Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computational modeling, solid-state batteries, cathodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

22 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Atomic layer deposited aluminum nitride for interface protection of lithium germanium thiophosphate solid electrolytes

Lithium germanium thiophosphate (LGPS) is an attractive solid-state electrolyte material due to its exceptionally high ionic conductivity (~1.2 × 10 –2 S cm –1 ), comparable to many organic liquid electrolytes commonly used in batteries. Despite the high conductivity of LGPS, the susceptibility of LGPS to deleterious degradation reactions has impeded its commercial adoption into solid-state batteries. In particular, the poor voltage stability of LGPS with high-voltage cathode or lithium metal potentials often results in dramatically increasing cell impedance during galvanic cycling. Here, we use aluminum nitride (AlN) as a protection layer for Li metal anode, applied directly to the LGPS at 250 °C using plasma-enhanced atomic layer deposition, to enhance cell performance by preventing LGPS-Li metal reactions. We compare the surface chemistry and electrochemical cycling performance of atomic layer-deposited AlN grown using both plasma N 2 and NH 3 precursors. Galvanostatic cycling and electrochemical impedance spectroscopy show that AlN-coated LGPS cells perform better than bare LGPS cells in contact with Li metal anodes, with the AlN able to improve cycling longevity by over a factor of 3 in certain cases. Finally, we utilize x-ray photoelectron spectroscopy (XPS) line scans to highlight the slow room-temperature reactivity between AlN and evaporated lithium metal, and a computational model is built to aid further XPS analysis.

25 ENERGY STORAGE↗
DOE OSTI2025

Electrolytic gold plating, stripping, and ion transport dynamics through a solid-state iodide perovskite

The pronounced electrochemical reactivity between halide perovskites and metal electrodes can introduce mobile extrinsic metal ions which can cause device instability or enable novel functionalities. Here we systematically investigate the kinetics of gold cation (Au + ) migration in indium tin oxide (ITO)/methylammonium lead triiodide (MAPbI 3 )/Au model devices under long-term potentiostatic biasing. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) analyses reveal that Au + ions, electrochemically generated at the Au anode, traverse the perovskite layer with diffusion coefficients on the order of 10 −11 to 10 −10 cm 2 s −1 and are subsequently reduced at the cathode as Au 0 clusters, resembling metal plating behavior in electrolytic cells and solid-state batteries during charging. Furthermore, reversing the applied bias strips the plated Au 0 , revealing reversibility suitable for bipolar resistive switching devices and providing direct evidence of the electrochemical and ionic nature of Au transport within the perovskite matrix. Quantitatively determining diffusion coefficients and ion concentrations provides foundational inputs for future drift-diffusion modelling opportunities and allows us to relate our findings to implications on long term operation of devices like photovoltaic modules. These results clearly demonstrate the solid-state electrochemical nature of perovskite devices, highlight methods to be more quantitative about ion transport properties, provide and emphasize the importance of disentangling electro-, photo-, photoelectrochemical processes for understanding device performance and unlocking new functionalities.

14 SOLAR ENERGY↗