Search NASA⌕ Search

SEARCH · Search NASA

Results for “CORROSION PREVENTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Removal of Surface Carbonate from Lithium-Ion Battery Cathode Materials via Vapor-Phase Fluorination

Herein, ultrathin metal-fluoride barrier coatings on the surface of lithium-ion battery (LIB) cathodes can improve cycling stability and prevent corrosion by acidic byproducts in the electrolyte. Atomic layer deposition (ALD) is an effective method to deposit ultrathin metal fluoride coatings on LIB cathodes. Although numerous studies have demonstrated the benefit of ALD metal fluoride coatings to LIB performance, comparatively few works have examined the effect of individual ALD precursors on the cathode surface. This paper uses X-ray photoelectron spectroscopy (XPS) measurements to elucidate the surface chemical changes on LIB cathode material surfaces upon exposure to the ALD metal fluoride precursor, hydrogen fluorine pyridine (HFPy). We found a decrease in surface carbonate and an increase in surface fluoride after HFPy exposure suggesting the conversion of lithium carbonate (Li 2 CO 3 ) to lithium fluoride (LiF). This conversion is desirable given that Li 2 CO 3 degrades LIB performance, whereas LiF provides an excellent physio-chemical barrier against chemical attack during cycling. Scanning transmission electron microscopy, X-ray energy dispersive spectroscopy, and XPS measurements following HFPy exposure to Li 2 CO 3 powder revealed the formation of a conformal LiF shell around the Li 2 CO 3 particles. Finally, we confirmed the complete conversion of similar to 7 nm ALD Li 2 CO 3 films on silicon from HFPy exposure using XPS and spectroscopic ellipsometry. The elimination of problematic Li 2 CO 3 from LIB cathode surfaces and conversion into a protective LiF coating via a single precursor vapor treatment may provide a cost-effective method for enhancing LIB performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Rugged bialkali photocathodes encapsulated with graphene and thin metal film

Protection of free-electron sources has been technically challenging due to lack of materials that transmit electrons while preventing corrosive gas molecules. Two-dimensional materials uniquely possess both of required properties. Here, we report three orders of magnitude increase in active pressure and factor of two enhancement in the lifetime of high quantum efficiency (QE) bialkali photocathodes (cesium potassium antimonide (CsK 2 Sb)) by encapsulating them in graphene and thin nickel (Ni) film. The photoelectrons were extracted through the graphene protection layer in a reflection mode, and we achieved QE of ~ 0.17% at ~ 3.4 eV, 1/e lifetime of 188 h with average current of 8.6 nA under continuous illumination, and no decrease of QE at the pressure of as high as ~ 1 × 10 –3 Pa. In comparison, the QE decreased drastically at 10 –6 Pa for bare, non-protected CsK 2 Sb photocathodes and their 1/e lifetime under continuous illumination was ~ 48 h. We attributed the improvements to the gas impermeability and photoelectron transparency of graphene.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Experimentally informed structure optimization of amorphous TiO 2 films grown by atomic layer deposition

Amorphous titanium dioxide TiO 2 (a-TiO 2 ) has been widely studied, particularly as a protective coating layer on semiconductors to prevent corrosion and promote electron–hole conduction in photoelectrochemical reactions. The stability and longevity of a-TiO 2 is strongly affected by the thickness and structural heterogeneity, implying that understanding the structure properties of a-TiO 2 is crucial for improving the performance. This study characterized the structural and electronic properties of a-TiO 2 thin films (~17 nm) grown on Si by atomic layer deposition (ALD). Fluctuation spectra V(k) and angular correlation functions were determined with 4-dimensional scanning transmission electron microscopy (4D-STEM), which revealed the distinctive medium-range ordering in the a-TiO 2 film. A realistic atomic model of a-TiO 2 was established guided by the medium-range ordering and the previously reported short-range ordering of a-TiO 2 film, as well as the interatomic potential. The structure was optimized by the StructOpt code using a genetic algorithm that simultaneously minimizes energy and maximizes the match to experimental short- and medium-range ordering. The StructOpt a-TiO 2 model presents improved agreements with the medium-range ordering and the k-space location of the dominant 2-fold angular correlations compared with a traditional melt-quenched model. The electronic structure of the StructOpt a-TiO 2 model was studied by ab initio calculations and compared to the crystalline phases and experimental results. Finally, this work uncovered the medium-range ordering in a-TiO 2 thin films and provided a realistic a-TiO 2 structure model for further investigation of structure–property relationships and materials design. In addition, the improved multi-objective optimization package StructOpt was provided for structure determination of complex materials guided by experiments and simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Aluminum hydroxide, bayerite, boehmite, and gibbsite ToF-SIMS spectra in the negative ion mode. I

We report time-of-flight secondary ion mass spectrometry (ToF-SIMS) was performed for boehmite (AOH-60) and its potential products of oxidation including pseudo-boehmite (AOH-180), α- and γ-Al 2 O 3 , and α- and γ-Al(OH) 3 . Since boehmite is often incorporated on cladding materials to prevent corrosion, surface analysis techniques are performed to determine the amount of oxidation present. This ToF-SIMS spectral library is of significance because it includes boehmite and its potential oxidation products (i.e., aluminum oxide and hydroxide), which can be used to compare to spectra obtained for real-world samples containing boehmite. Furthermore, ToF-SIMS is often used as a complementary technique to x-ray photoelectron spectroscopy due to its surface sensitivity and ability to compare spectra via a multivariate analysis, therefore establishing that the molecular signatures of boehmite and relevant compounds are essential for peak identification. The SIMS spectra shown are acquired from commercially available powders, which were deposited onto a silicon wafer substrate via liquid slurry drop casting. This library of SIMS mass spectra will serve as a comparison of boehmite [γ-AlO(OH)], pseudo-boehmite [AlOOH∙nH 2 O], α- and γ-Al 2 O 3 aluminum oxide, and α- and γ-Al 2 O 3 aluminum hydroxide in the negative ion mode, which compliments those reported in the positive ion mode.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Aluminum hydroxide, bayerite, boehmite, and gibbsite ToF-SIMS spectra in the positive ion mode. II

We report time-of-flight secondary ion mass spectrometry (ToF-SIMS) was performed for boehmite (AOH-60) and its potential products of oxidation including pseudo-boehmite (AOH-180), α- and γ-Al 2 O 3 , and α- and γ-Al(OH) 3 . Since boehmite often forms on the cladding materials to prevent corrosion, surface analysis techniques are performed to determine the amount of oxidation present. This ToF-SIMS spectral library is of significance because it includes boehmite and its potential oxidation products (i.e., aluminum oxide and hydroxide), which can be used to compare to spectra obtained for real-world samples containing boehmite. Furthermore, ToF-SIMS is often used as a complementary technique to x-ray photoelectron spectroscopy (XPS) due to its surface sensitivity and ability to compare spectra via multivariate analysis, therefore establishing the molecular signatures of boehmite and relevant compounds are essential for peak identification. The SIMS spectra shown are acquired from commercially available powders, which were deposited onto a Si wafer substrate via liquid slurry drop casting. This library of SIMS mass spectra will serve as a comparison of boehmite [γ-AlO(OH)], pseudo-boehmite [AlOOH∙nH 2 O], α- and γ-Al 2 O 3 aluminum oxide, and α- and γ-Al 2 O 3 aluminum hydroxide in the positive ion mode, which compliments those reported in the negative ion mode (Part 1).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Reduced Neutralization Feasibility Study for H-Canyon Accelerated Basin De- Inventory (ABD) Program

An alternative approach to Spent Nuclear Fuel (SNF) and Nuclear Material Processing was developed for future H-Canyon (HCAN) and L-Area operations that involves a paradigm shift from current HCAN, Concentrate, Storage, and Transfer Facility (CSTF), and Defense Waste Processing Facility (DWPF) operations. The alternative, referred to as Accelerated Basin De-inventory (ABD), requires that all Domestic and Foreign Research Reactor SNF currently at the Savannah River Site (SRS) will be dissolved, stored, and then transferred to CSTF without recovery of Highly Enriched Uranium (HEU). Concentrated nitric acid is utilized to dissolve aluminum spent nuclear fuel (ASNF) in HCAN. The vessels and piping in HCAN are fabricated from 304L stainless steel and are ideally suited to handle the acidic waste stream. However, as the waste is transferred to the CSTF and DWPF, it will contact the carbon steel waste tanks in CSTF. In order to prevent corrosion of the carbon steel, the acidic waste is neutralized (i.e., pH adjusted over 11) by the addition of sodium hydroxide (NaOH). The NaOH is added until the final solution contains 1.2 M excess -OH. Additionally, if the waste is not neutralized to a pH greater than 11, then aluminum hydroxide (Al(OH) 3 ) would form, and solids may form in the piping as it is transferred to CSTF. This document presents an analysis of the influence of reducing the excess caustic that is added to the neutralization tanks on the corrosion protection scheme primarily for the CSTF waste tanks. The implications to HCAN and DWPF were also assessed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Interactions of Aqueous Surface Treatments with Magnesium Alloy

Magnesium, the lightest structural metal, has recently been identified as an important substrate for weight reduction in automotive, aerospace, personal electronics, and many other industries. Magnesium’s unique chemistry, however, makes it challenging to protect from corrosion and incorporate with other materials. Cleaners are the first step in any pretreatment process, and understanding their role in surface preparation for corrosion prevention is crucial to making magnesium substrate a viable solution for lightweighting. In this work, we explore the relationship between cleaner composition, pH, etch rate, and panel morphology post-cleaning to understand how various cleaners interact with magnesium alloy. Our findings broaden the pool of possible bath chemistries that provide safe and effective surface cleaning of magnesium substrate.

Harris, Rachel↗
DOE OSTI2023

Anomaly Detection in Liquid Sodium Cold Trap Operation with Multisensory Data Fusion Using Long Short-Term Memory Autoencoder

Sodium-cooled fast reactors (SFR), which use high temperature fluid near ambient pressure as coolant, are one of the most promising types of GEN IV reactors. One of the unique challenges of SFR operation is purification of high temperature liquid sodium with a cold trap to prevent corrosion and obstructing small orifices. We have developed a deep learning long short-term memory (LSTM) autoencoder for continuous monitoring of a cold trap and detection of operational anomaly. Transient data were obtained from the Mechanisms Engineering Test Loop (METL) liquid sodium facility at Argonne National Laboratory. The cold trap purification at METL is monitored with 31 variables, which are sensors measuring fluid temperatures, pressures and flow rates, and controller signals. Loss-of-coolant type anomaly in the cold trap operation was generated by temporarily choking one of the blowers, which resulted in temperature and flow rate spikes. The input layer of the autoencoder consisted of all the variables involved in monitoring the cold trap. The LSTM autoencoder was trained on the data corresponding to cold trap startup and normal operation regime, with the loss function calculated as the mean absolute error (MAE). The loss during training was determined to follow log-normal density distribution. During monitoring, we investigated a performance of the LSTM autoencoder for different loss threshold values, set at a progressively increasing number of standard deviations from the mean. The anomaly signal in the data was gradually attenuated, while preserving the noise of the original time series, so that the signal-to-noise ratio (SNR) averaged across all sensors decreased below unity. Results demonstrate detection of anomalies with sensor-averaged SNR < 1.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Opportunities for Catalytic Reactions and Materials in Buildings

Residential and commercial buildings are responsible for over 30% of global final energy consumption and accounts for ~40% of annual direct and indirect greenhouse gas emissions. Energy efficient and sustainable technologies are necessary to not only lower the energy footprint but also lower the environmental burden. Many proven and emerging technologies are being pursued to meet the ever-increasing energy demand. Catalytic science has a significant new role to play in helping address sustainable energy challenges, particularly in buildings, compared to transportation and industrial sectors. Thermally driven heat pumps, dehumidification, cogeneration, thermal energy storage, carbon capture and utilization, emissions suppression, waste-to-energy conversion, and corrosion prevention technologies can tap into the advantages of catalytic science in realizing the full potential of such approaches, quickly, efficiently, and reliably. Catalysts can help increase energy conversion efficiency in building related technologies but must utilize low cost, easily available and easy-to-manufacture materials for large scale deployment. This entry presents a comprehensive overview of the impact of each building technology area on energy demand and environmental burden, state-of-the-art of catalytic solutions, research, and development opportunities for catalysis in building technologies, while identifying requirements, opportunities, and challenges.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A Direct Ammonia Fuel Cell with a KOH-Free Anode Feed Generating 180 mW cm −2 at 120 °C

The motivations to operate the direct ammonia fuel cell (DAFC) with no addition of aqueous base, include facilitated fuel management and prevention of corrosion and shunt currents in the DAFC stack. We describe here a polymer electrolyte DAFC, operating at a cell temperature (T cell ) of 120 °C on ammonia and water alone as anode feed, that demonstrated peak power of 180 mW cm −2 —a record for this type of fuel cell. We offer a detailed analysis of polarization curves recorded for PE-DAFCs in the T cell range of 60 °C–120 °C, allowing to estimate the effects of KOH-free operation on the ionic and faradaic resistances, R i and R F , that determine together the value of R app , CL – an , the apparent resistance of the anode catalyst layer. The latter resistance drops ten times between 60 °C and 120 °C as result mainly of the drop in R F . Consequently, DAFC performance at T cell > 100 °C improves substantially, including the cell performance on a KOH-free anode feed. The demsontrated performance levels reported here for KOH-free DAFCs support further development of this type of ammonia/air fuel cells.

Achrai, Ben↗
DOE OSTI2020

Drying Spent Magnox Fuel for Interim Dry Storage

Spent Magnox fuel is usually stored under water for shielding and cooling following use in-reactor, but the storage water can react with Magnox clad fuel and cause corrosion and forms a sludge which generates a secondary waste product. One option to prevent unwanted corrosion and avoid expensive waste management is to dry the wet fuel. This project aims to test a drying process which will convert wet and corroded Magnox fuel to a stable form to demonstrate viability for conversion from wet to dry storage. Samples of corroded Magnox supplied by National Nuclear Laboratory. Corrosion product retrieved by various methods including dry scraping, ultrasonic treatment to form sludge and sludge drying to isolate suspension. TGA undertaken on Sample 1 and Sample 2, with brucite and hydromagnesite for comparison. Both samples showed ∼10% mass loss up to 250 deg. C attributable to water held in sample. Mass loss from dehydroxylation which liberates further water in both samples. TGA data plotted alongside chemically pure brucite and hydromagnesite shows expected similarities/differences between Sample 1(mostly brucite) and Sample 2 (brucite/hydromagnesite mixture). Following treatment, dried samples observed to slowly gain mass in ambient conditions. Presumed to be hygroscopic absorption of air water vapour as effect is reversible, with similar effect observed for hydromagnesite and brucite. Etched Magnox vacuum dried for 3.5 h at 90 deg. C to test for reaction with residual water - some discoloration but no noticeable corrosion observed. Drying etched Magnox metal to observe surface effects/corrosion during drying process.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Sequential separation of battery electrode materials and metal foils in aqueous media

To recycle high-value lithium-ion battery components, it is imperative to efficiently separate electrode materials from current collector foils and to separate cathodes from anodes. This study investigates the delamination behaviors of cathodes and anodes from their respective current collectors in aqueous media. Whereas anode films can easily detach from copper foils in water, the delamination of cathode films does not exhibit the same behavior in water; instead, the cation exchange reaction results in lithium leaching and aluminum corrosion in the presence of water. Here, a buffer solution with surfactant additives has been designed to prevent aluminum corrosion and to improve solution wetting behavior, thereby facilitating cathode delamination. The delamination difference enables the sequential recovery of electrode materials and metal foils at different separation stages, simplifying the traditionally intricate processes within a one-pot recovery system. The recovered materials retain their crystal structure and morphology, and there are no signs of aluminum corrosion or residues on the metal foils. The sequential separation technique achieves nearly 100% separation efficiency for electrode materials from metal foils and over 98% separation efficiency for cathode and anode materials.

25 ENERGY STORAGE↗
DOE OSTI2022

ZnCr and ZnNb Cold Spray Coatings

Novel cold spray zinc-based alloy coatings have been investigated for corrosion protection of API 5L low carbon steel pipelines used in transporting natural gas. These different zinc alloy coatings are designed for use to help prevent internal corrosion and improve the lifespan of steel pipelines via sacrificial anodic protection. The corrosion behavior of these cold deposited zinc alloy coatings was investigated in CO2 saturated 3.5 wt.% NaCl solutions under simulated natural gas pipeline conditions. Electrochemical tests were conducted at 25 and 40 °C to determine the polarization resistance and galvanic current between each coating and the steel substrate in the galvanic couple. Tests were conducted at atmospheric, 1 bar, pressure. The results indicate that use of these coatings has the potential to increase the lifespan of steel pipelines above what a zinc coating alone could provide.

Teeter, Lucas↗
DOE OSTI2023

Development of an accelerator-based neutron source to prototype Mo-99 production, part I: A liquid LBE windowless target

In this article, Molybdenum-99 (Mo-99)’s decay product, technetium-99 (Tc-99 m), is one of the most critical isotopes for medical diagnostics. To provide U.S. domestic supply of Mo-99 without using high-enriched uranium (HEU), a subcritical uranium target assembly (UTA) is irradiated by an accelerator-based neutron source to create Mo-99 through fission. This study discusses the development of the accelerator-based neutron source. The high-energy electrons from the accelerator irradiate a liquid lead-bismuth eutectic (LBE) target to produce neutrons. Part I of this work focuses on numerical and experimental analysis towards the development of a liquid LBE windowless target. Unlike the existing windowless targets in literature, the current design creates a vertical free surface for a beam to irradiate. First, a hydrodynamic analysis of the LBE windowless target is performed. Simplified analytical calculations are assisted by 2D computational fluid dynamics (CFD) simulations to design the target, with the focus on eliminating recirculation zones and avoiding cavitation. With the optimized geometry, the experimental study is performed to investigate the flow hydrodynamics using liquid LBE. The experiments (1) compare pressure drop in the system to correlation predictions; (2) visualize the free surface liquid LBE flow from the beam view; (3) validate the LBE flow profile using temperature sensitive paint from the side view; and (4) validate the liquid LBE film thickness using gamma densitometer measurements. Second, the power handling capability of the designed windowless target is investigated. The divider plate in the current design is susceptible to overheating due to the thin LBE film in front. As LBE erosion and corrosion is likely to occur at an LBE velocity of 2.0 m/s and temperature above 500 °C, a power limit of 10 kW of beam power was established to prevent this corrosion from occurring, which is calculated by a Nusselt number correlation. The divider plate surface temperature at 10 kW agrees well with the 3D CFD simulation results. Part I demonstrates the fundamental physics in liquid LBE windowless target design and associated testing. A companion paper, Part II will demonstrate how to couple this windowless target into the Mo-99 production system, including an accelerator system operating under an ultra-high vacuum and the UTA cooled by water at room temperature.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Internal insulation and corrosion control of molten chloride thermal energy storage tanks

A chloride-based molten-salt system that uses a ternary blend of MgCl 2 /KCl/NaCl is investigated to provide higher-temperature thermal energy storage capability than conventional nitrate salt-based systems. Despite their high thermal stability and operating temperature, molten chlorides present several challenges, including the design of internal liners to prevent the corrosion and thermal stress of alloy tank shells. This work discusses issues and potential solutions related to containment of molten chloride salt, specifically the optimization of the hot face refractory materials for use as internal liners. Furthermore, three down-selected refractory materials were analyzed with respect to permeation of salt through the material as well as chemical stability during high temperature operation. Through the application of X-ray imaging and electron spectroscopy techniques, highly stable secondary surface phases in equilibrium with the molten salt were identified, as well as time-dependent changes in the salt composition itself.

25 ENERGY STORAGE↗