Search NASA⌕ Search

SEARCH · Search NASA

Results for “Adhesive Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Effect of metallurgical structure and properties on adhesion and friction behavior of cobalt alloys

The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.

Keller, D. V., Jr.↗
NASA NTRS1971

The development of autoclave processable, thermally stable adhesives for titanium alloy and graphite composite structures

The A-type polyimide adhesive resin P11B was modified by use of mixed diamines (thio-dianiline and meta phenylene diamine) which provided the desired autoclave processability. This new resin was termed P11BA. It was shown that copolymeric blends of P11BA and Amoco AI-1137 amide-imide resin provided improved adhesive properties when autoclave processed over the properties obtained previously by press bonding with P11B based copolymeric blended adhesives. Properties of bonded assemblies are presented for long-term aging at both elevated and low temperatures, and also stress-rupture tests at elevated temperature.

Vaughan, R. W.↗
NASA NTRS1981

Incorporation of metal related materials into electrically neutral polymers

Developments in the field of metal-containing polymers are reviewed with emphasis on neutral polymers incorporating dissolved metal salts, metal complexes, organometallic compounds, and metals. Polymer systems discussed include: polyamides, polyimides, polyalcohols, polyesters, polyacetylene, polyethylene, and polysiloxane. Most of the studies focus on the modification of polymer properties such as adhesive properties, thermal behavior, electrical conductivity, polymer flammability, and mechanical properties.

St. Clair, A. K.↗
NASA NTRS2011

Fiber-Reinforced Reactive Nano-Epoxy Composites

An ultra-high-molecular-weight polyethylene/ matrix interface based on the fabrication of a reactive nano-epoxy matrix with lower surface energy has been improved. Enhanced mechanical properties versus pure epoxy on a three-point bend test include: strength (25 percent), modulus (20 percent), and toughness (30 percent). Increased thermal properties include higher Tg (glass transition temperature) and stable CTE (coefficient of thermal expansion). Improved processability for manufacturing composites includes faster wetting rates on macro-fiber surfaces, lower viscosity, better resin infusion rates, and improved rheological properties. Improved interfacial adhesion properties with Spectra fibers by pullout tests include initial debonding force of 35 percent, a maximum pullout force of 25 percent, and energy to debond at 65 percent. Improved mechanical properties of Spectra fiber composites (tensile) aging resistance properties include hygrothermal effects. With this innovation, high-performance composites have been created, including carbon fibers/nano-epoxy, glass fibers/nano-epoxy, aramid fibers/ nano-epoxy, and ultra-high-molecularweight polyethylene fiber (UHMWPE).

Zhong, Wei-Hong↗
NASA NTRS1988

Thermoplastic adhesives based on 4,4'-isophthaloyldiphthalic anhydride (IDPA)

Thermoplastic polyimides were prepared and evaluated as adhesives. These materials are based on 4,4'-isophthaloyldiphathalic anhydride (IDAP) and either metaphenylene diamine (MPD) or 3,3'-diaminobenzophenone (DBAP). Both polymers exhibit excellent adhesive properties; however, the IDPA-MPD is the more attractive system because of a combination of high mechanical and physical properties as well as being made from commercially attractive monomers. The IDPA-MPD is an isomeric form of the commercially available adhesive and matrix resin, LARC-TPI and both systems have the same glass transition temperature and exhibit similar adhesive properties.

Progar, Donald J.↗
NASA NTRS2013

Treatment to Control Adhesion of Silicone-Based Elastomers

Seals are used to facilitate the joining of two items, usually temporarily. At some point in the future, it is expected that the items will need to be separated. This innovation enables control of the adhesive properties of silicone-based elastomers. The innovation may also be effective on elastomers other than the silicone-based ones. A technique has been discovered that decreases the level of adhesion of silicone- based elastomers to negligible levels. The new technique causes less damage to the material compared to alternative adhesion mitigation techniques. Silicone-based elastomers are the only class of rubber-like materials that currently meet NASA s needs for various seal applications. However, silicone-based elastomers have natural inherent adhesive properties. This stickiness can be helpful, but it can frequently cause problems as well, such as when trying to get items apart. In the past, seal adhesion was not always adequately addressed, and has caused in-flight failures where seals were actually pulled from their grooves, preventing subsequent spacecraft docking until the seal was physically removed from the flange via an extravehicular activity (EVA). The primary method used in the past to lower elastomer seal adhesion has been the application of some type of lubricant or grease to the surface of the seal. A newer method uses ultraviolet (UV) radiation a mixture of UV wavelengths in the range of near ultraviolet (NUV) and vacuum ultraviolet (VUV) wavelengths.

deGroh, Henry C., III↗
NASA NTRS1967

Nonwoven glass fiber mat reinforces polyurethane adhesive

Nonwoven glass fiber mat reinforces the adhesive properties of a polyurethane adhesive that fastens hardware to exterior surfaces of aluminum tanks. The mat is embedded in the uncured adhesive. It ensures good control of the bond line and increases the peel strength.

Roseland, L. M.↗
NASA NTRS1982

RF sputtered silicon and hafnium nitrides: Properties and adhesion to 440C stainless steel

Silicon nitride and hafnium nitride coatings were deposited by reactive RF sputtering on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. Depositions were at two background pressures, 8 and 20 mtorr, and at two different fractions (f) of nitrogen in argon, 0.25 and 0.60, for hafnium nitride and at f = 0.25 for silicon nitride. The coatings and the interface between the coating and substrates were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. A Knoop microhardness of 1650 + or - 100 kg/sq mm was measured for hafnium nitride and 3900 + or - 500 kg/sq mm for silicon nitride. The friction coefficients between a 440C rider and the coatings were measured under lubricated conditions. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C.

Grill, A.↗
NASA NTRS1982

Mechanical properties of adhesive systems at cryogenic and other temperatures

This paper presents a summary of the National Transonic Facility (NTF) fan blade adhesive characterization tests. Data was obtained at -300 F, room temperature (RT) and 200 F. The adhesive characterization data was acquired using specimens fabricated from materials orientated to simulate the lay up of the fan blades. Specimen fabrication, characterization tests, test equipment, test data, results and concluding remarks are reported. Adhesive test results are presented for specimens of the following types: lap shear, double lap shear, butt, short beam shear, flexure, and differential strain.

Staton, W. L.↗
NASA NTRS1983

RF-sputtered silicon and hafnium nitrides - Properties and adhesion to 440C stainless steel

Silicon nitride and hafnium nitride coatings were deposited by reactive RF sputtering on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. Depositions were at two background pressures, 8 and 20 mtorr, and at two different fractions (f) of nitrogen in argon, 0.25 and 0.60, for hafnium nitride and at f = 0.25 for silicon nitride. The coatings and the interface between the coating and substrates were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. A Knoop microhardness of 1650 + or 100 kg/sq mm was measured for hafnium nitride and 3900 + or 500 kg/sq mm for silicon nitride. The friction coefficients between a 440C rider and the coatings were measured under lubricated conditions. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C.

Grill, A.↗
NASA NTRS1976

Organic adhesives for hybrid microcircuits

Engineering design guidelines enumerate and briefly describe selected adhesive properties. General review of polymeric types of adhesives is included and major types of commercially available adhesives specifically designed for microelectronic use are identified.

Perkins, K. L.↗
NASA NTRS1974

Effect of Various Material Properties on the Adhesive Stage of Fretting

Various properties of metals and alloys were studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films were found to influence adhesion. High atomic density, low surface energy grain orientations exhibited lower adhesion than other orientations. Knowledge of interfacial surface binding energies assists in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents accomplishes both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1975

Effect of various material properties on the adhesive stage of fretting

Various properties of metals and alloys have been studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films have all been found to influence adhesion. High atomic density, low surface energy grain orientations exhibit lower adhesion than other orientations. Hexagonal metals in general manifest less adhesive wear than cubic metal. Knowledge of interfacial surface binding energies can assist in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents can accomplish both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1974

Effect of various material properties on the adhesive stage of fretting

Various properties of metals and alloys have been studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films have all been found to influence adhesion. High atomic density, low surface energy grain orientations exhibit lower adhesion than other orientations. Hexagonal metals in general manifest less adhesive wear than cubic metal. Knowledge of interfacial surface binding energies can assist in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents can accomplish both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1990

LARC-TPI 1500 series controlled molecular weight polyimide

LARC-TPI, a linear high temperature thermoplastic polyimide, was developed several years ago at NASA Langley Research Center. This material has been commercialized by Mitsui Toatsu Chemicals, Inc., Tokyo, Japan, as a varnish and powder. More recently, a melt-extruded film of a controlled molecular weight of this same polymer has been supplied to NASA Langley Research Center for evaluation. This new form, called LARC-TPI 1500 series, has been prepared in three molecular weights - high, medium and low flow polymers. The subject of this investigation deals with the rheological properties of the high and medium flow powders and the adhesive properties of the medium flow melt-extruded film. Rheological studies indicate that the high and medium flow forms of the polymer fall in the flow range of injection moldable materials. Adhesive data generated on the medium flow extruded film shows this form to be well suited for structural adhesive bonding. The data are as good or better than that for LARC-TPI data of previous studies.

Progar, Donald↗
NASA NTRS1980

Evaluation of high-temperature structural adhesives for extended service

Candidate high-temperature stable resin formulations were evaluated for adhesive properties when bonded to titanium treated with various surface preparations. The adhesive formulations included LARC-13, NR150 A2, NR150 B2, NR056X, FM-34, HR-602, and polyphenylquinoxaline. Eight titanium surface preparations were compared for resulting bond strength with the candidate adhesives. After initial evaluation, three adhesive systems (comprised of adhesive, primer, and titanium surface preparation) were selected for further screening. The screening (still in progress) includes cure-cycle optimization and bond properties from 219 K (-65 F) to 505 K (450 F), after isothermal aging at 505 K (450 F) up to 15,000 hours, and after humidity aging at 322 K 9120 F)/ 95 percent R. H. for up to 2000 hours. Larger-area bond capability of the three adhesive system can be demonstrated by fabrication of 30.5 cm (12 in) square titanium honeycomb sandwich and metal-to-metal bonded panels.

Hendricks, C. L.↗