Search NASA⌕ Search

SEARCH · Search NASA

Results for “Boundary plasma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Simulation of the SPARC plasma boundary with the UEDGE code

Here in this work, the UEDGE edge transport code is used to examine conditions in the SPARC divertor and edge plasma for various levels of carbon impurity and power from the core (P SOL ). A double-null magnetic configuration is simulated assuming up-down symmetry in geometry and physics. The anomalous heat and particle transport coefficients are tuned to match empirical predictions for SPARC's midplane density profiles, target plate heat flux profiles, and inner/outer divertor power sharing. Convective transport is included on the low-field side, while on the high-field side the transport is modeled as purely diffusive. Hydrogen neutrals are modeled as a fluid with inertial effects, and a carbon impurity is included using the fixed-fraction model. We find that detachment induced by impurity seeding could significantly reduce the heat flux to the divertor surfaces in the SPARC tokamak. At P SOL = 28 MW (the value predicted for SPARC's full-power H-mode scenario) cases with both divertor legs detached were obtained with a carbon impurity fraction between 0.3%–1.4%, far below Z eff limits for SPARC. When the plasma in the outer leg is detached, the peak heat flux density perpendicular to the target plate is below 1 MW m -2 , electron and ion temperatures are less than 1.5 eV, and momentum detachment is observed. However, the detachment state is found to be sensitive to the side-wall boundary conditions, the level of neutral pumping, and the target plate tilt. Finally, a broadly similar SOLPS simulation of SPARC is used to assess the appropriateness of the simpler impurity and neutral models used in UEDGE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Neural network reconstruction of the DIII-D tokamak plasma boundary using a reduced set of diagnostics

This study investigates the feasibility of reconstructing the last closed flux surface in the DIII-D tokamak using neural network models trained on reduced input feature sets, addressing an ill-posed task. Two models are compared: one trained solely on coil currents and another incorporating coil currents, plasma current and loop voltage. The model trained exclusively on coil currents achieved a mean point displacement of $0.04$ m on a held-out test set, while the inclusion of plasma current and loop voltage reduced the error to $0.03$ m. This comparison highlights the trade-offs between input feature complexity and reconstruction accuracy, demonstrating the potential of machine learning algorithms to perform effectively in data-limited environments, such as those expected in fusion power plants due to diagnostic constraints imposed by the presence of blankets and shielding.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Development of a tomographic reconstruction method for axisymmetric D α emission profiles in the ITER plasma boundary

A tomographic method for reconstructing the axially symmetric D α emission profile in the ITER scrape-off layer and divertor from D α intensity measurements in the fields of view (FoV) of Vis/IR TV and Divertor Impurity Monitor diagnostics is under development. The method takes into account the strong background signal due to stray light from divertor produced by reflections from the metal wall of the vacuum chamber. The method allows to filter out the reflections in D α signals measured in the main chamber. Here, the accuracy of this method is tested within the framework of a synthetic diagnostic, which uses the Raysect and Cherab numerical codes for ray-tracing simulations. The D α emission profiles, simulated with the SOLPS and OEDGE codes, are used as synthetic experimental data. Uncertainty in light reflection properties of the first wall (FW) is the major factor affecting the accuracy of the D α emission reconstruction. The dependence on the uncertainty in the FW surface roughness and on the ratio of diffusive to specular reflection of the error in recovering useful D α signals (the direct light without reflections) in the FoV of the ITER main chamber H-alpha and Visible Spectroscopy Diagnostic is obtained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Compression of tokamak boundary plasma simulation data using a maximum volume algorithm for matrix skeleton decomposition

This report demonstrates satisfactory data compression of SOLPS-ITER simulation output ranging from 2D fields, 1D profiles, and 0D scalar variables with a novel matrix decomposition approach. The singular value decomposition (SVD) scales poorly for large matrix sizes and is unsuited to the application on high dimensional data common to fusion plasma physics simulation. In this work, we employ the columns-submatrix-rows (CUR) matrix factorization technique in order to compute a low-rank approximation up to two orders of magnitude faster than the SVD, but within a nominal L2-norm relative error of ε = 10 –2 . In addition, the CUR approach maintains the original format of the data, in its extracted columns and rows, allowing for interpretable data storage at the original resolution of the simulation. We utilize an iterative algorithm to compute the CUR decomposition of simulation output by maximizing the volume, or linearly independent information content, of a low-rank submatrix contained within the data. Experiments over $\textit{n} × \textit{n}$ randomized test matrices with embedded rank-deficient features show that this maximum volume implementation of CUR matrix approximation has reduced asymptotic computational complexity on the order of n compared to the SVD, which scales approximately as $n^3$. These results show that the CUR technique can be used to effectively select time step snapshots (columns) of over 140 SOLPS-ITER output variables and the associated discretized coordinate timeseries (rows) allowing for reconstruction of the complete simulation dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Modeling rf sheath formation in turbulent tokamak boundary plasma

During ICRF antenna operation, complex interactions between turbulent density profiles, nonlinear RF sheaths, and RF-induced convective transport are observed to alter plasma density in the tokamak edge [D’Ippolito et al., Nucl. Fusion 38, 1543 (1998)]. In this work, we explore the physics of such interactions via numerical modeling, using a nonlinear EM/plasma/sheath code (VSim) and profiles obtained from a fluid plasma turbulence code (Hermes) in a 3D slab domain containing biased side-wall limiters. RF-rectified sheath formation on antenna and limiter surfaces is observed as electromagnetic waves launched by the antenna are refracted through the turbulent density profile. On transport timescales, such sheath potentials have been shown to influence both the mean species density and its RMS fluctuation spectrum [Smithe et al., these proceedings]. On the faster RF timescales, we demonstrate that the converse is also true – regions of high plasma density near material surfaces give rise to the highest sheath potential amplitudes. When density is turbulent and spatially nonuniform, localized regions of high sheath potential (hotspots) may develop where high-density filaments intersect material surfaces. Such hotspots are of particular concern as sources of impurity sputtering, and we explore their behavior in response to changes both to the local plasma density and to antenna operating parameters and structure. Related results exploring the role of Faraday shields and/or enclosing structures in suppressing high sheath potentials for other devices (e.g. SPARC) will also be shown.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Experimental study of the influence of gas puff locations on H-mode boundary plasmas with argon seeding on EAST

To investigate the optimal scenario of impurity seeding to obtain divertor plasma detachment for target protection, experiments with Ar&D 2 seeding from two different poloidal locations, the upper outer (UO) divertor target and lower outer (LO) target, were carried out on EAST. Partial energy detachment (the electron temperature near the strike point T e,spt ≤ 10 eV) were obtained with Ar&D 2 mixture puffing from the UO target and, for the first time, from the LO target into H-mode plasmas in the upper single null (USN) configuration. The peak heat flux q t on the UO target was significantly reduced (by ~80%). The rollover of ion flux density j s did not appear probably due to insufficient momentum loss, which is independent of the puff locations. The poloidal asymmetries of particle and heat fluxes on the targets have also been investigated. The UO-dominant asymmetry of particle flux was reversed, while the UO-dominant asymmetry of heat flux was mitigated but not reversed. The plasma confinement dropped by only 14% and 8.2% in the LO-puff case and UO-puff case, respectively, during detachment. The high level of C may contributed greatly to the higher radiation in the bulk plasma region and the greater decline in W MHD in the LO-puff case.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Simulating Boundary Region Plasma Instabilities

The boundary regions of low-temperature plasmas are known to be susceptible to kinetic instabilities, which can affect the energies and fluxes of particles directed at the material boundary. For example, both the ion acoustic instability as well as an instability near the electron plasma frequency have been observed. Particle-in-cell (PIC) simulation is a tool that, alongside experiments, can capture the effects these instabilities have on the particle distribution functions. Ultimately, simulations can determine under what conditions these effects are significant by comparing to theoretical predictions and explore conditions unamenable to experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

INGRID: An interactive grid generator for 2D edge plasma modeling

A fusion boundary-plasma domain is defined by axisymmetric magnetic surfaces where the geometry is often complicated by the presence of one or more X-points; and modeling boundary plasmas usually relies on computational grids that account for the magnetic field geometry. The new grid generator INGRID (Interactive Grid Generator) presented here is a Python-based code for calculating grids for fusion boundary plasma modeling, for a variety of configurations with one or two X-points in the domain. INGRID first performs partitioning over the domain consisting of a small number of patches conforming to the magnetic field and wall geometry; then it generates a subgrid on each of the patches and joins them into a global grid. This domain partitioning strategy makes possible a uniform treatment of various configurations with one or two X-points in the domain. This includes single-null, double-null, and other configurations with two X-points in the domain. The INGRID design allows generating grids either interactively, via a parameterfile driven GUI, or using a non-interactive script-controlled workflow. Results of testing demonstrate that INGRID is a flexible, robust, and user-friendly grid-generation tool for fusion boundary-plasma modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

INGRID: An interactive grid generator for 2D edge plasma modeling

A fusion boundary-plasma domain is defined by axisymmetric magnetic surfaces where the geometry is often complicated by the presence of one or more X-points; and modeling boundary plasmas usually relies on computational grids that account for the magnetic field geometry. The new grid generator INGRID (Interactive Grid Generator) presented in this work is a Python-based code for calculating grids for fusion boundary plasma modeling, for a variety of configurations with one or two X-points in the domain. INGRID first performs partitioning over the domain consisting of a small number of patches conforming to the magnetic field and wall geometry; then it generates a subgrid on each of the patches and joins them into a global grid. This domain partitioning strategy makes possible a uniform treatment of various configurations with one or two X-points in the domain. This includes single-null, double-null, and other configurations with two X-points in the domain. The INGRID design allows generating grids either interactively, via a parameter-file driven GUI, or using a non-interactive script-controlled workflow. Results of testing demonstrate that INGRID is a flexible, robust, and user-friendly grid-generation tool for fusion boundary-plasma modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Control of neutral fueling and helium exhaust to NSTX-U plasmas by means of three-dimensional magnetic control fields

Resonant magnetic perturbations are used to stabilize plasma edge instabilities, so-called edge localized modes (ELMs), in high-performance (H-mode) plasmas explored for fusion energy. These ELMs cause repetitive outburst of confined energy and particles and cause cyclic loading of plasma facing components (PFCs). This endangers the integrity of the PFCs and hence limits the lifetime and hence commercial viability of fusion. It was shown that these ELMs can be stabilized by application of small amplitude resonant magnetic perturbation (RMP) fields. This removes the ELMs as edge instabilities but also induces three-dimensional (3D) effects to the plasma boundary, which was formerly toroidally axisymmetric. The impact of this 3D perturbation on the plasma boundary solution needs to be understood to extrapolate the effects to ITER and towards a fusion reactor, if ELM control by RMP fields would be utilized.

3D Boundary Plasmas↗
DOE OSTI2020

FY2018 Fusion Theory and Simulation Milestone on Plasma Materials Interaction (PMI) (Final Report)

The interaction of the boundary plasma with the material surfaces in magnetically confined plasmas is among the most critical problems in fusion energy science. In FY2018, perform high performance computing simulations with coupled boundary plasma physics and materials surface models to predict the fuel recycling and tritium retention of the ITER divertor for D-T burning plasma conditions, accounting for erosion, re-deposition and impurity transport in the plasma boundary, and an initial evaluation of the influence of material deposition on the recycling and retention.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Modelling of edge plasma dynamics with active wall boundary conditions

A self-consistent 2D model is presented for transport in boundary plasma and plasma-facing material walls. Plasma dynamics in the domain is represented by a 2D collisional plasma fluid model in the edge-plasma code UEDGE, and transport of hydrogen and heat in the wall is represented by a system of reaction–diffusion equations in the 1D wall code FACE. To account for variation of parameters along the wall, in the coupled model multiple instances of the FACE code run in parallel. Here, the coupled model provides a tool for investigating a range of dynamic plasma–material interactions phenomena in 2D. For demonstration of its capability, one application of particular interest is the role of active wall in tokamak strike point sweeping proposed for mitigation of divertor heat loads. In the present study, the coupled calculations are applied to investigation of the impact of heat and hydrogen transport in the material wall on the divertor plasma and target heat load during sweeping of the target strike point for parameters of a high-power tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗