Search NASA⌕ Search

SEARCH · Search NASA

Results for “Approach Plate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Transient-forced convection film boiling on an isothermal flat plate

An approach for the solution of transient-forced convection film boiling on an isothermal flat plate using the boundary layer model is developed. The similarity variables are used to convert the governing partial differential equations to ordinary ones. The results of numerical solutions of these ordinary equations indicate that the transient process can be classified as one-dimensional conduction, intermediate, and the steady state regions. The time required for the one-dimensional conduction and the time necessary to attain a steady state condition are obtained. The influence of interfacial shear is seen to be negligible while the Prandtl Number and the ratio (C sub p delta T divided by h sub fg times Pr) have major influence. The use of local similarity approximations for the intermediate regime facilitates prediction of complete boundary layer growth. Using the ratio of time at any instant to the steady state time as abscissa, the curves representing the boundary layer growth can be merged into a single mean curve within 5 percent. Further, the analysis shows that the average rate of heat transfer during transient is 50 to 100 percent higher than those at steady state. The average rate of vapor convected away is 10 to 15 percent lower than at steady state while the average rate of accumulation to form the vapor layer is 1 to 14 times larger. Further, the total heat transferred during transient increases and the evaporation decreases for increasing values of C sub p delta T divided by h sub fg times Pr

Nagendra, H. R.↗
NASA NTRS1992

The linear stability of a flat plate boundary-layer approaching a cylindrical obstacle

The linear stability of the low-speed three-dimensional flow over a flat plate with an attached cylinder is studied. The region of interest is upstream of the initial separation point and includes the effects of both adverse and favorable pressure gradients, as well as crossflow. The resulting boundary-layer is subject to both the Tollmien-Schlichting (TS) and crossflow instabilities. Linear stability calculations, using N-factor correlations, indicate that the transition process would be dominated by TS instabilities, although for low frequencies crossflow-type disturbances are important.

Spall, R. E.↗
NASA NTRS1974

Solar-energy absorber: Active infrared (IR) trap

Efficiency of solar-energy absorbers may be improved to 95% by actively cooling their intermediate glass plates. This approach may be of interest to manufacturers of solar absorbers and to engineers and scientists developing new sources of energy.

Brantley, L. W., Jr.↗
NASA NTRS1986

A new approach to large area microchannel plate manufacture

Methods of manufacture of twisted single elements as the base for producing microchannel plates (MCP) are discussed. Initial evaluations validated the off-axis channel concept and no technological roadblocks were identified which would prevent fabrication of high gain, high spatial resolution, large format MCP's using this technique. The first MP's have operated at stable gains of 3 million with pulse height resolution superior to results obtained by standard chevron MCP's.

Source record↗
NASA NTRS1995

Cell shape, cytoskeletal mechanics, and cell cycle control in angiogenesis

Capillary endothelial cells can be switched between growth and differentiation by altering cell-extracellular matrix interactions and thereby, modulating cell shape. Studies were carried out to determine when cell shape exerts its growth-regulatory influence during cell cycle progression and to explore the role of cytoskeletal structure and mechanics in this control mechanism. When G0-synchronized cells were cultured in basic fibroblast growth factor (FGF)-containing defined medium on dishes coated with increasing densities of fibronectin or a synthetic integrin ligand (RGD-containing peptide), cell spreading, nuclear extension, and DNA synthesis all increased in parallel. To determine the minimum time cells must be adherent and spread on extracellular matrix (ECM) to gain entry into S phase, cells were removed with trypsin or induced to retract using cytochalasin D at different times after plating. Both approaches revealed that cells must remain extended for approximately 12-15 h and hence, most of G1, in order to enter S phase. After this restriction point was passed, normally 'anchorage-dependent' endothelial cells turned on DNA synthesis even when round and in suspension. The importance of actin-containing microfilaments in shape-dependent growth control was confirmed by culturing cells in the presence of cytochalasin D (25-1000 ng ml-1): dose-dependent inhibition of cell spreading, nuclear extension, and DNA synthesis resulted. In contrast, induction of microtubule disassembly using nocodazole had little effect on cell or nuclear spreading and only partially inhibited DNA synthesis. Interestingly, combination of nocodazole with a suboptimal dose of cytochalasin D (100 ng ml-1) resulted in potent inhibition of both spreading and growth, suggesting that microtubules are redundant structural elements which can provide critical load-bearing functions when microfilaments are partially compromised. Similar synergism between nocodazole and cytochalasin D was observed when cytoskeletal stiffness was measured directly in living cells using magnetic twisting cytometry. These results emphasize the importance of matrix-dependent changes in cell and nuclear shape as well as higher order structural interactions between different cytoskeletal filament systems for control of capillary cell growth during angiogenesis.

Non-NASA Center↗
NASA NTRS2023

Procedure Automation Rating Matrix

The National Aeronautics and Space Administration (NASA) Advanced Air Mobility (AAM) National Campaign (NC) is researching the means by which future Urban Air Mobility (UAM) aircraft will operate safely in an integrated and scalable airspace architecture. Consistent with this objective, the NASA NC Airspace Procedures team designed a matrix to evaluate UAM instrument flight procedure design, flyability and interoperability of candidate departure, enroute, and approach architectures in live flight or simulation. The Procedure Automation Rating Matrix (PARM) is a multi-dimensional rating scale designed to provide direct feedback from test pilots and operators to airspace procedure designers developing airspace constructs for the integration and scalability of AAM operations in the National Airspace System (NAS). The PARM is assessed using a hierarchical decision tree that guides the operator through a ten-point alpha-numeric rating scale initiated either with or without the use of automation.

National Campaign↗
NASA NTRS1995

Assessment of computational models for thermoelectroelastic multilayered plates

A study is made of the accuracy of the steady-state (static) thermoelectroelastic response of multilayered hybrid composite plates predicted by five modeling approaches, based on two-dimensional plate theories. The plates consist of a combination of fiber-reinforced and piezothermoelastic layers. The standard of comparison is taken to be the exact three-dimensional thermoelectroelastic solutions, and the quantities compared include gross response characteristics (e.g., strain energy components, and average through-the-thickness displacements); detailed, through-the-thickness distributions of displacements and stresses; and sensitivity coefficients of the response quantities (derivatives of the response quantities with respect to material parameters of the plate). The modeling approaches considered include first-order theory; third-order theory; discrete-layer theory (with piecewise linear variation of the in-plane displacements, temperature and electric potential, in the thickness direction); and two predictor-corrector procedures.

Tang, Yvette T.↗
NASA NTRS1989

Assessment of shear deformation theories for multilayered composite plates

A review is made of the different approaches used for modeling multilayered composite plates. Discussion focuses on different approaches for developing two-dimensional shear deformation theories; classification of two-dimensional theories based on introducing plausible displacement, strain and/or stress assumptions in the thickness direction; and first-order shear deformation theories based on linear displacement assumptions in the thickness coordinate. Extensive numerical results are presented showing the effects of variation in the lamination and geometric parameters of simply supported composite plates on the accuracy of the static and vibrational responses predicted by six different modeling approaches (based on two-dimensional shear deformation theories). The standard of comparison is taken to be the exact three-dimensional elasticity solutions. Some of the future directions for research on the modeling of multilayered composite plates are outlined.

Noor, Ahmed K.↗
NASA NTRS1972

Study of effects of design details on structural response to acoustic excitation

The normal mode vibration characteristics of one-dimensional and two-dimensional panel arrays were investigated analytically and experimentally. The finite element displacement method was used to formulate the structural models. The structural models include a stiffness and consistent mass matrix for thin-walled open-section beams not previously reported, and a modification of a rectangular plate bending element to include a fundamental interior mode for the element as a generalized coordinate. Provision for adding lumped masses to represent accelerometers is also included. For the one-dimensional panel, the normal mode stress resultants are obtained by integrating the equilibrium equations directly. For the two-dimensional panel arrays, the solution for the stress resultants in the cover sheet was attempted by introducing stress functions dependent upon the displacement field of the plate element. This approach, although incomplete, is a natural extension of the one-dimensional analysis for plate elements. The exerimental program which was used to verify the analysis is described and experimental results are compared with the analysis.

Rudder, F. F., Jr.↗
NASA NTRS1976

Aeroheating model advancements featuring electroless metallic plating

Discussed are advancements in wind tunnel model construction methods and hypersonic test data demonstrating the methods. The general objective was to develop model fabrication methods for improved heat transfer measuring capability at less model cost. A plated slab model approach was evaluated with cast models containing constantan wires that formed single-wire-to-plate surface thermocouple junctions with a seamless skin of electroless nickel alloy. The surface of a space shuttle orbiter model was selectively plated with scaled tiles to simulate, with high fidelity, the probable misalignments of the heatshield tiles on a flight vehicle. Initial, Mach 8 heating results indicated a minor effect of tile misalignment roughness on boundary layer transition, implying a possible relaxation of heatshield manufacturing tolerances. Some loss of the plated tiles was experienced when the model was tested at high heating rates.

Stalmach, C. J., Jr.↗
NASA NTRS1990

Modeling of composite beams and plates for static and dynamic analysis

A rigorous theory and corresponding computational algorithms was developed for a variety of problems regarding the analysis of composite beams and plates. The modeling approach is intended to be applicable to both static and dynamic analysis of generally anisotropic, nonhomogeneous beams and plates. Development of a theory for analysis of the local deformation of plates was the major focus. Some work was performed on global deformation of beams. Because of the strong parallel between beams and plates, the two were treated together as thin bodies, especially in cases where it will clarify the meaning of certain terminology and the motivation behind certain mathematical operations.

Hodges, Dewey H.↗
NASA NTRS1973

Flat-plate collector performance evaluation. The case for a solar simulation approach

A method is proposed for determining the performance of flat-plate solar collector using a simulated sun. Collector test variables that will help establish the basis for the indoor test facility at the Lewis Research Center are discussed. The use of the indoor testing should permit a standard test for the convenient and accurate determination of collector performance. Preliminary test results are reported as an example of the type of collector performance data to be expected from the simulation approach.

Simon, F. F.↗
NASA NTRS1993

Ionospheric plasma flow about a system of electrically biased flat plates

The steady state interaction of two electrically biased parallel plates immersed in a flowing plasma characteristic of low earth orbit is studied numerically. Fluid equations are developed to describe the motion of the cold positively charged plasma ions, and are solved using finite-differences in two dimensions on a Cartesian grid. The behavior of the plasma electrons is assumed to be described by the Maxwell-Boltzmann distribution. Results are compared to an analytical and a particle simulation technique for a simplified flow geometry consisting of a single semi-infinite negatively biased plate. Comparison of the extent of the electrical disturbance into the flowing plasma and the magnitude of the current collected by the plate is very good. The interaction of two equally biased parallel plates is studied as a function of applied potential. The separation distance at which the current collected by either plate decreases by five and twenty percent is determined as a function of applied potential. The percent decreases were based on a non-interacting case. The decrease in overall current is caused by a decrease in ionic density in the region between the plates. As the separation between the plates decreases, the plates collect the ions at a faster rate than they are supplied to the middle region by the oncoming plasma flow. The docking of spacecraft in orbit is simulated by moving two plates of unequal potential toward one another in a quasi-static manner. One plate is held at a large negative potential while the other floats electrically in the resulting potential field. It is found that the floating plate does not charge continuously negative as it approaches the other more negatively biased plate. Instead, it charges more and then less negative as ionic current decreases and then increases respectively upon approach. When the two plates come into contact, it is expected that the electrically floating plate will charge rapidly negative to a potential near that of the other plate.

Herr, Joel L.↗
NASA NTRS1990

Thick plate bending wave transmission using a mobility power flow approach

The mobility power flow (MPF) approach is used in this paper to describe the flexural behavior of an L-shaped plate structure consisting of thick plates with rotary inertia and shear deformation effects included in the analysis. The introduction of the thick plate effects significantly increases the complexity of the structural mobility functions used in the definitions of the power flow terms; however, because of the substructuring that is used in the MPF approach, the complexity of the problem is significantly reduced as compared to solving for the global structure. Additionally, with the MPF approach the modal behavior is described. The MPF analysis of the L-shaped plate is performed for the case of point force excitation on one plate, with the two plates being identical in both size and thickness. The results of this analysis are compared to results from the finite-element analysis (FEA) and the statistical energy analysis (SEA) and show very good agreement in the low- and high-frequency regimes, respectively.

Mccollum, M. D.↗
NASA NTRS1972

An analytical solution for the squeeze film between a nondeformable sphere and groove

An analysis is presented to compute the film thickness, pressure and load relations between a rigid ball and rigid groove in normal approach when lubricated by a fluid with an exponential pressure-viscosity relationship. The geometry of the ball-groove system is reduced to the equivalent system of a paraboloid approaching a flat plate. Exact and approximate solutions are presented for the load and pressure relations. There is found to be a limiting load for a given geometry and lubricant regardless of the rate of approach.

Allen, C. W.↗
NASA NTRS1978

A graphical approach to the efficiency of flat-plate collectors

A nomogram is described which can be used to determine the thermal performance of flat plate solar collectors, resulting in two performance factors: the net absorptance and the net heat loss coefficient. The nomogram takes into account angle of incidence, collector slope, absorber plate design, insulating materials, thicknesses, optical properties of absorbing surfaces and glazing materials, and flow factors. A case example is given to illustrate the use of the nomogram.

Selcuk, M. K.↗
NASA NTRS1980

Green's function for a crack emanating from a circular hole in an infinite sheet

Stress-intensity factors, K/I/ and K/II/, are obtained for a point loaded crack emanating from a circular hole in an infinite plate. A series approach and the Muskhelishvili formulation in the two-dimensional theory of elasticity are used to derive the solution. The applicability of the solution is demonstrated by using it as a Green's function to obtain K/I/ and K/II/ and the case of (1) biaxial tension of an infinite plate and (2) bending of a wide strip.

Shivakumar, V.↗