Results for “Analytical fabric model” — Page 2

NASA NTRS2008

A Computational Approach for Model Update of an LS-DYNA Energy Absorbing Cell

NASA and its contractors are working on structural concepts for absorbing impact energy of aerospace vehicles. Recently, concepts in the form of multi-cell honeycomb-like structures designed to crush under load have been investigated for both space and aeronautics applications. Efforts to understand these concepts are progressing from tests of individual cells to tests of systems with hundreds of cells. Because of fabrication irregularities, geometry irregularities, and material properties uncertainties, the problem of reconciling analytical models, in particular LS-DYNA models, with experimental data is a challenge. A first look at the correlation results between single cell load/deflection data with LS-DYNA predictions showed problems which prompted additional work in this area. This paper describes a computational approach that uses analysis of variance, deterministic sampling techniques, response surface modeling, and genetic optimization to reconcile test with analysis results. Analysis of variance provides a screening technique for selection of critical parameters used when reconciling test with analysis. In this study, complete ignorance of the parameter distribution is assumed and, therefore, the value of any parameter within the range that is computed using the optimization procedure is considered to be equally likely. Mean values from tests are matched against LS-DYNA solutions by minimizing the square error using a genetic optimization. The paper presents the computational methodology along with results obtained using this approach.

Horta, Lucas G.↗

NASA NTRS1985

Automatic Processing of Reactive Polymers

A series of process modeling computer codes were examined. The codes use finite element techniques to determine the time-dependent process parameters operative during nonisothermal reactive flows such as can occur in reaction injection molding or composites fabrication. The use of these analytical codes to perform experimental control functions is examined; since the models can determine the state of all variables everywhere in the system, they can be used in a manner similar to currently available experimental probes. A small but well instrumented reaction vessel in which fiber-reinforced plaques are cured using computer control and data acquisition was used. The finite element codes were also extended to treat this particular process.

Roylance, D.↗

NASA NTRS1972

Study of blade clearance effects on centrifugal pumps

A program of analysis, design, fabrication, and testing has been conducted to develop and experimentally verify analytical models to predict the effects of impeller blade clearance on centrifugal pumps. The effect of tip clearance on pump efficiency, and the relationship between the head coefficient and torque loss with tip clearance was established. Analysis were performed to determine the cost variation in design, manufacture, and test that would occur between unshrouded and shrouded impellers. An impeller, representative of typical rocket engine impellers, was modified by removing its front shroud to permit variation of its blade clearances. It was tested in water with special instrumentation to provide measurements of blade surface pressures during operation. Pump performance data were obtained from tests at various impeller tip clearances. Blade pressure data were obtained at the nominal tip clearance. Comparisons of predicted and measured data are given.

Hoshide, R. K.↗

NASA NTRS1991

Characterization and modeling of an advanced flexible thermal protection material for space applications

This paper describes experimental and analytical characterization of a new flexible thermal protection material known as Tailorable Advanced Blanket Insulation (TABI). This material utilizes a three-dimensional ceramic fabric core structure and an insulation filler. TABI is the leading candidate for use in deployable aeroassisted vehicle designs. Such designs require extensive structural modeling, and the most significant in-plane material properties necessary for model development are measured and analytically verified in this study. Unique test methods are developed for damping measurements. Mathematical models are developed for verification of the experimental modulus and damping data, and finally, transverse properties are described in terms of the inplane properties through use of a 12-dof finite difference model of a simple TABI configuration.

Clayton, Joseph P.↗

NASA NTRS1988

Advanced composite materials for precision segmented reflectors

The objective in the NASA Precision Segmented Reflector (PSR) project is to develop new composite material concepts for highly stable and durable reflectors with precision surfaces. The project focuses on alternate material concepts such as the development of new low coefficient of thermal expansion resins as matrices for graphite fiber reinforced composites, quartz fiber reinforced epoxies, and graphite reinforced glass. Low residual stress fabrication methods will be developed. When coupon specimens of these new material concepts have demonstrated the required surface accuracies and resistance to thermal distortion and microcracking, reflector panels will be fabricated and tested in simulated space environments. An important part of the program is the analytical modeling of environmental stability of these new composite materials concepts through constitutive equation development, modeling of microdamage in the composite matrix, and prediction of long term stability (including viscoelasticity). These analyses include both closed form and finite element solutions at the micro and macro levels.

Stein, Bland A.↗

NASA NTRS1990

Structural considerations for fabrication and mounting of the AXAF HRMA optics

A methodology is described which minimizes optics distortion in the fabrication, metrology, and launch configuration phases. The significance of finite element modeling and breadboard testing is described with respect to performance analyses of support structures and material effects in NASA's AXAF X-ray optics. The paper outlines the requirements for AXAF performance, optical fabrication, metrology, and glass support fixtures, as well as the specifications for mirror sensitivity and the high-resolution mirror assembly. Analytical modeling of the tools is shown to coincide with grinding and polishing experiments, and is useful for designing large-area polishing and grinding tools. Metrological subcomponents that have undergone initial testing show evidence of meeting force requirements.

Cohen, Lester M.↗

NASA NTRS1995

Graphite fiber textile preform/copper matrix composites

Graphite fiber reinforced/copper matrix composites have sufficiently high thermal conduction to make them candidate materials for critical heat transmitting and rejection components. The term textile composites arises because the preform is braided from fiber tows, conferring three-dimensional reinforcement and near net shape. The principal issues investigated in the past two years have centered on developing methods to characterize the preform and fabricated composite and on braidability. It is necessary to have an analytic structural description for both processing and final property modeling. The structure of the true 3-D braids used is complex and has required considerable effort to model. A structural mapping has been developed as a foundation for analytic models for thermal conduction and mechanical properties. The conductivity has contributions both from the copper and the reinforcement. The latter is accomplished by graphitization of the fibers, the higher the amount of graphitization the greater the conduction. This is accompanied by an increase in the fiber modulus, which is desirable from a stiffness point of view but decreases the braidability; the highest conductivity fibers are simply too brittle to be braided. Considerable effort has been expended on determining the optimal braidability--conductivity region. While a number of preforms have been fabricated, one other complication intervenes; graphite and copper are immiscible, resulting in a poor mechanical bond and difficulties in infiltration by molten copper. The approach taken is to utilize a proprietary fiber coating process developed by TRA, of Salt Lake City, Utah, which forms an itermediary bond. A number of preforms have been fabricated from a variety of fiber types and two sets of these have been infiltrated with OFHC copper, one with the TRA coating and one without. Mechanical tests have been performed using a small-scale specimen method and show the coated specimens to have superior mechanical properties. Final batches of preforms, including a finned, near net shape tube, are being fabricated and will be infiltrated before summer.

Gilatovs, G. J.↗

NASA NTRS1993

Design of power electronics for TVC EMA systems

The Composite Development Division of the Propulsion Laboratory at Marshall Space Flight Center (MSFC) is currently developing a class of electromechanical actuators (EMA's) for use in space transportation applications such as thrust vector control (TVC) and propellant control valves (PCV). These high power servomechanisms will require rugged, reliable, and compact power electronic modules capable of modulating several hundred amperes of current at up to 270 volts. MSFC has selected the brushless dc motor for implementation in EMA's. This report presents the results of an investigation into the applicability of two new technologies, MOS-controlled thyristors (MCT's) and pulse density modulation (PDM), to the control of brushless dc motors in EMA systems. MCT's are new power semiconductor devices, which combine the high voltage and current capabilities of conventional thyristors and the low gate drive requirements of metal oxide semiconductor field effect transistors (MOSFET's). The commanded signals in a PDM system are synthesized using a series of sinusoidal pulses instead of a series of square pulses as in a pulse width modulation (PWM) system. A resonant dc link inverter is employed to generate the sinusoidal pulses in the PDM system. This inverter permits zero-voltage switching of all semiconductors which reduces switching losses and switching stresses. The objectives of this project are to develop and validate an analytical model of the MCT device when used in high power motor control applications and to design, fabricate, and test a prototype electronic circuit employing both MCT and PDM technology for controlling a brushless dc motor.

Nelms, R. Mark↗

NASA NTRSDate not supplied

Determining the Cause of Reduced Concurrent Flame Spread over Thin Solid Fuels in Low Pressure and Low Gravity

The spread of flames over the surface of solid combustible materials is affected by the environmental conditions. Variables such as flow velocity, oxygen concentration, ambient pressure, partial gravity or microgravity, may change the material flammability and influence the fire dynamics. This is an important fire safety issue for space exploration vehicles and space habitats which will very likely have different environments than those currently used on the International Space Station, such as reduced pressure and enriched oxygen concentration (SEA). However, testing experimentally the materials to be used and qualified for space exploration under these conditions is a difficult and expensive task. Here, numerical modeling is used to understand the dominant physico-chemical processes on the concurrent flame spread over thin fabrics under reduced ambient pressure (and in turn, buoyancy) and variable gravitational conditions. The numerical model uses the Fire Dynamics Simulator (FDS6) code with a single-step Arrhenius reaction rate for the solid phase decomposition. Different models are tested for the gas phase combustion kinetics. The model results are validated with experimental results obtained at similar reduced ambient pressure and flow conditions at 1 g. It is shown that as ambient pressure is reduced the flame spread rate over a thin fabric is also reduced, both experimentally and numerically. Numerical results are compared to an analytical approach previously developed to explain the experimental trends. Further interpretation of the model results provides information regarding the physics of the process and how they are affected by the lower pressure environments and gravity conditions. The results of this work provide guidance for potential on-earth testing for fire safety design in spacecraft and space habitats.

Fire Safety↗

NASA NTRSDate not supplied

Determining the Cause of Reduced Concurrent Flame Spread over Thin Solid Fuels in Low Pressure and Low Gravity

The spread of flames over the surface of solid combustible materials is affected by the environmental conditions. Variables such as flow velocity, oxygen concentration, ambient pressure, partial gravity or microgravity, may change the material flammability and influence the fire dynamics. This is an important fire safety issue for space exploration vehicles and space habitats which will very likely have different environments than those currently used on the International Space Station, such as reduced pressure and enriched oxygen concentration (SEA). However, testing experimentally the materials to be used and qualified for space exploration under these conditions is a difficult and expensive task. Here, numerical modeling is used to understand the dominant physico-chemical processes on the concurrent flame spread over thin fabrics under reduced ambient pressure (and in turn, buoyancy) and variable gravitational conditions. The numerical model uses the Fire Dynamics Simulator (FDS6) code with a single-step Arrhenius reaction rate for the solid phase decomposition. Different models are tested for the gas phase combustion kinetics. The model results are validated with experimental results obtained at similar reduced ambient pressure and flow conditions at 1 g. It is shown that as ambient pressure is reduced the flame spread rate over a thin fabric is also reduced, both experimentally and numerically. Numerical results are compared to an analytical approach previously developed to explain the experimental trends. Further interpretation of the model results provides information regarding the physics of the process and how they are affected by the lower pressure environments and gravity conditions. The results of this work provide guidance for potential on-earth testing for fire safety design in spacecraft and space habitats.

microgravity↗

NASA NTRS1991

Transpiration cooled throat for hydrocarbon rocket engines

The objective for the Transpiration Cooled Throat for Hydrocarbon Rocket Engines Program was to characterize the use of hydrocarbon fuels as transpiration coolants for rocket nozzle throats. The hydrocarbon fuels investigated in this program were RP-1 and methane. To adequately characterize the above transpiration coolants, a program was planned which would (1) predict engine system performance and life enhancements due to transpiration cooling of the throat region using analytical models, anchored with available data; (2) a versatile transpiration cooled subscale rocket thrust chamber was designed and fabricated; (3) the subscale thrust chamber was tested over a limited range of conditions, e.g., coolant type, chamber pressure, transpiration cooled length, and coolant flow rate; and (4) detailed data analyses were conducted to determine the relationship between the key performance and life enhancement variables.

May, Lee R.↗

NASA NTRS1973

Investigation of Vibrational Energy Transfer in Connected Structures

The results are reported of an analytical and experimental investigation on the vibrational energy transfer between connected substructures under random excitation. In the analytical area, the basic foundation and assumptions of the statistical energy analysis (SEA) method, a major tool in random response analysis of structures, were examined and reviewed. A new SEA formulation based on the strong coupling condition of the substructures was carried out and presented. Also presented were the results of vibration energy transfer study based on the wave equations applied to connected structures. In the experimental phase, three simple structural models were fabricated and tested. Additional tests were performed on selected substructures which formed parts of the test models. The test results were presented and evaluated against the analytical data.

Hwang, C.↗

NASA NTRS1981

Experimental and analytical studies of advanced air cushion landing systems

Several concepts are developed for air cushion landing systems (ACLS) which have the potential for improving performance characteristics (roll stiffness, heave damping, and trunk flutter), and reducing fabrication cost and complexity. After an initial screening, the following five concepts were evaluated in detail: damped trunk, filled trunk, compartmented trunk, segmented trunk, and roll feedback control. The evaluation was based on tests performed on scale models. An ACLS dynamic simulation developed earlier is updated so that it can be used to predict the performance of full-scale ACLS incorporating these refinements. The simulation was validated through scale-model tests. A full-scale ACLS based on the segmented trunk concept was fabricated and installed on the NASA ACLS test vehicle, where it is used to support advanced system development. A geometrically-scaled model (one third full scale) of the NASA test vehicle was fabricated and tested. This model, evaluated by means of a series of static and dynamic tests, is used to investigate scaling relationships between reduced and full-scale models. The analytical model developed earlier is applied to simulate both the one third scale and the full scale response.

Lee, E. G. S.↗

NASA NTRS1984

Atmosphere behavior in gas-closed mouse-algal systems - An experimental and modelling study

A NASA-sponsored research program initiated using mathematical modelling and laboratory experimentation aimed at examining the gas-exchange characteristics of artificial animal/plant systems closed to the ambient atmosphere is studied. The development of control techniques and management strategies for maintaining the atmospheric levels of carbon dioxide and oxygen at physiological levels is considered. A mathematical model simulating the behavior of a gas-closed mouse-algal system under varying environmental conditions is described. To verify and validate the model simulations, an analytical system with which algal growth and gas exchange characteristics can be manipulated and measured is designed, fabricated, and tested. The preliminary results are presented.

Averner, M. M.↗

NASA NTRS2004

NASA's Integrated Development of Solar Sail Propulsion Project

Solar sails have been studied for a variety of missions and have the potential to provide cost effective, propellantless propulsion that enables longer on-station operation, increased scientific payload mass fraction, and access to previously inaccessible orbits (e. g., non-Keplerian, high solar latitudes, etc.). Research being conducted by the In-Space Propulsion (ISP) Technologies Projects is at the forefront of NASA's efforts to mature propulsion technologies that will enable or enhance a variety of space science missions. Solar sail propulsion systems will be required to meet the challenge of monitoring and predicting space weather by the Office of Space Science's (OSS) Living with a Star (LWS) program. Near-to-mid-term mission needs include monitoring of solar activity and observations at high solar latitudes. Work currently funded by the ISP s Solar Sail Propulsion (SSP) project is based on the quantitative demonstration of scalability of present solar sail subsystem designs and concepts to future mission requirements through ground testing of hardware, computational modeling and analytical simulations. This paper will give an overview of the Solar Sail Propulsion project's major development tasks of fabricating and testing two different subscale (400 square meter sail) solar sail system architectures. It will then be shown how either of these subscale prototypes can evolve into a flight validation system and briefly discuss the mission parameter. The paper will conclude with a discussion on how a flight validation will exercise the quantitative tools needed to demonstrate the scale to the size needed for the Solar Polar Imager and L1-Diamond SEC roadmap missions.

Garbe, Gregory↗

NASA NTRS1985

WRAP-RIB antenna technology development

The wrap-rib deployable antenna concept development is based on a combination of hardware development and testing along with extensive supporting analysis. The proof-of-concept hardware models are large in size so they will address the same basic problems associated with the design fabrication, assembly and test as the full-scale systems which were selected to be 100 meters at the beginning of the program. The hardware evaluation program consists of functional performance tests, design verification tests and analytical model verification tests. Functional testing consists of kinematic deployment, mesh management and verification of mechanical packaging efficiencies. Design verification consists of rib contour precision measurement, rib cross-section variation evaluation, rib materials characterizations and manufacturing imperfections assessment. Analytical model verification and refinement include mesh stiffness measurement, rib static and dynamic testing, mass measurement, and rib cross-section characterization. This concept was considered for a number of potential applications that include mobile communications, VLBI, and aircraft surveillance. In fact, baseline system configurations were developed by JPL, using the appropriate wrap-rib antenna, for all three classes of applications.

Freeland, R. E.↗

NASA NTRSDate not supplied

Classification of Notices to Airmen using Natural Language Processing

This paper establishes the feasibility of using Natural Language Processing (NLP) to classify NOTAMs or Notices to Airmen – a pilot messaging framework to gather real-time situational awareness. Present day air mobility operations heavily rely on NOTAMs. However, pilots often have difficulty interpreting NOTAMs due to the sheer volume of inapplicable messages and unclear abbreviations. Using NLP, the presented study analyzes the accuracy of classifying NOTAMs and, thereby, the efficiency of generating actionable interpretations in real time. To this effect, efficacies of four NLP neural network architectures were analyzed, including three Recurrent Neural Networks (RNNs) with GloVe, Word2Vec, and FastText word embeddings, and one trained Bi-Directional Encoder Representations from Transformers (BERT) model. The four neural networks were trained and evaluated on three open-source datasets of varying text lengths, vocabularies, and grammars, taken from e-commerce product descriptions, social media tweets, and unstructured descriptions for data and analytics services on open data marketplaces such as NASA’s Data and Reasoning Fabric (DRF) platform. This provided cross-analysis of each neural network architecture’s performance per text type. The best performing architecture, BERT, was then fine-tuned on a collection of open-source NOTAM data. Post-training, a real-time NOTAM classification service was implemented to draw inference on new NOTAMs using the trained model, which demonstrated close to 99% accuracy in classification. This modular classification service is envisioned to be integrated with a data and analytics delivery platform, such as the DRF, thus availing real-time contextualization of NOTAMs to air mobility clients, humans, and machines for enhanced decision making.

Aiden C. Szeto↗

NASA NTRSDate not supplied

Classification of Notices to Airmen using Natural Language Processing

This paper establishes the feasibility of using Natural Language Processing (NLP) to classify NOTAMs or Notices to Airmen – a pilot messaging framework to gather real-time situational awareness. Present day air mobility operations heavily rely on NOTAMs. However, pilots often have difficulty interpreting NOTAMs due to the sheer volume of inapplicable messages and unclear abbreviations. Using NLP, the presented study analyzes the accuracy of classifying NOTAMs and, thereby, the efficiency of generating actionable interpretations in real time. To this effect, efficacies of four NLP neural network architectures were analyzed, including three Recurrent Neural Networks (RNNs) with GloVe, Word2Vec, and FastText word embeddings, and one trained Bi-Directional Encoder Representations from Transformers (BERT) model. The four neural networks were trained and evaluated on three open-source datasets of varying text lengths, vocabularies, and grammars, taken from e-commerce product descriptions, social media tweets, and unstructured descriptions for data and analytics services on open data marketplaces such as NASA’s Data and Reasoning Fabric (DRF) platform. This provided cross-analysis of each neural network architecture’s performance per text type. The best performing architecture, BERT, was then fine-tuned on a collection of open-source NOTAM data. Post-training, a real-time NOTAM classification service was implemented to draw inference on new NOTAMs using the trained model, which demonstrated close to 99% accuracy in classification. This modular classification service is envisioned to be integrated with a data and analytics delivery platform, such as the DRF, thus availing real-time contextualization of NOTAMs to air mobility clients, humans, and machines for enhanced decision making.

Aiden Szeto↗