Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component Test Capability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Component Characterization of an eVTOL Reference Model for Crashworthiness Studies

Researchers at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) have conducted a series of structural component and seat level tests to improve finite element model (FEM) characterization of a representative vertical take-off and landing (eVTOL) test article developed by NASA. A full-scale dynamic test was conducted on the representative eVTOL test article in November of 2022. The test article represented a high wing, six passenger eVTOL design concept and is referred to as the lift plus cruise (LPC) test article. The full-scale test identified limitations in the analytical models used to predict aircraft structural response, in particular the composite material models did not effectively capture brittle failure of the structure which were measured during dynamic loading. To better understand the mechanism behind the composite material failure mechanisms observed and to improve the FEM, intact sample specimens of the composite airframe structure were recovered from the test article post-test and used in material characterization testing. In addition, the seat configurations used in the LPC test article were further studied using isolated seat and anthropomorphic test device (ATD) drop tower testing. Dynamic compression tests and three-point bend tests, conducted at varied impact speeds, were performed on the recovered frame section specimens. Additional testing was conducted to characterize the material properties of the forming foam, which remained in the frames after fabrication. These tests were used to improve characterization of the damage and failure parameters of the composite material model used in the FE model of the LPC test article. Seat level tests were conducted on the seats used in the LPC test article using acceleration pulses inclusive of current general aviation and rotorcraft certification load levels as well as conditions representative of those measured at the seat base during the LPC test. The structural material models and seat environment models of the LPC test article FEM were calibrated using the generated component test data. The updates made to these models were then integrated into the LPC FEM and simulated in the full-scale test condition. Results demonstrated the effectiveness of component testing to improve predictive capability of composite aerospace structural models within the crash and dynamic loading environments. Demonstration of the LPC FEM response across an accumulation of coupon, component, seat environment, and full-scale test levels provides confidence in the predictive capability of this model for future use in the study of occupant safety within eVTOL relevant crash environments.

Craswhorthiness↗

Engine component instrumentation development facility at NASA Lewis Research Center

The Engine Components Instrumentation Development Facility at NASA Lewis is a unique aeronautics facility dedicated to the development of innovative instrumentation for turbine engine component testing. Containing two separate wind tunnels, the facility is capable of simulating many flow conditions found in most turbine engine components. This facility's broad range of capabilities as well as its versatility provide an excellent location for the development of novel testing techniques. These capabilities thus allow a more efficient use of larger and more complex engine component test facilities.

Bruckner, Robert J.↗

Engine component instrumentation development facility at NASA Lewis Research Center

The Engine Components Instrumentation Development Facility at NASA Lewis is a unique aeronautics facility dedicated to the development of innovative instrumentation for turbine engine component testing. Containing two separate wind tunnels, the facility is capable of simulating many flow conditions found in most turbine engine components. This facility's broad range of capabilities as well as its versatility provide an excellent location for the development of novel testing techniques. These capabilities thus allow a more efficient use of larger and more complex engine component test facilities.

Bruckner, Robert J.↗

Payload and Components Real-Time Automated Test System (PACRATS), Data Acquisition of Leak Rate and Pressure Data Test Procedure

The purpose of this activity is to provide the Mechanical Components Test Facility (MCTF) with the capability to obtain electronic leak test and proof pressure data, Payload and Components Real-time Automated Test System (PACRATS) data acquisition software will be utilized to display real-time data. It will record leak rates and pressure/vacuum level(s) simultaneously. This added functionality will provide electronic leak test and pressure data at specified sampling frequencies. Electronically stored data will provide ES61 with increased data security, analysis, and accuracy. The tasks performed in this procedure are to verify PACRATS only, and are not intended to provide verifications for MCTF equipment.

Rinehart, Maegan L.↗

Survey of Facilities for Testing Photovoltaics

42-page report describes facilities capable of testing complete photovoltaic systems, subsystems, or components. Compilation includes facilities and capabilities of five field centers of national photovoltaics program, two state-operated agencies, and five private testing laboratories.

Weaver, R. W.↗

Component Level Regression Testing in a Hierarchical Architecture

The Goddard Earth Observing System (GEOS) is an Earth system model consisting of a large suite of individual model components that can be coupled in a flexible manner to investigate a variety of Earth science issues. Specific GEOS model configurations are composed as a hierarchical collection of components based on the Earth System Modeling Framework (ESMF). Regression testing of GEOS is currently limited to (1) full system tests that are poor at isolating specific defects and (2) a suite of unit tests which have very limited coverage. As part of our approach to improve upon the current testing situation, we have prototyped the capability to perform regression tests on individual GEOS components by leveraging and extending existing checkpoint/restart capabilities. In our implementation, each ESMF component has 3 states: Import (what it needs to run), Export (which it needs to provide to other components), and Internal (the component state proper). By capturing, Import, Export and Internal states for a given component during a ull run of GEOS, a generic driver can then rerun the component offline and compare expected exports with those that have been saved. The hierarchical structure of GEOS introduces an interesting wrinkle when trying to test components that in turn drive interacting child components. To fully isolate a parent component, we use the approach of software mocks, in which the exports of children are also saved during the initial capture run of GEOS. Then when testing the parent component, the children components are replaced by a generic mock component that produces exports from the previously saved data and ensures that that all interdependencies among children components are satisfied.

Thomas Clune↗

Component Level Testing in a Hierarchical Architecture

The Goddard Earth Observing System (GEOS) is an Earth system model consisting of a large suite of individual model components that can be coupled in a flexible manner to investigate a variety of Earth science issues. Specific GEOS model configurations are composed as a hierarchical collection of components based on the Earth System Modeling Framework (ESMF). Regression testing of GEOS is currently limited to (1) full system tests that are poor at isolating specific defects and (2) a suite of unit tests which have very limited coverage. As part of our approach to improve upon the current testing situation, we have prototyped the capability to perform regression tests on individual GEOS components by leveraging and extending existing checkpoint/restart capabilities. In our implementation, each ESMF component has 3 states: Import (what it needs to run), Export (which it needs to provide to other components), and Internal (the component state proper). By capturing, Import, Export and Internal states for a given component during a ull run of GEOS, a generic driver can then rerun the component offline and compare expected exports with those that have been saved. The hierarchical structure of GEOS introduces an interesting wrinkle when trying to test components that in turn drive interacting child components. To fully isolate a parent component, we use the approach of software mocks, in which the exports of children are also saved during the initial capture run of GEOS. Then when testing the parent component, the children components are replaced by a generic mock component that produces exports from the previously saved data and ensures that that all interdependencies among children components are satisfied.

Tom Clune↗

A Representative Shuttle Environmental Control System

The Representative Shuttle Environmental Control System (RSECS) provides a ground test bed to be used in the early accumulation of component and system operating data, the evaluation of potential system improvements, and possibly the analysis of Shuttle Orbiter test and flight anomalies. Selected components are being subjected to long term tests to determine endurance and corrosion resistance capability prior to Orbiter vehicle experience. Component and system level tests in several cases are being used to support flight certification of Orbiter hardware. These activities are conducted as a development program to allow for timeliness, flexibility, and cost effectiveness not possible in a program burdened by flight documentation and monitoring constraints.

Brose, H. F.↗

Electro-Mechanical Systems for Extreme Space Environments

Exploration beyond low earth orbit presents challenges for hardware that must operate in extreme environments. The current state of the art is to isolate and provide heating for sensitive hardware in order to survive. However, this protection results in penalties of weight and power for the spacecraft. This is particularly true for electro-mechanical based technology such as electronics, actuators and sensors. Especially when considering distributed electronics, many electro-mechanical systems need to be located in appendage type locations, making it much harder to protect from the extreme environments. The purpose of this paper to describe the advances made in the area of developing electro-mechanical technology to survive these environments with minimal protection. The Jet Propulsion Lab (JPL), the Glenn Research Center (GRC), the Langley Research Center (LaRC), and Aeroflex, Inc. over the last few years have worked to develop and test electro-mechanical hardware that will meet the stringent environmental demands of the moon, and which can also be leveraged for other challenging space exploration missions. Prototype actuators and electronics have been built and tested. Brushless DC actuators designed by Aeroflex, Inc have been tested with interface temperatures as low as 14 degrees Kelvin. Testing of the Aeroflex design has shown that a brushless DC motor with a single stage planetary gearbox can operate in low temperature environments for at least 120 million cycles (measured at motor) if long life is considered as part of the design. A motor control distributed electronics concept developed by JPL was built and operated at temperatures as low as -160 C, with many components still operational down to -245 C. Testing identified the components not capable of meeting the low temperature goal of -230 C. This distributed controller is universal in design with the ability to control different types of motors and read many different types of sensors. The controller form factor was designed to surround or be at the actuator. Communication with the slave controllers is accomplished by a bus, thus limiting the number of wires that must be routed to the extremity locations. Efforts have also been made to increase the power capability of these electronics for the ability to power and control actuators up to 2.5KW and still meet the environmental challenges. For commutation and control of the actuator, a resolver was integrated and tested with the actuator. Testing of this resolver demonstrated temperature limitations. Subsequent failure analysis isolated the low temperature failure mechanism and a design solution was negotiated with the manufacturer. Several years of work have resulted in specialized electro-mechanical hardware to meet extreme space exploration environments, a test history that verifies and finds limitations of the designs and a growing knowledge base that can be leveraged by future space exploration missions.

Mojarradi, Mohammad M.↗

Technology requirements for large flexible space structures

Research, test, and demonstration experiments necessary for establishing a data base that will permit construction of large, lightweight flexible space structures meeting on-orbit pointing and surface precesion criteria are discussed. Attention is focused on the wrap-rib proof-of-concept antenna structures developed from technology used on the ATS-6 satellite. The target structure will be up to 150 m in diameter or smaller, operate at RF levels, be amenable to packaging for carriage in the Shuttle bay, be capable of being ground-tested, and permit on-orbit deployment and retraction. Graphite/epoxy has been chosen as the antenna ribs material, and the antenna mesh will be gold-plated Mo wire. A 55-m diam reflector was built as proof-of-concept with ground-test capability. Tests will proceed on components, a model, the entire structure, and in-flight. An analytical model has been formulated to characterize the antenna's thermal behavior. The flight test of the 55-m prototype in-orbit offers the chance to validate the analytical model and characterize the control, mechanical, and thermal characteristics of the antenna configuration.

Wada, B. K.↗

AGT (Advanced Gas Turbine) technology project

An overall summary documentation is provided for the Advanced Gas Turbine Technology Project conducted by the Allison Gas Turbine Division of General Motors. This advanced, high risk work was initiated in October 1979 under charter from the U.S. Congress to promote an engine for transportation that would provide an alternate to reciprocating spark ignition (SI) engines for the U.S. automotive industry and simultaneously establish the feasibility of advanced ceramic materials for hot section components to be used in an automotive gas turbine. As this program evolved, dictates of available funding, Government charter, and technical developments caused program emphases to focus on the development and demonstration of the ceramic turbine hot section and away from the development of engine and powertrain technologies and subsequent vehicular demonstrations. Program technical performance concluded in June 1987. The AGT 100 program successfully achieved project objectives with significant technology advances. Specific AGT 100 program achievements are: (1) Ceramic component feasibility for use in gas turbine engines has been demonstrated; (2) A new, 100 hp engine was designed, fabricated, and tested for 572 hour at operating temperatures to 2200 F, uncooled; (3) Statistical design methodology has been applied and correlated to experimental data acquired from over 5500 hour of rig and engine testing; (4) Ceramic component processing capability has progressed from a rudimentary level able to fabricate simple parts to a sophisticated level able to provide complex geometries such as rotors and scrolls; (5) Required improvements for monolithic and composite ceramic gas turbine components to meet automotive reliability, performance, and cost goals have been identified; (6) The combustor design demonstrated lower emissions than 1986 Federal Standards on methanol, JP-5, and diesel fuel. Thus, the potential for meeting emission standards and multifuel capability has been initiated; (7) Small turbine engine aerodynamic and mechanical design capability has been initiated; and (8) An infrastructure of manpower, facilities, materials, and fabrication capabilities has been established which is available for continued development of ceramic component technology in gas turbine and other heat engines.

Source record↗

Long Life Technology Work at Rockwell International Space Division

This paper presents highlights of long-life technology oriented work performed at the Space Division of Rockwell International Corporation under contract to NASA. This effort included evaluation of Saturn V launch vehicle mechanical and electromechanical components for potential extended life capabilities, endurance tests, and accelerated aging experiments. A major aspect was evaluation of the components at the subassembly level (i.e., at the interface between moving surfaces) through in-depth wear analyses and assessments. Although some of this work is still in progress, preliminary conclusions are drawn and presented, together with the rationale for each. The paper concludes with a summary of the effort still remaining.

D K Huzel↗

Bioregenerative Planetary Life Support Systems Test Complex (BIO-Plex): NASA's Next Human-Rated Testing Facility

As a key component in its ground test bed capability, NASA's Advanced Life Support Program has been developing a large-scale advanced life support test facility capable of supporting long-duration evaluations of integrated bioregenerative life support systems with human test crews. This facility-targeted for evaluation of hypogravity compatible life support systems to be developed for use on planetary surfaces such as Mars or the Moon-is called the Bioregenerative Planetary Life Support Systems Test Complex (BIO-Plex) and is currently under development at the Johnson Space Center. This test bed is comprised of a set of interconnected chambers with a sealed internal environment which are outfitted with systems capable of supporting test crews of four individuals for periods exceeding one year. The advanced technology systems to be tested will consist of both biological and physicochemical components and will perform all required crew life support functions. This presentation provides a description of the proposed test "missions" to be supported by the BIO-Plex and the planned development strategy for the facility.

Tri, Terry O.↗

Oxidizer heat exchanger component test

The RL10-IIB engine, is capable of multimode thrust operation. The engine operates at two low-thrust levels: tank head idle (THI), approximately 1 to 2 percent of full thrust; and pumped idle, 10 percent of full thrust. Operation at THI provides vehicle propellant settling thrust and efficient thermal conditioning; PI operation provides vehicle tank prepressurization and maneuver thrust for low-g deployment. Stable combustion of the RL10-IIB engine during the low-thrust operating modes can be accomplished by using a heat exchanger to supply gaseous oxygen to the propellant injector. The oxidized heat exchanger (OHE) vaporizes the liquid oxygen using hydrogen as the energy source. This report summarizes the test activity and post-test data analysis for two possible heat exchangers, each of which employs a completely different design philosophy. One design makes use of a low-heat transfer (PHT) approach in combination with a volume to attenuate pressure and flow oscillations. The test data showed that the LHT unit satisfied the oxygen exit quality of 0.95 or greater in both the THI and PI modes while maintaining stability. The HHT unit fulfilled all PI requirements; data for THI satisfactory operation is implied from experimental data that straddle the exact THI operating point.

Kanic, P. G.↗

Signal Processing and Fault Detection with Application to CH-46 Helicopter Data

Central to Qualtech Systems' mission is its testability and maintenance software (TEAMS) and derivatives. Many systems comprise components equipped with self-testing capability; but, if the system is complex (and involves feedback and if the self-testing itself may occasionally be faulty) tracing faults to a single or multiple causes is difficult. However, even for systems involving many thousands of components the PC-based TEAMS provides essentially real-time system-state diagnosis. Until recently TEAMS operation was passive: its diagnoses were based on whatever data sensors could provide. Now, however, a signal-processing (SP) "frontend" matched to inference needs is available. Many standard signal processing primitives, such as filtering, spectrum analysis and multi-resolution decomposition are available; the SP toolbox is also equipped with a (supervised) classification capability based on a number of decision-making paradigms. This paper is about the SP toolbox. We show its capabilities, and demonstrate its performance on the CH-46 "Westland" data set.

Wen, Fang↗

Integrated Evaluation of Closed Loop Air Revitalization System Components

NASA s vision and mission statements include an emphasis on human exploration of space, which requires environmental control and life support technologies. This Contractor Report (CR) describes the development and evaluation of an Air Revitalization System, modeling and simulation of the components, and integrated hardware testing with the goal of better understanding the inherent capabilities and limitations of this closed loop system. Major components integrated and tested included a 4-Bed Modular Sieve, Mechanical Compressor Engineering Development Unit, Temperature Swing Adsorption Compressor, and a Sabatier Engineering and Development Unit. The requisite methodolgy and technical results are contained in this CR.

Murdock, K.↗

Capability for aerothermal-structural tests of large-to-full-scale components of future space transportation systems

The design of viable, low-mass thermostructural concepts for future space transportation systems requires accurate definition of the localized heat flux, pressures, and flow-surface interaction parameters for complex flow regions of detailed areas of large vehicles, such as wing-elevon coves, thermal protection system tile gaps, and corrugated metallic surfaces. This paper discusses investigations recently conducted in and planned for two high-energy wind tunnels at the Langley Research Center - the 8-foot High-temperatures Tunnel and the Thermal Protection System Test Facility. The data obtained on large-to-full-scale vehicle components, comparisons of the experimental data with theory, and the large, reusable, generalized test apparatus available at or planned for these facilities are discussed.

Couch, L. M.↗

A 10,000 hour endurance test of a 700 series 30 cm engineering model thruster

This paper describes a 10,000 hour test of the first engineering model of the 30-cm ion thruster which is expected to form the basis of future prime propulsion systems. This test demonstrated the lifetime capability of such critical components as cathodes, vaporizers, isolators, and optics. The results of the test are described including the conclusions derived from an extensive post-test analysis of the thruster. This test did identify a major life limiting problem - discharge chamber erosion. The modifications which have been incorporated in the 900 series 30-cm ion thrusters to minimize this problem are described.

Collett, C. R.↗