Search NASA⌕ Search

SEARCH · Search NASA

Results for “COLD WORKING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Recrystallization driven softening and heating rate dependencies of FeCrAl nuclear fuel cladding during accident transients

A refined understanding of FeCrAl cladding behavior during rapid transients is critical for its potential deployment in light-water reactors. Current assessments focus on transient burst testing metrics such as balloon geometry, burst temperature, and hoop stress, often used as proxies for simpler conventional tensile properties. However, directly correlating isothermal tensile and creep data with accident transient scenarios remains a challenge, although it is essential for high fidelity model development. Recent modeling based on tensile tests up to 800 °C, conducted with both immediate loading and a 10-minute soak, showed that immediate loading better predicts experimental burst temperatures, indicating a thermal softening effect. Building upon this observation, the current study connects transient performance, microstructural evolution, and high-temperature tensile properties by leveraging results from C26M claddings burst tests performed at heating rates of 1–50 °C/s and hoop stresses from 25 to 100 MPa. At 25 MPa, rupture temperatures varied by only 6 °C, but at 100 MPa, the difference reached 116 °C, with faster heating yielding higher burst temperatures. Microstructural analysis identified recrystallization as the primary cause of heating rate-dependent softening, eliminating prior cold-working. In-situ thermomechanical data linked ballooning onset to localized instabilities, similar to ultimate tensile strength behavior in conventional tensile tests. High heating rates correlated with immediate loading tensile data, while lower rates matched soaked data. Furthermore, by linking burst performance to microstructural evolution and tensile properties, this work provides a foundation for more accurate modeling of FeCrAl claddings and potentially other Fe-based materials under accident conditions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Effects of Heat Treatment on Microstructure, Thermal Transport and Stability in SRF Niobium

Efficient heat transfer and thermal stability are critical for preventing thermal quench and ensuring the high performance and reliability of superconducting radiofrequency (SRF) cavities, especially under high RF fields. In this article, we investigate thermal conductivity and heat capacity of high-purity cold-worked niobium used in SRF applications, with a particular focus on the effects of high-temperature heat treatments. Our measurements reveal a pronounced sensitivity of thermal transport and thermodynamic properties to the underlying microstructure such as grain size and dislocation density. The results show the critical role of controlled heat treatment processes in optimizing the thermal performance of SRF niobium, providing valuable insights for improving cavity fabrication and processing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Comprehensive Review on Finite Element Analysis of Laser Shock Peening

Laser shock peening (LSP) is a formidable cold working surface treatment that provides high-energy precision to enhance the mechanical properties of materials. This paper delves into the intricacies of the LSP process, offering insights into its methodology and the simulation thereof through the finite element method. This review critically examines various points, such as laser energy, overlapping of shots, effect of LSP on residual stress, effect of LSP on grain refinement, and algorithms for simulation extrapolated from finite element analyses conducted by researchers, shedding light on the nuanced considerations integral to this technique. As the significance of LSP continues to grow, the collective findings underscore its potential as a transformative technology for fortifying materials against mechanical stress and improving their overall performance and longevity. The discourse encapsulates the evolving landscape of the LSP, emphasizing the pivotal role played by finite element analysis in advancing our understanding and application of this innovative surface treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cold air quench control of local crystallization environment in fully air-processed carbon-based perovskite solar cells

Carbon-based perovskite solar cells (C-PSCs) present a low-cost route to efficient photovoltaic technology. Gas quenching is an essential process commonly used for solvent extraction in scalable module fabrication using solution processes, but film quality remains highly sensitive to the localized environmental processing temperature, especially during intermediate phase transitions before perovskite film high temperature annealing. In this study, we introduce a cold air quench strategy to precisely control the local crystallization temperature that simultaneously promotes uniform crystallization and facilitates strain relaxation in fully air-processed C-PSCs. It is found that implementing dry air at 10 °C as the quenching gas yields a champion power conversion efficiency (PCE) of 20.52 %, with preferential (110) orientation and reduced, homogenized in-plane strain. This newly developed technique of a cost-effective low temperature air quenching process also enhances carrier lifetime, reduces interface recombination, and improves charge extraction. Furthermore, this work presents cold air quenching as a scalable, economic method to control perovskite crystallization and strain in C-PSC fabrication, advancing the industrial viability of high-performance perovskite modules.

14 SOLAR ENERGY↗
DOE OSTI2026

Cold Trap Replacement Project Report

This report documents the replacement of the Mechanisms Engineering Test Loop (METL) cold trap. The work involved preparation of the facility to replace the cold trap, removal of the existing welded cold trap from the sodium purification circuit, installation of a new replacement cold trap, completion of associated welds and examinations, restoration of instrumentation and heaters, and controlled return of the cold trap circuit to service. The replacement represented a significant maintenance evolution because the cold trap is an integral welded component of the sodium system. As a result, the work required coordinated control of sodium chemistry, deliberate formation of freeze plugs, inert gas management, precision cutting and welding, and a staged reheating and refill sequence. The activity was executed using procedural controls intended to protect personnel, preserve system cleanliness, and maintain the integrity of the sodium boundary throughout the work. This report provides a narrative summary of the milestone, including the purpose of the work, the pre-job system condition, the major field activities performed, observations made during execution, and the resulting post-work condition of the METL cold trap circuit.

42 ENGINEERING↗
DOE OSTI2025

Comparative performance assessment of air-source and ground-source heat pumps using CO₂ and R-410A with water well integration: A simulation study

This study investigates the performance and feasibility of heat pump systems for residential space heating in cold climates, with a particular focus on ground source heat pumps (GSHPs) with water wells. Four configurations are modeled and compared, a CO 2 air-source heat pump (ASHP), an R-410A ASHP, a CO 2 GSHP with water well integration, and an R-410A ground-source heat pump with water well integration. System simulations are conducted at both equipment and whole-building levels, followed by a nationwide analysis across ten representative cities using EnergyPlus. Results show that water-well-coupled GSHPs maintain approximately 87 % of their efficiency and 85.5 % of heating capacity as ambient temperature drops from 47 °F/8.3 °C to −15 °F/-26.1 °C, whereas ASHPs retain only 55 % efficiency and 44.5 % capacity. R-410A systems achieve higher efficiency, while CO 2 systems provide significant environmental advantages, including reduced risks of groundwater contamination from refrigerant leakage. On average, the CO 2 GSHPs deliver 35–45 % heating energy savings relative to ASHPs and demonstrate strong potential as a replacement for gas furnaces in cold climates. This work represents a systematic comparative assessment of CO 2 and R-410A air-source and ground-source heat pumps with water well integration. In conclusion, the findings highlight the technical viability, environmental benefits and deployment potential of CO 2 GSHPs, offering a pathway toward efficient and sustainable residential heating solutions in diverse U.S. climates.

CO 2 GSHP↗
DOE OSTI2025

SCULPT (Supervised Clustering and Uncovering Latent Patterns with Training) v1

SCULPT (Supervised Clustering and Uncovering Latent Patterns with Training) is a comprehensive data visualization and analysis application focused on working with COLTRIMS (COLd Target Recoil Ion Momentum Spectroscopy) data, which is used in atomic and molecular physics experiments. The application offers several powerful features: - Data uploading and processing capabilities for COLTRIMS files - Multiple visualization methods using UMAP (Uniform Manifold Approximation and Projection) for dimensionality reduction - Interactive selection of data points across multiple views - Feature engineering through various methods: - Manual feature selection from calculated physics parameters - Deep autoencoder for dimension reduction - Genetic programming for discovering meaningful features - Mutual information-based feature selection - Multiple clustering approaches (DBSCAN, KMeans, Agglomerative) - Quality metrics for evaluating clustering results - Export capabilities for selections and generated features

Daoud, Hazem [Lawrence Berkeley National Laborator↗
DOE OSTI2026

Comparative Study of Zinc Cold-Spray Coating and Pre-treatments for Magnesium Alloys

Magnesium (Mg) alloys are appealing for automotive lightweighting owing to their high specific strength. However, their susceptibility to corrosion in harsh environments remains a major challenge. Conventional industrial pre-treatment coatings, including zinc phosphate, chromate conversion, and non-chromate conversion, often exhibit discontinuities and microcracks, leading to localized corrosion near fasteners and parting lines. Here, this study investigates cold-sprayed zinc (Zn) coatings as a novel pre-treatment alternative for high-pressure die cast (HPDC) AZ91 Mg alloys, demonstrating significant improvements in wear and corrosion performance. Cold spray produces uniform and robust coatings, reducing wear rate by over 50% and reducing corrosion rate by over 99.3%, as measured by evolved hydrogen release, compared to traditional pre-treatments. Multimodal corrosion testing reveals that Zn cold-spray coatings form a protective layer during exposure, minimizing general and filiform corrosion, and exhibiting corrosion potential (E corr ) that is nobler by ~ 400 mV than the surfaces of both pre-treated and uncoated AZ91. Scalability of cold spray for selective application around multimaterial joints further strengthens their industrial viability. This work establishes Zn cold-spray coatings as highly effective pre-treatment solutions for the advancement of corrosion resistant Mg alloy components in automotive applications.

multimodal corrosion↗
DOE OSTI2024

Techno-Economic Analysis and Market Potential of Geological Thermal Energy Storage (GeoTES) Charged With Solar Thermal and Heat Pumps

In this project, we developed a techno-economic analysis (TEA) model that can be used to evaluate the viability of a proposed Geological Thermal Energy Storage (GeoTES) design. This MATLAB-based model integrates distinct subsystem models for the reservoir, wells, power cycle, and solar field to capture their distinct characteristics. It applies this approach in simulating GeoTES storage and dispatch operations for durations ranging from hourly to seasonal. Using cases studies based on GeoTES designs provided by industry partners - Premier Resource Management (PRM) and EarthBridge Energy - we validated the TEA model estimations of system performance and costs (such as thermal and electrical power/energy inflow and outflow, capital costs, and levelized costs of energy and storage) for both concentrating solar thermal (CST) and Carnot Battery (CB) pairings with GeoTES (CST-GeoTES and CB-GeoTES). For the CST-GeoTES case, the model was validated against the proposed system designed by PRM. It showed good agreement with PRM's estimations when well and pump costs derived from PRM's estimations were used. When GETEM-based costs were used, there was a slight overprediction due to GETEM's project/site agnostic assumption of these costs. From a sensitivity analysis perspective, the levelized cost of electricity (LCOE) of the CST-GeoTES case was most sensitive to well flow rate and the charging temperature. An optimal design scenario resulted in an LCOE of 0.11 $\$$/kWhe. CST-GeoTES can also provide a source of heat to meet seasonal demands. With 12-hour and 24-hour levelized cost of heat (LCOH) of 0.018 $\$$/kWhth and 0.022 $\$$/kWhth, respectively, CST-GeoTES could be competitive in the California market with an average industrial price of natural gas in California between 0.041-0.047 $\$$/kWhth. The levelized cost of storage (LCOS) for CST-GeoTES depends on the energy storage duration. Although the LCOS is relatively higher for shorter durations (e.g., ~0.50 $\$$/kWhe for 1 hour of storage), it is an order of magnitude lower (0.06 $\$$/kWhe) for longer storage durations and competitive with lithium-ion batteries (beyond 12 hours of storage) and molten-salt thermal energy storage (beyond 32 hours). Energy. Three options were explored and applied to the EarthBridge case study: (1) A Carnot Battery design using R125 working fluid with both hot and cold storage; (2) A Carnot Battery design using R125 working fluid with only hot storage; (3) A Carnot Battery using a commercially available heat pump with carbon dioxide (CO2) working fluid and hot storage only. The CB-GeoTES with cold storage only had a slight (round-trip) efficiency advantage over the system without (43.4% vs. 42.8%). This is because the cold storage is limited by the freezing point of water, so the cold storage is not much colder than the environment. The system using commercially available technologies was the least efficient - partly because different cycles were used in the heat pump (CO2) and heat engine (binary cycle) which leads to some inefficiencies. Using the commercially available design, the levelized cost of energy (LCOS) from the model (0.10 $\$$/kWhe) was higher than that estimated by EarthBridge (0.068 $\$$/kWhe). This is because of the low round-trip (38.7%) efficiency of the commercially available design. Sensitivity analysis reveals that the model is most sensitive to electricity price. Including electricity price in the TEA for CB-GeoTES leads to an increase in LCOS from the base value to 0.25 $\$$/kWhe. To determine storage sites suitable for GeoTES, we gathered and analyzed geological, petrophysical, and geophysical data of oil and gas reservoir and aquifers in California and Texas. We down-selected possible sites based on cut-off values for site characteristics (e.g., reservoir temperature, formation thickness, permeability, porosity, depth, and brine salinity) and preliminary costs. Using this approach, the Carrizo-Wilcox, Yegua-Jackson, and Dockum brackish aquifers in Texas were identified as having the highest suitability. Similarly, in the central California region, the White Wolf, Belridge South Tulare, and Belridge South Reef Ridge were the most suitable. Going further, we assessed the storage potential in the selected sites. To do this we developed distributions of reservoir characteristic data and applied a Monte Carlo-based analysis to account for intrinsic uncertainty in the acquired data. The analysis revealed that the Carrizo-Wilcox aquifer had the highest storage potential with a mean capacity of 554 TWhth (i.e., 63 TWhe). The estimated capacity serves as an upper limit of storage potential given that not all fields in the basin will be developed. We participated in multiple outreach activities including conference presentations, panel session discussions, and the facilitation of a GeoTES workshop at the NREL Golden campus.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

Cyber-Physical Simulation of the Cold Startup of Solid Oxide Fuel Cell – Gas Turbine (SOFC-GT) Hybrid Systems

This work introduces experimental studies for the cold startup process (CPS) of the SOFC-GT hybrid system using the cyber-physical simulation approach. The physical gas turbine is coupled with a cyber-physical SOFC stack, which is represented using the integration of a real time dynamic SOFC model with physical components (e.g., pressure chamber, natural gas burner, etc.). Different ramp rates of the turbine speed were tested out during the startup processes. Bypass valves were also used to manipulate the airflow during SOFC-GT hybrid system start-up process. Different ramp rates enable the rapid start-up of the turbine to avoid surge and stall, meanwhile enable acceptable warm rate of the fuel cell stack without damaging the cell material. CPS can enable dynamic characterizations of highly integrated systems at lower cost.

Zhou, Nana↗
DOE OSTI2025

Chemistry of Sugar Formation in the Gas Phase: Following the Activated Aldehyde

Sugars are produced by living organisms, and are required building blocks for life as we know it, which raises the foundational question of how sugars formed in a prebiotic environment. The abiotic formose reaction produces sugars from formaldehyde, but our understanding of its initiation step remains murky, with chemists invoking the concept of an “activated aldehyde” to seed this reaction. Singlet hydroxycarbenes, high-energy isomers of aldehydes, were recently reported to facilitate sugar formation under cold, nonaqueous conditions relevant to interstellar environments. Here, we generate singlet methylhydroxycarbene ( 1 CH 3 –C̈–OH) from the photodissociation of pyruvic acid and experimentally measure its gas-phase reaction with d 4 -acetaldehyde using multiplexed photoionization mass spectrometry. The C 4 H 4 D 4 O 2 isomer d 4 -acetoin is the sole product, which we kinetically link to the reactant CH 3 –C̈–OH, and attribute to a carbonyl-ene formation mechanism. We see no evidence of 3-hydroxybutanal, the C–H insertion product expected in carbene chemistry. Using automated exploration we calculate stationary points on the potential energy surface and report master equation rate coefficients from T = 20–600 K, providing quantitative kinetics of this fast reaction for use in chemical models. The prereactive complex in this reaction is stabilized by both hydrogen bonding and electrophilic carbene C═O interactions. These effects create a short-range dynamical bottleneck for the reaction besides the long- and midrange barrierless bottlenecks. Combined with recent reports of 1 HC̈OH production from methanol photodissociation and pyruvic acid production in cold irradiated ices, this work provides evidence that singlet hydroxycarbene + aldehyde chemistry is a feasible path to prebiotic sugar formation.

aldehydes↗
DOE OSTI2025

Near-cryogenic direct air capture using adsorbents

Direct air capture (DAC) of CO 2 is a key component in the portfolio of negative emissions technologies for mitigating global warming. However, even with the most potent amine sorbents, large-scale DAC deployment remains limited by high energy and capital costs. Recently, adsorbents relying on weak interactions with CO 2 have emerged as a potential alternative, thanks to their rapid adsorption kinetics and superior long-term stability, particularly under sub-ambient conditions (∼253 K). Despite these advantages, their use is hindered by the need for a water-removal process, location-specific constraints, and insufficient working capacity even in cold climates. In this study, we hypothesized that further reducing the adsorption temperature to a near-cryogenic range (160–220 K) could enable cost-effective DAC by utilizing the full potential of physisorbents. We primarily consider integrating DAC with a relatively untapped source of cold energy—liquified natural gas (LNG) regasification—to perform near-cryogenic DAC. From large-scale molecular simulations, Zeolite 13X and CALF-20 were identified as promising candidates. These materials were subsequently examined through experiments, including breakthrough analyses at 195 K. Their high CO 2 sorption capacity (4.5–5.5 mmol g −1 ), combined with a low desorption enthalpy and robust long-term stability, led to a threefold reduction in the levelized cost of capture (down to 68.2 USD per tonne CO 2 ). Estimates of the global LNG regasification resource suggest that LNG–DAC coupling could potentially enable the capture of 103–142 megatonnes of CO 2 annually as of 2050.

Kim, Seo-Yul [Georgia Institute of Technology, Atl↗
DOE OSTI2026

Understanding cold electron impact on parallel-propagating whistler chorus waves via moment-based quasilinear theory

Earth's magnetosphere hosts a wide range of collisionless particle populations that interact through various wave-particle processes. Among these, cold electrons, with energies below 100 eV, often dominate the plasma density but remain poorly characterized due to measurement challenges such as spacecraft charging and photoelectron contamination. Understanding the contribution of these cold populations to wave–particle interaction is of significant interest. Recent kinetic simulations identified a secondary drift-driven instability, in which parallel-propagating whistler-mode chorus waves excite oblique electrostatic whistler waves near the resonance cone and Bernstein-mode turbulence. These secondary modes enable a new channel of energy transfer from the parallel-propagating whistler wave to the cold electrons. In this work, we develop a moment-based quasilinear theory of the secondary instabilities to quantify such energy exchange. Our results show that these secondary instabilities persist for a wide range of parameters and, in many cases, lead to nearly complete damping of the primary wave. Such secondary instability might limit the amplitude of parallel-propagating whistler waves in Earth's magnetosphere and might explain why high-amplitude oblique whistler or electron Bernstein waves are rarely observed simultaneously with high-amplitude field-aligned whistler waves in the inner magnetosphere.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Mixed warm dark matter constraints using Milky Way satellite galaxy counts

Warm dark matter has been strongly constrained in recent years as the sole component of dark matter. However, a less-explored alternative is that dark matter consists of a mixture of warm and cold dark matter (MWDM). In this work, we use observations of Milky Way satellite galaxies to constrain MWDM scenarios where the formation of small-scale structure is suppressed either by generic thermal relic warm dark matter or a sterile neutrino produced through the Shi-Fuller mechanism. To achieve this, we model satellite galaxies by combining numerical simulations with semianalytical models for the subhalo population, and use a galaxy-halo connection model to match galaxies onto dark matter subhalos. By comparing the number of satellites predicted by MWDM models to the observed satellite population from the Dark Energy Survey and Pan-STARRS1, we constrain the fraction of warm dark matter, f WDM , as a function of its mass, m WDM . We exclude dark matter being composed entirely of thermal relic warm dark matter with m WDM ≤ 6.6 keV at a posterior ratio of 10 ∶ 1 , consistent with previous works. However, we find that warm dark matter with smaller mass is allowed when mixed with cold dark matter, and that the f WDM constraints strengthen with decreasing m WDM until they plateau at f WDM ≲ 0.45 for m WDM ≲ 1.5 keV . Likewise, in the case of a sterile neutrino with mass of 7 keV produced through the Shi-Fuller mechanism, we exclude a fraction of f ν s ≲ 0.45 , independent of mixing angle. Our results extend constraints on MWDM to a region of parameter space that has been relatively unconstrained with previous analysis.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Lifetime Energy Savings Via Advanced Manufacturing of Low Density Steels for Transportation Applications

The purpose of this “Low Density Steels for Transportation Applications” project was to develop an alloy composition and processing parameters that would result in a material suitable for use in automotive structural components at a reduced density over the current advanced high strength steel (AHSS) materials used. The project work successfully developed a robust alloy capable of exceeding project mechanical property targets at each stage of development, with an 8% density reduction over benchmark AHSS materials (7.8 g/cm3). The developed alloy has the potential to offer significant vehicle lightweighting and improved fuel economy, without sacrificing the increased passenger safety of more traditional AHSS. Through the three tasks of the project, (1) Alloy design and small-scale laboratory evaluation, (2) Laboratory development of hot rolled material and (3) Laboratory development of a cold rolled material, the laboratory work utilized advanced characterization and analytical methods on novel alloy compositions subjected to both conventional and non-conventional processing operations.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Air Source Heat Pumps in Cold Climates

This booklet is geared toward homeowners who want to learn about air source heat pumps and covers how the technology works, how it performs in various cold-climate environments, and NREL project highlights.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Temperature-based reactive flow model for triaminotrinitrobenzene (TATB) plastic bonded explosives

A new reactive flow model is presented for triaminotrinitrobenzene (TATB)-based plastic bonded explosives, applicable to shock initiation and steady detonation problems of differing initial temperature. Temperature disequilibrium is assumed between unreacted explosive, material in the vicinity of compressed defects (called hot spots), and reaction products. The model incorporates temperature-dependent decomposition reaction rates. Particularly, Arrhenius model parameters were derived from quantum-based molecular dynamics simulations of TATB decomposition. Further, a model of detonation carbon aggregation is incorporated, describing the slow release of energy inherent to detonation in TATB-based materials. Model parameters were calibrated against gas gun shock initiation experiments and steady detonation rate stick tests. The predictive ability of the model in the shock initiation regime is tested against recent thin pulse experiments. The model is found to perform equally well in predicting the size-effect curve of ambient, cold, and hot rate sticks. The present work demonstrates the viability of incorporating results from subscale simulations into a continuum-scale reactive flow model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗