SEARCH · Search NASA

Results for “Correlation of Full-Scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1975

An experimental investigation of heat transfer to reusable surface insulation tile array gaps in a turbulent boundary layer with pressure gradient

An experimental investigation was performed to determine the effect of pressure gradient on the heat transfer to space shuttle reusable surface insulation (RSI) tile array gaps under thick, turbulent boundary layer conditions. Heat transfer and pressure measurements were obtained on a curved array of full-scale simulated RSI tiles in a tunnel wall boundary layer at a nominal freestream Mach number of 10.3 and freestream unit Reynolds numbers of 1.6, 3.3, and and 6.1 million per meter. Transverse pressure gradients were induced over the model surface by rotating the curved array with respect to the flow. Definition of the tunnel wall boundary layer flow was obtained by measurement of boundary layer pitot pressure profiles, and flat plate wall pressure and heat transfer. Flat plate wall heat transfer data were correlated and a method was derived for prediction of smooth, curved array heat transfer in the highly three-dimensional tunnel wall boundary layer flow and simulation of full-scale space shuttle vehicle pressure gradient levels was assessed.

Throckmorton, D. A.↗

NASA NTRS1975

Full-scale upper-surface-blown flap noise

A highly noise-suppressed TF 34 engine was used to investigate the noise of several powered lift configurations involving upper-surface-blown (USB) flaps. The configuration variables were nozzle type (i.e. slot and circular with deflector), flap chord-length, and flap angle. The results of velocity surveys at both the nozzle exit and the flap trailing edge are used for correlation of the noise data. Configurations using a long flap design were 4 dB quieter than a short flap typical of current trends in USB flap design. The lower noise for the long flap is attributed primarily to the greater velocity decay of the jet at the flap trailing edge. The full-scale data revealed substantially more quadrupole noise in the region near the deflected jet than observed in previous sub-scale tests.

Heidelberg, L. J.↗

NASA NTRS1952

Axial-slot Air Admission for Controlling Performance of a One-quarter-annulus Turbojet Combustor and Comparison with Complete Engine

An investigation of a single-annulus turbojet combustor with slot-type air admission was conducted to demonstrate the application of certain design principles to the control of outlet-gas temperature distributions. Comparisons of performance of a one-quarter-annulus combustor (duct-type installation) and a full-annulus combustor (obtained in a full-scale turbojet engine) are presented to indicate the applicability of results obtained from combustion studies conducted in duct-type installations. A reasonable correlation existed between the performance of the one-quarter-annulus and full-annulus combustors except for temperature distribution. Sufficient trends did exist which made it possible to predict temperature distributions for the engine, although absolute correlation did not exist. A radial temperature distribution similar to that required for a given engine was obtained using a one-quarter-annulus duct-type setup to predict results.

COMBUSTION--TURBINE ENGINES↗

NASA NTRS1974

Dynamics of tilting proprotor aircraft in cruise flight

A nine degree-of-freedom theoretical model is developed for investigations of the dynamics of a proprotor operating in high inflow axial flight on a cantilever wing. The basic characteristics of the rotor high inflow aerodynamics and the resulting rotor aeroelastic behavior are discussed. The problems of classical whirl flutter, the two-bladed rotor, and the influence of the proprotor on the stability derivatives of the aircraft are treated briefly. The influence of various elements of the theoretical model is discussed, including the modeling used for the blade and wing aerodynamics, and the influence of the rotor lag degree of freedom. The results from tests of two full-scale proprotors - a gimballed, stiff-inplane rotor and a hingeless, soft-inplane rotor - are presented; comparisons with the theoretical results show good correlation.

Johnson, W.↗

NASA NTRS1936

Investigation of Full-Scale Split Trailing-Edge Wing Flaps with Various Chords and Hinge Locations

This report gives the results of an investigation conducted in the NACA full-scale wind tunnel on a small parasol monoplane equipped with three different split trailing-edge wing flaps. The object of the investigation was to determine and correlate data on the characteristics of the airplane and flaps as affected by variation in flap chord, flap deflection, and flap location along the wing chord. The results give the lift, the drag, and the pitching moment characteristics of the airplane, and the flap forces and moments, the pressure distribution over the flaps and wing at one section, and the downwash characteristics of the flap and wing combinations.

Wallace, Rudolf↗

NASA NTRS1971

Apollo telescope mount thermal systems unit thermal vacuum test

The Apollo Telescope Mount's thermal systems unit was utilized to conduct a full-scale thermal vacuum test to verify the thermal design and the analytical techniques used to develop the thermal mathematical models. Thermal vacuum test philosophy, test objectives configuration, test monitoring, environment simulation, vehicle test performance, and data correlation are discussed. Emphasis is placed on planning and execution of the thermal vacuum test with particular attention on problems encountered in conducting a test of this maguitude.

Trucks, H. F.↗

NASA NTRS1974

Full-scale aircraft cabin flammability tests of improved fire-resistant materials

Full-scale aircraft cabin flammability tests to evaluate the effectiveness of new fire-resistant materials by comparing their burning characteristics with those of older aircraft materials are described. Three tests were conducted and are detailed. Test 1, using pre-1968 materials, was run to correlate the procedures and to compare the results with previous tests by other organizations. Test 2 included newer, improved fire-resistant materials. Test 3 was essentially a duplicate of test 2, but a smokeless fuel was used. Test objectives, methods, materials, and results are presented and discussed. Results indicate that the pre-1968 materials ignited easily, allowed the fire to spread, produced large amounts of smoke and toxic combustion products, and resulted in a flash fire and major fire damage. The newer fire-resistant materials did not allow the fire to spread. Furthermore, they produced less, lower concentrations of toxic combustion products, and lower temperatures. The newer materials did not produce a flash fire.

Stuckey, R. N.↗

NASA NTRS1973

Sea level side loads in high-area-ratio rocket engines

An empirical separation and side load model to obtain applied aerodynamic loads has been developed based on data obtained from full-scale J-2S (265K-pound-thrust engine with an area ratio of 40:1) engine and model testing. Experimental data include visual observations of the separation patterns that show the dynamic nature of the separation phenomenon. Comparisons between measured and applied side loads are made. Correlations relating the separation location to the applied side loads and the methods used to determine the separation location are given.

Nave, L. H.↗

NASA NTRS1974

Aeroelastic-stability characteristics of a V/STOL tilt-rotor aircraft with hingeless blades - Correlation of analysis and test

The potential aeroelastic problems of a tilt rotor aircraft are described. The type of mathematical model required to predict such behavior is discussed and results of a design study on a specific configuration are presented. The sensitivity of the results to variation of the structural parameters is evaluated. The methodology used for analytical studies is shown to predict accurately the behavior of a full-scale rotor-pylon-wing system tested in the NASA-Ames 40- by 80-foot wind tunnel. It is concluded that there is no impediment from an aeroelastic viewpoint in designing and flying a tilt-rotor aircraft using a soft-in-plane hingeless rotor.

Alexander, H. R.↗

NASA NTRS1938

Full-Scale Wind-Tunnel Investigation of Wing Cooling Ducts, Special Report

The systematic investigation of wing cooling ducts at the NACA laboratory has been continued with tests in the full-scale wind tunnel on ducts of finite span. These results extend the previous investigation on section characteristics of ducts to higher Reynolds numbers and indicate the losses due to the duct ends. The data include comparisons between ducts completely within the ring and the conventional underslung ducts. Methods of flow regulation were studied and data were obtained for a wide range of internal duct resistance. The results show satisfactory correlation between the finite span and the previously measured section characteristics obtained with full-span ducts. The effects of the various design parameters on the duct characteristics are discussed. The cooling power required for the internal duct installation is shown to be only a small percentage of the engine power.

Nickle, F. R.↗

NASA NTRS1974

Free-flight investigation of the stability and control characteristics of a STOL model with an externally blown jet flap

The stability and control characteristics of a four-engine turbofan STOL transport model having an externally blown jet flap have been investigated by means of the flying-model technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated under conditions of symmetric and asymmetric (one engine inoperative) thrust at lift coefficients up to 9.5 and 5.5, respectively. Static characteristics were studied by conventional power-on force tests over the flight-test angle-of-attack range including the stall. In addition to these tests, dynamic longitudinal and lateral stability calculations were performed for comparison with the flight-test results and for use in correlating the model results with STOL handling-qualities criteria.

Parlett, L. P.↗

NASA NTRS1974

Effects of several factors on theoretical predictions of airplane spin characteristics

The influence of different mathematical and aerodynamic models on computed spin motion was investigated along with the importance of some of the aerodynamic and nonaerodynamic quantities defined in these models. An analytical technique was used which included the aerodynamic forces and moments acting on a spinning aircraft due to steady rotational flow and the contribution of the rotary derivatives to the oscillatory component of the total angular rates. It was shown that (1) during experimental-analytical correlation studies, the flight-recorded control time histories must be faithfully duplicated since the spinning motion can be sensitive to a small change in the application of the spin entry controls; (2) an error in the assumed inertias, yawing moments at high angle of attack, and initial spin entry bank angle do not influence the developed spin significantly; (3) damping in pitch derivatives and the center of gravity location play a role in the spinning motion; and (4) the experimental spin investigations conducted in a constant atmospheric density environment duplicate the Froude number only at the initial full-scale spin altitude (since the full-scale airplane at high altitudes experiences large density changes during the spin.)

Bihrle, W., Jr.↗

NASA NTRS1973

Shockwave-boundary layer interference heating analysis.

Interference heating correlations have been developed based on existing wind tunnel test data taken with simple configurations such as wedge/flat plate and compression corner models. For turbulent flow, peak interference heating was first correlated with shock strength (pressure ratio across shock wave) and then as a function of Reynolds number. The peak interference Stanton number was found to exhibit the same Reynolds number and Prandtl number characteristics as the Stanton number variation for undisturbed flow over a flat plate. Similar correlations were developed for laminar flow. Results indicated that for laminar flow at higher Reynolds number, the impinging shockwave may act as a boundary layer trip and cause boundary layer transition resulting in high interference heating. The correlations derived in this study can be used to scale wind tunnel model test data to a full-scale space vehicle at supersonic or hypersonic flight conditions.

Hung, F. T.↗

NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an EBF STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An UTW powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An OTW configuration with non-decayer nozzle was about 10 db quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗

NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Vonglahn, U.↗

NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Von Glahn, U.↗

NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an externally blown flap (EBF) STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An under the wing (UTW) powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An over the wing (OTW) configuration with nondecayer nozzle was about 10 dB quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗

NASA NTRS1947

Correlation of the Trim Limits of Stability Obtained for a PB2Y-3 Flying Boat and a 1/8-Size Powered Dynamic Model

Tests of a PB2Y-3 flying boat were made at the U.S> Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap deflection showed good agreement for the airplane and model. The lower trim limits obtained at different gross loads for the full-size airplane were reduced to approximately a single curve by plotting trim against the square root of C(sub delta (sub o)) divided by C(sub V).

Garrison, Charlie C.↗