Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRSHIPS - RIGID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Radioisotope Stirling Engine Powered Airship for Low Altitude Operation on Venus

The feasibility of a Stirling engine powered airship for the near surface exploration of Venus was evaluated. The heat source for the Stirling engine was limited to 10 general purpose heat source (GPHS) blocks. The baseline airship utilized hydrogen as the lifting gas and the electronics and payload were enclosed in a cooled insulated pressure vessel to maintain the internal temperature at 320 K and 1 Bar pressure. The propulsion system consisted of an electric motor driving a propeller. An analysis was set up to size the airship that could operate near the Venus surface based on the available thermal power. The atmospheric conditions on Venus were modeled and used in the analysis. The analysis was an iterative process between sizing the airship to carry a specified payload and the power required to operate the electronics, payload and cooling system as well as provide power to the propulsion system to overcome the drag on the airship. A baseline configuration was determined that could meet the power requirements and operate near the Venus surface. From this baseline design additional trades were made to see how other factors affected the design such as the internal temperature of the payload chamber and the flight altitude. In addition other lifting methods were evaluated such as an evacuated chamber, heated atmospheric gas and augmented heated lifting gas. However none of these methods proved viable.

Colozza, Anthony J.↗
NASA NTRS1975

Feasibility study of modern airships, phase 1. Volume 2: Parametric analysis (task 3)

Various types of lighter-than-air vehicles from fully buoyant to semibuoyant hybrids were examined. Geometries were optimized for gross lifting capabilities for ellipsoidal airships, modified delta planform lifting bodies, and a short-haul, heavy-lift vehicle concept. It is indicated that: (1) neutrally buoyant airships employing a conservative update of materials and propulsion technology provide significant improvements in productivity; (2) propulsive lift for VTOL and aerodynamic lift for cruise significantly improve the productivity of low to medium gross weight ellipsoidal airships; and (3) the short-haul, heavy-lift vehicle, consisting of a simple combination of an ellipsoidal airship hull and existing helicopter componentry, provides significant potential for low-cost, near-term applications for ultra-heavy lift missions.

Lancaster, J. W.↗
NASA NTRS1975

Airship economics

Projected operating and manufacturing costs of a large airship design which are considered practical with today's technology and environment are discussed. Data and information developed during an 18-month study on the question of feasibility, engineering, economics and production problems related to a large metalclad type airship are considered. An overview of other classic airship designs are provided, and why metalclad was selected as the most prudent and most economic design to be considered in the 1970-80 era is explained. Crew operation, ATC and enroute requirements are covered along with the question of handling, maintenance and application of systems to the large airship.

Neumann, R. D.↗
NASA NTRS1975

Airship construction

Forty-four years ago the first successful metal airship was completed and delivered to the United States Navy, the ZMC-2. Between those years and the present, very little effort or serious consideration has been given to the manufacture, design, construction, or economic impact of airships. It is important to retain and exploit the small but continually diminishing pool of airship talent that will expedite the success of the United States in what is now a pioneering venture. The relative simplicity of airship construction, utilizing the tremendous technical advances of the last 44 years, leads to the conclusion that this form of transportation holds great promise for reducing costs of military missions and improving the international competitive position of the United States in commercial applications.

Roda, J.↗
NASA NTRS1975

The Slate all metal airship

The development of the Slate all metal airship City of Glendale built and completed in 1930 is presented. The airship facilities are discussed. Pertinent data which led to other engineering accomplishments for aviation are shown. The SMD-100 concept is presented along with a brief commentary on the costs and problems involved in such an airship design and the application of the hoisting and elevator facilities to airship development.

Slate, C. C.↗
NASA NTRS1975

State of the art of metalclad airships

Metalclad airship development of the past history are considered along with the immediate prospects for continuation of the development of these airships. The metalclad airships promise high safety even in highly inclement weather, are capable of high speeds, while lifting high useful loads. Metalclad airships which in first cost would compare favorably with the costs of sea-going ships and in operating costs promise to be lower than airplanes.

Pavlecka, V. H.↗
NASA NTRS1975

Roles of airships in economic development

It is proposed that airships of known and tested technology could, in some cases, perform routine transport missions more economically than conventional transport modes. If infrastructure for direct surface transport is already in place or if such infrastructure can be justified by the size of the market and there are no unusual impediments to constructing it, then the airships of tested technology cannot normally compete. If, however, the surface routes would be unusually expensive or circuitous, or if they involve several transhipments, or if the market size is too small to spread infrastructure costs of conventional transport, the airships of tested technology present a workable alternative. A series of special cases are considered. The cases, though unusual, are not unique; there are several similar possible applications which, in total, would provide a reasonably large market for airships.

Beier, G. J.↗
NASA NTRS1923

The drag of Zeppelin airships

This report is a discussion of the results of tests with Zeppelin airships, in which the propellers were stopped as quickly as possible while the airship was in full flight. In this paper the author refers to the theory involved in these tests and calls attention to one scientifically interesting fact which can be derived from the tests and which has not yet been noted. The most important question concerning the tests is, of course: does the negative acceleration of an airship with stopped propellers supply proper data for determining the drag of the airship when in uniform flight? This can not be absolutely answered, however, except that in this particular case the agreement is sufficient and that the data obtained from the test are the true quantities, or, at least, the approximate quantities wanted.

Munk, Max M↗
NASA NTRS1925

Determination of Turning Characteristics of an Airship by Means of a Camera Obscura

This investigation was carried out by the National Advisory Committee at Langley Field for the purpose of determining the adaptability of the camera obscura to the securing of turning characteristics of airships, and also of obtaining some of those characteristics of the C-7 airship. The method consisted in flying the airship in circling flight over a camera obscura and photographing it at known time intervals. The results show that the method used is highly satisfactory and that for the particular maneuver employed the turning diameter is 1,240 feet, corresponding to a turning coefficient of 6.4, and that the position of zero angle of yaw is at the nose of the airship.

Crowley, J W , Jr↗
NASA NTRS1926

Water Model Tests for Semirigid Airships

The design of complicated structures often presents problems of extreme difficulty which are frequently insoluble. In many cases, however, the solution can be obtained by tests on suitable models. These model tests are becoming so important a part of the design of new engineering structures that their theory has become a necessary part of an engineer's knowledge. For balloons and airships water models are used. These are models about 1/30 the size of the airship hung upside down and filled with water under pressure. The theory shows that the stresses in such a model are the same as in the actual airship. In the design of the Army Semirigid Airship RS-1 no satisfactory way was found to calculate the stresses in the keel due to the changing shape of the bag. For this purpose a water model with a flexible keel was built and tested. This report gives the theory of the design, construction, and testing of such a water model.

Tuckerman, L.B.↗
NASA NTRS1932

The drag characteristics of several airships determined by deceleration tests

This report presents the results of deceleration tests conducted for the purpose of determining the drag characteristics of six airships. The tests were made with airships of various shapes and sizes belonging to the Army, the Navy, and the Goodyear-Zeppelin Corporation. Drag coefficients for the following airships are shown: Army TC-6, TC-10, and TE-2; Navy Los Angeles and ZMC-2; Goodyear Puritan. The coefficients vary from about 0.045 for the small blunt airships to 0.023 for the relatively large slender Los Angeles. This variation may be due to a combination of effects, but the most important of these is probably the effect of length-diameter ratio.

Thompson, F L↗
NASA NTRS2004

Airships for Planetary Exploration

The feasibility of utilizing an airship for planetary atmospheric exploration was assessed. The environmental conditions of the planets and moons within our solar system were evaluated to determine their applicability for airship flight. A station-keeping mission of 50 days in length was used as the baseline mission. Airship sizing was performed utilizing both solar power and isotope power to meet the baseline mission goal at the selected planetary location. The results show that an isotope-powered airship is feasible within the lower atmosphere of Venus and Saturn s moon Titan.

Colozza, Anthony↗
NASA NTRS2005

High-Altitude, Long-Endurance Airships for Coastal Surveillance

A high altitude solar powered airship provides the ability to carry large payloads to high altitudes and remain on station for extended periods of time. This study examines applications and background of this type of concept vehicle, reviews the history of high altitude flight and provides a point design analysis. The capabilities and limitations of the airship are demonstrated and possible solutions are proposed. Factors such as time of year, latitude, wind speeds, and payload are considered in establishing the capabilities of the airship. East and west coast operation is evaluated. The key aspect to success of this type of airship is the design and operation of the propulsion and power system. A preliminary propulsion/power system design was produced based on a regenerative fuel cell energy storage system and solar photovoltaic array for energy production. Results on power system requirements for year long operation is presented.

Dolce, James L.↗
NASA NTRS2024

Enhancing Cargo Transportation by Reducing Airship Operating Costs

The cargo sector, contributing 8% of global greenhouse gas emissions, requires immediate action as the transportation industry gradually shifts towards greener energy solutions. In place of conventional cargo transportation, airships provide both an emission-free and cost-effective alternative. However, the cost of helium is increasing with time, making helium unsustainable to use for current state-of-the-art airships in the long term. This report explores and examines a variety of strategies and methods to make the transition to airships smoother, addressing cost concerns to ensure a beneficial shift for both aviation and cargo sectors. The main methods that have been explored and proposed are the conservation of helium through the usage of superheated steam, recycling helium using a cryogenic distillation system, ensuring the use of an efficient propulsion system, ensuring the use of an efficient electrical system—a hydrogen fuel system, and a path-finding algorithm (A* algorithm) to navigate through hazardous weather. By implementing these systems, sustainable airships can be achievable due to the concern of high-costs being greatly minimized.

Ahana Mitra↗
NASA NTRS1975

Description of CASCOMP Comprehensive Airship Sizing and Performance Computer Program, Volume 2

The computer program CASCOMP, which may be used in comparative design studies of lighter than air vehicles by rapidly providing airship size and mission performance data, was prepared and documented. The program can be used to define design requirements such as weight breakdown, required propulsive power, and physical dimensions of airships which are designed to meet specified mission requirements. The program is also useful in sensitivity studies involving both design trade-offs and performance trade-offs. The input to the program primarily consists of a series of single point values such as hull overall fineness ratio, number of engines, airship hull and empennage drag coefficients, description of the mission profile, and weights of fixed equipment, fixed useful load and payload. In order to minimize computation time, the program makes ample use of optional computation paths.

Davis, J.↗
NASA NTRS1975

Computer aided airship design

The Comprehensive Airship Sizing and Performance Computer Program (CASCOMP) is described which was developed and used in the design and evaluation of advanced lighter-than-air (LTA) craft. The program defines design details such as engine size and number, component weight buildups, required power, and the physical dimensions of airships which are designed to meet specified mission requirements. The program is used in a comparative parametric evaluation of six advanced lighter-than-air concepts. The results indicate that fully buoyant conventional airships have the lightest gross lift required when designed for speeds less than 100 knots and the partially buoyant concepts are superior above 100 knots. When compared on the basis of specific productivity, which is a measure of the direct operating cost, the partially buoyant lifting body/tilting prop-rotor concept is optimum.

Davis, S. J.↗
NASA NTRS1975

Effect of present technology on airship capabilities

The effect is presented of updating past airship designs using current materials and propulsion systems to determine new airship performance and productivity capabilities. New materials and power plants permit reductions in the empty weights and increases in the useful load capabilities of past airship designs. The increased useful load capability results in increased productivity for a given range, i.e., either increased payload at the same operating speed or increased operating speed for the same payload weight or combinations of both. Estimated investment costs and operating costs are presented to indicate the significant cost parameters in estimating transportation costs of payloads in cents per ton mile. Investment costs are presented considering production lots of 1, 10 and 100 units. Operating costs are presented considering flight speeds and ranges.

Madden, R. T.↗
NASA NTRS1975

A new concept for airship mooring and ground handling

Calculations were made to determine the feasibility of applying the negative air cushion (NAC) principle to the mooring of airships. Pressures required for the inflation of the flexible trunks are not excessive and the maintenance of sufficient hold down force is possible in winds up to 50 knots. Fabric strength requirements for a typical NAC sized for a 10-million cubic foot airship were found to be approximately 200 lbs./in. Corresponding power requirements range between 66-HP and 5600-HP. No consideration was given to the internal airship loads caused by the use of a NAC and further analysis in much greater detail is required before this method could be applied to an actual design, however, the basic concept appears to be sound and no problem areas of a fundamental nature are apparent.

Vaughan, J. C.↗