Search NASA⌕ Search

SEARCH · Search NASA

Results for “Broadband Noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Broadband Noise Prediction of Two Small Hovering Rotors using FUN3D-ANOPP2

A computational study was performed on two small hovering rotors, the ideally twisted rotor and the optimum hovering 2-bladed rotor, using FUN3D-ANOPP2. The effects of different inviscid upwinding techniques and temporal resolutions on aerodynamic performance and acoustic prediction were compared against experimental data obtained in the Small Hover Anechoic Chamber facility at the NASA Langley Research Center. Decreasing the numerical dissipation with 𝜅 tuning or by using a higher-order inviscid flux reconstruction scheme was shown to improve aerodynamic performance predictions when compared to measured data for most cases. The effect of dissipation on the vorticity field was also seen to influence the amount of turbulence surrounding the vortex core of the first blade-vortex interaction (BVI), the coherence of the second and higher BVI vortex cores, and the downstream breakdown of the rotor wake for both rotor geometries. Tonal and broadband noise predictions from simulation cases with lower dissipation were seen to agree better with the experiment for the ideally twisted rotor, whereas temporal resolution differences had negligible impact on the broadband noise results. Similar fundamental BPF directivity patterns were obtained by all simulation cases for the optimum hovering 2-bladed rotor, while the most accurate 2*BPF directivity trend, compared to the experiment, was predicted by the lower-dissipation case at the coarse temporal resolution, albeit with an amplitude underprediction. Broadband noise spectral roll-off behavior was seen to occur at a higher frequency when using a finer temporal resolution for the optimum hovering 2-bladed rotor, unlike for the ideally twisted rotor geometry. The broadband noise prediction for the optimum hovering 2-bladed rotor from the higher-dissipation case at the coarse temporal resolution was also seen to predict a tone centered around approximately 8.5 kHz, which was similar in amplitude to the measured tone around 16.5 kHz.

Christopher S. Thurman↗
NASA NTRS1998

Boeing 18-Inch Fan Rig Broadband Noise Test

The purposes of the subject test were to identify and quantify the mechanisms by which fan broadband noise is produced, and to assess the validity of such theoretical models of those mechanisms as may be available. The test was conducted with the Boeing 18-inch fan rig in the Boeing Low-Speed Aeroacoustic Facility (LSAF). The rig was designed to be particularly clean and geometrically simple to facilitate theoretical modeling and to minimize sources of interfering noise. The inlet is cylindrical and is equipped with a boundary layer suction system. The fan is typical of modern high-by-pass ratio designs but is capable of operating with or without fan exit guide vanes (stators), and there is only a single flow stream. Fan loading and tip clearance are adjustable. Instrumentation included measurements of fan performance, the unsteady flow field incident on the fan and stators, and far-field and in-duct acoustic fields. The acoustic results were manipulated to estimate the noise generated by different sources. Significant fan broadband noise was found to come from the rotor self-noise as measured with clean inflow and no boundary layer. The rotor tip clearance affected rotor self-noise somewhat. The interaction of the rotor with inlet boundary layer turbulence is also a significant source, and is strongly affected by rotor tip clearance. High level noise can be generated by a high-order nonuniform rotating at a fraction of the fan speed, at least when tip clearance and loading are both large. Stator-generated noise is the loudest of the significant sources, by a small margin, at least on this rig. Stator noise is significantly affected by propagation through the fan.

Ganz, Ulrich W.↗
NASA NTRSDate not supplied

NASA/ONERA Collaboration on Small Hovering Rotor Broadband Noise Prediction using Lattice-Boltzmann and Structured Navier-Stokes Solvers

This work compares two lattice-Boltzmann method solvers, PowerFLOW and ProLB, and two structured Navier-Stokes solvers, OVERFLOW2 and FAST, used by NASA and ONERA, respectively, for the broadband noise prediction of an ideally twisted rotor as part of Implementing Arrangement number FR-0685-0, ‘Comparing Computational Fluid Dynamics Solvers for Broadband Noise Prediction.’ Predicted results are evaluated against measured data from both smooth and rough blade sets acquired in the Small Hover Anechoic Chamber at the NASA Langley Research Center. Aerodynamic thrust predictions are seen to agree more favorably with the rough-blade measurements, whereas torque predictions agree better with the smooth-blade measurements. A tonal noise comparison shows better agreement to the measured data with the two structured Navier-Stokes solvers than with the two lattice-Boltzmann solvers, which is thought to be caused by the different geometric discretization associated with each solver paradigm. Broadband noise comparisons show that both lattice-Boltzmann method solvers trend well with the smooth-blade measurements, with the exception of an overprediction by ProLB between 4 kHz and 15 kHz. OVERFLOW2 is seen to capture the measured nondeterministic tonal content between 3 kHz and 8 kHz on a narrowband spectral basis and FAST agrees well with the rough blades on a one-third octave band basis.

Christopher S. Thurman↗
NASA NTRS1984

Prediction of broadband noise from large horizontal axis wind turbine generators

A method is presented for predicting the broadband noise spectra of large horizontal axis wind turbine generators. It includes contributions from such noise sources as the inflow turbulence to the rotor, the interactions between the turbulent boundary layers on the blade surfaces with their trailing edges and the wake due to a blunt trailing edge. The method is partly empirical and is based on acoustic measurements of large wind turbines and airfoil models. The predicted frequency spectra are compared with measured data from several machines including the MOD-OA, the MOD-2, the WTS-4 and the U.S. Wind-power Inc. machine. Also included is a broadband noise prediction for the proposed MOD-5B. The significance of the effects of machine size, power output, trailing edge bluntness and distance to the receiver is illustrated. Good agreement is obtained between the predicted and measured far field noise spectra.

Grosveld, F. W.↗
NASA NTRS2001

Rotor Broadband Noise Prediction with Comparison to Model Data

This paper reports an analysis and prediction development of rotor broadband noise. The two primary components of this noise are Blade-Wake Interaction (BWI) noise, due to the blades' interaction with the turbulent wakes of the preceding blades, and "Self" noise, due to the development and shedding of turbulence within the blades' boundary layers. Emphasized in this report is the new code development for Self noise. The analysis and validation employs data from the HART program, a model BO-105 rotor wind tunnel test conducted in the German-Dutch Wind Tunnel (DNW). The BWI noise predictions are based on measured pressure response coherence functions using cross-spectral methods. The Self noise predictions are based on previously reported semiempirical modeling of Self noise obtained from isolated airfoil sections and the use of CAMRAD.Modl to define rotor performance and local blade segment flow conditions. Both BWI and Self noise from individual blade segments are Doppler shifted and summed at the observer positions. Prediction comparisons with measurements show good agreement for a range of rotor operating conditions from climb to steep descent. The broadband noise predictions, along with those of harmonic and impulsive Blade-Vortex Interaction (BVI) noise predictions, demonstrate a significant advance in predictive capability for main rotor noise.

Brooks, Thomas F.↗
NASA NTRSDate not supplied

Evaluation of a Variable Facesheet Liner Configuration in Grazing Incidence for Broadband Noise Reduction

Tests were conducted in the NASA Langley Grazing Flow Impedance Tube (GFIT) to determine the broadband noise reduction capability of a variable facesheet liner. Three uniform liners were designed to achieve sound absorption over distinct frequency regimes at Mach 0.0. Each liner was fabricated and tested in the GFIT at sound pressure levels of 120 and 140 dB, and at tangential flow velocities up to Mach 0.5. A variable facesheet liner was fabricated to combine the geometries of these three liners, such that the facesheet geometry (hole diameter and porosity) was varied across the liner surface. The Prony method was used to educe the impedance of each sample, and these impedances were input to the CHE (Convected Helmholtz Equation) propagation code to predict the acoustic pressure profiles in the GFIT. Comparisons of predicted and measured acoustic pressure profiles were used to confirm the uniformity of all four liners, and to demonstrate the suitability of the CHE code in the analysis of the variable facesheet concept. Results showed good comparison at no flow and at Mach 0.3, and acceptable comparison at Mach 0.5. The variable facesheet liner provided enhanced broadband noise reduction at the no-flow condition for which it was designed, but further optimization is needed to target flow conditions.

acoustic↗
NASA NTRSDate not supplied

Evaluation of a Variable Facesheet Liner Configuration in Grazing Incidence for Broadband Noise Reduction

Abstract Tests were conducted in the NASA Langley Grazing Flow Impedance Tube (GFIT) to determine the broadband noise reduction capability of a variable facesheet liner. Three uniform liners were designed to achieve sound absorption over distinct frequency regimes at Mach 0.0. Each liner was fabricated and tested in the GFIT at sound pressure levels of 120 and 140 dB, and at tangential flow velocities up to Mach 0.5. A variable facesheet liner was fabricated to combine the geometries of these three liners, such that the facesheet geometry (hole diameter and porosity) was varied across the liner surface. The Prony method was used to educe the impedance of each sample, and these impedances were input to the CHE (Convected Helmholtz Equation) propagation code to predict the acoustic pressure profiles in the GFIT. Comparisons of predicted and measured acoustic pressure profiles were used to confirm the uniformity of all four liners, and to demonstrate the suitability of the CHE code in analysis of the variable facesheet concept. Results showed good comparison at no flow and Mach 0.3, and acceptable comparison at Mach 0.5. The variable facesheet liner provides enhanced broadband noise reduction at the no-flow condition for which it was designed, but further optimization is needed to target flow conditions.

acoustic↗
NASA NTRS2001

Broadband Noise of Fans - With Unsteady Coupling Theory to Account for Rotor and Stator Reflection/Transmission Effects

This report examines the effects on broadband noise generation of unsteady coupling between a rotor and stator in the fan stage of a turbofan engine. Whereas previous acoustic analyses treated the blade rows as isolated cascades, the present work accounts for reflection and transmission effects at both blade rows by tracking the mode and frequency scattering of pressure and vortical waves. The fan stage is modeled in rectilinear geometry to take advantage of a previously existing unsteady cascade theory for 3D perturbation waves and thereby use a realistic 3D turbulence spectrum. In the analysis, it was found that the set of participating modes divides itself naturally into "independent mode subsets" that couple only among themselves and not to the other such subsets. This principle is the basis for the analysis and considerably reduces computational effort. It also provides a simple, accurate scheme for modal averaging for further efficiency. Computed results for a coupled fan stage are compared with calculations for isolated blade rows. It is found that coupling increases downstream noise by 2 to 4 dB. Upstream noise is lower for isolated cascades and is further reduced by including coupling effects. In comparison with test data, the increase in the upstream/downstream differential indicates that broadband noise from turbulent inflow at the stator dominates downstream noise but is not a significant contributor to upstream noise.

Hanson, Donald B.↗
NASA NTRS2003

Some Analytic Results for the Study of Broadband Noise Radiation from Wings, Propellers and Jets in Uniform Motion

Alan Powell has made significant contributions to the understanding of many aeroacoustic problems, in particular, the problems of broadband noise from jets and boundary layers. In this paper, some analytic results are presented for the calculation of the correlation function of the broadband noise radiated from a wing, a propeller, and a jet in uniform forward motion. It is shown that, when the observer (or microphone) motion is suitably chosen, the geometric terms of the radiation formula become time independent. The time independence of these terms leads to a significant simplification of the statistical analysis of the radiated noise, even when the near field terms are included. For a wing in forward motion, if the observer is in the moving reference frame, then the correlation function of the near and far field noise can be related to a space-time cross-correlation function of the pressure on the wing surface. A similar result holds for a propeller in forward flight if the observer is in a reference frame that is attached to the propeller and rotates at the shaft speed. For a jet in motion, it is shown that the correlation function of the radiated noise can be related to the space-time crosscorrelation of the Lighthill stress tensor in the jet. Exact analytical results are derived for all three cases. For the cases under present consideration, the inclusion of the near field terms does not introduce additional complexity, as compared to existing formulations that are limited to the far field.

Farassat, F.↗
NASA NTRS2003

Some Analytic Results for the Study of Broadband Noise Radiation from Wings, Propellers and Jets in Uniform Motion

Alan Powell has made significant contributions to the understanding of many aeroacoustic problems, in particular, the problems of broadband noise from jets and boundary layers. In this paper, some analytic results are presented for the calculation of the correlation function of the broadband noise radiated from a wing, a propeller, and a jet in uniform forward motion. It is shown that, when the observer (or microphone) motion is suitably chosen, the geometric terms of the radiation formula become time independent. The time independence of these terms leads to a significant simplification of the statistical analysis of the radiated noise, even when the near field terms are included. For a wing in forward motion, if the observer is in the moving reference frame, then the correlation function of the near and far field noise can be related to a space-time cross-correlation function of the pressure on the wing surface. A similar result holds for a propeller in forward flight if the observer is in a reference frame that is attached to the propeller and rotates at the shaft speed. For a jet in motion, it is shown that the correlation function of the radiated noise can be related to the space-time crosscorrelation of the Lighthill stress tensor in the jet. Exact analytical results are derived for all three cases. For the cases under present consideration, the inclusion of the near field terms does not introduce additional complexity, as compared to existing formulations that are limited to the far field.

Farassat, F.↗
NASA NTRS2012

Broadband Noise Prediction When Turbulence Simulation Is Available - Derivation of Formulation 2B and Its Statistical Analysis

We show that a simple modification of Formulation 1 of Farassat results in a new analytic expression that is highly suitable for broadband noise prediction when extensive turbulence simulation is available. This result satisfies all the stringent requirements, such as permitting the use of the exact geometry and kinematics of the moving body, that we have set as our goal in the derivation of useful acoustic formulas for the prediction of rotating blade and airframe noise. We also derive a simple analytic expression for the autocorrelation of the acoustic pressure that is valid in the near and far fields. Our analysis is based on the time integral of the acoustic pressure that can easily be obtained at any resolution for any observer time interval and digitally analyzed for broadband noise prediction. We have named this result as Formulation 2B of Farassat. One significant consequence of Formulation 2B is the derivation of the acoustic velocity potential for the thickness and loading terms of the Ffowcs Williams-Hawkings (FW-H) equation. This will greatly enhance the usefulness of the Fast Scattering Code (FSC) by providing a high fidelity boundary condition input for scattering predictions.

Farassat, Fereidoun↗
NASA NTRS1978

Influence of internally generated pure tones on the broadband noise radiated from a jet

An experimental study was conducted to determine subsonic-jet-noise amplification by plane waves of sound (pure tones) generated upstream of the nozzle over wide ranges of frequency and amplitude. The data were used to evaluate the behavior of the pure tone and the broadband parts of the radiated sound in the far field. It is shown that a significant increase of broadband noise occurs only when the amplitude of the tone in the far field exceeds the sound pressure of the broadband noise at the same location in the far field. Therefore, the sensitivity of the jet to the pure-tone excitation is not large.

Parthasarathy, S. P.↗
NASA NTRS2015

Evaluation of Variable-Depth Liner Configurations for Increased Broadband Noise Reduction

This paper explores the effects of variable-depth geometry on the amount of noise reduction that can be achieved with acoustic liners. Results for two variable-depth liners tested in the NASA Langley Grazing Flow Impedance Tube demonstrate significant broadband noise reduction. An impedance prediction model is combined with two propagation codes to predict corresponding sound pressure level profiles over the length of the Grazing Flow Impedance Tube. The comparison of measured and predicted sound pressure level profiles is sufficiently favorable to support use of these tools for investigation of a number of proposed variable-depth liner configurations. Predicted sound pressure level profiles for these proposed configurations reveal a number of interesting features. Liner orientation clearly affects the sound pressure level profile over the length of the liner, but the effect on the total attenuation is less pronounced. The axial extent of attenuation at an individual frequency continues well beyond the location where the liner depth is optimally tuned to the quarter-wavelength of that frequency. The sound pressure level profile is significantly affected by the way in which variable-depth segments are distributed over the length of the liner. Given the broadband noise reduction capability for these liner configurations, further development of impedance prediction models and propagation codes specifically tuned for this application is warranted.

Jones, M. G.↗
NASA NTRS1982

Model helicopter rotor low frequency broadband noise

The results of an experimental investigation of low frequency broadband noise (LFBN) radiated from model helicopter rotors are presented. The results up to tip Mach number of 0.50 suggest that the peak sound pressure level (SPL) of LFBN appears to follow tip Mach number to a fourth power law and rms velocity of turbulence to a second power law. The experimental results on the effect of tip speed and advance ratio on the peak SPL of LFBN can be explained on the basis of a simple scaling law. However, the experimental results on the effect of blade loading on the peak SPL of LFBN is still not clearly understood. A simple peak SPL scaling law for noise from a helicopter in forward flight encountering a sinusoidal gust is also developed. The trends predicted by the scaling law with the experimental results are found satisfactory for the cases of variation of the peak SPL of LFBN with tip speed and advance ratio.

Humbad, N. G.↗
NASA NTRS1983

Progress in rotor broadband noise research

The current status of research on various rotor broadband noise sources is reviewed. Theoretical modeling techniques which appear to have the most promise in the development of successful noise prediction capabilities are emphasized. The types of noise considered include: turbulence ingestion noise, blade self-noise due to turbulence passing the trailing edge, blade self-noise due to separated flow, and blade self-noise due to vortex shedding. Comparisons with experimental results are given, and present theoretical and experimental limitations are delineated to help identify areas of needed research.

Brooks, T. F.↗
NASA NTRS1986

Analyses of broadband noise mechanisms of rotors

The various source mechanisms which generate broadband noise on a range of rotors are reviewed. Analyses of these mechanisms are presented and compared to existing experimental data. The sources considered are load fluctuations due to inflow turbulence, due to turbulent blade boundary layers passing the trailing edge, and due to tip vortex formation turbulence. Vortex shedding noise due to laminar boundary layers and blunt trailing edges is not considered in detail as it can be avoided in most cases. Present analyses are adequate to predict the spectra from a wide variety of experiments on fans, helicopter rotors, and wind turbines to within about 5 to 10 dB. Better knowledge of the inflow turbulence improves the accuracy of the predictions. Inflow turbulence noise depends strongly on ambient conditions and dominates at low frequencies. Trailing edge and tip vortex noise are important at higher frequencies if inflow turbulence is weak. Boundary layer trailing edge noise increases slowly with angle of attack but not as rapidly as tip vortex formation noise. Tip noise can be important at high angles of attack for wide chord, square edge tips.

George, A. R.↗
NASA NTRS2015

Assessment of Geometry and In-Flow Effects on Contra-Rotating Open Rotor Broadband Noise Predictions

Application of previously formulated semi-analytical models for the prediction of broadband noise due to turbulent rotor wake interactions and rotor blade trailing edges is performed on the historical baseline F31/A31 contra-rotating open rotor configuration. Simplified two-dimensional blade element analysis is performed on cambered NACA 4-digit airfoil profiles, which are meant to serve as substitutes for the actual rotor blade sectional geometries. Rotor in-flow effects such as induced axial and tangential velocities are incorporated into the noise prediction models based on supporting computational fluid dynamics (CFD) results and simplified in-flow velocity models. Emphasis is placed on the development of simplified rotor in-flow models for the purpose of performing accurate noise predictions independent of CFD information. The broadband predictions are found to compare favorably with experimental acoustic results.

Zawodny, Nikolas S.↗