Search NASA⌕ Search

SEARCH · Search NASA

Results for “Continuous manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Fracture and fatigue of discontinuously reinforced copper/tungsten composites

The strength, toughness and resistance to cyclic crack propagation of composites consisting of copper reinforced with short tungsten wires of various lengths have been studied and the results compared with the behavior of continuously reinforced composites manufactured by the same method, i.e., by vacuum hot-pressing. It has been found that whereas the resistance to fatigue crack growth of continuously reinforced composites is very similar to that of continuous Al/stainless steel composites reported elsewhere, the addition of short fibers completely changes the mode of fracture, and no direct comparisons are possible. In effect, short fibers inhibit single crack growth by causing plastic flow to be distributed rather than localized, and although these composites are much less strong than continuous fiber composites, they nevertheless have much greater fatigue resistance.

Harris, B.↗
NASA NTRS1999

Effect of High Temperature on the Tensile Behavior of CFRP and Cementitious Composites

Concrete and other composite manufacturing processes are continuing to evolve and become more and more suited for use in non-Earth settings such as the Moon and Mars. The fact that structures built in lunar environments would experience a range of effects from temperature extremes to bombardment by micrometeorites and that all the materials for concrete production exist on the Moon means that concrete appears to be the most feasible building material. it can provide adequate shelter from the harshness of the lunar environment and at the same time be a cost effective building material. With a return to the Moon planned by NASA to occur after the turn of the century, it will be necessary to include concrete manufacturing as one of the experiments to be conducted in one of the coming missions. Concrete's many possible uses and possibilities for manufacturing make it ideal for lunar construction. The objectives of this research are summarized as follows: i) study the possibility of concrete production on the Moon or other planets, ii) study the effect of high temperature on the tensile behavior of concrete, and iii) study the effect of high temperature on the tensile behavior of carbon fiber reinforced with inorganic polymer composites. Literature review indicates that production of concrete on the Moon or other planets is feasible using the indigenous materials. Results of this study has shown that both the tensile strength and static elastic modulus of concrete decreased with a rise in temperature from 200 to 500 C. The addition of silica fume to concrete showed higher resistance to high temperatures. Carbon fiber reinforced inorganic polymer (CFRIP) composites seemed to perform well up to 300 C. However, a significant reduction in strength was observed of about 40% at 400 C and up to 80% when the specimens were exposed to 700 C.

Toutanji, Houssam A.↗
NASA NTRS1993

NASA's Advanced solid rocket motor

The Advanced Solid Rocket Motor (ASRM) will not only bring increased safety, reliability and performance for the Space Shuttle Booster, it will enhance overall Shuttle safety by effectively eliminating 174 failure points in the Space Shuttle Main Engine throttling system and by reducing the exposure time to aborts due to main engine loss or shutdown. In some missions, the vulnerability time to Return-to-Launch Site aborts is halved. The ASRM uses case joints which will close or remain static under the effects of motor ignition and pressurization. The case itself is constructed of the weldable steel alloy HP 9-4-0.30, having very high strength and with superior fracture toughness and stress corrosion resistance. The internal insulation is strip-wound and is free of asbestos. The nozzle employs light weight ablative parts and is some 5,000 pounds lighter than the Shuttle motor used to date. The payload performance of the ASRM-powered Shuttle is 12,000 pounds higher than that provided by the present motor. This is of particular benefit for payloads delivered to higher inclinations and/or altitudes. The ASRM facility uses state-of-the-art manufacturing techniques, including continuous propellant mixing and direct casting.

Mitchell, Royce E.↗
NASA NTRS1993

Flexible storage medium for write-once optical tape

A write-once data storage media was developed which is suitable for optical tape applications. The media is manufactured using a continuous film process to deposit a ternary alloy of tin, bismuth, and copper. This laser sensitive layer is sputter deposited onto commercial plastic web as a single-layer thin film. A second layer is sequentially deposited on top of the alloy to enhance the media performance and act as an abrasion resistant hard overcoat. The media was observed to have laser write sensitivities of less than 2.0 njoules/bit, carrier-to-noise levels of greater than 50dB's, modulation depths of approximately 100 percent, read-margins of greater than 35, uniform grain sizes of less than 200 Angstroms, and a media lifetime that exceeds 10 years. Prototype tape media was produced for use in the CREO drive system. The active and overcoat materials are first sputter deposited onto three mil PET film in a single pass through the vacuum coating system, and then converted down into multiple reels of 35mm x 880m tape. One mil PET film was also coated in this manner and then slit and packaged into 3480 tape cartridges.

Strandjord, Andrew J. G.↗
NASA NTRS1993

Lithium D-cell study

The purpose of this contract is to evaluate parametrically the effects of various factors including the electrolyte type, electrolyte concentration, depolarizer type, and cell configuration on lithium cell electrical performance and safety. This effort shall allow for the selection and optimization of cell design for future NASA applications while maintaining close ties with WGL's continuous improvements in manufacturing processes and lithium cell design. Taguchi experimental design techniques are employed in this task, and allow for a maximum amount of information to be obtained while requiring significantly less cells than if a full factorial design were employed. Acceptance testing for this task is modeled after the NASA Document EP5-83-025, Revision C, for cell weights, OCV's and load voltages. The performance attributes that are studied in this effort are fresh capacity and start-up characteristics evaluated at two rates and two temperatures, shelf-life characteristics including start-up and capacity retention, and iterative microcalorimetry measurements. Abuse testing includes forced over discharge at two rates with and without diode protection, temperature tolerance testing, and shorting tests at three rates with the measurement of heat generated during shorting conditions.

Size, P.↗
NASA NTRS2003

Progress in GaAs Metamorphic HEMT Technology for Microwave Applications. High Efficiency Ka-Band MHEMT Power MMICs

This paper reviews recent progress in the development of GaAs metamorphic HEMT (MHEMT) technology for microwave applications. Commercialization has begun, while efforts to further improve performance, manufacturability and reliability continue. We also report the first multi-watt MHEMT MMIC power amplifiers, demonstrating up to 3.2W output power and record power-added efficiency (PAE) at Ka-band.

Smith, P. M.↗
NASA NTRS2009

Lightning Pin Injection Testing on MOSFETS

Lightning transients were pin-injected into metal-oxide-semiconductor field-effect transistors (MOSFETs) to induce fault modes. This report documents the test process and results, and provides a basis for subsequent lightning tests. MOSFETs may be present in DC-DC power supplies and electromechanical actuator circuits that may be used on board aircraft. Results show that unprotected MOSFET Gates are susceptible to failure, even when installed in systems in well-shielded and partial-shielded locations. MOSFET Drains and Sources are significantly less susceptible. Device impedance decreased (current increased) after every failure. Such a failure mode may lead to cascading failures, as the damaged MOSFET may allow excessive current to flow through other circuitry. Preliminary assessments on a MOSFET subjected to 20-stroke pin-injection testing demonstrate that Breakdown Voltage, Leakage Current and Threshold Voltage characteristics show damage, while the device continues to meet manufacturer performance specifications. The purpose of this research is to develop validated tools, technologies, and techniques for automated detection, diagnosis and prognosis that enable mitigation of adverse events during flight, such as from lightning transients; and to understand the interplay between lightning-induced surges and aging (i.e. humidity, vibration thermal stress, etc.) on component degradation.

Ely, Jay J.↗
NASA NTRS2021

A Summary of Normal Incidence Tube Tests of NASA'S Bio-inspired Broadband Acoustic Absorber

Motivated by the need to reduce noise pollution from aircraft engines, NASA has continued to design, manufacture and test recently patented structures that mimic the geometry and the broadband and low frequency acoustic absorption of assemblies of natural reeds. This report documents a screening test, which is a precursor to more controlled modelling experiments. The purpose of this experiment was to identify variables and prototype design features that might play a dominant role in the acoustic performance of these structures. To date, twenty-four prototypes, each with an overall shape of a cube (nominally 50 mm x 50 mm x 50 mm), were designed and additively manufactured from thermoplastics using a Fused Filament Fabrication technique. The prototypes were tested in the NASA Glenn and Langley Normal Incidence Tubes to experimentally determine the acoustic absorption as a function of frequency from 400 Hz to 3000 Hz. Results indicate that a variety of structures exhibit substantial acoustic absorption in that frequency range, with an average absorption coefficient greater than 0.6, especially in the frequency range of 400 Hz to 1000 Hz. Six basic prototype designs were chosen to inform future modeling research. Results of these experiments can be used to evaluate existing physics-based models of the interaction of sound waves with these structures or to develop new models. Validated physics-based models of these structures can help engineers optimize the designs for different commercial noise control applications.

Acoustics↗
NASA NTRS1976

SAMIS - A simulation of the solar array manufacturing industry

SAMIS is a continuing activity of the Project Analysis and Integration Task of the Low-cost Silicon Solar Array Project (LSSA). It provides a standardized procedure for producing reliable estimates of the cost of manufacturing solar arrays or their components. These estimates are based on descriptions of the manufacturing processes which are being studied and developed by LSSA subcontractors and will be used to assess the commercial viability of those processes and to set research priorities.

Chamberlain, R. G.↗
NASA NTRS2004

Particulate Titanium Matrix Composites Tested--Show Promise for Space Propulsion Applications

Uniformly distributed particle-strengthened titanium matrix composites (TMCs) can be manufactured at lower cost than many types of continuous-fiber composites. The innovative manufacturing technology combines cold and hot isostatic pressing procedures to produce near-final-shape components. Material stiffness is increased up to 26-percent greater than that of components made with conventional titanium materials at no significant increase in the weight. The improved mechanical performance and low-cost manufacturing capability motivated an independent review to assess the improved properties of ceramic titanium carbide (TiC) particulate-reinforced titanium at elevated temperature. Researchers at the NASA Glenn Research Center creatively designed and executed deformation and durability tests to reveal operating regimes where these materials could lower the cost and weight of space propulsion systems. The program compares the elevated-temperature performance of titanium alloy Ti-6Al-4V matrix material to an alloy containing 10 wt% of TiC particles. Initial experiments showed that at these relatively low particle concentrations the material stiffness of the TMC was improved 20 percent over that of the plain Ti-6Al-4V alloy when tested at 427 C. The proportional limit and ultimate strength of the composite in tension are 21- and 14-percent greater than those of the plain alloy. Compression tests showed that the proportional limit is about 30 percent greater for TMC than for the plain alloy. The enhanced deformation resistance of the TMC was also evident in a series of tensile and compressive stress relaxation tests that were made. Specimens were subjected to tensile or compressive strain amplitudes of 0.75 percent for 24 hr followed by a return to zero strain imposed for 24 hr. The stress relaxation data were normalized with respect to the maximum stress for each case and plotted as a function of time in the following graph. Tensile stresses relaxed 19 percent for the TMC and 25 percent for the plain Ti-6Al-4V alloy. Compressive stresses relaxed 25 percent for the TMC and 39 percent for the plain Ti-6Al-4V alloy. The superior deformation resistance of the TMC extends to a creep rate that is 28-percent slower for the TMC when it is loaded to stress levels that are 26-percent higher than for the plain Ti-6Al-4V alloy.

Lerch, Bradley A.↗
NASA NTRS2019

NASA’s In-Space Manufacturing Project: Update on Manufacturing Technologies and Materials to Enable More Sustainable and Safer Exploration

NASA’s In-Space Manufacturing (ISM) project seeks to develop the materials, processes, and manufacturing technologies needed to provide an on-demand manufacturing capability for deep space exploration missions. The ability to manufacture and recycle some parts on demand rather than launch them from earth has the potential to reduce logistics requirements on long duration missions and enhance crew safety. With the launch of the first 3D printer (built and operated by Made in Space through a Small Business Innovative Research – SBIR -- contract) to the International Space Station (ISS) in 2014, the ISM project demonstrated the feasibility of operating an on-demand manufacturing system in a microgravity environment. This paper will provide an update on recent advancements in ISM under three key technology areas: manufacturing, recycling, and development of a design database. ISM continues to pursue development of manufacturing technologies for space applications and use the ISS as a critical test bed to prove out these technologies before deploying them on next generation exploration systems. Activities under this focus area include: characterization of materials manufactured using the Additive Manufacturing Facility (AMF), the second generation commercial 3D-printer on ISS, also owned and operated by Made in Space; development of prototype payloads for metal manufacturing through phase II SBIR contracts with Tethers Unlimited, Made in Space, and Ultra Tech Machinery; development of a multi-material fabrication laboratory capable of processing metals and providing inspection of manufactured parts through a Broad Agency Announcement (Techshot, Interlog, and Tethers Unlimited); an in-line sensing system for ISM platforms; and development of higher strength feedstocks for 3D polymer printers. In the area of recycling, the Tethers Unlimited Refabricator payload (an integrated 3D printer and recycler for ULTEM 9085) launched to ISS in November 2018 and began operating in early 2019. This payload represents the first demonstration of on-orbit recycling; down massed specimens will assess material degradation in the polymer over multiple recycling cycles to define limits on material re-use. Other work in the recycling area includes development of common use materials intended to be reused and recycled on space missions (Tethers Unlimited and Cornerstone Research Group) and a sterilization capability for multiple-use materials (ERASMUS from Tethers Unlimited). Concurrent with manufacturing technology and materials development work is creation of a design database, a curated list of parts that can be manufactured using the suite of In-Space Manufacturing capabilities.

Tracie Prater↗
NASA NTRS2007

Larger, Lighter Space Telescopes by Implementing In-Space Manufacturing Concepts

There is a continuous demand for larger, lighter, and higher quality telescopes from both the astronomical and global surveillance communities one looking up and the other down. Enabling technologies must be developed and implemented that will allow this goal to be financially and technically feasible. The optical systems needed far high spatial resolution surveillance and astronomical applications require large optical, apertures with mention of future systems up to 150 meter in diameter. With traditional optical manufacturing technologies, large optical aperture means high mass and long fabrication lead times with associated high costs. Completely new approaches to optical fabrication must be developed to enable the fabrication of such optical systems. The cost and lead time associated with the fabrication of lightweight, high quality optical systems limits the feasible size of the optics. A primary factor in the launch cost of space optical systems is volume and mass. To minimize the mass of the high quality optics, optical fabricators implement materials with high specific stiffness and use honeycomb, or other structural minimization patterns, to support the optical surface; however, the structure must still be designed to survive launch loads. This sigmficantly adds to the fabrication difficulty and dramatically increases launch costs. One approach to minimizing launch volume and negating the need for the design to survive launch loads is to send the manufacturing facility and raw materials into space and perform the fabrication in-situ. We, are currently performing feasibility studies of initial concepts for inspace manufacturing of optical systems. By utilizing the micro-gravity and vacuum environment of space while eliminating the constraints defined by high launch forces and limited volume of the launch vehicle, the development of large, high quality glass membrane mirrors may be feasible. Several concepts were investigated to address the manufacturing of both optical surfaces and telescope structure. We will describe one of the primary approaches to utilize the space environment for optical manufacturing and describe initial results.

Mooney, James t.↗
NASA NTRS1979

Large area CCD image sensors for space astronomy

The Defense Advanced Research Projects Agency (DARPA) has a substantial program to develop a 2200 x 2200 pixel CCD (Charge Coupled Device) mosaic array made up of 400 individual CCD's, 110 x 110 pixels square. This type of image sensor appeared to have application in space and ground-based astronomy. Under this grant a CCD television camera system was built which was capable of operating an array of 4 CCD's to explore the suitability of the CCD's to explore the suitability of the CCD for astronomical applications. Two individual packaged CCD's were received and evaluated. Evaluation of the basic characteristics of the best individual chips was encouraging, but the manufacturer found that their yield in manufacturing this design is two low to supply sufficient CDD's for the DARPA mosaic array. The potential utility of large mosaic arrays in astronomy is still substantial and continued monitoring of the manufacturers progress in the coming year is recommended.

Schwarzschild, M.↗
NASA NTRS2015

Low Cost Upper Stage-Class Propulsion (LCUSP)

NASA is making space exploration more affordable and viable by developing and utilizing innovative manufacturing technologies. Technology development efforts at NASA in propulsion are committed to continuous innovation of design and manufacturing technologies for rocket engines in order to reduce the cost of NASA's journey to Mars. The Low Cost Upper Stage-Class Propulsion (LCUSP) effort will develop and utilize emerging Additive Manufacturing (AM) to significantly reduce the development time and cost for complex rocket propulsion hardware. Benefit of Additive Manufacturing (3-D Printing) Current rocket propulsion manufacturing techniques are costly and have lengthy development times. In order to fabricate rocket engines, numerous complex parts made of different materials are assembled in a way that allow the propellant to collect heat at the right places to drive the turbopump and simultaneously keep the thrust chamber from melting. The heat conditioned fuel and oxidizer come together and burn inside the combustion chamber to provide thrust. The efforts to make multiple parts precisely fit together and not leak after experiencing cryogenic temperatures on one-side and combustion temperatures on the other is quite challenging. Additive manufacturing has the potential to significantly reduce the time and cost of making rocket parts like the copper liner and Nickel-alloy jackets found in rocket combustion chambers where super-cold cryogenic propellants are heated and mixed to the extreme temperatures needed to propel rockets in space. The Selective Laser Melting (SLM) machine fuses 8,255 layers of copper powder to make a section of the chamber in 10 days. Machining an equivalent part and assembling it with welding and brazing techniques could take months to accomplish with potential failures or leaks that could require fixes. The design process is also enhanced since it does not require the 3D model to be converted to 2-D drawings. The design and fabrication process can be sped up and improved with fewer errors to be accomplished in weeks instead of months.

Vickers, John↗
NASA NTRS1994

Environmentally sound manufacturing

The NASA/Thiokol/industry team has developed and started implementation of an environmentally sound manufacturing plan for the continued production of solid rocket motors. They have worked with other industry representatives and the U.S. Environmental Protection Agency to prepare a comprehensive plan to eliminate all ozone depleting chemicals from manufacturing processes and to reduce the use of other hazardous materials used to produce the space shuttle reusable solid rocket motors. The team used a classical approach for problem solving combined with a creative synthesis of new approaches to attack this problem. As our ability to gather data on the state of the Earth's environmental health increases, environmentally sound manufacturing must become an integral part of the business decision making process.

Caddy, Larry A.↗
NASA NTRS1990

Manufacture of bulk superconducting YBa2Cu3O(7-delta) by a continuous process

The development of a continuous process for fabricating large bulk superconductors with a predetermined grain orientation is reported. A bar of the 123 compound with dimensions 5 x 0.5 x about 0.3 cm with excellent grain alignment has been fabricated continuously. The bulk 123 thus obtained has magnetically determined J(c)s of about 30,000 and 12,000 A/sq cm at 0 and 1 T, respectively, and transport J(c)s of 20,000, 11,000, and 7500 A-sq cm at 0, 0.54, and 0.83 T.

Meng, R. L.↗
NASA NTRS1984

Solidification interface shape for continuous casting in an offset mold - Two analytical methods

A solution method for finding the unknown solidification interface in manufacturing slab ingots as a continuous casting is presented, which involves a product solution in the potential plane and the use of conjugate harmonic functions. It is argued that the method may be more direct for some geometries than the Cauchy boundary value method. Moreover, the usefulness of the Cauchy boundary value method is demonstrated through the example of a nonsymmetric horizontal mold where the walls are offset to support the lower ingot boundary.

Siegel, R.↗
NASA NTRS1994

Reduced hazard chemicals for solid rocket motor production

During the last three years. the NASA/Thiokol/industry team has developed and started implementation of an environmentally sound manufacturing plan for the continued production of solid rocket motors. NASA Marshall Space Flight Center (MSFC) and Thiokol Corporation have worked with other industry representatives and the U.S. Environmental Protection Agency (EPA) to prepare a comprehensive plan to eliminate all ozone depleting chemicals from manufacturing processes and reduce the use of other hazardous materials used to produce the space shuttle reusable solid rocket motors. The team used a classical approach for problem-solving combined with a creative synthesis of new approaches to attack this challenge.

Larry A. Caddy↗