Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOOSTER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fermilab Booster loss modelling and rebalancing using Bayesian methods

Fermilab Booster is being upgraded for the PIP-II project to support 20Hz ramp rate at higher intensities. Loss trip limits determine the achievable peak power. To meet PIP-II requirements, losses need to be halved as compared to current levels. Losses primarily occur at injection and transition crossing, with both gradually increasing and threshold-like intensity-dependent behaviors. The existing simulation models are not yet good enough for quantitative loss predictions. In practice, it will be necessary to tune up the Booster using iterative methods and operator intuition. In this paper we present an effort to systematically model Booster losses using active learning (Bayesian exploration) techniques, and subsequently to rebalance them for higher trip limit margins. We first created several sets of spatially and temporally isolated orbit and optics knobs, and trained Gaussian process models for each beam loss monitor as well as beam current. This is a complex task due to safety and timing requirements – we discuss mitigations such as uncertainty constraints and approximate fitting. Once models are stable, we perform large-scale single and multi-objective tuning using scalarized objectives made up of critical beam loss locations. Our results demonstrate significant rebalancing of losses, increasing trip margins, as well as an overall improvement in beam transmission efficiency. We are exploring how to combine existing simulations with experimental data and automate the collection procedure so that more advanced surrogate models can be created over time.

Kuklev, Nikita [Fermilab]↗
DOE OSTI2025

Design of a GammaT-Jump System for Fermilab Booster

A gammaT scheme may be required for the PIP-II era performance or ACE-MIRT era performance of the Booster. PIP-II era operations of the Fermilab proton complex will require the Fermilab Booster to increase beam intensity from 4.5e12 to 6.5e12 protons, while also increasing its ramp from 15 Hz to 20 Hz. These changes pose particular challenges for transition-crossing in the Booster, where longitudinal beam quality must be controlled in order to facilitate slip-stacking in the Recycler Ring later in the Main Injector cycle. Two novel gammaT jump schemes are proposed, termed double gammaT jump and partial gammaT jump, which optimizes the magnitude of the gammaT jump within optics and power supply constraints.

Eldred, Jeffrey Scott [Fermilab] (ORCID:0000000344↗
DOE OSTI2026

Design of a GammaT-Jump System for Fermilab Booster

A $\gamma_{T}$ scheme may be required for the PIP-II era performance or ACE-MIRT era performance of the Booster. PIP-II era operations of the Fermilab proton complex will require the Fermilab Booster to increase beam intensity from 4.5e12 to 6.7e12 protons, while also increasing its ramp from 15 Hz to 20 Hz. These changes pose particular challenges for transition-crossing in the Booster, where longitudinal beam quality must be controlled in order to facilitate slip-stacking in the Recycler Ring later in the Main Injector cycle. Two novel $\gamma_{T}$-jump schemes are proposed, termed Double $\gamma_{T}$ jump and Partial $\gamma_{T}$-jump , which optimize the magnitude of the $\gamma_{T}$-jump within optics and power supply constraints.

Eldred, J. [Fermilab] (ORCID:000000034432072X)↗
DOE OSTI2026

Magnetic Measurements of Fermilab Rapid-Cycling Booster Gradient Magnets

Fermilab is upgrading its Booster synchrotron to increase ramp rate and intensity. This is part of the Proton Improvement Plan (PIP-II) that will allow the Main Injector to achieve proton beam power of 1.2 MW within the next few years. This upgrade includes running the 55-year-old Booster magnets at 20 Hz instead of the usual 15 Hz, and construction of some shorter and wider aperture versions of these combined-function gradient magnets. Magnetic measurements were performed to characterize the present 15 Hz AC performance, and then again with 20 Hz ramp cycle to ensure performance and compatibility in this new operating regime. A 3 m-long curved flat-coil was developed for these measurements using Printed Circuit Board (PCB) technology. The probe also has a separate 0.5 m-long body-field probe, allowing integral, body, and end fields to be measured across 100 mm of the magnet aperture. The sampling rate for these measurements during the AC cycle was 200 kHz, and field resolution was better than 0.01%. Details of the probe, measurements, and results are presented.

DiMarco, J. [Fermilab] (ORCID:0000000228400036)↗
DOE OSTI2024

Electron cloud simulations in the Fermilab booster

As part of Fermilab's Proton Improvement Plan-II (PIP-II),the Fermilab Booster synchrotron will operate at a higherintensity, increasing from 4.5 x 10^12 to 6.7 x 10^12 protons per pulse (ppp). A potential challenge for achievinghigh intensity performance arises from rapid transverse instabilities induced by electron cloud (EC). This researchpresents EC simulations using PyECLOUD, which is anadvanced computational tool that incorporates measurements of the secondary electron yield (SEY) from theBooster's combined function magnet material. By systematically varying beam parameters in PyECLOUD, such asbunch structure, SEY, bunch length, and intensity, it becomes possible to forecast the impact of EC effects on thebeam stability of the PIP-II era Booster.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Fermilab Booster loss modelling and rebalancing using Bayesian methods

To meet PIP-II upgrade requirements, Fermilab Booster losses need to be reduced by 50% compared to present levels. So far, simulations are not good enough to predict loss patterns. Thus, an extensive Booster tune up will be necessary to achieve required performance. In this paper we present an effort to build a data-driven loss model using Bayesian techniques, and subsequently to rebalance losses for higher trip margins. We first created several sets of spatially and temporally isolated orbit and optics knobs, and trained Gaussian process models for each beam loss monitor as well as beam current. Novel techniques of uncertainty constraints and approximate GP fitting were introduced to handle safety and timing requirements. We then performed single and multi-objective tuning using scalarized objectives comprised of critical beam loss locations. We achieved significant rebalancing of losses, increasing margins by 25%, as well as an overall improvement in transmission efficiency of 0.4%. Automated data collection is being developed so that more accurate surrogate models can be trained over time.

Kuklev, N. [Fermilab]↗
DOE OSTI2024

Observation of a Synchro-Betatron Instability in Fermilab Booster

In preparation for PIP-II, there has been interest in running the Fermilab Booster at a higher current more indicative of the PIP-II era operation. In July 2023, an experiment was performed to study collective instabilities over the transition crossing at the Fermilab Booster. Over the transition crossing, the synchrotron tune becomes small and synchro-betatron instabilities become possible. During the experiment, an intensity threshold was observed, above which a dipole instability with losses concentrated in the tail of the bunch. These losses are consistent with the Convective Instability

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Space Charge Simulations of High Intensity Proton Beams in the AGS Booster

Computer simulation studies have been performed to understand the beam behavior and to explore intensity limitations of proton beams in the AGS Booster at higher beam intensities. During the 100 GeV polarized proton operations of RHIC Run 2024, sPHENIX operated in modes with a crossing angle at collisions in order to mitigate beam-beam effects. Three different running modes were employed: (a) sPHENIX operated with a negative (-2 mrad) crossing angle, and STAR operated with 0 mrad. Both experiments were brought into collisions at the start of the store. (b) sPHENIX was brought into collisions with 0 mrad first. Then STAR was brought into collisions after the beam-beam parameter from sPHENIX reduced to below $10 \times 10^{-3}$. (c) sPHENIX operated with a positive (+1.5 mrad) crossing angle, and STAR operated with 0 mrad. Both experiments were brought into collisions at the start of the store. The collisions with a crossing angle of up to $\pm 2$ mrad, as in running modes (a) and (c), lead to large Piwinski angle in the new sPHENIX detector, which reduces luminosity if other parameters are unchanged. There are two ways to compensate the reduction in luminosity: squeeze $\beta^{*}$ if there is sufficient dynamic aperture, or increase the injected beam intensity. The first part of polarized proton operation during RHIC Run 2024 was dedicated to increasing the intensity. Different configurations were tested with crossing angle and lattice adjustments on RHIC. At the same time, new injector configurations were developed and tested in an effort to push for both higher intensity and better quality of the beam injected into RHIC. When the beam intensity is increased, space charge is a concern particularly in the lower energy stages of acceleration, such as during the injection and the early part of the Booster cycle, which could become a dominant effect in limiting the intensity of the beam that can be delivered to RHIC.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Optimization and stabilization of Fermilab Booster using hybrid Bayesian/RL framework

PIPII project will raise Fermilab Booster intensity and ramp rate. Beam losses will limit average power and are hard to simulate. Presently, Booster uses operator-guided empirical tuning. This task is challenging due to high dimensionality, multiple objectives, critical safety constraints, and drifts. We developed a synergistic suite of Bayesian optimization (BO) and reinforcement learning (RL) tools to optimize and stabilize beam losses. First, active learning was used to build a rough model. Data was collected parasitically using two novel safety constraint types – nonlinear input space restrictions (based on optics model), and uncertainty constraints (to stop bad steps/beam aborts). We then applied online multi-objective BO with scalarized objectives and fitting to improve/rebalance losses, increasing safety margins by 25%. Using BO model as a safety veto, we tried several on/off-policy RL agents for long term stabilization; SAC had best performance. We found that adding contextual (state) information further improved performance, eventually integrating key knobs like linac phase and temperature into the parameter space. Long term testing is ongoing to enable operational use.

Kuklev, Nikita [Fermilab]↗
DOE OSTI2024

Observation of a Synchro-betatron Instability in Fermilab Booster

In preparation for PIP-II, there has been interest in running the Fermilab Booster at a higher current more indicative of the PIP-II era operation. In July 2023, an experiment was performed to study collective instabilities over the transition crossing at the Fermilab Booster. Over the transition crossing, the synchrotron tune becomes small and synchro-betatron instabilities become possible. During the experiment, an intensity threshold was observed, above which a dipole instability with losses concentrated in the tail of the bunch. These losses are consistent with the Convective Instability.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

An orphan gene BOOSTER enhances photosynthetic efficiency and plant productivity

Organelle-to-nucleus DNA transfer is an ongoing process playing an important role in the evolution of eukaryotic life. Here, genome-wide association studies (GWAS) of non-photochemical quenching parameters in 743 Populus trichocarpa accessions identified a nuclear-encoded genomic region associated with variation in photosynthesis under fluctuating light. The identified gene, BOOSTER (BSTR), comprises three exons, two with apparent endophytic origin and the third containing a large fragment of plastid-encoded Rubisco large subunit. Higher expression of BSTR facilitated anterograde signaling between nucleus and plastid, which corresponded to enhanced expression of Rubisco, increased photosynthesis, and up to 35% greater plant height and 88% biomass in poplar accessions under field conditions. Overexpression of BSTR in Populus tremula × P. alba achieved up to a 200% in plant height. Similarly, Arabidopsis plants heterologously expressing BSTR gained up to 200% in biomass and up to 50% increase in seed.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Resonance compensation at the CERN PS booster aided by Bayesian optimization and BOBYQA

The CERN Proton Synchrotron Booster (PSB) operation involves the crossing of multiple resonance lines in the tune diagram. Loss maps from dynamic tune scans are a helpful way to visualize and quantify the strength of such resonances. Sextupole and octupole correctors can be used in order to partially or fully compensate multiple resonance lines, i.e., third and fourth order lines. The following work explores the application of advanced optimization algorithms such as Bayesian Optimization and Bound Optimization By Quadratic Approximation (BOBYQA) in order to compensate these resonance lines with available correctors.

43 PARTICLE ACCELERATORS↗
DOE OSTI2026

Booster cavity damper redesign for PIP-II

A new Higher Order Mode (HOM) damper was designed and is undergoing testing for the Booster accelerator cavity at Fermilab. In anticipation of the PIP-II upgrade, it was discovered that the higher intensity of PIP-II may cause beam instability due to an excited mode at 106 MHz. This unfortunately corresponds with the cavity’s 2nd order harmonic mode, which will sweep from 86-105.7 MHz. The new damper is a modification of an existing damper that was designed to reduce an existing static HOM at 83 MHz, with the new design intending to cover the 2nd order HOM as well. The existing damper uses an inductive coupling loop to extract RF energy from the cavity which then goes through a filter in order to reflect the fundamental frequency back into the cavity while passing HOMs to a dump load. The new damper intends to replace the filter portion of the system with a wider band variant while also changing the topology from a coaxial cable loop filter to a componentized PCB-based design. Primary design challenges include bandwidth coverage, impedance matching of the various modes, long term thermal and mechanical stability, radiation hardness, and high voltage handling. Initial designs achieved the desired damping but were found to quickly succumb to destructive arcing due to the voltages present. More finalized designs intend to address this problem through circuit design modifications as well as the use of hardier components.

Pieper, Dustin [Fermilab]↗
DOE OSTI2024

Shortened Booster Bunch Lengths

Booster typically produces beam bunches that have a phase space profile with a low momentum spread but high time spread, correlating to longer bunch lengths. The goal of this study is to produce beam bunches that have a phase space profile with a high momentum spread but low time spread or narrow bunch lengths. This can be achieved by slowly increasing the RF cavities amplitudes (Adiabatic Excitation) or by oscillating the amplitudes (Quadratic Bunch Rotation, QBR) until the desired bunch lengths are achieved. Results show that when shortening the bunches using QBR, it showed the bunches had a length of 0.6ns (within 1 sigma) but beam losses were being incurred in the 8 GeV line which were a result of beam dispersion.

Abdelhamid, Maan↗
DOE OSTI2024

An Updated Simulation of the Booster Neutrino Beam

For accelerator neutrino experiments, an accurate prediction of the incoming neutrino flux is crucial for reducing uncertainties for all physics measurements. In this exciting period for the Short-Baseline Neutrino program at Fermilab, with far detector (ICARUS) already operating and the near detector (SBND) nearing operation, an updated flux model for the Booster Neutrino Beam (BNB) is presented. The BNB delivers 8 GeV protons to a beryllium target, subsequently producing neutrinos from the decay of the secondary beam of hadrons. A updated Monte-Carlo simulation of beam production in GEANT4 has been created, allowing predictions to be made for detectors with different baselines, offsets and sizes. This new simulation contains new features, such as a full neutrino ancestry to handle hadron production systematics with more precision, with a view to storing all resulting particles - including neutral mesons - from the proton-Beryllium scatter to allow the study of exotic BSM scenarios. Results are presented, with comparisons to the original flux simulated for the MiniBooNE experiment.

Paton, Josephine↗
DOE OSTI2024

Booster Neutrino Beam operations and neutrino flux prediction

The Booster Neutrino Beam (BNB) Line is used to produce neutrino beams for the 8 GeV Neutrino Program at Fermilab. This talk will provide a summary of the BNB operations and an estimate of the neutrino flux that is produced by the beamline. The talk will also summarize the work to upgrade the system which records the longitudinal structure of the primary proton beam that is delivered to BNB production target.

43 PARTICLE ACCELERATORS↗