Results for “Continuous flow chemistry” — Page 2

NASA NTRS2018

One-Dimensional Modeling Methodology for Shock Tubes: Application to the EAST Facility

In this work, a one-dimensional methodology for simulating shock tubes is developed. The model accounts for the viscous interactions of the shock with the shock tube wall by adding an area change source term in the 1-D conservation equations corresponding to the boundary layer growth. This source term corresponds to the mass and energy going into the boundary layer. The boundary layer growth is computed using a simple model with a scaling factor. This scale factor is used to tailor a solution to match the deceleration profile of a shock tube test. In doing so, not only will the source term take into account boundary layer losses, it will also cover any effect due to radiative cooling loses from the gas. For this study, the Electric Arc Shock Tube(EAST) facility at NASA Ames Research Center is modeled for Earth reentry conditions. The purpose of this paper is to investigate if anomalies identified for certain conditions in the EAST data are due to shock deceleration. These anomalies include measuring electron number density above equilibrium predictions and observing that radiance profiles can continually increase behind the shock, never reach steady state, for certain shots (typically those less than 10 km/s). An eleven species air mixture is chosen to study the chemistry of the flow. Comparisons of the simulations to the experimental results are presented. Good agreement with the shock deceleration profiles was achieved by tuning in the boundary layer scale factor. The temperature as well as electron number density increases behind the shock, as has also been observed in the experiments. Finally, radiance comparisons between results from NEQAIR and experiments also show good agreement for some shots, but significant discrepancies are still observed for others.

Sharma, Maitreyee↗

NASA NTRS2018

One-Dimensional Modeling Methodology for Shock Tubes: Application to the EAST Facility

In this work, a one-dimensional methodology for simulating shock tubes is developed. The model accounts for the viscous interactions of the shock with the shock tube wall by adding an area change source term in the 1-D conservation equations corresponding to the boundary layer growth. This source term corresponds to the mass and energy going into the boundary layer. The boundary layer growth is computed using a simple model with a scaling factor. This scale factor is used to tailor a solution to match the deceleration profile of a shock tube test. In doing so, not only will the source term take into account boundary layer losses, it will also cover any effect due to radiative cooling loses from the gas. For this study, the Electric Arc Shock Tube(EAST) facility at NASA Ames Research Center is modeled for Earth reentry conditions. The purpose of this paper is to investigate if anomalies identified for certain conditions in the EAST data are due to shock deceleration. These anomalies include measuring electron number density above equilibrium predictions and observing that radiance profiles can continually increase behind the shock, never reach steady state, for certain shots (typically those less than 10 km/s). An eleven species air mixture is chosen to study the chemistry of the flow. Comparisons of the simulations to the experimental results are presented. Good agreement with the shock deceleration profiles was achieved by tuning in the boundary layer scale factor. The temperature as well as electron number density increases behind the shock, as has also been observed in the experiments. Finally, radiance comparisons between results from NEQAIR and experiments also show good agreement for some shots, but significant discrepancies are still observed for others.

Sharma, Maitreyee↗

NASA NTRS1992

An iodine hypersonic wind tunnel for the study of nonequilibrium reacting flows

A pilot scale hypersonic wind tunnel operating on pure iodine vapor has been designed and tested. The wind tunnel operates intermittently with a run phase lasting approximately 20 minutes. Successful recirculation of the iodine used during the run phase has been achieved but can be improved. Relevant issues regarding the full scale facility's design and operation, and the use of iodine as a working gas are discussed. Continuous wave laser induced fluorescence was used to monitor number densities within the plume flowfield, while pulsed laser induced fluorescence was used in an initial attempt to measure vibrational energy state population distributions. Preliminary nozzle flow calculations based on finite rate chemistry are presented.

Pham-Van-diep, G. C.↗

NASA NTRS1998

Studying Turbulence Using Numerical Simulation Databases: Proceedings of the Summer Program - No. 7

The Seventh Summer Program of the Center for Turbulence Research took place in the four-week period, July 5 to July 31, 1998. This was the largest CTR Summer Program to date, involving thirty-six participants from the U. S. and nine other countries. Thirty-one Stanford and NASA-Ames staff members facilitated and contributed to most of the Summer projects. A new feature, and perhaps a preview of the future programs, was that many of the projects were executed on non-NASA computers. These included supercomputers located in Europe as well as those operated by the Departments of Defense and Energy in the United States. In addition, several simulation programs developed by the visiting participants at their home institutions were used. Another new feature was the prevalence of lap-top personal computers which were used by several participants to carry out some of the work that in the past were performed on desk-top workstations. We expect these trends to continue as computing power is enhanced and as more researchers (many of whom CTR alumni) use numerical simulations to study turbulent flows. CTR's main role continues to be in providing a forum for the study of turbulence for engineering analysis and in facilitating intellectual exchange among the leading researchers in the field. Once again the combustion group was the largest. Turbulent combustion has enjoyed remarkable progress in using simulations to address increasingly complex and practically more relevant questions. The combustion group's studies included such challenging topics as fuel evaporation, soot chemistry, and thermonuclear reactions. The latter study was one of three projects related to the Department of Energy's ASCI Program (www.llnl.gov/asci); the other two (rocket propulsion and fire safety) were carried out in the turbulence modeling group. The flow control and acoustics group demonstrated a successful application of the so-called evolution algorithms which actually led to a previously unknown forcing strategy for jets yielding increased spreading rate. A very efficient algorithm for flow in complex geometries with moving boundaries based on the immersed boundary forcing technique was tested with very encouraging results. Also a new strategy for the destruction of aircraft trailing vortices was introduced and tested. The Reynolds Averaged Modeling (RANS) group demonstrated that the elliptic relaxation concept for RANS calculations is also applicable to transonic flows with shocks; however, prediction of laminar/turbulent transition remains an important pacing item. A large fraction of the LES effort was devoted to the development and testing of a new algorithmic procedure (as opposed to phenomenological model) for subgrid scale modeling based on regularized de-filtering of the flow variables. This appears to be a very promising approach, and a significant effort is currently underway to assess its robustness in high Reynolds number flows and in conjunction with numerical methods for complex flows. As part of the Summer Program two review tutorials were given on Turbulent structures in hydrocarbon pool fires (Sheldon Tieszen), and Turbulent combustion modeling: from RANS to LES via DNS (Luc Vervisch); and two seminars entitled Assessment of turbulence models for engineering applications (Paul Durbin) and Subgrid-scale modeling for non-premixed, turbulent reacting flows (James Riley) were presented. A number of colleagues from universities, government agencies, and industry attended the final presentations of the participants on July 31 and participated in the discussions. There are twenty-six papers in this volume grouped in five areas. Each group is preceded with an overview by its coordinator.

Source record↗

NASA NTRS2004

Fact Sheet: Range Complex

NASA Ames has a long tradition in leadership with the use of ballistic ranges and shock tubes for the purpose of studying the physics and phenomena associated with hypervelocity flight. Cutting-edge areas of research run the gamut from aerodynamics, to impact physics, to flow-field structure and chemistry. This legacy of testing began in the NACA era of the 1940's with the Supersonic Free Flight Tunnel, and evolved dramatically up through the late 1950s with the pioneering work in the Ames Hypersonic Ballistic Range. The tradition continued in the mid-60s with the commissioning of the three newest facilities: the Ames Vertical Gun Range (AVGR) in 1964, the Hypervelocity Free Flight Facility (HFFF) in 1965 and the Electric Arc Shock Tube (EAST) in 1966. Today the Range Complex continues to provide unique and critical testing in support of the Nation's programs for planetary geology and geophysics; exobiology; solar system origins; earth atmospheric entry, planetary entry, and aerobraking vehicles; and various configurations for supersonic and hypersonic aircraft.

Cornelson, C.↗

NASA NTRS1989

Aeroassist flight experiment aerodynamics and aerothermodynamics

The problem is to determine the transitional flow aerodynamics and aerothermodynamics, including the base flow characteristics, of the Aeroassist Flight Experiment (AFE). The justification for the computational fluid dynamic (CFD) Application stems from MSFC's system integration responsibility for the AFE. To insure that the AFE objectives are met, MSFC must understand the limitations and uncertainties of the design data. Perhaps the only method capable of handling the complex physics of the rarefied high energy AFE trajectory is Bird's Direct Simulation Monte Carlo (DSMC) technique. The 3-D code used in this analysis is applicable only to the AFE geometry. It uses the Variable Hard Sphere (VHS) collision model and five specie chemistry model available from Langley Research Center. The code is benchmarked against the AFE flight data and used as an Aeroassisted Space Transfer Vehicle (ASTV) design tool. The code is being used to understand the AFE flow field and verify or modify existing design data. Continued application to lower altitudes is testing the capability of the Numerical Aerodynamic Simulation Facility (NASF) to handle 3-D DSMC and its practicality as an ASTV/AFE design tool.

Brewer, Edwin B.↗

NASA NTRS1987

Application of a flux-split algorithm to chemically relaxing, hypervelocity blunt-body flows

Viscous, nonequilibrium, hypervelocity flow fields over two axisymmetric configurations are numerically simulated using a factored, implicit, flux-split algorithm. The governing gas-dynamic and species-continuity equations for laminar flow are presented. The gas-dynamics/nonequilibrium-chemistry coupling procedure is developed as part of the solution procedure and is described in detail. Numerical solutions are presented for hypervelocity flows over a hemisphere and over an axisymmetric aeroassisted orbital transfer vehicle using three different chemistry models. The gas models considered are those for an ideal gas, for a frozen gas, and for chemically relaxing air consisting of five species. The calculated results are compared with existing numerical solutions in the literature along the stagnation line of the hemisphere. The effects of free-stream Reynolds number on the nonequilibrium flow field are discussed.

Balakrishnan, A.↗

NASA NTRS1992

The future challenge for aeropropulsion

NASA's research in aeropropulsion is focused on improving the efficiency, capability, and environmental compatibility for all classes of future aircraft. The development of innovative concepts, and theoretical, experimental, and computational tools provide the knowledge base for continued propulsion system advances. Key enabling technologies include advances in internal fluid mechanics, structures, light-weight high-strength composite materials, and advanced sensors and controls. Recent emphasis has been on the development of advanced computational tools in internal fluid mechanics, structural mechanics, reacting flows, and computational chemistry. For subsonic transport applications, very high bypass ratio turbofans with increased engine pressure ratio are being investigated to increase fuel efficiency and reduce airport noise levels. In a joint supersonic cruise propulsion program with industry, the critical environmental concerns of emissions and community noise are being addressed. NASA is also providing key technologies for the National Aerospaceplane, and is studying propulsion systems that provide the capability for aircraft to accelerate to and cruise in the Mach 4-6 speed range. The combination of fundamental, component, and focused technology development underway at NASA will make possible dramatic advances in aeropropulsion efficiency and environmental compatibility for future aeronautical vehicles.

Rosen, Robert↗

NASA NTRS1982

Silicon production process evaluations

Chemical engineering analysis was continued for the HSC process (Hemlock Semiconductor Corporation) in which solar cell silicon is produced in a 1,000 MT/yr plant. Progress and status are reported for the primary engineering activities involved in the preliminary process engineering design of the plant base case conditions (96%), reaction chemistry (96%), process flow diagram (85%), material balance (85%), energy balance (60%), property data (60%), equipment design (40%), major equipment list (30%) and labor requirements (10%). Engineering design of the second distillation column (D-02, TCS column) in the process was completed. The design is based on a 97% recovery of the light key (TCS, trichlorosilane) in the distillate and a 97% recovery of the heavy key (TET, silicon tetrachloride) in the bottoms. At a reflux ratio of 2, the specified recovery of TCS and TET is achieved with 20 trays (equilibrium stages, N=20). Respective feed tray locations are 9, 12 and 15 (NF sub 1 = 9, NF sub 2 = 12,, and NF sub 3 = 15). A total condenser is used for the distillation which is conducted at a pressure of 90 psia.

Source record↗

NASA NTRS1991

An improved compression molding technology for continuous fiber reinforced composite laminate. Part 1: AS-4/LaRC-TPI 1500 (HFG) Prepreg system

Poor processability of fiber reinforced high performance polyimide thermoplastic resin composites is a well recognized issue which, in many cases, prohibits the fabrication of composite parts with satisfactorily consolidated quality. Without modifying the resin matrix chemistry, improved compression modeling procedures were proposed and investigated with the AS-4/LaRC-TPI 1500 High Flow Grade (HFG) prepreg system. Composite panels with excellent C-scans can be consistently molded by this method under 700 F and a consolidation pressure as low as 100 psi. A mechanism for the consolidation of the composite under this improved molding technique is discussed. This mechanism reveals that a certain degree of matrix shear and tow filament slippage and nesting between plies occur during consolidation, which leads to a reduction of the consolidating pressure necessary to offset the otherwise intimate inter fiber-fiber contact and consequently achieves a better consolidation quality. Outstanding short beam shear strength and flexural strength were obtained from the molded panels. A prolonged consolidation step under low pressure, i.e., 100 psi at 700 F for 75 minutes, was found to significantly enhance the composite mechanical properties.

Hou, Tan-Hung↗

NASA NTRS1989

Triton - Stratospheric molecules and organic sediments

Continuous-flow plasma discharge techniques show production rates of hydrocarbons and nitriles in N2 + CH4 atmospheres appropriate to the stratosphere of Titan, and indicate that a simple eddy diffusion model together with the observed electron flux quantitatively matches the Voyager IRIS observations for all the hydrocarbons, except for the simplest ones. Charged particle chemistry is very important in Triton's stratosphere. In the more CH4-rich case of Titan, many hydrocarbons and nitriles are produced in high yield. If N2 is present, the CH4 fraction is low, but hydrocarbons and nitriles are produced in fair yield, abundances of HCN and C2H2 in Triton's stratosphere exceed 10 to the 19th molecules/sq cm per sec, and NCCN, C3H4, and other species are predicted to be present. These molecules may be detected by IRIS if the stratosphere is as warm as expected. Both organic haze and condensed gases will provide a substantial UV and visible opacity in Triton's atmosphere.

Thompson, W. Reid↗

NASA NTRS1987

Computational chemistry

With the advent of supercomputers, modern computational chemistry algorithms and codes, a powerful tool was created to help fill NASA's continuing need for information on the properties of matter in hostile or unusual environments. Computational resources provided under the National Aerodynamics Simulator (NAS) program were a cornerstone for recent advancements in this field. Properties of gases, materials, and their interactions can be determined from solutions of the governing equations. In the case of gases, for example, radiative transition probabilites per particle, bond-dissociation energies, and rates of simple chemical reactions can be determined computationally as reliably as from experiment. The data are proving to be quite valuable in providing inputs to real-gas flow simulation codes used to compute aerothermodynamic loads on NASA's aeroassist orbital transfer vehicles and a host of problems related to the National Aerospace Plane Program. Although more approximate, similar solutions can be obtained for ensembles of atoms simulating small particles of materials with and without the presence of gases. Computational chemistry has application in studying catalysis, properties of polymers, all of interest to various NASA missions, including those previously mentioned. In addition to discussing these applications of computational chemistry within NASA, the governing equations and the need for supercomputers for their solution is outlined.

Arnold, J. O.↗

NASA NTRS1990

A three-dimensional upwind parabolized Navier-Stokes code for chemically reacting flows

A new upwind, parabolized Navier-Stokes (PNS) code has been developed to compute the three-dimensional flow of chemically reacting air around hypersonic vehicles. The code is a modification of the perfect gas, three-dimensional UPS code of Lawrence et al. (1986) which has been extended in the present study to permit the calculation of hypersonic, viscous flows in chemical nonequilibrium. The algorithm solves the PNS equations using a finite-volume, upwind TVD method based on Roe's approximate Riemann solver that has been modified to account for real gas effects. The present code solves the fluid dynamic and species continuity equations in a loosely-coupled manner. The fluid medium is assumed to be a chemically reacting mixture of thermally perfect (but calorically imperfect) gases in thermal equilibrium. Results are presented for the hypersonic laminar flow over a cone at 0- and 10-deg angles of attack and for a generic hypersonic vehicle. Calculations are performed assuming either perfect gas, equilibrium air, or finite-rate chemistry.

Buelow, Philip E.↗

NASA NTRS1989

Aerodynamic stability and heating analyses for the aeroassist flight experiment vehicle

Since ground based flow simulations are presently unable to model flight conditions expected for AOTVs (Aeroassist Orbital Transfer Vehicle) and other hypersonic space vehicles, computer codes are being developed to provide design parameters necessary for structure, guidance, and control aspects. Over the past four years, VRFLO (Viscous Reactive Flow) has been written to model finite-rate chemistry and viscous effects for a variety of aerobrake bodies. VRFLO includes a number of unique features that are summarized as follows: (1) Grid generation is an integral part of the code for several aerobrake configurations which includes the wake flow region; (2) The formulation is valid for three air chemical models; (3) An ADI central difference technique is used to solve the Navier-Stokes and species continuity equations in split groups; and (4) Grid density and numerical damping are minimized by shock-fitting and conformal mapping of body points.

Mcgary, J.↗

NASA NTRS1990

Numerical study of shock-wave/boundary layer interactions in premixed hydrogen-air hypersonic flows

A computational study of shock wave/boundary layer interactions involving premixed combustible gases, and the resulting combustion processes is presented. The analysis is carried out using a new fully implicit, total variation diminishing (TVD) code developed for solving the fully coupled Reynolds-averaged Navier-Stokes equations and species continuity equations in an efficient manner. To accelerate the convergence of the basic iterative procedure, this code is combined with vector extrapolation methods. The chemical nonequilibrium processes are simulated by means of a finite-rate chemistry model for hydrogen-air combustion. Several validation test cases are presented and the results compared with experimental data or with other computational results. The code is then applied to study shock wave/boundary layer interactions in a ram accelerator configuration. Results indicate a new combustion mechanism in which a shock wave induces combustion in the boundary layer, which then propagates outwards and downstream. At higher Mach numbers, spontaneous ignition in part of the boundary layer is observed, which eventually extends along the entire boundary layer at still higher values of the Mach number.

Yungster, Shaye↗

NASA NTRS1991

Numerical study of shock-wave/boundary layer interactions in premixed hydrogen-air hypersonic flows

A computational study of shock wave/boundary layer interactions involving premixed combustible gases, and the resulting combustion processes is presented. The analysis is carried out using a new fully implicit, total variation diminishing (TVD) code developed for solving the fully coupled Reynolds-averaged Navier-Stokes equations and species continuity equations in an efficient manner. To accelerate the convergence of the basic iterative procedure, this code is combined with vector extrapolation methods. The chemical nonequilibrium processes are simulated by means of a finite-rate chemistry model for hydrogen-air combustion. Several validation test cases are presented and the results compared with experimental data or with other computational results. The code is then applied to study shock wave/boundary layer interactions in a ram accelerator configuration. Results indicate a new combustion mechanism in which a shock wave induces combustion in the boundary layer, which then propagates outwards and downstream. At higher Mach numbers, spontaneous ignition in part of the boundary layer is observed, which eventually extends along the entire boundary layer at still higher values of the Mach number.

Yungster, Shaye↗

NASA NTRS1994

A commercialized, continuous flow fiber optic sensor for trichloroethylene and haloforms

Purus, Inc. has commercialized a fiber optic chemical sensor using technology developed by Lawrence Livermore National Laboratory and licensed from The University of California. The basis for the sensor is the development of color within a reagent when exposed to an analyte. The sensor consists of an optrode, reagent delivery and recover system, fiber optic transmitter-receiver, controller, and display. Reagent is pumped through the optrode. Analyte diffuses across a gas permeable membrane and reacts with the reagent to form a colored product. The colored product is detected by measuring the absorbance of light from a 568 nm diode. Reagents are currently available for TCE and trihalomethanes. Initial reagent chemistry is based on the Fujiwara alkaline pyridine reaction. The optrode contacts only gas streams, but the volatility of the current analytes also allows measurements of aqueous streams, without being affected by aqueous interferents that are non-volatile. Sensitivity of the sensor has been demonstrated to 5 ppb aqueous solutions and 0.1 ppmv in flowing gas streams.

Wells, James C.↗

NASA NTRS1976

Mixing and combustion of an underexpanded H2 jet in supersonic flow

Theoretical calculations are compared with experimental data in an investigation of the injection, mixing, and combustion of an underexpanded hydrogen jet in a supersonic test stream. The experimental tests in reacting and nonreacting flows were conducted by use of air and nitrogen as test media. Tests were conducted in a free jet and a ducted mode. Theoretical calculations were performed with a modified viscous characteristics analysis. The computer program employs finite rate chemistry and a turbulent viscosity model which varies radially and axially; it handles exit shock waves, expansion fans, and thermal compressions generated in the reacting flow fields. Comparison of the theory and experimental data indicates good agreement for the near flow field; this agreement is directly related to the explicit handling of the near-field shock and expansion waves. Less satisfactory agreement at downstream locations for both free jet and ducted flows is attributed to the lack of continued computation of the shocks and expansions in the far field.

Jenkins, R. V.↗