Search NASA⌕ Search

SEARCH · Search NASA

Results for “American Made”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1949

Supplementary Ditching Investigation of a 1/18-Scale Model of the North American B-45 Airplane

A supplementary investigation of a 1/18-scale dynamically similar model of the North American B-45 airplane was made in calm water to observe the ditching behavior and to determine the effect of further conditions of simulated damage. The behavior of the model was determined from motion-picture records, time-history deceleration records, and visual observations. It was concluded that, during a ditching, the nose-wheel doors, bomb-bay doors, under surface of the aft fuselage and lower part of the bomb-bay aft bulkhead will be torn away. When such damage occurs, the diving found in the previous tests will not occur and the airplane will porpoise during the first third of the landing run and then run smoothly. Because of the extensive damage which occurs, the fuselage aft of the pilots' compartment will fill with water very rapidly and is, therefore, an undesirable ditching station. No change in the previously recommended ditching attitude and flap setting (6 deg attitude, flaps down) is indicated by these supplementary tests.

Fisher, Lloyd J.↗
NASA NTRS1949

Ditching Investigation of a 1/18-Scale Model of the North American B-45 Airplane

An investigation of a 1/18-scale dynamically similar model of the North American B-45 airplane was made to observe the ditching behavior and determine the proper landing technique to be used in an emergency water landing. Various conditions of damage were simulated to determine the behavior which probably would occur in a full-scale ditching. The behavior of the model was determined from high-speed motion-picture records, time-history acceleration records, and visual observations. It was concluded that the airplane should be ditched at the maximum nose-high attitude with the landing flaps full down for minimum landing speed. During the ditching, the nose-wheel and bomb-bay doors probably will be torn away and the rear of the fuselage flooded. A violent dive will very likely occur. Longitudinal decelerations of approximately 5g and vertical accelerations of approximately -6g (including gravity) will be experienced near the pilots' compartment. Ditching braces installed in the bomb bay will tend to improve the behavior slightly but will be torn away along with the bomb-bay doors. A hydroflap installed ahead of the nose-wheel doors will eliminate the dive and failure of the nose-wheel doors, and substantially reduce the motions and accelerations.

Fisher, Lloyd J.↗
NASA NTRS1948

Measurements of the Longitudinal Stability and Control and Stalling Characteristics of a North American P-51H Airplane (AAF No. 4-64164)

Flight tests have been made to determine the longitudinal stability and control and stalling characteristics of a North American P-51H airplane. The results indicate that the airplane has satisfactory longitudinal stability in all the flight conditions tested at normal loadings up to 25,000 feet altitude. At Mach numbers above 0.7, the elevator push force required for longitudinal trim decreased somewhat because of compressibility effects. The elevator stick force per g in accelerated turns at the forward center-of-gravity position of 24 percent mean aerodynamic chord above 250 miles per hour was in excess of the required limits at both 5,000 and 25,OOO feet altitude. The longitudinal-trim-force changes due to flaps and power were small, but the rudder-trim-force change with power change was high. The stalling characteristics in all the conditions tested were satisfactory.

Kraft, Christopher C., Jr.↗
NASA NTRS1950

Static Longitudinal Stability of a Tandem-Coupled Bomber-Fighter Airplane Configuration Proposed by All American Airways, Inc.

At the request of the Air Materiel Command an investigation was made in the Langley free-flight tunnel to determine the static longitudinal stability and control characteristics of models coupled together in a tandem configuration proposed by All American Airways, Inc. Force tests were made using 1/20-scale models of B-29 end F-80 airplanes to determine the effects of coupling the fighter to the tail of the bomber. The results of the investigation showed that for the bomber alone the aerodynamic center was 0.21 mean aerodynamic chord behind the center of gravity (stable) but that for the tandem configuration the aerodynamic center was 0.09 mean aerodynamic chord forward of the center of gravity, of the combination (unstable). The elevator effectiveness of the bomber was reduced approximately 50 percent by addition of the fighter. Some recent flight tests made in the free-flight tunnel with models simulating the proposed configuration indicate that the reduction in stability may be minimized by incorporating a hinged coupling permitting freedom in pitch.

Hewes, Donald E.↗
NASA NTRS2005

Materials Examination of the Vertical Stabilizer from American Airlines Flight 587

The first in-flight failure of a primary structural component made from composite material on a commercial airplane led to the crash of American Airlines Flight 587. As part of the National Transportation Safety Board investigation of the accident, the composite materials of the vertical stabilizer were tested, microstructure was analyzed, and fractured composite lugs that attached the vertical stabilizer to the aircraft tail were examined. In this paper the materials testing and analysis is presented, composite fractures are described, and the resulting clues to the failure events are discussed.

Fox, Matthew R.↗
NASA NTRS1954

Free-Flight Tests of 0.11-Scale North American F-100 Airplane Wings to Investigate the Possibility of Flutter in Transonic Speed Range at Varying Angles of Attack

Free-flight tests in the transonic speed range utilizing rocketpropelled models have been made on three pairs of 0.11-scale North American F-100 airplane wings having an aspect ratio of 3.47, a taper ratio of 0.308, 45 degree sweepback at the quarter-chord line, and thickness ratios of 31 and 5 percent to investigate the possibility of flutte r. Data from tests of two other rocket-propelled models which accidentally fluttered during a drag investigation of the North American F-100 airplane are also presented. The first set of wings (5 percent thick) was tested on a model which was disturbed in pitch by a moving tail and reached a maximum Mach number of 0.85. The wings encountered mild oscillations near the first - bending frequency at high lift coefficients. The second set of wings 9 percent thick was tested up to a maximum Mach number of 0.95 at (2) angles of attack provided by small rocket motors installed in the nose of the model. No oscillations resembling flutter were encountered during the coasting flight between separation from the booster and sustainer firing (Mach numbers from 0.86 to 0.82) or during the sustainer firing at accelerations of about 8g up to the maximum Mach number of the test (0.95). The third set of wings was similar to the first set and was tested up to a maximum Mach number of 1.24. A mild flutter at frequencies near the first-bending frequency of the wings was encountered between a Mach number of 1.15 and a Mach number of 1.06 during both accelerating and coasting flight. The two drag models, which were 0.ll-scale models of the North American F-100 airplane configuration, reached a maximum Mach number of 1.77. The wings of these models had bending and torsional frequencies which were 40 and 89 percent, respectively, of the calculated scaled frequencies of the full-scale 7-percent-thick wing. Both models experienced flutter of the same type as that experienced-by the third set of wings.

O'Kelly, Burke R.↗
NASA NTRS1986

Compendium of meteorology scientific issues of 1950 still outstanding

The Compendium of Meteorology was published in 1951 by the American Meteorological Society. A review was made of the Compendium of Meteorology to identify the studies and future needs which the authors expressed in their papers. The needs as seen by the authors are organized into sections and papers following the format of the Compendium of Meteorology. In some cases the needs they identified are as valid today as they were in 1951. In other cases one will easily be able to identify examples where significant progress has been made. It is left to the individual scientists and scientific program managers to assess whether significant progress has been made over the past thirty-five years on these outstanding scientific issues.

Vaughan, W. W.↗
NASA NTRS1995

HF radar signatures of the cusp and low-latitude boundary layer

Continuous ground-based observations of ionospheric and magnetospheric regions are critical to the Geospace Environmental Modeling (GEM) program. It is therefore important to establish clear intercalibrations between different ground-based instruments and satellites in order to clearly place the ground-based observations in context with the corresponding in situ satellite measurements. HF-radars operating at high latitudes are capable of observing very large spatial regions of the ionosphere on a nearly continuous basis. In this paper we report on an intercalibration study made using the Polar Anglo-American Conjugate Radar Experiment radars located at Goose Bay, Labrador, and Halley Station, Antarctica, and the Defense Meteorological Satellite Program (DMSP) satellites. The DMSP satellite data are used to provide clear identifications of the ionospheric cusp and the low-latitude boundary layer (LLBL). The radar data for eight cusp events and eight LLBL events have been examined in order to determine a radar signature of these ionospheric regions. This intercalibraion indicates that the cusp is always characterized by wide, complex Doppler power spectra, whereas the LLBL is usually found to have spectra dominated by a single component. The distribution of spectral widths in the cusp is of a generally Gaussian form with a peak at about 220 m/s. The distribution of spectral widths in the LLBL is more like an exponential distribution, with the peak of the distribution occurring at about 50 m/s. There are a few cases in the LLBL where the Doppler power spectra are strikingly similar to those observed in the cusp.

Baker, K. B.↗
NASA NTRS1959

Launch, Low-Speed, and Landing Characteristics Determined from the First Flight of the North American X-15 Research Airplane

The first flight of the North American X-15 research airplane was made on June 8, 1959. This was accomplished after completion of a series of captive flights with the X-15 attached to the B-52 carrier airplane to demonstrate the aerodynamic and systems compatibility of the X-15//B-52 combination and the X-15 subsystem operation. This flight was planned as a glide flight so that the pilot need not be concerned with the propulsion system. Discussions of the launch, low-speed maneuvering, and landing characteristics are presented, and the results are compared with predictions from preflight studies. The launch characteristics were generally satisfactory, and the X-15 vertical tail adequately cleared the B-52 wing cutout. The actual landing pattern and landing characteristics compared favorably with predictions, and the recommended landing technique of lowering the flaps and landing gear at a low altitude appears to be a satisfactory method of landing the X-15 airplane. There was a quantitative correlation between flight-measured and predicted lift-drag-ratio characteristics in the clean configuration and a qualitative correlation in the landing configuration. A longitudinal-controllability problem, which became severe in the landing configuration, was evident throughout the flight and, apparently, was aggravated by the sensitivity of the side-located control stick. In the low-to-moderate angle-of-attack range covered, the longitudinal and directional stability were indicated to be adequate.

Finch, Thomas W.↗
NASA NTRS2015

Ocean-Atmosphere Coupled Model Simulations of Precipitation in the Central Andes

The meridional extent and complex orography of the South American continent contributes to a wide diversity of climate regimes ranging from hyper-arid deserts to tropical rainforests to sub-polar highland regions. In addition, South American meteorology and climate are also made further complicated by ENSO, a powerful coupled ocean-atmosphere phenomenon. Modelling studies in this region have typically resorted to either atmospheric mesoscale or atmosphere-ocean coupled global climate models. The latter offers full physics and high spatial resolution, but it is computationally inefficient typically lack an interactive ocean, whereas the former offers high computational efficiency and ocean-atmosphere coupling, but it lacks adequate spatial and temporal resolution to adequate resolve the complex orography and explicitly simulate precipitation. Explicit simulation of precipitation is vital in the Central Andes where rainfall rates are light (0.5-5 mm hr-1), there is strong seasonality, and most precipitation is associated with weak mesoscale-organized convection. Recent increases in both computational power and model development have led to the advent of coupled ocean-atmosphere mesoscale models for both weather and climate study applications. These modelling systems, while computationally expensive, include two-way ocean-atmosphere coupling, high resolution, and explicit simulation of precipitation. In this study, we use the Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST), a fully-coupled mesoscale atmosphere-ocean modeling system. Previous work has shown COAWST to reasonably simulate the entire 2003-2004 wet season (Dec-Feb) as validated against both satellite and model analysis data when ECMWF interim analysis data were used for boundary conditions on a 27-9-km grid configuration (Outer grid extent: 60.4S to 17.7N and 118.6W to 17.4W).

Regional Climate Model↗
NASA NTRS2017

The Power for Flight: NASA's Contributions to Aircraft Propulsion

The New York Times announced America's entry into the 'long awaited' Jet Age when a Pan American (Pan Am) World Airways Boeing 707 airliner left New York for Paris on October 26, 1958. Powered by four turbojet engines, the 707 offered speed, more nonstop flights, and a smoother and quieter travel experience compared to newly antiquated propeller airliners. With the Champs-Elysees only 6 hours away, humankind had entered into a new and exciting age in which the shrinking of the world for good was no longer a daydream. Fifty years later, the New York Times declared the second coming of a 'cleaner, leaner' Jet Age. Decades-old concerns over fuel efficiency, noise, and emissions shaped this new age as the aviation industry had the world poised for 'a revolution in jet engines'. Refined turbofans incorporating the latest innovations would ensure that aviation would continue to enable a worldwide transportation network. At the root of many of the advances over the preceding 50 years was the National Aeronautics and Space Administration (NASA). On October 1, 1958, just a few weeks before the flight of that Pan Am 707, NASA came into existence. Tasked with establishing a national space program as part of a Cold War competition between the United States and the Soviet Union, NASA is often remembered in popular memory first for putting the first human beings on the Moon in July 1969, followed by running the successful 30-year Space Shuttle Program and by landing the Rover Curiosity on Mars in August 2012. What many people do not recognize is the crucial role the first 'A' in NASA played in the development of aircraft since the Agency's inception. Innovations shaping the aerodynamic design, efficient operation, and overall safety of aircraft made NASA a vital element of the American aviation industry even though they remained unknown to the public. This is the story of one facet of NASA's many contributions to commercial, military, and general aviation: the development of aircraft propulsion technology, which provides the power for flight.

Kinney, Jeremy R.↗
NASA NTRS1972

Space shuttle: Static stability and control investigation of NR/GD delta wing booster (B-20) and delta wing orbiter (134D), volume 1

Experimental aerodynamic investigations have been made on a .0035 scale model North American Rockwell/General Dynamics version of the space shuttle. Static stability and control data were obtained on the delta wing booster alone (B-20) and with the delta wing orbiter (134D) mounted in various positions on the booster. Six component aerodynamic force and moment data were recorded over an angle of attack range from -10 deg to 24 deg at 0 deg and 6 deg sideslip angles and from -10 deg to +10 deg sideslip at 0 deg angle of attack. Mach number ranged from 0.6 to 4.96.

Allen, E. C.↗
NASA NTRS1972

Space shuttle: Static stability and control investigation of NR/GD delta wing booster (B-20) and delta wing orbiter (134-D), volume 3

Experimental aerodynamic investigations have been made on a .0035 scale model North American Rockwell/General Dynamics version of the space shuttle in the NASA/MSFC 14 x 14 Inch Trisonic Wind Tunnel. Static stability and control data were obtained on the delta wing booster alone (B-20) and with the delta wing orbiter (134D) mounted in various positions on the booster. Six component aerodynamic force and moment data were recorded over an angle of attack range from -10 to 24 deg at 0 and 6 deg sideslip angles and from -10 to +10 deg sideslip at 0 deg angle of attack. Mach number ranged from 0.6 to 4.96.

Allen, E. C., Jr.↗
NASA NTRS1976

On the nature of the anti-tail of Comet Kohoutek /1973f/. II - Comparison of the working model with ground-based photographic observations

On the basis of photographic observations made at the Cerro Tololo Inter-American Observatory, the radial and transverse brightness profiles and time variations in the surface brightness of the anti-tail of Comet Kohoutek were examined. In the process of photometric reduction one-dimensional radial tracings passing through the comet's nucleus and covering the entire anti-tail were used in the place of the standard two-dimensional scans. Each radial scan was defined by the position angle, and 'noise' variations were interpolated from the known field brightness outside the anti-tail. An analysis of the results provides quantitative support for a previously proposed model (Sekanina, 1974) suggesting that the dust particles in the anti-tail suffered a significant loss in radius due to evaporation near the perihelion passage. Preliminary calculations indicate that only particles initially larger than 100-150 micrometers in diameter survived. The emission rate of dust may be comparable to those derived for Comets Arend-Roland (1957 III) and Bennett (1970 II).

Sekanina, Z.↗
NASA NTRS1983

The structure of Neptune's upper atmosphere - The stellar occultation of 24 May 1981

Observations of the 24 May 1981 occulation of an uncatalogued star by Neptune made at the Cerro Tololo Inter-American Observatory have been analyzed to yield temperature profiles of Neptune's upper atmosphere for number densities near 5 x 10 to the 13th per cu cm. The mean temperatures at immersion (latitude - 56 deg) and emersion (latitude - 16 deg) obtained by numerical inversion were 140 + or - 10 K and 154 + or - 10 K, respectively. The immersion and emersion profiles are remarkably similar in overall shape, suggestive of global atmospheric layering. From the astrometry of the event, precise relative positions of Neptune and the occulted star were obtained.

French, R. G.↗
NASA NTRS1958

Transonic-Wind-Tunnel Tests of the Aerodynamic Characteristics of a 0.15-Scale Model of the North American Aviation 255-Inch Fin-Stabilized External Store, Coord No. AF-AM-4

An investigation has been made in the Langley 8-foot transonic tunnels on the aerodynamic characteristics of a 0.15-scale model of the North American Aviation 255-inch fin-stabilized external store over a maximum Mach number range of 0.60 to 1.2 and on the effects of mounting lugs, of fin orientation, of fin aspect ratio, and of fixed-transition. The Reynolds number (based on a body length of 37.50 inches) varied from 9.8 x 10(exp 6) to 13.1 x 10(exp 6). The results indicate that the static margin of the finned store at low lift coefficients was only 9 percent of body length at subsonic Mach numbers and was reduced to zero at a Mach number of 1.0, Increasing the fin aspect ratio from 1.82 to 2.41 increased the subsonic static margin to 18 percent and provided a minimum margin of 9 percent near a Mach number of l.O. Store mounting lugs or fin orientation had only small effects on the aerodynamic characteristics of the basic store.

Fischetti, Thomas L.↗
NASA NTRS1982

Perspectives in remote sensing in Brazil. An approach of the remote sensing applications to Earth resources surveys

Since the systematic use of earth surface data collection by orbital sensor systems started in 1972 with the launching of the North American LANDSAT satellite, a great effort has been made to assimilate, develop and transfer remote sensing technology (data acquisition and analysis) in its many applications in Brazil. The availability of sensor systems and existing data is considered approached, as well as those which will soon be available to the Brazilian researchers. The new systems of the LANDSAT-4, of the Columbia space shuttle and of the French satellites of the SPOT series are discussed. Some characteristics of the sensor system for the first Brazilian remote sensing satellite, to be launched by the end of the decade, are presented. Some LANDSAT-4 and SPOT simulation products are shown, emphasizing how the data obtained by these new satellites can be applied.

Parada, N. D. J.↗
NASA NTRS1960

Investigation of the Subsonic Stability and Control Characteristics of a 1/7-Scale Model of the North American X-15 Airplane with and without Fuselage Forebody Strakes

An investigation of the low-subsonic stability and control characteristics of a l/7-scale free-flying model modified to represent closely the North American X-15 airplane (configuration 3) has been made in the Langley full-scale tunnel. Flight conditions at a relatively low altitude were simulated with the center of gravity at 16.0 percent of the mean aerodynamic chord. The longitudinal stability and control were considered to be satisfactory for all flight conditions tested. The lateral flight behavior was generally satisfactory for angles of attack below about 20 deg. At higher angles, however, the model developed a tendency to fly in a side-slipped attitude because of static directional instability at small sideslip angles. Good roll control was maintained to the highest angles tested, but rudder effectiveness diminished with increasing angle of attack and became adverse for angles above 40 deg. Removal of the lower rudder had little effect on the lateral flight characteristics for angles of attack less than about 20 deg but caused the lateral flight behavior to become worse in the high angle-of-attack range. The addition of small fuselage forebody strakes improved the static directional stability and lateral flight behavior of both configurations.

Hassell, James L., Jr.↗