SEARCH · Search NASA

Results for “AIRFOILS - AERODYNAMIC CENTER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Icing characteristics of a natural-laminar-flow, a medium-speed, and a swept, medium-speed airfoil

Tests were conducted in the Icing Research Tunnel at the NASA Lewis Research Center to determine the icing characteristics of three modern airfoils: a natural-laminar-flow, a medium-speed, and a swept medium-speed airfoil. The tests measured the impingement characteristics and drag degradation for angles-of-attack typifying cruise and climb for cloud conditions typifying the range that might be encountered in flight. The maximum degradation occurred at the cruise angle-of-attack for the long, glaze ice condition for all three airfoils with increases over baseline drag being 486 percent, 510 percent, and 465 percent for the natural-laminar-flow, the medium-speed, and the swept, medium-speed airfoils, respectively. For the climb angle-of-attack, the maximum drag degradation (and total extent of impingement) observed were also for the long, glaze ice condition and were 261 percent, 181 percent, and 331 percent, respectively. The minimum drag degradation (and extent of impingement) occurred for the cruise condition and for the short, rime spray with increases over baseline drag values being 47 percent, 28 percent, 46 percent, respectively.

Bidwell, Colin S.↗

NASA NTRS2002

Intermittent Flow Regimes in a Transonic Fan Airfoil Cascade

A study was conducted in the NASA Glenn Research Center linear cascade on the intermittent flow on the suction surface of an airfoil section from the tip region of a modern low aspect ratio fan blade. Experimental results revealed that, at a large incidence angle, a range of transonic inlet Mach numbers exist where the leading-edge shock-wave pattern was unstable. Flush mounted high frequency response pressure transducers indicated large local jumps in the pressure in the leading edge area, which generates large intermittent loading on the blade leading edge. These measurements suggest that for an inlet Mach number between 0.9 and 1.0 the flow is bi-stable, randomly switching between subsonic and supersonic flows. Hence, it appears that the change in overall flow conditions in the transonic region is based on the frequency of switching between two stable flow states rather than on the continuous increase of the flow velocity. To date, this flow behavior has only been observed in a linear transonic cascade. Further research is necessary to confirm this phenomenon occurs in actual transonic fans and is not the byproduct of an endwall restricted linear cascade.

Lepicovsky, J.↗

NASA NTRS1973

The construction and operation of a water tunnel in application to flow visualization studies of an oscillating airfoil

The water tunnel which was constructed at the NASA Ames Research Center is described along with the flow field adjacent to an oscillating airfoil. The design and operational procedures of the tunnel are described in detail. Hydrogen bubble and thymol blue techniques are used to visualize the flow field. Results of the flow visualizations are presented in a series of still pictures and a high speed movie. These results show that time stall is more complicated than simple shedding from the leading edge or the trailing edge, particularly at relatively low frequency oscillations comparable to those of a helicopter blade. Therefore, any successful theory for predicting the stall loads on the helicopter blades must treat an irregular separated region rather than a discrete vortex passing over each blade surface.

Olsen, J. H.↗

NASA NTRS1976

Thin oblique airfoils at supersonic speed

Methods of thin airfoil theory have been extended to oblique or sweptback airfoils of finite aspect ratio moving at supersonic speeds. The cases considered thus far are symmetrical airfoils at zero lift having planforms bounded by straight lines. Because of the conical form of the elementary flow fields, the results are comparable in simplicity to the results of the two dimensional thin airfoil theory for subsonic speeds. In the case of untapered airfoils swept back behind the Mach cone the pressure distribution at the center section is similar to that given by the Ackeret theory for a straight airfoil. With increasing distance from the center section the distribution approaches the form given by the subsonic flow theory. The pressure drag is concentrated chiefly at the center section and or long wings a slight negative drag may appear on outboard sections.

Jones, R. T.↗

NASA NTRS1946

Thin oblique airfoils at supersonic speed

The well-known methods of thin-airfoil theory have been extended to oblique or sweptback airfoils of finite aspect ratio moving at supersonic speeds. The cases considered thus far are symmetrical airfoils at zero lift having plan forms bounded by straight lines. Because of the conical form of the elementary flow fields, the results are comparable in simplicity to the results of the two-dimensional thin-airfoil theory for subsonic speeds. In the case of untapered airfoils swept back behind the Mach cone the pressure distribution at the center section is similar to that given by the Ackeret theory for a straight airfoil. With increasing distance from the center section the distribution approaches the form given by the subsonic-flow theory. The pressure drag is concentrated chiefly at the center section and for long wings a slight negative drag may appear on outboard sections. (author)

Jone, Robert T↗

NASA NTRS2016

Characterization of Ice Roughness Variations in Scaled Glaze Icing Conditions

Because of the significant influence of surface tension in governing the stability and breakdown of the liquid film in flooded stagnation regions of airfoils exposed to glaze icing conditions, the Weber number is expected to be a significant parameter governing the formation and evolution of ice roughness. To investigate the influence of the Weber number on roughness formation, 53.3-cm (21-in.) and 182.9-cm (72-in.) NACA 0012 airfoils were exposed to flow conditions with essentially the same Weber number and varying stagnation collection efficiency to illuminate similarities of the ice roughness created on the different airfoils. The airfoils were exposed to icing conditions in the Icing Research Tunnel (IRT) at the NASA Glenn Research Center. Following exposure to the icing event, the airfoils were then scanned using a ROMER Absolute Arm scanning system. The resulting point clouds were then analyzed using the self-organizing map approach of McClain and Kreeger (2013) to determine the spatial roughness variations along the surfaces of the iced airfoils. The roughness characteristics on each airfoil were then compared using the relative geometries of the airfoil. The results indicate that features of the ice shape and roughness such as glaze-ice plateau limits and maximum airfoil roughness were captured well by Weber number and collection efficiency scaling of glaze icing conditions. However, secondary ice roughness features relating the instability and waviness of the liquid film on the glaze-ice plateau surface are scaled based on physics that were not captured by the local collection efficiency variations.

Roughness Formation↗

NASA NTRS2018

Ice Roughness and Thickness Evolution on a Business Jet Airfoil

Experiments were performed in the Icing Research Tunnel at NASA Glenn Research Center (GRC) to investigate the ice roughness and thickness evolution on a 152.4-cm (60-in.) chord business jet airfoil exposed to both Appendix C and Appendix O (SLD - Super-cooled Large Droplet) icing conditions. The resulting measurements demonstrate that the average non-dimensional roughness and the stagnation point thickness scalings are similar to those demonstrated on symmetric wings. However, the surface variations of roughness and thickness exhibit significant differences from those observed on symmetric airfoils. The source of the roughness and thickness differences is the result of surface pressure, velocity and temperature distribution differences from the suction to the pressure sides of the airfoil. LEWICE (LEWis ICE accretion program - software developed at NASA Lewis Research Center - former name of the GRC) simulations are used to further investigate the influences of local collection efficiency and the local freezing fraction on the resulting ice roughness and thickness spatial variations.

icing codes↗

NASA NTRS1973

New airfoil sections for general aviation aircraft

A program has been undertaken to develop new airfoil sections suitable for general aviation aircraft, utilizing theoretical and experimental advanced technology developed in recent years primarily for subsonic jet transport and military aircraft. The airfoil development program is one component of the Advanced Technology Light Twin program sponsored by NASA Langley Research Center. Two-dimensional tests of a new airfoil have demonstrated high cruising performance over a fairly wide C sub 1 range, and a C sub 1 max value of 3.69 with Fowler flap and no leading-edge devices. Experimental and theoretical development of additional configurations is under way.

Wentz, W. H., Jr.↗

NASA NTRS1982

Effect of thickness on airfoil surface noise

Noise emission from very small chord and very large chord airfoils was measured with eleven 0.63 cm microphones placed along a horizontal semicircle (4.57 m radius) that was centered at the leading edge of the test airfoil. The noise signals were analyzed by an automated spectrum analyzer which yielded 1/3-octave band sound pressure level spectra for each microphone, and the data were corrected to remove the effects of atmospheric attenuation and jet noise. It is found that the effect of thickness is large and must be accounted for in any fundamental airfoil noise theory that attempts to describe the noise emitted from real airfoils. Incident mean velocity gradients and compressibility must also be taken into account. The effect of thickness increases with frequency, with thick airfoils being quieter than thin ones.

Olsen, W.↗

NASA NTRS1993

Effect of an extendable slat on the stall behavior of a VR-12 airfoil

Experimental and computational tests were performed on a VR-12 airfoil to determine if the dynamic-stall behavior that normally accompanies high-angle pitch oscillations could be modified by segmenting the forward portion of the airfoil and extending it ahead of the main element. In the extended position the configuration would appear as an airfoil with a leading-edge slat, and in the retracted position it would appear as a conventional VR-12 airfoil. The calculations were obtained from a numerical code that models the vorticity transport equation for an incompressible fluid. These results were compared with test data from the water tunnel facility of the Aeroflightdynamics Directorate at Ames Research Center. Steady and unsteady flows around both airfoils were examined at angles of attack between 0 and 30 deg. The Reynolds number was fixed at 200,000 and the unsteady pitch oscillations followed a sinusoidal motion described by alpha = alpha(sub m) + 10 deg sin(omega t). The mean angle (alpha(sub m)) was varied from 10 to 20 deg and the reduced frequency from 0.05 to 0.20. The results from the experiment and the calculations show that the extended-slat VR-12 airfoil experiences a delay in both static and dynamic stall not experienced by the basic VR-12 airfoil.

Dehugues, P. Plantin↗

NASA NTRS1985

Low Reynolds number separation bubble research at UTRC

The facilities and techniques being applied in investigations of laminar separation bubbles on low Re airfoils at the United Technologies Research Center are described. The research is focused on developing a database and predictive models for use in designing compressor, fan and turbine blades. Flow data are gathered primarily by laser Doppler velocimetry. Experimental procedures are being devised which will permit formation of a short bubble for characterizations of the velocity profiles in and around the bubble and boundary layer. Further tests are directed at defining the size and location of the bubble and the transition in the separated shear layer. The sensitivity of the bubble to alterations in the Re, pressure gradient, turbulence intensity and the turbulence scales will be examined. The effects of surface curvature and roughness on the bubble will also be studied. Details of the wind tunnel facility and the steps being taken to define conditions for reliably producing the short bubble are outlined.

Patrick, W. P.↗

NASA NTRS1987

Development of wing and tail configurations for low altitude unmanned research aircraft (LAURA)

The Low Altitude/Airspeed Unmanned Research Aircraft (LAURA) is being developed by the U.S. Navy for flight test research using low-Reynolds number airfoils. This vehicle consists of a standard modular fuselage designed to accept the installation of several wings/tails having low Reynolds number airfoils, and various planform shapes. Design constraints include shipboard storage, long flight endurance at very low airspeeds and sea-skimming cruise altitude. The stringent design constraints require the development of high-performance low Reynolds number (LRN) airfoils, suitable lifting surface configuration, and advanced airframe-propulsion systems. The present paper describes ongoing efforts to develop wing and tail configurations for LAURA using airfoils designed at NASA Langley Research Center.

Mangalam, S. M.↗

NASA NTRS1994

Characteristics of surface roughness associated with leading edge ice accretion

Detailed size measurements of surface roughness associated with leading edge ice accretions are presented to provide information on characteristics of roughness and trends of roughness development with various icing parameters. Data was obtained from icing tests conducted in the Icing Research Tunnel (IRT) at NASA Lewis Research Center (LeRC) using a NACA 0012 airfoil. Measurements include diameters, heights, and spacing of roughness elements along with chordwise icing limits. Results confirm the existence of smooth and rough ice zones and that the boundary between the two zones (surface roughness transition region) moves upstream towards stagnation region with time. The height of roughness grows as the air temperature and the liquid water content increase, however, the airspeed has little effect on the roughness height. Results also show that the roughness in the surface roughness transition region grows during a very early stage of accretion but reaches a critical height and then remains fairly constant. Results also indicate that a uniformly distributed roughness model is only valid at a very initial stage of the ice accretion process.

Shin, Jaiwon↗

NASA NTRSDate not supplied

Fundamental Aeroelastic Analysis of an Urban Air Mobility Rotor

A computational investigation was conducted of the aeroelastic characteristics of a representative rotor typical of aircraft for Urban Air Mobility. A rotorcraft comprehensive analysis was used to examine the aeroelastic characteristics of the model, both in hover and in forward flight. Throughout the study, parameters examined included rotor rotational speed, forward flight speed, blade torsion stiffness, and chordwise locations of the blade elastic axis and center of gravity. Three sets of airfoil properties were analyzed: NACA 0012, VR8, and VR12. For hover, the effect of dynamic inflow was studied via a comparison of uniform inflow and dynamic inflow models. Thrust coefficient and blade tip twist were analyzed to ascertain performance characteristics, and eigen analysis was employed to determine stability. For the forward flight cases, rpm and forward flight speed were swept separately, and the effect of each on performance and stability was assessed. Thrust coefficient and mean drag coefficient were used to evaluate performance of the rotor, and eigen analysis was invoked to study rotor stability. Forward flight stability results generated via a constant coefficient analysis were compared with results generated via Floquet Theory.

Fundamental Aeroelastic Analysis↗

NASA NTRS2004

Probing Within the Boundary Layer of an Airfoil by Using the Wind Numerical Code

A detailed boundary layer investigation of an NACA 0012 airfoil was made by applying the WIND code at the NASA Glenn Research Center. Structured C-grids of selected configurations were fitted around the airfoil. Grids with dense spacing to capture the boundary layer provided for obtaining accurate results in this region. Concurrent with the boundary layer investigation, contour plots of overall performance of the airfoil were also obtained. A Mach number of 0.80, a Reynolds number of 4,000,000, and a zero angle of attack were set to correspond with numerical and experimental investigations reported in the literature, for comparison with the overall performance. The results were favorable for both the boundary layer investigations and the performance. As WIND evolves, it is intended to run WIND using unstructured grids to compare such results with the current structured grid results.

Cavicchi, Richard H.↗

NASA NTRS1979

Langley airfoil-research program

An overview of past, present, and future airfoil research activities at the Langley Research Center is given. The immediate past and future occupy most of the discussion; however, past accomplishments and milestones going back to the early NACA years are dealt with in a broad-brush way to give a better perspective of current developments and programs. In addition to the historical perspective, a short description of the facilities which are now being used in the airfoil program is given. This is followed by a discussion of airfoil developments, advances in airfoil design and analysis tools (mostly those that have taken place over the past 5 or 6 years), and tunnel-wall-interference predictive methods and measurements. Future research requirements are treated.

Bobbitt, P. J.↗

NASA NTRS1989

An airfoil pitch apparatus-modeling and control design

The study of dynamic stall of rapidly pitching airfoils is being conducted at NASA Ames Research Center. Understanding this physical phenomenon will aid in improving the maneuverability of fighter aircraft as well as civilian aircraft. A wind tunnel device which can linearly pitch and control an airfoil with rapid dynamic response is needed for such tests. To develop a mechanism capable of high accelerations, an accurate model and control system is created. The model contains mathematical representations of the mechanical system, including mass, spring, and damping characteristics for each structural element, as well as coulomb friction and servovalve saturation. Electrical components, both digital and analog, linear and nonlinear, are simulated. The implementation of such a high-performance system requires detailed control design as well as state-of-the-art components. This paper describes the system model, states the system requirements, and presents results of its theoretical performance which maximizes the structural and hydraulic aspects of this system.

Andrews, Daniel R.↗

NASA NTRS1989

An airfoil pitch apparatus-modeling and control design

The study of dynamic stall of rapidly pitching airfoils is being conducted at NASA Ames Research Center. Understanding this physical phenomenon will aid in improving the maneuverability of fighter aircraft as well as civilian aircraft. A wind tunnel device which can linearly pitch and control an airfoil with rapid dynamic reponse is needed for such tests. To develop a mechanism capable of high accelerations, an accurate model and control system is created. The model contains mathematical representations of the mechanical system, including mass, spring, and damping characteristics for each structural element, as well as coulomb friction and servovalve saturation. Electrical components, both digital and analog, linear and nonlinear, are simulated. The implementation of such a high-performance system requires detailed control design as well as state-of-the-art components. This paper describes the system model, states the system requirements, and presents results of its theoretical performance which maximizes the structural and hydraulic aspects of this system.

Andrews, Daniel R.↗