrees of freedom, together with the concentric-tubular arm configuration, requires a unique and novel drive mechanism. This differential drive assembly, housed in the shoulder, is a self-compensating device and simplifies the matrix solution for the resolved motion rate control system needed to guide the arm in its performances. The article will describe the need for the 6 degrees of freedom as established by the work envelope, the functioning of the differential shoulder drive, the arm and joint configuration, and the anticipated degree of accuracy.

Kersten, L.↗
NASA NTRSDate not supplied

Developing Urban Air Mobility Vehicle Models to Support Air Traffic Management Concept Development

To support Urban Air Mobility (UAM) research efforts at NASA, the Airspace Target Generator (ATG) software used in the FutureFlight Central (FFC) air traffic control tower simulator is undergoing updates to support physics-based UAM vehicle models. A process was developed to integrate UAM vertical takeoff and landing (VTOL) aircraft into the fixed-wing ATG modeling environment without significant change to the underlying equations of motion and vehicle model database. The VTOL aircraft models were converted from a six degrees-of-freedom (6-DOF) representation into a four degrees-of-freedom (4-DOF) representation for integration within ATG. Three vehicle designs from the NASA Revolutionary Vertical-Lift Technologies (RVLT) project were selected: a lift-plus-cruise (LPC) aircraft model and quadrotor, electric-powered (QEP) 1-seater and 6-seater models. With the LPC model comprised of a nonlinear force and moment build-up, and the QEP models comprised of linearized stability derivatives, two separate processes were developed to convert the lift, drag, and propulsion characteristics of each model into the ATG model database. Key aircraft performance characteristics including climb, cruise, and descent performance were preserved during the conversion process. Because ATG simulates fixed-wing aircraft through ground taxi and takeoff to approach and landing, acceleration command algorithms were developed to model the vertical takeoff and vertical landing phase of UAM operations. A strategy was then developed to transition the aircraft model to- and from- the new control mode.

urban air mobility↗
NASA NTRS1990

A new six-degree-of-freedom force-reflecting hand controller for space telerobotics

A new 6 degree of freedom universal Force Reflecting Hand Controller (FRHC) was designed for use as the man-machine interface in teleoperated and telerobotic flight systems. The features of this new design include highly intuitive operation, excellent kinesthetic feedback, high fidelity force/torque feedback, a kinematically simple structure, mechanically decoupled motion in all 6 DOF, good back-drivability, and zero backlash. In addition, the new design has a much larger work envelope, smaller stowage volume, greater stiffness and responsiveness, and better overlap of the human operator's range of motion than do previous designs. The utility and basic operation of a new, flight prototype FRHC called the Model X is briefly discussed. The design heritage, general design goals, and design implementation of this advanced new generation of FRHCs are presented, followed by a discussion of basic features and the results of initial testing.

Mcaffee, Douglas↗
NASA NTRS2008

Compact 6-DOF Stage for Optical Adjustments

The figure depicts selected aspects of a six-degree-of-freedom (6-DOF) stage for mechanical adjustment of an optical component. The six degrees of freedom are translations along the Cartesian axes (x, y, and z) and rotations about these axes (theta x, theta y, and theta z, respectively). Relative to prior such stages, this stage offers advantages of compactness, stability, and robustness, plus other advantages as described below. The stage was designed specifically as part of a laser velocimeter and altimeter in which light reflected by a distant object is collected by a Cassegrainian telescope and focused into a single-mode, polarization-maintaining optical fiber. The stage is used to position and orient the input end of the optical fiber with respect to the focal point of the telescope. Stages like this one can also be adapted for use in positioning and orienting other optical components, including lenses, prisms, apertures, and photodetectors.

Shafaat, Syed↗
NASA NTRS1991

Six degree of freedom simulation system for evaluating automated rendezvous and docking spacecraft

Future logistics supply and servicing vehicles such as cargo transfer vehicles (CTV) must have full 6 degree of freedom (6DOF) capability in order to perform requisite rendezvous, proximity operations, and capture operations. The design and performance issues encountered when developing a 6DOF maneuvering spacecraft are very complex with subtle interactions which are not immediately obvious or easily anticipated. In order to deal with these complexities and develop robust maneuvering spacecraft designs, a simulation system and associated family of tools are used at TRW for generating and validating spacecraft performance requirements and guidance algorithms. An overview of the simulator and tools is provided. These are used by TRW for autonomous rendezvous and docking research projects including CTV studies.

Rourke, Kenneth H.↗
NASA NTRS1987

The design of a nine-string six-degree-of-freedom force-feedback joystick for telemanipulation

An overview is given of the design and controlling equations for a 6-degree-of-freedom force-feedback joystick for telemanipulation. The joystick has a parallel mechanical structure which allows all of its actuators to be fixed to a non-moving base. The low-inertia design is expected to provide an accurate force-feedback signal to the joystick operator without the need for closed-loop momentum compensation. The analysis describes the joystick's inputs and outputs in generalized Cartesian space, so the joystick can potentially be used as an interface for any 6-degree-of-freedom device.

Agronin, M. L.↗
NASA NTRSDate not supplied

Free-Flight CFD Simulations and Dynamic StabilityAnalysis of the Orion Crew Module

Dynamic stability analysis of the Multi-Purpose Crew Vehicle (MPCV) is performed us-ing the US3D flow solver and a plugin library to solve rigid-body dynamics, Free-Flight CFD(FF-CFD). Previous efforts investigated the free-flight behavior of higher speed, open-backaeroshell shapes. Three primary experimental sources are used to evaluate the predictivecapability of the FF-CFD solver in the low supersonic range (Mach≈1). First, the ballisticrange results obtained at the HFFAF facility at NASA Ames is used to verify the six degree-of-freedom (6-DoF) dynamic capability of the FF-CFD solver. Next, FF-CFD simulationsare preformed using restricted motion and the resultant trajectories are post-processed toobtain pitch damping coefficient as a function of angle-of-attack. The comparison of thepitch damping results obtained with one degree-of-freedom (1-DoF) FF-CFD compare wellwith experimental fits derived from ballistic range data. Finally, the atmospheric flight ca-pability of FF-CFD is compared to data from the Ascent Abort-2 (AA-2) flight experiment.Two simulations were performed using forced and forced-free flight to investigate surfacepressure predictive capability and free-flight aerodynamic performance through a varyingatmosphere at low speed (Mach 0.6-0.2). Surface pressure predicted with FF-CFD agreeswell with experimental trends, with slight over-prediction near the end of the trajectory.The total angle-of-attack for the free-flight portion agrees well with experimental data.

FFCFD↗
NASA NTRS1989

Time and frequency-domain identification and verification of BO-105 dynamic models

Mathematical models for the dynamics of the DLR BO 105 helicopter are extracted from flight test data using two different approaches: frequency-domain and time-domain identification. Both approaches are reviewed. Results from an extensive data consistency analysis are given. Identifications for 6 degrees of freedom (DOF) rigid body models are presented and compared in detail. The extracted models compare favorably and their prediction capability is demonstrated in verification results. Approaches to extend the 6 DOF models are addressed and first results are presented. System identification is broadly defined as the deduction of system characteristics from measured data. It provides the only possibility to extract both non-parametric (e.g., frequency responses) and parametric (e.g., state space matrices) aircraft models from flight test data and therefore gives a reliable characterization of the dynamics of the actually existing aircraft. Main applications of system identification are seen in areas where higher accuracies of the mathematical models are required: Simulation validation, control system design (in particular model-following control system design for in-flight simulation), and handling qualities.

Kaletka, Juergen↗
NASA NTRS1989

Time and frequency-domain identification and verification of BO-105 dynamic models

Mathematical models for the dynamics of the DLR BO 105 helicopter are extracted from flight test data using two different approaches: frequency-domain and time-domain identification. Both approaches are reviewed. Results from an extensive data consistency analysis are given. Identifications for 6 degrees of freedom (DOF) rigid body models are presented and compared in detail. The extracted models compare favorably and their prediction capability is demonstrated in verification results. Approaches to extend the 6 DOF models are addressed and first results are presented. System identification is broadly defined as the deduction of system characteristics from measured data. It provides the only possibility to extract both non-parametric (e.g., frequency responses) and parametric (e.g., state space matrices) aircraft models from flight test data and therefore gives a reliable characterization of the dynamics of the actually existing aircraft. Main applications of system identification are seen in areas where higher accuracies of the mathematical models are required: Simulation validation, control system design (in particular model-following control system design for in-flight simulation), and handling qualities.

Kaletka, Juergen↗
NASA NTRS1991

Analysis and design of a six-degree-of-freedom Stewart platform-based robotic wrist

The kinematic analysis and implementation of a six degree of freedom robotic wrist which is mounted to a general open-kinetic chain manipulator to serve as a restbed for studying precision robotic assembly in space is discussed. The wrist design is based on the Stewart Platform mechanism and consists mainly of two platforms and six linear actuators driven by DC motors. Position feedback is achieved by linear displacement transducers mounted along the actuators and force feedback is obtained by a 6 degree of freedom force sensor mounted between the gripper and the payload platform. The robot wrist inverse kinematics which computes the required actuator lengths corresponding to Cartesian variables has a closed-form solution. The forward kinematics is solved iteratively using the Newton-Ralphson method which simultaneously provides a modified Jacobian Matrix which relates length velocities to Cartesian translational velocities and time rates of change of roll-pitch-yaw angles. Results of computer simulation conducted to evaluate the efficiency of the forward kinematics and Modified Jacobian Matrix are discussed.

Nguyen, Charles C.↗
NASA NTRS2008

Database Driven 6-DOF Trajectory Simulation for Debris Transport Analysis

Debris mitigation and risk assessment have been carried out by NASA and its contractors supporting Space Shuttle Return-To-Flight (RTF). As a part of this assessment, analysis of transport potential for debris that may be liberated from the vehicle or from pad facilities prior to tower clear (Lift-Off Debris) is being performed by MSFC. This class of debris includes plume driven and wind driven sources for which lift as well as drag are critical for the determination of the debris trajectory. As a result, NASA MSFC has a need for a debris transport or trajectory simulation that supports the computation of lift effect in addition to drag without the computational expense of fully coupled CFD with 6-DOF. A database driven 6-DOF simulation that uses aerodynamic force and moment coefficients for the debris shape that are interpolated from a database has been developed to meet this need. The design, implementation, and verification of the database driven six degree of freedom (6-DOF) simulation addition to the Lift-Off Debris Transport Analysis (LODTA) software are discussed in this paper.

West, Jeff↗
NASA NTRS1990

Development of a multipurpose hand controller for JEMRMS

A prototype multipurpose hand controller for the JEMRMS (Japanese Experiment Module Remote Manipulator System) was developed. The hand controller (H/C) is an orthogonal type, with 6 degrees of freedom (DOF) and small size. The orthogonal type H/C is very simple for coordinate transformations and can easily control any type of manipulators. In fact, the JEMRMS is planned to have two manipulators controlled by a common H/C at this stage. The H/C was able to be used as a rate control joystick and a force reflection master arm, using an experimental 6 DOF manipulator. Good maneuverability was confirmed in the verification test. The orthogonal type H/C is suitable for use as a common H/C for the two manipulators of the JEMRMS.

Matsuhira, Nobuto↗
NASA NTRS1996

Simulation of Rotor Blade Element Turbulence

A turbulence model has been developed for blade-element helicopter simulation. This model, called Simulation of Rotor Blade Element Turbulence (SORBET), uses an innovative temporal and geometrical distribution algorithm that preserves the statistical characteristics of the turbulence spectra over the rotor disc, while providing velocity components in real time to each of five blade-element stations along each of four blades. An initial investigation of SORBET has been performed using a piloted, motion-based simulation of the Sikorsky UH60A Black Hawk. Although only the vertical component of stochastic turbulence was used in this investigation, vertical turbulence components induce vehicle responses in all translational and rotational degrees of freedom of the helicopter. The single-degree-of-freedom configuration of SORBET was compared to a conventional full 6-degrees-of-freedom baseline configuration, where translational velocity inputs are superimposed at the vehicle center of gravity, and rotational velocity inputs are created from filters that approximate the immersion rate into the turbulent field. For high-speed flight the vehicle responses were satisfactory for both models. Test pilots could not distinguish differences between the baseline configuration and SORBET. In low-speed flight the baseline configuration received criticism for its high frequency content, whereas the SORBET model elicited favorable pilot opinion. For this helicopter, which has fully articulated blades, results from SORBET show that vehicle responses to turbulent blade-station disturbances are severely attenuated. This is corroborated by in-flight observation of the rotor tip path plane as compared to vehicle responses.

McFarland, R. E.↗
NASA NTRS2019

Modeling and Simulation Techniques for the NASA SLS Service Module Panel Separation Event; from Loosely-Coupled Euler to Fully-Coupled 6-DOF, Time-Accurate, Navier-Stokes Methodologies

An aerodynamic database has been generated for use by the Orion Multi-Purpose Crew Vehicle (MPCV) Program to analyze Service Module (SM) panel jettison from the NASA SLS vehicle. The database is a combination of CFD data for the panel aerodynamic coefficients, and MATLAB code written to query the CFD data. The Cart3D inviscid CFD flow solver was used to generate the panel aerodynamic coefficients for static panel orientations and free stream conditions that can occur during the jettison event. The MATLAB code performs the multivariate interpolation to obtain aerodynamic coefficients. The MATLAB code uses input for SM panel parameters and returns the SM panel aerodynamic force and moment coefficients for use with a Six-Degree-of-Freedom (6-DOF) motion solver to model the jettison event. This paper examines the accuracy of the sequential-static database approach by modeling the panel jettison event with a fully-coupled, time-dependent, viscous, moving-body CFD simulation. The fully-coupled simulation is obtained using the Loci/Chem unstructured Navier-Stokes CFD solver. The results show that the fully-coupled approach agrees well with the loosely-coupled database/6-DOF approach, indicating that unsteady effects are minimal for the panel jettison event. These results suggest that the database/6-DOF approach is sufficient. In addition, this paper presents the development of an uncertainty model for use in Monte Carlo analysis of the panel jettison event. Here viscous CFD simulations are obtained with Loci/Chem and compared to the inviscid CFD forces and moments. An uncertainty model based on model-form error and numerical error is presented.

Hall, Leslie H.↗
DOE OSTI2020

Umbilical Fatigue Analysis for a Wave Energy Converter

Unique umbilical designs for wave energy converters (WECs), including the ability to handle significantly larger motions and loads over long deployments, are often required when conventional marine umbilical designs for offshore oil and gas and offshore wind may not meet the design and cost needs of wave energy technologies. This study details a fatigue analysis of a dynamic power umbilical attached to a two-body floating point absorber WEC system, using the sea states provided for the PacWave testing facilities. The 6 degrees of freedom motion time history for the WEC was simulated, and the motions of the attachment point for the umbilical on the WEC and respective sea states were used to analyze the dynamic motions and fatigue of the connected power umbilical to predict the fatigue life. The results show that the fatigue damage observed is more significant in shallow water, and extensive fatigue damage may occur because of the larger curvature response of the umbilical. The umbilical configurations departing at 90 deg off incoming waves were found to have the highest fatigue life attributed to less extension or compression of the umbilical. However, additional bend stiffener/limiter features may need to be incorporated into the buoyancy section and touchdown regions to minimize curvature-induced fatigue.

50 EE - Wind and Water Power Program - Water (EE-4↗