Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aerodynamic levitation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Measuring the Density, Viscosity, and Surface Tension of Molten Titanates Using Electrostatic Levitation in Microgravity

Rare earth and barium titanates are useful as ferroelectric, dielectric, and optical materials. Measurements of their thermophysical properties in the liquid state can help guide melt processing technologies for their manufacture and advance understanding of fragile liquids' behavior and glass formation. Here, we report the density, thermal expansion, viscosity, and surface tension of molten BaTiNsub>2 O 5 , BaTi 4 O 9 , and 83TiO 2 -17RE 2 O 3 (RE = La or Nd). Measurements were made using electrostatic levitation and droplet oscillation techniques in microgravity, which provide access to quiescent liquid droplets and deep supercooling of 510–815 K below the equilibrium melting points. Densities were measured over 900–2400 K. Viscosities were similar for all four compositions, increasing from ∼10 mPa s near 2100 K to ∼30 mPa s near 1750 K. Surface tensions were 450–490 dyn cm −1 for the rare earth titanates and 383–395 dyn cm−1 for the barium titanates; surface tensions of all compositions had small or negligible temperature dependence over 1700–2200 K. For solids recovered after melt quenching, x-ray microtomography revealed the fracture mechanics in crystalline products and minimal internal porosity in glass products, likely arising from entrapped gas bubbles. Internal microstructures were generally similar for products processed either in microgravity or in a terrestrial aerodynamic levitator.

Stephen K Wilke↗
DOE OSTI2024

Measuring the density, viscosity, and surface tension of molten titanates using electrostatic levitation in microgravity

Rare earth and barium titanates are useful as ferroelectric, dielectric, and optical materials. Measurements of their thermophysical properties in the liquid state can help guide melt processing technologies for their manufacture and advance understanding of fragile liquids' behavior and glass formation. Here, we report the density, thermal expansion, viscosity, and surface tension of molten BaTi 2 O 5 , BaTi 4 O 9 , and 83TiO 2 -17RE 2 O 3 (RE = La or Nd). Measurements were made using electrostatic levitation and droplet oscillation techniques in microgravity, which provide access to quiescent liquid droplets and deep supercooling of 510–815 K below the equilibrium melting points. Densities were measured over 900–2400 K. Viscosities were similar for all four compositions, increasing from ~10 mPa s near 2100 K to ~30 mPa s near 1750 K. Surface tensions were 450–490 dyn cm -1 for the rare earth titanates and 383–395 dyn cm -1 for the barium titanates; surface tensions of all compositions had small or negligible temperature dependence over 1700–2200 K. In conclusion, for solids recovered after melt quenching, x-ray microtomography revealed the fracture mechanics in crystalline products and minimal internal porosity in glass products, likely arising from entrapped gas bubbles. Internal microstructures were generally similar for products processed either in microgravity or in a terrestrial aerodynamic levitator.

42 ENGINEERING↗
DOE OSTI2022

Tuning the melting point and phase stability of rare-earth oxides to facilitate their crystal growth from the melt

The challenge of growing rare-earth (RE) sesquioxide crystals can be overcome by tailoring their structural stability and melting point via composition engineering. This work contributes to the advancement of the field of crystal growth of high-entropy oxides. A compound with only small REs (Lu,Y,Ho,Yb,Er) 2 O 3 maintains a cubic C-type structure upon cooling from the melt, as observed via in-situ high-temperature neutron diffraction on aerodynamically levitated samples. On the other hand, a compound with a mixture of small and large REs (Lu,Y,Ho,Nd,La) 2 O 3 crystallizes as a mixture of a primary C-type phase with an unstable secondary phase. Crystals of compositions (Lu,Y,Ho,Nd,La) 2 O 3 and (Lu,Y,Gd,Nd,La) 2 O 3 were grown by the micro-pulling-down (mPD) method with a single monoclinic B-type phase, while a powder of (Lu,Y,Ho,Yb,Er) 2 O 3 did not melt at the maximum operating temperature of an iridium-rhenium crucible. The minimization of the melting point of the two grown crystals is attributed to the mismatch in cation sizes. The electron probe microanalysis reveals that the general element segregation behavior in the crystals depends on the composition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Plutonium oxide melt structure and covalency

Advances in nuclear power reactors include the use of mixed oxide fuel, containing uranium and plutonium oxides. The high-temperature behaviour and structure of PuO 2-x above 1,800 K remain largely unexplored, and these conditions must be considered for reactor design and planning for the mitigation of severe accidents. Here, in this study, we measure the atomic structure of PuO 2-x through the melting transition up to 3,000 +/- 50 K using X-ray scattering of aerodynamically levitated and laser-beam-heated samples, with O/Pu ranging from 1.57 to 1.76. Liquid structural models consistent with the X-ray data are developed using machine-learned interatomic potentials and density functional theory. Molten PuO 1.76 contains some degree of covalent Pu-O bonding, signalled by the degeneracy of Pu 5f and O 2p orbitals. The liquid is isomorphous with molten CeO 1.75 , demonstrating the latter as a non-radioactive, non-toxic, structural surrogate when differences in the oxidation potentials of Pu and Ce are accounted for. These characterizations provide essential constraints for modelling pertinent to reactor safety design. The molten structure of plutonium oxide-a component of mixed oxide nuclear fuels-is measured, showing some degree of covalent bonding. Its atomic structure is similar to that of cerium oxide, which could be a non-radioactive structural surrogate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Phase separation in mullite-composition glass

Aluminosilicates (AS) are ubiquitous in ceramics, geology, and planetary science, and their glassy forms underpin vital technologies used in displays, waveguides, and lasers. In spite of this, the nonequilibrium behavior of the prototypical AS compound, mullite (40SiO 2 -60Al 2 O 3 , or AS60), is not well understood. By deeply supercooling mullite-composition liquid via aerodynamic levitation, we observe metastable liquid–liquid unmixing that yields a transparent two-phase glass, comprising a nanoscale mixture of AS7 and AS62. Extrapolations from X-ray scattering measurements show the AS7 phase is similar to vitreous SiO 2 with a few Al species substituted for Si. The AS62 phase is built from a highly polymerized network of 4-, 5-, and 6-coordinated AlO x polyhedra. Polymerization of the AS62 network and the composite morphology provide essential mechanisms for toughening the glass.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Boron coordination change in barium borate melts and glasses and its contribution to configurational heat capacity, entropy, and fragility

High-energy x-ray diffraction from molten and glassy BaB 2 O 4 and BaB 4 O 7 has been performed using aerodynamic levitation and laser heating over a wide range of temperatures. Remarkably, even in the presence of a heavy metal modifier dominating x-ray scattering, it was possible to extract accurate values for the tetrahedral, sp 3 , boron fraction, N 4 , which declines with increasing temperature, using bond valence-based mapping from the measured mean B–O bond lengths while accounting for vibrational thermal expansion. These are used within a boron-coordination-change model to extract enthalpies, ΔH, and entropies, ΔS, of isomerization between sp 2 and sp 3 boron. The results for BaB 4 O 7 , ΔH = 22(3) kJ mol -1 boron, ΔS = 19(2) J mol -1 boron K -1 , agree quantitatively with those found previously for Na 2 B 4 O 7 . Analytical expressions for N 4 (J, T) and associated configurational heat capacity, $C_{P}^{conf}$(J, T), and entropy, S conf (J, T), contributions are extended to cover a wide composition range 0 ≤ J = BaO/B 2 O 3 ≤ 3 using a model for ΔH(J) and ΔS(J) derived empirically for lithium borates. Maxima in the $C_{P}^{conf}$(J, T g ) and fragility index contributions are thereby predicted for J ≲ 1, higher than the maximum observed and predicted in N 4 (J, T g ) at J ≃ 0.6. We discuss the utility of the boron-coordination-change isomerization model in the context of borate liquids containing other modifiers and the prospect of neutron diffraction to aid in empirical determinations of modifier-dependent effects, illustrated by new neutron diffraction data on Ba 11 B 4 O 7 glass, its well-known α-polymorph, and lesser-known δ-phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Structure–property relations of binary ferrite melts

Molten ferrite systems are used in the smelting and refining processes in steelmaking, to reduce the loss of metals in slags and to accelerate reaction rates. Here, high-energy x-ray diffraction experiments have been performed on aerodynamically levitated molten spheres of 43BaO–57FeO X and 43SrO–57FeO X at 1873 K using laser beam heating. The composition was varied within the range of x = 1–1.5 by changing the oxygen partial pressure of the levitation gas. The corresponding x-ray pair distribution functions have been interpreted using empirical potential structure refinement (EPSR) modeling. In oxygen-rich melts (x = 1.5), our EPSR models indicate very similar structures for the different alkaline-earth liquids, with both the Ba–O and Sr–O coordination numbers to be ∼8.4 and the total Fe–O coordination numbers ∼5.7. However, our models show that in reducing environments, the Fe 3+ and Fe 2+ ions exhibit very different behaviors in the Ba- and Sr-ferrite liquids. In the Ba-ferrite melt, the Fe 3+ –O coordination number decreases from 5.7 (at x = 1.5) to 5.2 (at x = 1.07), whereas Fe 2+ –O remains constant at ∼5.0 across the same compositional range. In the Sr melts, both the Fe 2+ –O and Fe 3+ –O coordination numbers rise from ∼5.7 (at x = 1.5) to 6.3 (at x = 1.07). All models show the structures to be heterogeneous with intertwined nanometer sized clusters or channels of Ba/Sr–O and Fe–O polyhedra that grow as oxygen content is reduced. Changes in the viscosity and electrical properties are interpreted in terms of the number of bridging and non-bridging oxygens associated with FeO 4 tetrahedra and concentration of charge carriers, respectively.

Benmore, Chris J. [Argonne National Laboratory (AN↗
DOE OSTI2021

Hard x-ray methods for studying the structure of amorphous thin films and bulk glassy oxides

High-energy photon diffraction minimizes many of the corrections associated with laboratory x-ray diffractometers, and enables structure factor measurements to be made over a wide range of momentum transfers. The method edges us closer toward an ideal experiment, in which coordination numbers can be extracted without knowledge of the sample density. Three case studies are presented that demonstrate new hard x-ray methods for studying the structure of glassy and amorphous materials. First, the methodology and analysis of high-energy grazing incidence on thin films is discussed for the case of amorphous In 2 O 3 . Additionally, the connectivity of irregular InO 6 polyhedra are shown to exist in face-, edge- and corner-shared configurations in the approximate ratio of 1:2:3. Secondly, the technique of high-energy small and wide angle scattering has been carried out on laser heated and aerodynamically levitated samples of silica-rich barium silicate (20BaO:80SiO 2 ), from the single phase melt at 1500 C-o to the phase separated glass at room temperature. Based on Ba-O coordination numbers of 6 to 7, it is argued that the although the potential of Ba is ionic, it is weak enough to cause the liquid-liquid immiscibility to become metastable. Lastly, high-energy small and wide angle scattering has also been applied to high water content (up to 12 wt.%) samples of hydrous SiO 2 glass quenched from 1500 C-o at 4 GPa. An increase of Si 1 O 2 correlations at 4.3 angstrom is found to be consistent with an increase in the population of three-membered SiO 4 rings at the expense of larger rings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Preface to the JPCM special issue on intense radiation sources in condensed matter and materials physics

This special issue is designed to honour the contributions of our colleague Neville Greaves who was among the first to apply newly-available synchrotron x-ray techniques to study the synthesis, structures and properties of advanced materials [1, 2]. His wide ranging work on ceramics, glasses and nanomaterials was celebrated in a recent issue of the J. Non-Cryst. Solids [3]. Neville's contributions to synchrotron research, highlighted here, focussed on design and construction of new beamline capabilities and sample environments to probe materials under different physical and chemical conditions, integrating various techniques to obtain complementary data on structure and bonding. The innovative nature of his work is illustrated by his studies of liquids and glasses, where he incorporated aerodynamic levitation into these experimental techniques, using both synchrotron x-ray and neutron beams to probe the structural transformations and dynamics combined with molecular dynamics simulations to study atomic scale organisation. His work has had a major impact on fundamental condensed matter physics and chemistry as well as applied materials science; and in this issue, we present contributions from colleagues using and developing new experimental techniques at current and next-generation synchrotron, neutron and free-electron laser sources and in their own laboratories, that probe the fundamental physics, chemistry and functional properties of novel materials and processes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

The structure of molten calcium ferrite under various redox conditions

Laser-heated melts based on the 43CaO–57Fe 2 O 3-x eutectic, close to the calcium ferrite (CF) composition, were measured with high-energy X-ray diffraction using aerodynamic levitation over a range of redox states controlled by CO/CO 2 gas atmospheres. The iron–oxygen coordination number was found to rise from 4.4 ± 0.3 at 15% Fe 3+ to 5.3 ± 0.3 at 87% Fe 3+ . Empirical potential structure refinement modelling was used to obtain the ferric and ferrous partial pair distribution functions. It was found that the Fe 2+ iron–oxygen coordination number is consistently approximately 10% higher in CF than in pure iron oxide, while Fe 3+ is essentially identical in all but the most oxygen-rich environments (where it is higher in CF compared with FeO x ). The model also shows calcium octahedra to be the dominant species across all redox environments, although the population of CaO 7 increases with the availability of oxygen at the expense of CaO 4 and CaO 5 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

The structure of CaO–MgO–Al 2 O 3 –SiO 2 melts and glasses doped with FeO X –NiO

Neutron and x-ray diffraction measurements have been performed on CaO–MgO–Al 2 O 3 –SiO 2 (CMAS) glasses doped with NiO–Fe X O at room temperature, along with x-ray measurements on aerodynamically levitated liquids at ≥2000 K. The disordered structures have been modeled using empirical potential structure refinement to investigate the relation between the aluminosilicate network and the modifying cations. The SiO 4 and AlO 4 tetrahedra are found to have wider Si–O and Al–O bond distance distributions in the glass, and the first Ca–O n coordination shell is highly distorted, redistributing different populations of long and short bonds between the liquid and the glass. The addition of Fe and Ni at low aluminosilicate content increases the number of free oxygens not bonded to AlO 4 or SiO 4 . Mg–O and Fe–O are both found to be predominantly fourfold and fivefold in the liquid and glassy states. Despite these low coordination numbers, their bond angle distributions indicate that they are predominantly in nontetrahedral-type geometries, with ferrous and ferric iron possessing similar coordination environments. The Ca–O and Mg–O average coordination numbers and enthalpies of solution are consistent with their higher reactivity within relatively acidic aluminosilicate melts.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Fluid mechanics and solidification investigations in low-gravity environments

Fluid mechanics of gases and liquids and solidification processes were investigated under microgravity conditions during Skylab and Apollo-Soyuz missions. Electromagnetic, acoustic, and aerodynamic levitation devices, drop tubes, aircraft parabolic flight trajectories, and vertical sounding rockets were developed for low-g simulation. The Spacelab 3 mission will be carried out in a gravity gradient flight attitude; analyses of sources of vehicle dynamic accelerations with associated g-levels and angular rates will produce results for future specific experiments.

Fichtl, G. H.↗
NASA NTRS1990

NASA-sponsored containerless processing experiments

An outline is presented of containerless processing and facilities at Intersonics which is sponsored by NASA. There are electromagnetic, acoustic, and aerodynamic levitation facilities. There are also laser beam and arc lamp heating systems along with state of the art noncontact temperature and optical property measurement facilities. Nonintrusive diagnostic techniques with Laser Induced Fluorescence and mass spectrometer are also available. Controlled atmosphere processing, gas quenching, and proven microgravity processing technology is part of the Intersonics capabilities.

Hofmeister, William H.↗
NASA NTRS1994

Containerless liquid-phase processing of ceramic materials

Containerless melting and solidification provides a powerful tool for investigation and synthesis of ceramic and glass materials. The work described in this article explored and extended the limits of ground-based experimentation by using aero-acoustic and aerodynamic levitation in combination with laser beam heating and melting to investigate ceramic and glass processing. Results of liquid-phase processing experiments on calcia-gallia and calcia-gallia-silica glass-forming mixtures, aluminum oxide, and ceramic superconductors are summarized. The work is discussed in the context of low gravity experimental and materials synthesis requirements and opportunities.

Weber, J. K. R.↗
NASA NTRS1996

Aerodynamics of magnetic levitation (MAGLEV) trains

High-speed (500 kph) trains using magnetic forces for levitation, propulsion and control offer many advantages for the nation and a good opportunity for the aerospace community to apply 'high tech' methods to the domestic sector. One area of many that will need advanced research is the aerodynamics of such MAGLEV (Magnetic Levitation) vehicles. There are important issues with regard to wind tunnel testing and the application of CFD to these devices. This talk will deal with the aerodynamic design of MAGLEV vehicles with emphasis on wind tunnel testing. The moving track facility designed and constructed in the 6 ft. Stability Wind Tunnel at Virginia Tech will be described. Test results for a variety of MAGLEV vehicle configurations will be presented. The last topic to be discussed is a Multi-disciplinary Design approach that is being applied to MAGLEV vehicle configuration design including aerodynamics, structures, manufacturability and life-cycle cost.

Schetz, Joseph A.↗
NASA NTRS1991

Containerless high temperature property measurements

Containerless processing in the low gravity environment of space provides the opportunity to increase the temperature at which well controlled processing of and property measurements on materials is possible. This project was directed towards advancing containerless processing and property measurement techniques for application to materials research at high temperatures in space. Containerless high temperature material property studies include measurements of the vapor pressure, melting temperature, optical properties, and spectral emissivities of solid boron. The reaction of boron with nitrogen was also studied by laser polarimetric measurement of boron nitride film growth. The optical properties and spectral emissivities were measured for solid and liquid silicon, niobium, and zirconium; liquid aluminum and titanium; and liquid Ti-Al alloys of 5 to 60 atomic pct. titanium. Alternative means for noncontact temperature measurement in the absence of material emissivity data were evaluated. Also, the application of laser induced fluorescence for component activity measurements in electromagnetic levitated liquids was studied, along with the feasibility of a hybrid aerodynamic electromagnetic levitation technique.

Nordine, Paul C.↗
NASA NTRS1982

Levitator for Containerless Processing

Objects are levitated by aerodynamic forces in an apparatus originally developed for space research but just as effective on Earth. New levitator is orientation-independent. Also works equally as well whether or not gravity is present. Apparatus supports a sphere by aerodynamic forces from gas flowing through convergent/divergent section. Concentric inner tube is moved along axis of cylindrical housing.

Berg, L. H.↗
NASA NTRS1996

Magnetic levitation systems for future aeronautics and space research and missions

The objectives, advantages, and research needs for several applications of superconducting magnetic levitation to aerodynamics research, testing, and space-launch are discussed. Applications include very large-scale magnetic balance and suspension systems for high alpha testing, support interference-free testing of slender hypersonic propulsion/airframe integrated vehicles, and hypersonic maglev. Current practice and concepts are outlined as part of a unified effort in high magnetic fields R&D within NASA. Recent advances in the design and construction of the proposed ground-based Holloman test track (rocket sled) that uses magnetic levitation are presented. It is protected that ground speeds of up to Mach 8 to 11 at sea-level are possible with such a system. This capability may enable supersonic combustor tests as well as ramjet-to-scramjet transition simulation to be performed in clean air. Finally a novel space launch concept (Maglifter) which uses magnetic levitation and propulsion for a re-usable 'first stage' and rocket or air-breathing combined-cycle propulsion for its second stage is discussed in detail. Performance of this concept is compared with conventional advanced launch systems and a preliminary concept for a subscale system demonstration is presented.

Blankson, Isaiah M.↗